Filters
total: 1229
filtered: 1078
displaying 1000 best results Help
Search results for: FLEXURAL TENSILE STRENGTH
-
Example of tension fabric structure analysis
PublicationThe aim of the work is to examine two variants of non-linear strain-stress relations accepted to description of architectural fabric. Discussion on the fundamental equations of the dense net model, used in description of coated woven fabric behaviour is presented. An analysis of tensile fabric structures subjected to the dead load and initial pretension is described.
-
Nano soil improvement technique using cement
PublicationNano soil-improvement is an innovative idea in geotechnical engineering. Nanomaterials are among the newest additives that improve soil properties. Herein, laboratory tests, such as unconfined compressive strength, direct shear test, and initial tests, were conducted to investigate the geotechnical properties of Kelachay clay with micro- and nanosized cement to evaluate its particles in untreated soil and observe changes in the...
-
Experiments and calibration of a bond-slip relation and efficiency factors for textile reinforcement in concrete
PublicationTextile reinforcement yarns consist of many filaments, which can slip relative each other. At modelling of the global structural behaviour, interfilament slip in the yarns, and slip between the yarns and the concrete can be considered by efficiency factors for the stiffness and strength of the yarns, and by applying a bond-slip relation between yarns and concrete. In this work, an effective and robust method for calibration of...
-
Badania wytrzymałościowe zgrzein łączących pręty zbrojeniowe o średnicy Ø30mm
PublicationZakres badań dotyczy oceny wytrzymałościowej zgrzein doczołowych, wykonanych metodą zwarciową. Elementami zgrzewanymi były pręty zbrojeniowe o średnicy Ø30mm. Badania związane są z okresową kontrolą stabilności parametrów zgrzewarki, szczególnie w odniesieniu do górnych, dopuszczalnych przez producenta zakresów parametrów zgrzewania oraz analizą wyników i porównaniu rezultatów prób wytrzymałościowych uzyskanych w 2019 i 2020 w...
-
Some problems of slide bearing material fatigue evaluation.
PublicationA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Processing of point cloud data retrieved from terrestrial laser scanning for structural modeling by Finite Element Method
PublicationFinite Element Method is one most popular contemporary method of strength analysis. The method is an advanced method for solving differential equations, based on discretization, which means that area is divided into finite elements. Each finite element has a solution of the equation approximated by specific functions and performing the actual calculations only for nodes of this division. Finite Element Method is widely used in...
-
Właściwości termoizolacyjne kompozytu wapienno-cementowego z udziałem paździerzy konopnych=Thermal insulation properties of the lime-cement composite with hemp shives
PublicationPrzedstawiono wyniki badań kompozytów wykonanych na bazie wapna budowlanego, cementu i dolomitu - spoiwa wiążącego z udziałem paździerzy konopi. Określono ich podstawowe właściwości, tj.: gęstość objętościową, współczynnik przewodzenia ciepła oraz wytrzymałości na ściskanie. Otrzymane wyniki dowodzą, że wytworzone kompozyty wapienno-cementowe z udziałem paździerzy konopnych są lekkie i charakteryzują się niskim współczynnikiem...
-
Simulations of Shear Zones and Cracks in Engineering Materials Using eXtended Finite Element Method
PublicationNumerical simulations of cracks and shear zones in quasi-brittle materials are presented. Extended Finite Element Method is used to describe both cracks and shear zones. In a description of tensile cracks, a Rankine criterion is assumed. A discrete Mohr-Coulomb law is adopted for simulations of shear zones. Results of simple numerical tests: unixial tension, bending and biaxial compression are demonstrated.
-
Bioactive polyurethanes applied as a surgical implants
PublicationSynthetic materials are applied in many branches of the industry, i.a. in medicine as a casing of apparatus, elements of artificial organs (hearts, blood vessels), catheters, wound healings, intra aortic balloons, mammary implants to mention but a few. Polymeric material used in such applications must be distinguished by a good biocompatybility. Since many years extensive research are employed to develop a new polymers that can...
-
Eco-friendly Route for Thermoplastic Polyurethane Elastomers with Bio-based Hard Segments Composed of Bio-glycol and Mixtures of Aromatic–Aliphatic and Aliphatic–Aliphatic Diisocyanate
PublicationApplication of bio-based diisocyanates with low volatility instead petrochemical diisocyanates has positive impact on environment by reduction of hazardous effects on living organisms and lead to bio-based polyurethanes (bio-PUs) with good usage properties. This work was focused on the synthesis and chosen properties examination of partially bio-based thermoplastic polyurethane elastomers (bio-PUs) obtained using diisocyanate mixtures,...
-
Polyurethanes Crosslinked with Poly(vinyl alcohol) as a Slowly-Degradable and Hydrophilic Materials of Potential Use in Regenerative Medicine
PublicationNovel, slowly-degradable and hydrophilic materials with proper mechanical properties and surface characteristics are in great demand within the biomedical field. In this paper, the design, synthesis, and characterization of polyurethanes (PUR) crosslinked with poly(vinyl alcohol) (PVA) as a new proposition for regenerative medicine is described. PVA-crosslinked PURs were synthesized by a two-step polymerization performed in a solvent...
-
Shear resistance of low height precast concrete lintels
PublicationThe scope of the paper is to investigate analytically and determine experimentally the shear resistance of low height reinforced precast concrete lintels. The chosen procedures included in national and international standards applied for the design of structural concrete elements to an estimation of shear behaviour of reinforced concrete elements are described. The characteristic and designed shear strength of precast concrete...
-
Eksperymentalna weryfikacja procedury szacowania wytrzymałości młodego betonu wg normy ASTM C1074
PublicationW referacie przedstawiono metodę służącą oszacowaniu wytrzymałości betonu w trakcie procesu dojrzewania (ang. Maturity Method) bazującą na procedurze określonej zgodnie z amerykańską normą, która uwzględnia wpływ połączonych efektów temperatury i czasu na rozwój wytrzymałości betonu. Standardy ASTM C1074 zostały opracowane przez NBS (ang. National Bureau of Standards) z uwagi na powtarzające się wypadki na palcu budowy wynikające...
-
Badania mieszanek mineralno-asfaltowych w niskiej temperaturze
PublicationW artykule przedstawiono metody badań w niskiej temperaturze betonu asfaltowego przeznaczonego do warstwy ścieralnej. Przedstawione zostały wyniki badań dla 4 różnych metod badawczych: zginania, pełzania, pośredniego rozciągania oraz rozciągania termicznego przy ograniczonym odkształceniu (test TSRST). Próbki betonu asfaltowego były przygotowywane w laboratorium z wykorzystaniem 3 rodzajów asfaltów: asfaltu zwykłego, asfaltu modyfikowanego...
-
Parametry mechaniczne platformy roboczej na podstawie badań DMT
PublicationNośność platformy roboczej określana jest w sposób analogiczny do nośności podłoża uwarstwionego, w którym warstwa wierzchnia zbudowana z gruntu niespoistego spoczywa na słabonośnym podłożu z gruntu spoistego. Badanie DMT wykorzystano do wyznaczenia parametrów wytrzymałościowych podłoża (kąta tarcia wewnętrznego warstwy górnej i wytrzymałości na ścinanie bez odpływu podłoża słabonośnego) oraz do wyznaczenia modułu odkształcenia...
-
Processing, Performance Properties, and Storage Stability of Ground Tire Rubber Modified by Dicumyl Peroxide and Ethylene-Vinyl Acetate Copolymers
PublicationIn this paper, ground tire rubber was modified with dicumyl peroxide and a variable content (in the range of 0–15 phr) of ethylene-vinyl acetate copolymers characterized by different vinyl acetate contents (in the range of 18–39 wt.%). Modification of ground tire rubber was performed via an auto-thermal extrusion process in which heat was generated during internal shearing of the material inside the extruder barrel. The processing,...
-
Buckling analyses of cylindrical metal silos containing bulk solids
PublicationThe paper presents quasi-static 3D buckling analysis results of thin-walled cylindrical metal silos with and without bulk solids. The behaviour of the bulk solid was described with a hypoplastic constitutive model. Non-linear analyses with geometric and material non-linearity were performed with a perfect and an imperfect silo shell. Different initial geometric imperfections were considered. The influence of internally stored bulk...
-
SUBSOIL CHARACTERISTICS OF THE VISTULA RIVER DIKES
PublicationThe results of CPTU tests are used to determine the strength parameters of a dike subsoil. Stress state and stress history of the subsoil under the flood embankment was evaluated with CPTU and DMT tests. Normally consolidated soil was found under the central part of the dike, while the subsoil near the dike toe is found to be overconsolidated. Due to consolidation the undrained shear strength of the subsoil under the central part...
-
Effect of long term service at elevated temperatures on mechanical properties of Manaurite XM reformer tubes
PublicationMicrostructure transformations occur in the Manaurite XM cast steel tubes during long-term operation in the reformer furnace were revealed and described. The rela tionship between mechanical properties, an increase of internal diameter of the tube and microstructure degradation is discussed. Static tensile test was performed on two types of samples with different shapes. It has been shown differences in the results of tests...
-
Wyznaczanie wytrzymałości betonu na podstawie funkcji dojrzałości wg amerykańskiej normy ASTM C1074-11
PublicationArtykuł poświęcono wyznaczaniu wytrzymałości betonu na podstawie funkcji dojrzałości wg normy ASTM C1074-11 (ang. Maturity Method). Metoda bazuje na rejestracji zmian tem - peratury w trakcie hydratacji dojrzewającego betonu. Wartykule zaprezentowano procedurę badawczą służącą wyznaczeniu funk - cji dojrzałości dla wybranej mieszanki betonowej oraz zależności wytrzymałość-dojrzałość. Celem badań jest wyznaczanie zmian w czasie...
-
Bearing capacity of the working platform with kinematic method
PublicationBearing capacity of the working platform for heavy tracks was analysed using Distinct Layout Optimization (DLO) method. The platform layer constructed from cohesionless soils is resting on weak cohesive subgrade. Different thickness of the platform, its effective angle of internal friction and undrained shear strength of the soft soil were taken into consideration. Kinematic method permits different failure mechanisms to be analyzed....
-
Mechanical properties of polyvinyl chloride-coated fabric under cyclic tests
PublicationThe aim of the present paper is to propose a method of laboratory tests necessary for the identification of mechanical properties of the coated fabric. The material parameters of the coated fabric AF 9032 are specified on the basis of the uniaxial and biaxial tensile tests. For the identification process, the techniques based on the least squares methods are used. Additionally, the uniaxial and biaxial cyclic tests are performed...
-
Rheological, Mechanical, Microstructural and Radiation Shielding Properties of Cement Pastes Containing Magnetite (Fe3O4) Nanoparticles
PublicationThis work examines the influence of iron oxide nanoparticles (Fe3O4 NPs) on neutron and gamma-ray radiation shielding characteristics of Portland cement paste. Experimental evaluations were supplemented with theoretical studies using NXCom program. Portland cement pastes with 5, 10, 15, 20, and 30 wt% of nanomagnetite cement replacement were produced. Moreover, rheological, early strength development, compressive strength, and...
-
Meso‐scale analyses of size effect in brittle materials using DEM
PublicationThe paper describes numerical meso-scale results of a size effect on strength, brittleness and fracture in brittle materials like concrete. The discrete element method (DEM) was used to simulate the size effect during quasi-static splitting tension with the experimental-based meso-structure. The two-dimensional (2D) calculations were carried out on concrete cylindrical specimens with two diameters wherein two different failure...
-
Influence of service ageing on polyester-reinforced polyvinyl chloride-coated fabrics reported through mathematical material models
PublicationIn this paper the coupled service (constructional tension) and environmental (sunlight, rainfalls, temperature variations) ageing influence on the polyester-reinforced polyvinyl chloride (PVC)-coated fabric VALMEX is studied. Two cases of the same fabric have been analyzed: one USED for 20 years on the real construction of the Forest Opera in Sopot (Poland), and one kept as a spare material (NOT USED). The following tests have...
-
Temper bead welding of S420G2+M steel in water environment
PublicationThe article presents the idea of the use of Temper Bead Welding (TBW) technique to improve the weldability of high strength steel at underwater wet welding conditions. Wet welding method with the use of covered electrodes is described. This work shows results of metallographic examinations and hardness measurements of samples of S420G2+M steel with weld beads performed under water. It has been shown that Temper Bead Welding technique...
-
Structure-Property Relationship and Multiple Processing Studies of Novel Bio-Based Thermoplastic Polyurethane Elastomers
PublicationCurrently, the growing demand for polymeric materials has led to an increased need to develop effective recycling methods. This study focuses on the multiple processing of bio-based thermoplastic polyurethane elastomers (bio-TPUs) as a sustainable approach for polymeric waste management through mechanical recycling. The main objective is to investigate the influence of two reprocessing cycles on selected properties of bio-TPUs....
-
Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
PublicationThe 9% Cr steels were developed for ultra-supercritical (USC) power plants to meet the requirements of high operating temperature and pressure. These steels are produced to operate at high temperatures where impact toughness is not a concern; however, it becomes important for the welded joints to have good impact toughness at room temperature for manufacturing. The present work investigates the effect of the post-weld heat treatment...
-
Influence of thermal effects on mechanical properties of PVDF-coated fabric
PublicationThis paper describes the method of laboratory tests necessary for identification of temperature influence on mechanical properties of polyvinylidene fluoride-coated polyester fabric often used for tensile structures. Two nonlinear model descriptions are investigated. The first one is based on the piece-wise linear relations between stress and strain and the second one on the Murnaghan model of solid behavior. This paper is proposed...
-
Efektywność skrępowania betonu w grubościennych słupach typu Concrete-Filled Steel Tube o przekroju kołowym
PublicationW słupach typu CFST w stanie granicznym dochodzi do zwiększenia wytrzymałości betonu rdzenia na skutek jego skrępowania. Zaistnienie tego zjawiska zależy od wielu czynników. Jednym z najważniejszych z nich jest sztywność obwodowa płaszcza stalowego. Jej wpływ na efektywność wzrostu wytrzymałości betonu rdzenia przebadano eksperymentalnie na grupie 48 grubościennych słupów CFST. Wykazano, że nadmierne zwiększanie grubości płaszcza...
-
A benchmark for particle shape dependence
PublicationParticle shape is a major parameter for the space-filling and strength properties of granular materials. For a systematic investigation of shape effect, a numerical benchmark test was set up within a collaborative group using different numerical methods and particles of various shape characteristics such as elongation, angularity and nonconvexity. Extensive 2D shear simulations were performed in this framework and the shear strength...
-
Particle shape dependence in 2D granular media
PublicationParticle shape is a key to the space-filling and strength properties of granular matter. We consider a shape parameter eta describing the degree of distortion from a perfectly spherical shape. Encompassing most specific shape characteristics such as elongation, angularity and non-convexity, eta is a low-order but generic parameter that we used in a numerical benchmark test for a systematic investigation of shape dependence in sheared...
-
Predicting Performance of Lightweight Concrete with Granulated Expanded Glass and Ash Aggregate by Means of Using Artificial Neural Networks
PublicationLightweight concrete (LWC) is a group of cement composites of the defined physical, mechanical, and chemical performance. The methods of designing the composition of LWC with the assumed density and compressive strength are used most commonly. The purpose of using LWC is the reduction of the structure’s weight, as well as the reduction of thermal conductivity index. The highest possible strength, durability and low thermal conductivity...
-
Properties of Old Concrete Built in the Former Leipziger Palace
PublicationThis research aims to determine the mechanical, chemical, and physical properties of old concrete used in the former Leipziger Palace in Wrocław, Poland. The cylindrical specimens were taken from the basement concrete walls using a concrete core borehole diamond drill machine. The determination of the durability and strength of old concrete was based on specified chosen properties of the old concrete obtained through the following...
-
Unprecedented Adhesive Performance of Propylene-Based Hydroxyl Functionalized Terpolymers
PublicationThe synthesis of hydroxyl functionalized propylene-based terpolymers and their performance as hot melt adhesives were investigated. The products comprise uniformly distributed butyl and 4-hydroxyl-butyl branches along the polypropylene backbone. Despite the low hydroxyl-functionality level of ≤ 0.5 mol%, hydroxyl functionalized terpolymers show formidable adhesion to aluminum and steel providing an adhesive strength exceeding 16...
-
Concrete mix design using machine learning
PublicationDesigning a concrete mix is a process of synthesizing many components, it is not a simple process and requires extensive technical knowledge. The design process itself focuses on obtaining the required strength of concrete. Very often designing a concrete mix takes into account the need to maintain the proper water-demand and frost-resistance features. The parameters that influence the concrete class most significantly are the...
-
Proceedings of the fib Symposium 2019: Concrete - Innovations in Materials, Design and Structures 2019
PublicationDesigning a concrete mix is a process of synthesizing many components, it is not a simple process and requires extensive technical knowledge. The design process itself focuses on obtaining the required strength of concrete. Very often designing a concrete mix takes into account the need to maintain the proper water-demand and frost-resistance features. The parameters that influence the concrete class most significantly are the...
-
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublicationThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
Structural and physico-mechanical properties of natural rubber/GTR composites devulcanized by microwaves: Influence of GTR source and irradiation time
PublicationGround tire rubber from car and truck was modified using microwave irradiation at variable time. The irradiated ground tire rubber was used as filler in composites based on natural rubber. The composites, with high content of ground tire rubber, were prepared using an internal batch mixer and subsequently cross-linked at 160℃. The influence of the ground tire rubber source (car/truck) and irradiation time on structure, physico-mechanical...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublicationThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
Edgewise Compressive Behavior of Composite Structural Insulated Panels with Magnesium Oxide Board Facings
PublicationEdgewise compression response of a composite structural insulated panel (CSIP) with magnesium oxide board facings was investigated. The discussed CSIP is a novel multifunctional sandwich panel introduced to the housing industry as a part of the wall, floor, and roof assemblies. The study aims to propose a computational tool for reliable prediction of failure modes of CSIPs subjected to concentric and eccentric axial loads. An advanced...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublicationIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Chemical, Physical, and Mechanical Properties of 95-Year-Old Concrete Built-In Arch Bridge
PublicationThis research aimed to determine the durability and strength of an old concrete built-in arch bridge based on selected mechanical, physical, and chemical properties of the concrete. The bridge was erected in 1925 and is located in Jagodnik (northern Poland). Cylindrical specimens were taken from the side ribs connected to the top plate using a concrete core borehole diamond drill machine. The properties of the old concrete were...
-
Dynamic fracture of brittle shells in a space-time adaptive isogeometric phase field framework
PublicationPhase field models for fracture prediction gained popularity as the formulation does not require the specification of ad-hoc criteria and no discontinuities are inserted in the body. This work focuses on dynamic crack evolution of brittle shell structures considering large deformations. The energy contributions from in-plane and out-of-plane deformations are separately split into tensile and compressive components and the resulting...
-
Termooksydacyjna i fotooksydacyjna degradacja pianek poliuretanowych
PublicationPrzeprowadzono ocenę efektywności działania wybranych środków przeciwstarzeniowych w sztywnych piankach poliuretanowych, otrzymywanych na drodze syntezy jednoetapowej. Ocenę tę oparto na pomia-rach zmian barwy oraz wytrzymałości mechanicznej zsyntezowanych materiałów. Na podstawie analizy uzyskanych wyników stwierdzono, iż dodatek 3% mieszaniny I rzędowego antyutleniacza fenolowego oraz benzotriazolowego absorbera UV znacząco zmniejsza...
-
Chemical and Mechanical Properties of 70-Year-Old Concrete
PublicationThe aim of this research is to determine the durability and strength of concrete continuous footing based on the chosen mechanical, physical, and chemical properties of the concrete. The presented investigations constitute some opinions from experts on the bearing capacity of concrete continuous footing and the possibilities of carrying additional loads and extended working life. The cylindrical specimens were taken from continuous...
-
Structure and performance properties of environmentally-friendly biocomposites based on poly(ɛ-caprolactone) modified with copper slag and shale drill cuttings wastes
PublicationThe potential application of two types of industrial wastes, drill cuttings (DC) and copper slag (CS), as silica-rich modifiers of poly(ɛ-caprolactone) (PCL) was investigated. Chemical structure and physical properties of DC and CS fillers were characterized using X-ray diffractometer, X-ray fluorescence spectroscopy, particle size and density measurements. PCL/DC and PCL/CS composites with a variable content of filler (5 to 50...
-
Analytical approach for membrane action in laterally-restrained reinforced concrete square slabs under uniformly distributed loads
PublicationLaterally-restrained reinforced concrete slabs can mobilise compressive membrane action and subsequent tensile membrane action under extreme loading conditions, thereby enhancing the load resistance under uniformly distributed loads. Previous analytical study focuses primarily on tensile membrane action in simply-supported slabs. This paper describes an analytical approach for membrane action in laterally-restrained square slabs....
-
Roller burnishing
PublicationThe paper shows the process of roller burnishing as a method of finishing machine components. Based on own research the author presents the effects of the roller burnishing process to increase the hardness and residual stress as well as the wear and fatigue strength of burnishing components.
-
The effect of numerical 2D and 3D FEM element modelling on strain and stress distributions at laser weld notches in steel sandwich type panels
PublicationLike other means of transport, merchant ships face the problem of increasing requirements concerning the environment protection, which, among other issues, implies the reduction of fuel consumption by the ship. Here, the conventional approach which consists in making use of higher strength steels to decrease the mass of the ship hull can be complemented by the use of new steel structures of sandwich panel type. However, the lack...