Filters
total: 2343
filtered: 1848
displaying 1000 best results Help
Search results for: ROAD FATALITY RATE
-
ANALYSIS OF THE INCREASE OF CONSTRUCTION COSTS IN URBAN REGENERATION PROJECTS
PublicationThe subject of this paper is the analysis and evaluation of the reasons for construction costs increases in urban regeneration projects. The analysis considers major refurbishments of real estates’, as well as heavy repair and modernization of the road system. For the period mentioned, the costs from works and expenditure schedules were compared with the costs of additional works, which shows the percentage cost increase in relation...
-
RESEARCH OF PARTIAL DISCHARGE IN THE LABORATORY CONSTRUCTE
PublicationNowadays in the Czech Republic begins implementation of new types of leadership system with insulated conductors nowadays. This system is used because of the use of conductors in difficulties to reach terrains and lower failure rate. The finding of specific faults is problem, because today's digital protection are not able to find it.
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublicationDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
Simulation of Direct-Sequence Spread Spectrum Data Transmission System for Reliable Underwater Acoustic Communications
PublicationUnderwater acoustic communication (UAC) system designers tend to transmit as much information as possible, per unit of time, at as low as possible error rate. It is a particularly difficult task in a shallow underwater channel in which the signal suffers from strong time dispersion due to multipath propagation and refraction phenomena. The direct-sequence spread spectrum technique (DSSS) applied successfully in the latest standards...
-
Effective yttrium based coating for steel interconnects of solid oxide cells: Corrosion evaluation in steam-hydrogen atmosphere
PublicationThis work describes manufacture, analysis and test of a new well conducting corrosion-protection coating that can be applied on steel types with high chromium content. Electrolytic deposition of yttrium salts is used to form thin (<100 nm) coatings on both flat steel sheets (material: Crofer 22 APU) and its properties are proven on woven wire-meshes (materials from two different sources: SUS316 and SUS316L). The oxide scale on...
-
On the Limiting Distribution of Lempel-Ziv’78 Redundancy for Memoryless Sources
PublicationWe study the Lempel-Ziv'78 algorithm and show that its (normalized) redundancy rate tends to a Gaussian distribution for memoryless sources. We accomplish it by extending findings from our 1995 paper, in particular, by presenting a new simplified proof of the central limit theorem (CLT) for the number of phrases in the LZ'78 algorithm. We first analyze the asymptotic behavior of the total path length in the associated digital search...
-
Bioactive core material for porous load-bearing implants
PublicationSo far state of knowledge on biodegradable materials is reviewed. Among a variety of investigated materials, those composed of polymers and ceramics may be considered as only candidates for a core material in porous titanium alloy. The collagen and chitosan among natural polymers, polyhydroxy acids among synthetic polymers, and hydroxyapatite and tricalcium phosphate among ceramics are proposed for further research. Three essential...
-
Determination of dryout localization using a five-equation model of annular flow for boiling in minichannels
PublicationDetailed studies have suggested that the critical heat flux in the form of dryout in minichannels occurs when the combined effects of entrainment, deposition, and evaporation of the film make the film flow rate go gradually and smoothly to zero. Most approaches so far used the mass balance equation for the liquid film with appropriate formulations for the rate of deposition and entrainment respectively. It must be acknowledged...
-
Using wearable device for biomedical signal acquisition and processing
PublicationIn this paper we present the research conducted on synchronous measurements of biosignals. The experiment was conducted to evaluate the possibility of estimating vital signs based on eye tracking. Method: The eGlasses platform was used for acquisition of ECG, respiration rate, eye and pupil movement and blood pressure. Data were acquired in three 5 min. intervals during which a subject was performing certain tasks. The signals...
-
The unstable thermoelectric effect in non-stoichiometric Cu2Se during the non-equilibrium phase transition
PublicationThe superionic α ↔ β phase transition in Cu1.96Se thermoelectric material is investigated by means of thermal analysis (DSC) and measurements of Seebeck coefficient and electrical conductivity. Results of the DSC measurements with 1–10 K/min heating and cooling rates show that the material is close to the equilibrium phase composition during the transformation. However, the kinetic limitation of the process exists, which is indicated...
-
Determination of the theoretical and actual working volume of a hydraulic motor
PublicationA new methodology of determination of the theoretical and actual working volume of a hydraulic motor based on the characteristics of the delivered flow rate into hydraulic motor vs. the rotational speed at a constant pressure drop in the working chambers is described in this paper. A new method of describing the delivered flow rate into a motor per one shaft revolution as a nonlinear function of the pressure drop in the motor working...
-
Effect of pine impregnation and feed speed on sound level and cutting power in wood sawing
PublicationThe sound levels along with the cutting power registered during the sawing process of the impregnated and non-impregnated pine wood at two feed speeds are shown and compared in this paper. Statistically significant differences in the acoustic signals occurred at the lower feed rate. The differences became smaller with an increase in the feed speed. In contrast to the sound signal, the differences...
-
Numerical Simulations for Transonic Flow in Control Valve
PublicationResults of numerical simulations for transonic flow in control valve are presented. The valve is the main part of an adaptive pneumatic shock absorber. Flow structure in the valve domain and the influence of the flow non-uniformity in the valve on a mass flow rate is investigated. Numerical simulation results are compared with experimental data.
-
Die neue Straßenbrücke in Toruń (Thorn) – Teil 2 – Nachweise
PublicationAls Fortsetzung von Teil 1, der über den Entwurf und den Bau der neuen, die Weichsel querenden Straßenbrücken in Toruń (deutsch: Thorn) berichtet, geht es im Folgenden um die theoretischen und experimentalen Nachweisen zum Montageprozess und zu Probebelastungen. Somit eine umfassende Beurteilung der beschriebenen , herausragenden Ingenieursleistung gegeben.
-
Analysis of the dynamic influences on the Lowland Gate in Gdańsk
PublicationThe Lowland Gate has been built in 1626. It is one of the best-preserved historical buildings in Gdansk. The structure is still of the city's infrastructural importance as through it goes a road connecting two districts. The Gate is now so neglected that it is hard to appreciate its value. The main purpose of the investigation carried out was to determine the harmfulness of the traffic on the structure as well as the reasons of...
-
Methods of Cyclist Training in Europe
PublicationThe following study aims to address the issue of cyclist training methodologies. Recent European bicycle accident statistics reveal a troubling upward trend. A potential solution to mitigate such incidents involves providing cyclists with comprehensive training encompassing traffic regulations and interactions with fellow road users. We conducted a comparative analysis of the cycling education approaches and cyclist training systems...
-
Application of principal component and hierarchical cluster analysis in classifying defects of trolleybuses
PublicationThe failure rate of vehicles is a relevant task, which is strictly connected with the reliability of transportation systems. Methods of data analysis allow us to find similarity and differences between failure rates of several parts of trolleybuses. This paper deals with the statistic of failure of trolleybuses from the municipal transport company of Gdynia (Poland).
-
Układ kompensacji wpływu wzniesienia oraz przyspieszenia w przyczepie do badania oporu toczenia
PublicationW artykule przedstawiono metodę pomiaru współczynnika oporu toczenia przy wykorzystaniu przyczepy opracowanej w Zakładzie Pojazdów na Politechnice Gdańskiej. Następnie omówiono opatentowany układ bezwładnościowy do korekcji wpływu wzniesienia oraz metodę korekcji wpływu przyspieszenia wzdłużnego. W dalszej części przedstawiono przykładowe wyniki obrazujące pomiar współczynnika CRR na wzniesieniu przy zmiennej prędkości.
-
Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites
PublicationHybrid aluminium metal matrix composites have the potential to replace single reinforced aluminium metal matrix composites due to improved properties. Moreover, tribological performance is critical for these composites, as they have extensive application areas, such as the automotive, aerospace, marine and defence industries. The present work aims to establish the tribological characteristics of Al7068/Si3N4/BN hybrid metal matrix...
-
UV-Vis-Induced Degradation of Phenol over Magnetic Photocatalysts Modified with Pt, Pd, Cu and Au Nanoparticles
PublicationThe combination of TiO2 photocatalyst and magnetic oxide nanoparticles enhances the separation and recoverable properties of nanosized TiO2 photocatalyst. Metal-modified (Me = Pd, Au, Pt, Cu) TiO2/SiO2@Fe3O4 nanocomposites were prepared by an ultrasonic-assisted sol-gel method. All prepared samples were characterized by X-ray powder diffraction (XRD) analysis, Brunauer-Emmett-Teller (BET) method, X-ray photoelectron spectroscopy...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublicationWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
Crystallization kinetics study of dynamically vulcanized PA6/NBR/HNTs nanocomposites by nonisothermal differential scanning calorimetry
PublicationInvestigation of crystallization behavior and kinetics of thermoplastic elastomer nanocomposites was the subject of limited works because of complexities associated with semiexperimental modeling of such phenomenon in a system containing components having completely different behavior in the molten state. Nonisothermal crystallization kinetics of dynamically vulcanized PA6/NBR/HNTs thermoplastic elastomer nanocomposites was mathematically...
-
DETERMINATION OF THE EFFECT OF ENVIRONMENTAL FACTORS ON THE CORROSION OF WATER DISTRIBUTION SYSTEM BASED ON ANALYSIS OF ON-LINE CORROSION MONITORING RESULTS
PublicationCorrosion of water distribution system is a significant issue causing problems with quality, safety and continuity of distribution. The changes of corrosion rates of the water distribution systems in Cracow made of carbon steel were investigated by analysis of online corrosion monitoring system results. Corrosion rates were determined using the linear polarization method. The impact of rain, temperatures, conductivity, dissolved...
-
Influence of water and mineral oil on the leaks in satellite motor commutation unit clearances
PublicationThe article describes the flow rates of mineral oil and water flowing, as working media, through the commutation unit of a hydraulic satellite motor. It is demonstrated that geometrical dimensions of commutation unit clearances change as a function of the machine shaft rotation angle. Methods for measuring the rate of this flow and the pressure in the working chamber are presented. The results of pressure measurements in the working...
-
Hydrogen degradation of pre-oxidized zirconium alloys
PublicationThe presence of the oxide layers on Zr alloys may retard or enhance the hydrogen entry and material degradation, depending on the layer features. This research has been aimed to determine the effects of pre-oxidation of the Zircaloy-2 alloy at a different temperature on hydrogen degradation. The specimens were oxidised in laboratory air at 350°C, 700°C, and 900°C. After, some samples were tensed at 10-5 strain rate and simultaneously...
-
Treatment of landfill leachate in a constructed free water surface wetland system over a decade – Identification of disturbance in process behaviour and removal of eutrophying substances and organic material
PublicationAn 8 ha free water surface wetland system in Örebro, Sweden, which has sediment traps followed by 10 ponds for treatment of landfill leachate in the methanogenic stage, was studied from 2003 to 2012. The wetland was irregularly loaded and the leachate characteristics showed high temporal and spatial variability, so Multivariate Statistical Process Control was chosen as the diagnostic tool for detecting anomalies prior to assessing...
-
Influence of Gd deposition on the oxidation behavior and electrical properties of a layered system consisting of Crofer 22 APU and MnCo2O4 spinel
PublicationIn the study, the surface of the Crofer 22APU ferritic steel was modified with gadolinium oxide nanoparticles and a protective-conducting layer consisting of the MnCo2O4 spinel. This system was studied in the context of application in IT-SOFC interconnects. Four types of samples were studied: unmodified steel, steel coated with a manganese-cobalt spinel layer, steel modified with gadolinium oxide nanoparticles, and a system consisting...
-
Direct reduction of pellets through hydrogen: Experimental and model behaviour
PublicationThis paper presents the hydrogen reduction behaviour of industrial pellets designed for the efficient hydrogen based direct reduction. The pellets were provided with very low non ferrous oxides percentage (0.52 of basicity index) and with the absence on TiO2 oxides. The pellets measured diameters in the range 1.14–1.72 cm and were characterized in terms of porosity, pores size, tortuosity and compression strength. The pellets were...
-
Ocena wzmocnienia podłoża metodą wymiany dynamicznej na podstawie próbnych obciążeń kolumn
PublicationAnaliza wykonanego wzmocnienia słabego podłoża gruntowego pod nasyp drogowy w technologii kolumn DR na przykładzie obwodnicy Brodnicy. Omówienie warunków geotechnicznych podłoża i zastosowanych rozwiązań. Analiza wsteczna na podstawie wyników próbnych obciążeń kolumn oraz pomiarów osiadań wzmocnionego podłoża całego obszaru. Porównanie uzyskanych wyników i wnioski.
-
Zastosowanie addytywów w separacji pianowej białek serwatkowych i białek mlecznych
PublicationZaproponowano proces separacji pianowej do wydzielania białek ze strumieni poprodukcyjnych przemysłu mleczarskiego Ponadto zaproponowano zastosowanie w separacji pianowej białek serwatkowych i mlecznych addytywów dopuszczonych ustawą do stosowania w żywności. Jako cel pracy przyjęto uzyskanie wyników uzasadniających wybór takich addytywów, które intensyfikują przebieg i polepszają wynik procesu separacji pianowej białek. W części...
-
TOTAL SHIP OPERABILITY – REVIEW, CONCEPT AND CRITERIA
PublicationThe ship operability can be understood and analysed in different manners, and its quality is described using different indexes by different authors. Practically, there is no general and widely accepted description of total ship operability in the literature, nor in the rules of classification societies, which would include both seakeeping and manoeuvrability characteristics of a ship, and simultaneously take into account all ship...
-
Systematics of intelligent transport systems services
PublicationRecent years have seen a more intensified deployment of Intelligent Transport Systems (ITS) in Polish cities. Work is also underway on the implementation of ITS on the national roads within the National Traffic Management System (KSZR). The research project RID-4D (part of Road Innovations), is designed to fill the gap, which is the lack of systematics of ITS services in Poland. The paper presents a proposal of ITS services systematics,...
-
Synergistic Effects of Bitumen Plasticization and Microwave Treatment on Short-Term Devulcanization of Ground Tire Rubber
PublicationGround tire rubber (GTR) was mechano-chemically modified with road bitumen 160/220 and subsequently treated using a microwave radiation. The combined impact of bitumen 160/220 content and microwave treatment on short-term devulcanization of GTR was studied by thermal camera, wavelength dispersive X-ray fluorescence spectrometry (WD-XRF), static headspace, and gas chromatography-mass spectrometry (SHS-GC-MS), thermogravimetric analysis...
-
Current Status, Barriers and Development Perspectives for Circular Bioeconomy in Polish South Baltic Area
PublicationThe following article presents the current legal situation in Poland as well as in the European Union. Data on biomass production in the Polish South Baltic area were analyzed, along with an indication of the key sectors for the development of bioeconomy. Presentation of the current state of biomass management was made and areas necessary for development were indicated to facilitate the sustainable management of biomass and waste...
-
Korozja w środowisku ropy naftowej. Czynniki i monitorowanie
PublicationPrzedstawiono analizy właściwości ropy naftowej z punktu widzenia zawartych w niej czynników korozyjnych oraz ich wpływu na korozję stali w trakcie procesu destylacji ropy naftowej. Krytycznej analizie poddane zostały możliwości oferowane przez współczesne techniki pomiarowe. Wskazano na istotność prowadzenia kompleksowego programu oceny ropy, monitorowania korozji oraz stosowania ochrony inhibitorowej w celu ochrony instalacji...
-
Awaria wiaduktu nad obwodnicą Trójmiasta
PublicationOpisano awarię wiaduktu drogowego spowodowaną uderzeniem ponadnormatywnego gabarytowo pojazdu. Zwrócono uwagę na skutki uderzenia, powodujące zniszczenie jednego z przęseł. Przedstawiono wyniki teoretycznych analiz statyczno-wytrzymałościowych wiaduktu w stanie awaryjnym oraz w fazach rozbiórki uszkodzonego przęsła. Omówiono sposób doraźnego zabezpieczenia obiektu, warunki dalszej eksploatacji oraz sposób naprawy.
-
The Transmission Protocol of Sensor Ad Hoc Networks
PublicationThis paper presents a secure protocol for a radio Ad Hoc sensor network. This network uses the TDMA multiple access method. The transmission rate on the radio channel is 57.6 kbps. The paper presents the construction of frames, types of packets and procedures for the authentication, assignment of time slots available to the node, releasing assigned slots and slots assignment conflict detection.
-
Reliable OFDM Data Transmission with Pilot Tones and Error-Correction Coding in Shallow Underwater Acoustic Channel
PublicationThe performance of Underwater Acoustic Communication (UAC) systems are strongly related to the specific propagation conditions of the underwater channel. Horizontal, shallow-water channels are characterised by extremely disadvantageous transmission properties, due to strong multipath propagation and refraction phenomena. The paper presents the results of communication tests performed during a shallow, inland-water experiment with...
-
Waste Tyres Pyrolysis for Obtaining Limonene
PublicationThis review deals with the technologies of limonene production from waste tyre pyrolysis. Thermal decomposition is attractive for tackling the waste tyre disposal problem, as it enables both: energy to be recovered and limonene to be obtained. This material management recycling of tyres is environmentally more beneficial than the burning of all valuable products, including limonene. Given this recoverability of materials from waste...
-
Effectiveness of various types of coating materials applied in reinforced concrete exposed to freeze–thaw cycles and chlorides
PublicationThis study assesses the durability of coated and uncoated concrete surfaces protected with four different coating materials: water-soluble (BW), solvent-based (BR), mineral (MI), and epoxy (EP). The durability assessment includes evaluating the absorption rate of water, pull-off adhesion strength, and coating material thickness. Concrete samples were subjected to immersion in regular water and a 7% urea solution, followed by...
-
Reactive deposition of TiNx layers in a DC-magnetron discharge
PublicationTiNx layers have been deposited in 'balanced mode' and 'unbalanced mode' of a reactive DC-magnetron plasma (carrier gas argon, reactive gas nitrogen) under different conditions. Discharge power and reactive gas flow have been varied. The layers have been examined by X-ray photoelectron spectroscopy (XPS), X-ray reflectometry (XR), and spectroscopic ellipsometry (SE). The results of the layer analyses were combined with plasma investigations...
-
A Method of MOS Evaluation for Video Based Services
PublicationThis paper deals with a method for QoE evaluation for the services transmitting large amount of data perceived by the end user in relatively short time periods, e.g. streaming video in mobile operator...
-
Preparation and characterization of Pt/Pd-modified titanium dioxidenanoparticles for visible light irradiation
PublicationSeries of Pt/Pd–TiO2photocatalysts were obtained using the sol–gel method. The Pt/Pd–TiO2nanocom-posites showed significant visible light photoactivity. X-ray diffraction, STEM microscopy, UV–visspectroscopy and BET characterization allowed to conclude that the photocatalysts at the best perfor-mance had the anatase structure, 91 m2/g specific surface area, Pt/Pd alloy structure and 1–4 nm particlesize. The photocatalytic activity...
-
Diagnostics of the tram track shape with the use of the global positioning satellite systems (GPS/Glonass) measurements with a 20 Hz frequency sampling
PublicationSatellite geodetic measurements used in the diagnosis of railway tracks require professional receivers and a very high frequency rate of data processing. It stems from a significant speed (10 km/h) kinematic measurements carried out during the passage of a measuring platform. The survey results (positions) of deformed railroad track have waveforms nature requiring additional processing methods and approximations. Due to the announcement...
-
Efficiency evaluation of graduation process in Australian public universities
PublicationFirst-year attrition and on-time graduation are key challenges for contemporary universities, which determine their efficiency. Based on the benefit of the doubt approach, this study reports the efficiency of the graduation process in 37 Australian public universities. The super-efficiency model extended by restrictions on virtual weights is used. The proposed model considers the attrition rate and the on-time graduation rate separately...
-
Beyond the helium buffer: 12C−2 rotational cooling in cold traps with H2 as a partner gas: interaction forces and quantum dynamics
Publicationabstract = { The scattering cross-sections and corresponding rate coefficients for rotationally inelastic collisions of $^{12}$C$_2$^-$ ($^2 \Sigma_g^+$) with H$_2$ ($^1 \Sigma_g^+$) are presented over a broad range of cold-trap temperatures. They have been calculated using quantum scattering theory that employs a new ab initio potential energy surface. The rate coefficients for the inelastic processes in the anionic partner are...
-
Analysis of the Accuracy of Pulse Estimation Using Smart Watches
PublicationThe purpose of this paper is to perform an analysis of the accuracy of the pulse estimation by comparing readings from a smartwatch with readings from medical devices. The study required writing applications that allow continuous pulse measurement. As a result, two applications were created for the smartwatch. The first one is dedicated to Android Wear devices, while the other one is compatible with Tizen watches. The next step...
-
Radar Signal Parameters Estimation Using Phase Accelerogram in the Time-Frequency Domain
PublicationRadar signal parameter estimation, in the context of the reconstruction of the received signal in a passive radar utilizing other radars as a source of illumination, is one of the fundamental steps in the signal processing chain in such a device. The task is also a crucial one in electronic reconnaissance systems, e.g. ELINT (Electronic Intelligence) systems. In order to obtain accurate results it is important to measure, estimate...
-
Influence of Selected Saccharides on the Precipitation of Calcium-Vaterite Mixtures by the CO2 Bubbling Method
PublicationCalcium carbonate is a compound existing in living organisms and produced for many biomedical applications. In this work, calcium carbonate was synthesized by a CO2 bubbling method using ammonia as a CO2 absorption promotor. Glucose, fructose, sucrose, and trehalose were added into the reaction mixture to modify characteristics of precipitated calcium carbonate particles. To determine the polymorphic form of produced calcium carbonate...
-
Modelization of Nutrient Removal Processes at a Large WWTP Using a Modified ASM2d Model
PublicationThe biodegradation of particulate substrates starts by a hydrolytic stage. Hydrolysis is a slow reaction and usually becomes the rate limiting step of the organic substrates biodegradation. The objective of this work was to evaluate a novel hydrolysis concept based on a modification of the activated sludge model (ASM2d) and to compare it with the original ASM2d model. The hydrolysis concept was developed in order to accurately...