Search
Filters
total: 361
filtered: 161
Search results for: PROPORTIONAL FLOW CONTROL VALVE
-
Sensorless Field Oriented Control of Five Phase Induction Motor with Third Harmonic Injection
PublicationIn this paper, a sensorless field oriented control system of five-phase induction machine with the 3rd harmonic rotor flux is presented. Two vector models, α1-β1 and α3-β3, were transformed into d1-q1, d3-q3 models oriented in rotating frames, which correspond to the 1st and 3rd harmonic plane respectively. The authors proposed the linearization of the model in d-q coordinate frames by introducing a new variable “x” which is proportional...
-
Research of hydrotronic variable displacement radial piston pump with electro -pneumatic control
PublicationThe paper presents the developed new electro-pneumatic control (pneumotronic) system for hydraulic fixed-displacement radial piston pump. Hydraulic fixed-displacement radial piston pump equipped with the proposed control system changes into hydrotronic variable-displacement radial piston pump. Pump flow rate control is realized by means of programmable logic controller, electro-pneumatic valves, pneumatic cylinders and a sensor.
-
Nonlinear Control of a Doubly Fed Generator Supplied by a Current Source Inverter
PublicationNowadays, wind turbines based on a doubly fed induction generator (DFIG) are a commonly used solution in the wind industry. The standard converter topology used in these systems is the voltage source inverter (VSI). The use of reverse-blocking insulated gate bipolar transistor (RB-IGBT) in the current source inverter topology (CSI), which is an alternative topology, opens new possibilities of control methods. This paper presents...
-
Zastosowanie addytywów w separacji pianowej białek serwatkowych i białek mlecznych
PublicationZaproponowano proces separacji pianowej do wydzielania białek ze strumieni poprodukcyjnych przemysłu mleczarskiego Ponadto zaproponowano zastosowanie w separacji pianowej białek serwatkowych i mlecznych addytywów dopuszczonych ustawą do stosowania w żywności. Jako cel pracy przyjęto uzyskanie wyników uzasadniających wybór takich addytywów, które intensyfikują przebieg i polepszają wynik procesu separacji pianowej białek. W części...
-
An Experimental Investigation of Pressure Wave Celerity During the Transient Slurry Flow
PublicationTransportation of slurries in pressure pipelines is an example of a complex flow due to specific parameters of transported medium. For practitioners, the economy of designing and maintenance is usually the most important factor. For this reason, most of hydrotransport installations are fairly simple; however, they become more vulnerable to negative effects of the transient flow which can occur in pressure pipelines. As the consequence,...
-
Dimensioning of vortex storm overflows
PublicationVortex flow control can be made as a rotational chamber, where the centrifugal force is a supporting factor. The paper presents a simplified, but experimentally verified, method of such device designing.
-
Parameter selection of an adaptive PI state observer for an induction motor
PublicationThe paper discusses problems connected with the parameters selection of the proportional-integral observer, designed for recon- struction of magnetic fluxes and angular speed of an induction motor. The selection is performed in several stages that are focused on different criteria. The first stage consists in selecting observer’s gains and provides desired dynamical properties, taking into consideration immunity to disturbances and...
-
Sensorless field oriented control for five-phase induction motors with third harmonic injection and fault insensitive feature
PublicationThe paper presents a solution for sensorless field oriented control (FOC) system for five-phase induction motors with improved rotor flux pattern. In order to obtain the advantages of a third harmonic injection with a quasi-trapezoidal flux shape, two vector models, α1–β1 and α3–β3, were transformed into d1– q1, d3– q3 rotating frames, which correlate to the 1st and 3rd harmonic plane respectively. A linearization approach of the...
-
Automatyzacja stacji uzdatniania wody
PublicationNiniejsza praca przedstawia projekt systemu automatyki stacji uzdatniania wody. Przedstawiono procesy technologiczne stosowane na automatyzowanej SUW, wymagania stawiane systemowi automatyki oraz opis zaprojektowanego systemu. Opisano także przeprowadzone podczas rozruchu systemu badania oraz ocenę ich wyników.The paper presents a project of a control system for a water treatment plant. The process flow of water treatment is shown...
-
PLC-based Implementation of Stochastic Optimization Method in the Form of Evolutionary Strategies for PID, LQR, and MPC Control
PublicationProgrammable logic controllers (PLCs) are usually equipped with only basic direct control algorithms like proportional-integral-derivative (PID). Modules included in engineering software running on a personal computer (PC) are usually used to tune controllers. In this article, an alternative approach is considered, i.e. the development of a stochastic optimizer based on the (μ,λ) evolution strategy (ES) in a PLC. For this purpose,...
-
Nodal models of Pressurized Water Reactor core for control purposes – A comparison study
PublicationThe paper focuses on the presentation and comparison of basic nodal and expanded multi-nodal models of the Pressurized Water Reactor (PWR) core, which includes neutron kinetics, heat transfer between fuel and coolant, and internal and external reactivity feedback processes. In the expanded multi-nodal model, the authors introduce a novel approach to the implementation of thermal power distribution phenomena into the multi-node...
-
Comparable analysis of PID controller settings in order to ensure reliable operation of active foil bearings
PublicationIn comparison to the traditional solutions, active bearings offer great operating flexibility, ensure better operating conditions over a wider range of rotational speeds and are safe to use. In order to ensure optimum bearing performance a bearing control system is used that adapts different geometries during device operation. The selection of optimal controller parameters requires the use of modern optimization methods that make...
-
Suppression of Supply Current Harmonics of 18-Pulse Diode Rectifier by Series Active Power Filter with LC Coupling
PublicationThe reported research aims at improving the quality of three-phase rectifier supply currents. An effective method consists of adding properly formed booster voltages to the fundamental supply voltages using a series active filter. In the proposed solution, the booster voltages are generated by three single-phase systems consisting of inverters, LC filters, and single-phase transformers. The application of LC couplings ensures low...
-
Trailing-Edge Separation Control of a NACA 0015 Airfoil Using Dielectric-Barrier-Discharge Plasma Actuators
PublicationThis paper presents a part of the works conducted in the Plasmaero European project (task 3.1), where the trailing-edge flow separation of a NACA 0015 airfoil has been controlled using four different dielectric barrier discharge (DBD) actuator types at three institutions across Europe. The results show that it is possible to enhance the aerodynamic performance of aircraft at speeds up to 40 m/s. Dielectric-barrier-discharge vortex...
-
Supervisory Control System for Adaptive Phase and Work Cycle Management of Sequencing Wastewater Treatment Plant
PublicationThe paper presents the design of the integrated control system applied to Sequencing Batch Reactor (SBR) in a biological Wastewater Treatment Plant (WWTP) in Swarzewo, which operates under activated sludge technology. Based on the real data records, ASM2d biological processes model and aeration system model, hierarchical control system for dissolved oxygen tracking and cycle management is designed. Internal Model Controller (IMC)...
-
Hybrid storage management system consisting of supercapacitors and AHI batteries
PublicationIn the article the hybrid storage, composed of Aqueous Hybrid Ion battery and supercapacitor was presented. The system was tested through simulation studies. The work also describes the construction and properties of the developed device meant to control the energy flow of the storage and a communication system for remote parameter supervision.
-
Influence of Holes Manufacture Technology on Perforated Plate Aerodynamics
PublicationTranspiration flow is a very important and still open subject in many technical applications. Perforated walls are useful for the purpose of “flow control”, as well as for the cooling of walls and blades (effusive cooling) in gas turbines. We are still not able to include large numbers of holes in the numerical calculations and therefore we need physical models. Problems are related also to the quality of the holes in perforated...
-
Neural Modelling of Steam Turbine Control Stage
PublicationThe paper describes possibility of steam turbine control stage neural model creation. It is of great importance because wider application of green energy causes severe conditions for control of energy generation systems operation Results of chosen steam turbine of 200 MW power measurements are applied as an example showing way of neural model creation. They serve as training and testing data of such neural model. Relatively simple...
-
A Numerical Model Study on Grasse River Ice Control Structures
PublicationIce jams in the Grasse River have caused the erosion of capping material designed to prevent the resurfacing of the bed sediment in the PCB-contaminated area. Two in-stream ice-control structures are proposed to avoid the jam-induced erosion of the capping material. These two ice-control options are a pier-type ice-control structure and a reconstruction of a small hydropower dam upstream of the capping site. A numerical model study...
-
comparison of circular and rectangular narrow esps with longitudinal wire electrode
PublicationDiesel engines emit fine particles, which are harmful to human and animal health. There are several methods for decrease particulate emission from a diesel engines, but up to now, these methods are not enough effective or very expensive. An electrostatic precipitation was proposed as an alternative method for control of a diesel particulate emission. Therefore, narrow electrostatic precipitators (ESPs) have become a subject of...
-
Stormwater runoff in the urbanized coastal basin of Gdańsk Urbanized basin of Gdańsk
PublicationAnthropopressure strongly affects the primal water cycle. Alternation of the natural basins imposes changes of drainage patterns, reduction of bioretention, infiltration and base flow. As a result the overland flow predominates and greater runoff rates flow into storm water collection systems and reservoirs. Moreover changing climatic conditions increase the frequency of rapid extreme weather events. Infrastructures of urban areas...
-
Quadrotor Flight Controller Design Using Classical Tools
PublicationA principal aspect of quadrocopter in-flight operation is to maintain the required attitude of the craft’s frame, which is done either automatically in the so-called supervised flight mode or manually during man-operated flight mode. This paper deals with the problem of flight controller (logical) structure and algorithm design dedicated for the man-operated flight mode. The role of the controller is to stabilise the rotational...
-
Investigation of Narrow Transverse and Longitudinal Electrostatic Precipitators
PublicationDiesel engines emit fine particles, which are harmful to human and animal health. There are several methods for decrease particulate emission from a diesel engines, but up to now, these methods are not enough effective or very expensive. An electrostatic precipitation was proposed as an alternative method for control of a diesel particulate emission. Therefore, narrow electrostatic precipitators (ESPs) have become a subject of...
-
Voltage and Reactive Power Load Flow Optimization in the Power System Using Fuzzy Logic
PublicationThe paper presents issues related to voltage control in the power system. An original method of reactive power flow optimization is considered, which leads to improved voltages in the power system and reduced active power losses. The optimization method is based on a procedure that employs fuzzy logic and is supported by a gradient search algorithm. The method has been implemented in PLANS software and verified.
-
Grid-Forming Operation of Energy-Router Based on Model Predictive Control with Improved Dynamic Performance
PublicationThe focus of this study is on the grid-forming operation of the Energy Router (ER) based on Model Predictive Control (MPC). ER is regarded as a key component of microgrids. It is a converter that interfaces the microgrid (s) with the utility grid. The ER has a multiport structure and bidirectional energy flow control. The ER concept can be implemented in Nearly Zero-Energy Buildings (NZEB) to provide flexible energy control. A...
-
Possibilities of radioisotope measuring in control of an unstable solid particles hydrotransport
PublicationThe paper presents γ-radiation proposal to control a multiphase flow, independently from circumstances. So this method may be applied even in compound industrial or environmental processes. Moreover in many cases, it is the only method for applications for dense mixture containing coarse angular grains. The constructed equipment allows continuous measurement of density as well as solid phase for both concentration and average velocity....
-
Diagnosing marine turbine engines through energy characteristics of their flow section
PublicationThe aim of the performed research was to develop of diagnostic method of the flow section of a marine turbine combustion engine based on the level of delamination of its energy characteristics. The here adopted diagnostic model provides for a formulation of the evaluation of the technical conditions based on the measurements of the parameters of the thermodynamic medium in the characteristic control cross-sections of the engine...
-
Exhaust gas temperature measurements in diagnostic examination of naval gas turbine engines. Part II. Unsteady processes
PublicationThe second part of the article presents the results of operating diagnostic tests of a two- and three-shaft engine with a separate power turbine during the start-up and acceleration of the rotor units. Attention was paid to key importance of the correctness of operation of the automatic engine load control system, the input for which, among other signals, is the rate of increase of the exhaust gas flow temperature. The article...
-
Modeling and simulation of tool cycle in manufacturing cell
PublicationThe paper addresses issues concerning modeling and analysis of tool flow within a three-machine manufacturing cell used for small batch manufacturing of a definite spectrum of prismatic parts. The approach utilizes a method for job and tool allocation to work centers with limited number of machines and capacity of tool resources, based on the analysis of formalized relations: job - tool sets required. Selected tool flow control...
-
Comparative analysis of seismic response reduction in multi-storey buildings equipped with base isolation and passive/active friction-tuned mass dampers
PublicationThis study presents an innovative approach to mitigating seismic responses in multi-storey buildings equipped with a base-isolation (BI) system and passive friction-tuned mass dampers (PFTMDs). The key innovation lies in the combined use of a BI system and a PFTMD system, as well as the activation of this mechanical system by controllers. Additionally, the research design optimizes the parameters of these devices specifically for...
-
Recent advances in hydrogen production from biomass waste with a focus on pyrolysis and gasification
PublicationThis paper presents the results research on the optimal fuel compositions and the control parameters of the spark ignition engine fueled with syngas-biogas-hydrogen for the purpose of setting up a flexible electronic control unit for the engine working in a solar-biomass hybrid renewable energy system. In syngas-biogas-hydrogen mixture, the optimal content of hydrogen and biogas is 20% and 30%, respectively. Exceeding these thresholds,...
-
Flexible syngas-biogas-hydrogen fueling spark-ignition engine behaviors with optimized fuel compositions and control parameters
PublicationThis paper presents the results research on the optimal fuel compositions and the control parameters of the spark ignition engine fueled with syngas-biogas-hydrogen for the purpose of setting up a flexible electronic control unit for the engine working in a solar-biomass hybrid renewable energy system. In syngas-biogas-hydrogen mixture, the optimal content of hydrogen and biogas is 20% and 30%, respectively. Exceeding these thresholds,...
-
Research on protection mechanisms of Resilient Packet Ring Network.
PublicationPaper describes iSteering - a new method to control traffic in case of RPR network failure. There's comparison of packet wrapping, steering and our proposed method iSteering, which can be used in case of transmitter/receiver or fiber failure. Numerical analysis for even and random traffic flow has been made in order to compare packet wrapping, steering and iSteering. The results of all the tests are included.
-
Rational method of grit chamber efficiency determination
PublicationAlthough grot chambers are designed with utmost care, they still remain difficuly to control. As concentration of grit is non-uniform, representative measurements of the sand concentration is a very complex issue. In the paper the results of measure,ents performed at WTP in Gdańsk and Gdynia were analyzed. The proposed method to determine grit chambers efficiency is based on comparison of suspension flow in the inlet and flux of...
-
THERMAL ANALYSIS AND DESIGN OF HYBRID MICROCHANNEL -MICROJET TEST PROBE
PublicationAccurate control of cooling parameters is required in ever wider range of technical applications. It is known that reducing the flow hydraulic diameter to an increase in the economy of cooling and improves its quality (Mikielewicz and Muszyński 2009). Present study describes research results related to the design and construction of the test stand for hybrid microjet- microchannel cooling modules study, which may be applied in...
-
MODEL FOR MEASUREMENT OF FLOW INSTALLATION TIME IN SDN SWITCH
PublicationSDN is the approach in telecommunication networks that separates control plane from data forwarding plane by specifying a single network entity as a controller that defines rules (called flows) of traffic forwarding for the switches connected to it. The time that is required for installation of these rules might be a hindrance for the overall performance of SDN network. In the paper, a model for testing and evaluating the influence...
-
A stochastic approach for the solution of single and multi – objective optimisation problems of biological processes in sequencing batch reactor
PublicationThis paper investigates the impact of implementing single and multi-optimisation solutions on the biological treatment process in a sequencing batch reactor (SBR). The research is based on a case study of the water resource recovery facility (WRRF) in Swarzewo, Northern Poland. The paper introduces the adaptive extremum seeking control (ESC) method for dissolved oxygen (DO) concentration control and places it in a layered control structure....
-
Proportional-Derivative and Model-based Controllers used for a Serial Type Manipulator in case of a Variable Mass Payload
PublicationIn the paper, numerical analysis of dynamics of a variable mass system is considered. Its reference example is a serial-like manipulator composed of revolute joints and rigid bodies. Payload of its gripper is considered as its variable mass element (mass and inertia irregularly between subsequent payloads). For the rest of the system, inertia parameters are considered as known (precisely identified during the assembling process)....
-
A system for acoustic field measurement employing cartesian robot
PublicationA system setup for measurements of acoustic field, together with the results of 3D visualisations of acoustic energy flow are presented in the paper. Spatial sampling of the field is performed by a Cartesian robot. Automatization of the measurement process is achieved with the use of a specialized control system. The method is based on measuring the sound pressure (scalar) and particle velocity (vector) quantities. The aim of the...
-
The logistics streamlining of the material flow at the production company
PublicationThe main practical problem in the Logistics Department at the company is overstaffing in the unit responsible for the flow of materials. Carried out by the authors of the article, some detailed research on the process analysis in the discussed company indicates that the main cause of such a situation is related to an increase in the amount of transported material and a lack of redesigning the material flow in...
-
ANALYSIS OF POSSIBILITIES FOR THE USE OF VOLUME-DELAY FUNCTIONS IN THE PLANNING MODULE OF THE TRISTAR SYSTEM
PublicationTravel time is a measure commonly used for traffic flow modelling and traffic control. It also helps to evaluate the quality of traffic control systems in urban areas. Traffic control systems that use traffic models to predict changes and disruptions in vehicle flows have to use vehicle speed-prediction models. Travel time estimation studies the effects of traffic volumes on a street section at an average speed. The TRISTAR Integrated...
-
Multi-DBD actuator with floating interelectrode for aerodynamic control
PublicationIn this paper the use of a floating inter-electrode in a multi-DBD (dielectric barrier discharge) plasma actuator is described. The multi-DBD plasma actuators with floating inter-electrodes were investigated to get a longer DBD on a dielectric surface and to maximise generated net airflow. Our actuator was used to control the boundary layer flow separation around NACA0012 airfoil model. The results of our investigations suggests...
-
Mathematical Models of Control Systems of Angular Speed of Steam Turbines for Diagnostic Tests of Automatic and Mechatronic Devices
PublicationAccurate modeling of physical processes of many automatics and mechatronics systems is often necessity. In power system such a process is control of angular velocity of power objects during connection to operation in parallel. This process is extremely dynamic. For this reason response of control system depends from changes of many physical parameters (temperature, pressure and flow of the medium, etc.). Precision modeling influences...
-
Experimental studies on the impact of changing the pipe material on the propagation of the pressure wave during water hammer
PublicationAim of the paper is to present the results studying the water hammer phenomenon in pipes made of different materials, and to show the impact of changing the type of material of the pipe on the velocity of the pressure wave during the transient flow in the pipes. In terms of research material and methods, pipes made of galvanized steel and high-density polyethylene were tested. Measurements were made using strain gauges with a high...
-
QoS Extensions for Flow-Awareness Networks
PublicationThe paper contains a description and research results of the proposal for distributed QoS extensions for Flow-Based Networking. These QoS extensions let the network accept or reject flows based on current network load and QoS promises for each of the flows. Proposed solution consists of two distributed components, each of them performing in every node, measurement system and access control. The solution could be applied in any...
-
Heterogeneity of national accounting systems, world-class universities and financial resources: What are the links?
PublicationThis study investigates the relationship between university financial resources, applied accounting systems, and the place of a university in the Shanghai Ranking. We find a strong relationship between the financial resources under the control of a world-class university and the position of that university in the highest tier of the global ranking. We propose a model (available online) to predict a university’s tier in the ranking...
-
Theoretical consideration of free convective heat transfer from a round isothermal plate slightly inclined from the vertical
PublicationA semi-analytical solution of simplified Navier-Stokes and Fourier-Kirchhoff equations describing free convective heat transfer from a round isothermal surface slightly inclined from the vertical is presented. The solution is based on the assumption, typical for natural convection, that the velocity component normal to the surface is negligibly small in comparison to the tangential one. Next we neglect the nonlinear inertia force...
-
Electrochemical Production of Sodium Hypochlorite from Salty Wastewater Using a Flow-by Porous Graphite Electrode
PublicationThe production of sodium hypochlorite (NaOCl) from salty wastewater using an electrochemical cell has several advantages over other methods that often require hazardous chemicals and generate toxic waste, being more sustainable and environmentally friendly. However, the process of producing sodium hypochlorite using an electrochemical cell requires careful control of the operating conditions, such as the current density, flow rate,...
-
Investigation of Narrow Electrostatic Precipitator with Wire Multi-Electrode
PublicationDiesel engines emit fine particles, which are harmful to human and animal health. There are several methods for decrease particulate emission from a diesel engines, but up to now, these methods are notenough effective or very expensive. An electrostatic precipitation was proposed as an alternative method for control of a diesel particulate emission. Therefore, narrow electrostatic precipitators (ESPs) have become a subject of interest...
-
Human-computer interactions in speech therapy using a blowing interface
PublicationIn this paper we present a new human-computer interface for the quantitative measurement of blowing activities. The interface can measure the air flow and air pressure during the blowing activity. The measured values are stored and used to control the state of the graphical objects in the graphical user interface. In speech therapy children will find easier to play attractive therapeutic games than to perform repetitive and tedious,...