Search
Filters
total: 2649
filtered: 2189
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: underground power cables
-
Two-phase optimizing approach to design assessments of long distance heat transportation for CHP systems
PublicationCogeneration or Combined Heat and Power (CHP) for power plants is a method of putting to use waste heat which would be otherwise released to the environment. This allows the increase in thermodynamic efficiency of the plant and can be a source of environmental friendly heat for District Heating (DH). In the paper CHP for Nuclear Power Plant (NPP) is analyzed with the focus on heat transportation. A method for effectivity and feasibility...
-
Tesla Friction-Type Micro Turbine For Small-Scale Cogeneration
PublicationTesla turbine is rarely used in professional power installations due to its specific work characteristics and relatively low internal efficiency. However, it has some potential to be applied in micro-power plants operating in distributed co-generation systems, also working in an organic Rankine cycle. This paper presents results from numerical calculations of flow in three models of Tesla disk turbines assuming nitrogen as a working...
-
Cutting model parameters from frame sawing of natural and impregnated Scots pine (Pinus sylvestris L.)
PublicationIn this paper, absolute and density normalized cutting model parameters of natural and impregnated Scots pine (Pinus sylvestris L.) are shown and a method for the calculation of their corresponding material properties in the principal material directions of wood is presented. The parameters were determined from measurements of cutting power on a sash gang saw, and are in detail the fracture toughness and the shear yield strength...
-
Investigation of the Combustion Processes in the Gas Turbine Module of an FPSO Operating on Associated Gas Conversion Products
PublicationIn this paper, we consider the issue of thermo-chemical heat recovery of waste heat from gas turbine engines for the steam conversion of associated gas for offshore vessels. Current trends in the development of offshore infrastructure are identified, and the composition of power plants for mobile offshore drilling units and FPSO vessels is analyzed. We present the results of a comparison of power-to-volume ratio, power-to-weight...
-
Towards an efficient multi-stage Riemann solver for nuclear physics simulations
PublicationRelativistic numerical hydrodynamics is an important tool in high energy nuclear science. However, such simulations are extremely demanding in terms of computing power. This paper focuses on improving the speed of solving the Riemann problem with the MUSTA-FORCE algorithm by employing the CUDA parallel programming model. We also propose a new approach to 3D finite difference algorithms, which employ a GPU that uses surface memory....
-
Metrological analysis of an computerized system of protection against electric shock in circuits with variable speed drives
PublicationDrive systems, that can be operated at variable speed, are equipped with power electronics converters. This causes distortion of the earth current, and consequently the need to take into account the use of proper protective devices in relation to earth current harmonics. This paper presents a system for protection against electric shock in circuits with power electronics converters and metrological analysis indicating the requirements...
-
Simulation Studies of Control Systems for Doubly Fed Induction Generator Supplied by the Current Source Converter
PublicationThe control system for a Doubly Fed Induction Generator (DFIG) supplied by a grid-connected Current Source Converter (CSC) is presented in this paper. Nonlinear transformation of DFIG model to the multi-scalar form is proposed. The nonlinear control strategy of active and reactive power of DFIG is realized by feedback linearization. In the proposed control scheme, the DFIG model and CSI parameters are included. Two Proportional-Integral...
-
Attempt to a Video-Transmission Capability in MV Mine Cable Network Using BPL-PLC Technology
PublicationThis article presents and discusses the attempt to transmit video content using the BPL-PLC (Broadband over Power Line - Power Line Communication) technology. It includes simulation results of a specially developed digital transmitter and receiver, dedicated to a given predefined 6 kV mining power cable. The effect of two different transmission modes (2-7 MHz and 3-7.5 MHz) and two types of coupling (capacitive-inductive and induction-inductive),...
-
SHEAR YIELD STRESSES AND FRACTURE TOUGHNESS OF SCOTS PINE (PINUS SYLVESTRIS L.) ACCORDING TO THE RAW MATERIAL PROVENANCE
PublicationIn this paper values of the fracture toughness and of shear yield stress in the shear zone of Scots pine are presented. Tests of cutting were carried on samples of Scotch pine (Pinus sylvestris L.) wood of five provenances from Poland. These experimentally cutting tests were carried on the sash gang saw PRW-15M and the values of cutting power were obtained. The values of fracture toughness and shear yield stress based on Atkins’s...
-
The Effect of Wood Provenance and Density on Cutting Forces While Sawing Scots Pine (Pinus sylvestris L.)
PublicationSeveral properties of wood including the cutting power requirements can be correlated to wood density. Therefore, according to the literature, the cutting power requirements (and/or cutting forces) could be computed as a function of the wood specific gravity. This research shows that such an approach, based solely on specific gravity, may be considered a rather rough and imperfect estimate of cutting power. Samples of Scots pine...
-
Arylated carbon nanotubes for biobatteries and biofuel cells
PublicationSinglwalled carbon nanotubes (swcnts)covalently phenylated, napthylated or terphenylated were used for the construction of cathodes in a biobattery and in a biofuel cell. zn is the anode in the biobaterry and single-walled carbon nanotubes are covalently modified with glucose oxidase/catalase (swcnt-gox/cat) and the biofuel cell anode. the cell parameters were determined and the potentials of each of the electrodes under cell working...
-
Solid Oxide Fuel Cells with Ni infiltrated perovskite anode
PublicationNiobium-doped strontium titanate was used as the anode for a solid oxide fuel cell. Electrolyte-supported cells were prepared with pure perovskite and composite perovskite–yttria–stabilized-zirconia (YSZ) anodes. Fuel cell tests demonstrated significant improvement in power density after infiltration with a small amount of Ni. The obtained values of power densities are comparable with conventional Ni/YSZ cermet anode. In addition,...
-
Measurement and Analysis of the Radio Wave Polarisation in Off-Body Communications in Indoor Environment
PublicationThe paper describes an analysis of the radio wave polarisation in off-body communications in indoor environment. The measurement stand for polarisation measurements has been shortly described. Five investigated scenarios with different body postures and different antenna placements have been characterize. The vertical and horizontal components of received radio signal have been analysed. The measure used in analysis is a ratio...
-
Behavioral state classification in epileptic brain using intracranial electrophysiology
PublicationOBJECTIVE: Automated behavioral state classification can benefit next generation implantable epilepsy devices. In this study we explored the feasibility of automated awake (AW) and slow wave sleep (SWS) classification using wide bandwidth intracranial EEG (iEEG) in patients undergoing evaluation for epilepsy surgery. APPROACH: Data from seven patients (age [Formula: see text], 4 women) who underwent intracranial depth electrode...
-
Independent dynamics of low, intermediate, and high frequency spectral intracranial EEG activities during human memory formation
PublicationA wide spectrum of brain rhythms are engaged throughout the human cortex in cognitive functions. How the rhythms of various frequency ranges are coordinated across the space of the human cortex and time of memory processing is inconclusive. They can either be coordinated together across the frequency spectrum at the same cortical site and time or induced independently in particular bands. We used a large dataset of human intracranial...
-
A Development of a Capacitive Voltage Divider for High Voltage Measurement as Part of a Combined Current and Voltage Sensor
PublicationThis article deals with the development of capacitive voltage divider for high voltage measurements and presents a method of analysis and optimization of its parameters. This divider is a part of a combined voltage and current sensor for measurements in high voltage power networks. The sensor allows continuous monitoring of the network distribution status and performs a quick diagnosis and location of possible network failures....
-
Koncepcja zdalnego sterowania i monitoringu urządzeń trakcyjnych z wykorzystaniem technologii teleinformatycznych
PublicationAdvancement in wireless communication enables engineers to apply sophisticated and relatively inexpensive technologies in new fields of industry, which were previously designated solely to wire-based solutions. One of those fields is railway transportation system. In effect of a high reliability and safety demands, this area was resistive to new technologies. Nowadays, increased security and reliability of wireless sensor networks...
-
Application of fracture mechanics for energetic effects predictions while wood sawing
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (power) could be considered from a point of view of modern fracture mechanics. Cutting forces may be employed to determine not only toughness...
-
Nowoczesne metody termochemicznej konwersji biomasy w paliwa gazowe, ciekłe i stałe = Modern methods of thermochemical biomass conversion into gas, liquid and solid fuels
PublicationBiomass utilization through direct- or co-combustion with coal, based on coal, hydrogen and oxygen compounds chemical energy conversion into heat in boilers, is simultaneously the cheapest and - according to experts - economically least effective solution. In case of heat and electricity production in cogeneration process in biomass fueled heat and power stations (wood, straw, energetic plants, RDF etc), investment costs are little...
-
Performance Evaluation of Selected Parallel Object Detection and Tracking Algorithms on an Embedded GPU Platform
PublicationPerformance evaluation of selected complex video processing algorithms, implemented on a parallel, embedded GPU platform Tegra X1, is presented. Three algorithms were chosen for evaluation: a GMM-based object detection algorithm, a particle filter tracking algorithm and an optical flow based algorithm devoted to people counting in a crowd flow. The choice of these algorithms was based on their computational complexity and parallel...
-
Synchronous generator model taking into account the non-uniform saturation of the pole shoes
PublicationFor the evaluation of modern electric power systems with regard to their behavior, weight, and reliability a novel modeling and simulation tools have been developed. The paper presents circuit model of synchronous generator taking into account both the non-sinusoidal distribution of the stator and rotor winding, and non-uniform saturation of the pole shoes. This model is suitable for simulation of both salient and no-salient pole...
-
Revisiting Toroidal Dipolar Moment in Planar Metamaterial
PublicationThis article revisits the electric, magnetic, and toroidal dipolar moments in the metamaterial structure and presents the flatland design for generating a toroidal dipolar response for the electromagnetic plane wave at normal incidence. Based on the numerical analysis of the surface current, the electric field, the magnetic field, and the quantitative analysis of scattered power supported by the electromagnetic multipole theory,...
-
Towards hand grip force assessment by using EMG estimators
PublicationThe purpose of this study was to propose a method to assess individual regression (calibration) curves to establish a relationship between an isometric grip force and surface electromyography (EMG) estimator. In this study 18 healthy volunteers (12 male (23.0 ± 2.0 years) and 6 female (23.2 ± 0.7 years)) had been examined. Ten EMG estimators (mean absolute value, root mean square, entropy, energy, turns per second, mean of zero...
-
On the independence number of some strong products of cycle-powers
PublicationIn the paper we give some theoretical and computational results on the third strong power of cycle-powers, for example, we have found the independence numbers alpha((C^2_10)^⊠3) = 30 and alpha((C^4 _14)^⊠3) = 14. A number of optimizations have been introduced to improve the running time of our exhaustive algorithm used to establish the independence number of the third strong power of cycle-powers. Moreover, our results establish...
-
Intelligent turbogenerator controller based on artifical neural network
PublicationThe paper presents a desing of an intelligent controller based on neural network (ICNN). The ICNN ensures at the same time two fundamental functions : the maintaining of generator voltage at the desired value and the damping of the electromechanical oscillations. Its performance is evaluted on a single machine infinite bus power system through computer simulations. The dynamic and transient operation of the proposed controller...
-
CMOS realisation of analogue processor for early vision processing
PublicationThe architecture concept of a high-speed low-power analogue vision chip, which performs low-level real-time image algorithms ispresented. The proof-of-concept prototype vision chip containing 32 × 32 photosensor array and 32 analogue processors is fabricated usinga 0.35 μm CMOS technology. The prototype can be configured to register and process images with very high speed, reaching 2000 framesper second, or achieve very low power...
-
Modal Analysis of Planar Elliptical Resonator Deposited on Unshielded Dielectric Slab
PublicationModal analysis of isolated open planar elliptical patch placed on dielectric slab is presented in the paper. It applies concept of Illuminating Modes which is formulated for the case of two-side opened structure. The current on patch is expanded in basis functions in form of Mathieu radial and angular functions. The spectrum of excited modes for exemplary planar resonators is presented and discussed using the concept of power of...
-
Efficiency of Biomass Energy used for Heating Purposes in a Residential Building in Comparison with other Energy Sources
PublicationThis paper discusses the results of analyses investigating the energy efficiency of biomass in comparison with other popular energy carriers used for heating, ventilation and water heating in residential buildings. The compared energy sources were lignite, natural gas, heating oil and electricity produced by conventional and integrated power generation plants. The most efficient variant relying on biomass and the least efficient...
-
FORECASTING BIOGAS FORMATION IN LANDFILLS
Publication: The aim of the present research was to develop a mathematical model for estimating the amount of viscous gas generated as a function of weather conditions. Due to the lack of models for predicting gas formation caused by sudden changes in weather conditions in the literature, such a model was developed in this study using the parameters of landfills recorded for over a year. The effect of temperature on landfill gas production...
-
Review of Small Gas Turbine Engines and Their Adaptation for Automotive Waste Heat Recovery Systems
Publication -
A Five-Leg Three-Level Dual-Output Inverter
PublicationClassical 3-level dual-output inverter, 3-L DOI, involves two similar 3-level inverters that provides a pair of 3-phase output voltages with same or different frequencies from common input voltage source. Flexibility of either operation of the constituting inverters is evident in this DOI; but total duplication of power switches is a major drawback. State of the art coupled 3-L DOIs reduce this drawback by providing series-shared...
-
Subcritical Thermodynamic Cycles with Organic Medium and Isothermal Expansion
PublicationThe efffciencies of the Organic Rankine Cycle (ORC) are not very high and only very seldom do they exceed 20%. The increase and optimization of initial parameters and certain modifications of the thermodynamic cycle make it possible to overcome these drawbacks. A new modified cycle has been described and analyzed in detail in the paper. Similarly to the Ericsson cycle for gas turbines, isothermal expansion in the turbine is suggested...
-
Open extensive IoT research and measurement infrastructure for remote collection and automatic analysis of environmental data.
PublicationInternet of Things devices that send small amounts of data do not need high bit rates as it is the range that is more crucial for them. The use of popular, unlicensed 2.4 GHz and 5 GHz bands is fairly legally enforced (transmission power above power limits cannot be increased). In addition, waves of this length are very diffiult to propagate under field conditions (e.g. in urban areas). The market response to these needs are the...
-
Human verbal memory encoding is hierarchically distributed in a continuous processing stream
PublicationProcessing of memory is supported by coordinated activity in a network of sensory, association, and motor brain regions. It remains a major challenge to determine where memory is encoded for later retrieval. Here we used direct intracranial brain recordings from epilepsy patients performing free recall tasks to determine the temporal pattern and anatomical distribution of verbal memory encoding across the entire human cortex. High...
-
Compensation Topologies in IPT Systems: Standards, Requirements, Classification, Analysis, Comparison and Application
PublicationWireless power transfer devices are becoming more relevant and widespread. Therefore, an article is devoted to a review, analysis and comparison of compensation topologies for an inductive power transfer. A new classification of topologies is developed. A lot of attention is paid to the problems of the physical fundamentals of compensation work, standards, safety, and five main topology requirements. It is determined, that topologies...
-
Organic Rankine cycle as bottoming cycle to a combined Brayton and Clausius - Rankine cycle
PublicationA preliminary evaluation has been made of a possibility of bottoming of a conventional Brayton cycle cooperating with the CHP power plant with the organic Rankine cycle installation. Such solution contributes to the possibility of annual operation of that power plant, except of operation only in periods when there is a demand for the heat. Additional benefit would be the fact that an optimized backpressure steam cycle has the advantage...
-
Study of the Operation of Synchronous Generator Voltage Regulator During the Creation of Post Blackout Start-up Path
PublicationThis paper presents the influence of automatic voltage regulator (AVR) of synchronous generator on the process of creation of post black-out start-up path. Two elements of AVR have a significant impact on this process: underexcitation limiter (UEL) and load compensation (LC). The authors present a theoretical investigation and simulation results that illustrate how the mentioned elements of AVR affect voltage levels in a power...
-
Distinctive properties of Scots pine (Pinus sylvestris L.) originating from the Carpathian and Great Poland-Pomeranian of Nature and Forest Land
PublicationIn this paper values of properties of Scots pine, the fracture toughness and of shear yield stress in the shear zone are presented. Samples of Scotch pine (Pinus sylvestris L.) wood of two provenances from Poland were tested. These properties were determined from the values of cutting power obtained experimentally on the saw frame PRW-15M. The values of fracture toughness and shear yield stress based on the Atkins model for cutting...
-
Small Vessel with Inboard Engine Retrofitting Concepts; Real Boat Tests, Laboratory Hybrid Drive Tests and Theoretical Studies
PublicationThe development of modern technologies and their increasing availability, as well as the falling costs of highly ecient propulsion systems and power sources, have resulted in electric or hybrid propulsions systems’ growing popularity for use on watercraft. Presented in the paper are design and lab tests of a prototype parallel hybrid propulsion system. It describes a concept of retrofitting a conventionally powered nine meter-long...
-
Performance of the PVT solar collector operated with water-Al2O3 nanofluid
PublicationAn experimental investigation of the hybrid module photovoltaic panel -solar collector (PVT) cooled by water-Al2O3 nanofluids has been conducted. The weight fractions of the nanoparticles were 1% and 3%. Thermal efficiency, power efficiency and overall efficiency have been determined for artificial source of light and sunlight. No noticeable effect of the nanoparticle concentration on the overall efficiency of the PVT module has...
-
PERFORMANCE OF THE PVT SOLAR COLLECTOR OPERATED WITH WATER –AL2O3 NANOFLUID
PublicationAn experimental investigation of the hybrid module photovoltaic panel -solar collector (PVT) cooled by water-Al2O3 nanofluids has been conducted. The weight fractions of the nanoparticles were 1% and 3%. Thermal efficiency, power efficiency and overall efficiency have been determined for artificial source of light and sunlight. No noticeable effect of the nanoparticle concentration on the overall efficiency of the PVT module has...
-
Application of Fracture Mechanics for Energetic Effects Predictions While Wood Sawing
PublicationIn the classical approach, energetic effects (cutting forces and cutting power) of wood sawing process are generally calculated on the basis of the specific cutting resistance, which is in the case of wood cutting the function of more or less important factors. On the other hand, cutting forces (or power - more interesting from energetic point of view) could be considered from a point of view of modern fracture mechanics. Cutting...
-
Przekształtnik prądu jako sterownik w układach napędowych z silnikami indukcyjnymi
PublicationThe circuits used for power conversion applied in drives with electric machines are classified into two groups: voltage source inverters (VSI) and current source inverters (CSI). Application of the current source inverter results in better properties of drive than application of voltage source inverter because there is no output filter. The development of power electronics and especially the IGBTs, in which on/off-times are very...
-
Damage detection in a bolted lap joint using guided waves
PublicationThe paper presents the experimental investigation of guided waves application to the condition assessment of prestressed bolted connections and a concept of new quantitative indicator. The main goal of the research was the analysis of the influence of the contact conditions changes to the characteristics of a propagating disturbance. The experimental tests were carried out for a single bolted lap joint. The excitation and acquisition...
-
Looking for a minimum exergy destruction in hierarchical cycle
PublicationThe paper presents results of energy analysis, complemented with an exergy balance, of hierarchical thermodynamic cycle. Proposed cycle is a binary vapour cycle based on a model of real supercritical steam power plant. Energy analysis is used to preliminary optimization of the cycle and the exergy losses analysis is proposed to perform optimization of heat transfer processes, which are essential for hierarchical cycles. Proposed...
-
Modelling of the Polish Electricity Generation Subsystem in MARKAL Program with Emphasis on the EU Emissions Trading Scheme
PublicationThis paper addresses issues related to greenhouse gas emissions in the European Union and measures to reduce them, in particular the European Emissions Trading Scheme (EU ETS). A model of the Polish electricity generation subsystem, taking into account EU ETS mechanisms, has been developed using the MARKAL optimization package. Data collected on the basis of available projects, regulations and statistics were entered into the model....
-
Evaluati on of long-term start up costs impact on short-term price based operational optimization of a CCGT using MILP
PublicationAn increasing share of the weather-dependent RES generation in the power system leads to the growing importance of flexibility of conventional power plants. They were usually designed for base load operation and it is a challenge to determine the actual long-term cycling costs, which account for an increase in maintenance and overhaul expenditures, increased forced outage rates and shortened life expectancy of the plant and components....
-
Experimental test results of an automatic voltage regulator with independent phase voltage controllers
PublicationThe growing number of distributed renewable energy sources and dynamic constant-power loads (e.g. electric vehicle charging stations) pose new challenges for network operators. These changes result in alterations to network load profiles and load flows, leading to greater voltage volatility. One effective solution to these problems can be the use of automatic voltage regulators (AVRs), which stabilize and symmetrize voltage output,...
-
Spatial variability of the hydrochemistry of shallow groundwaters and surface waters of the Rensdyrbekken: A case study of a permafrost catchment in Bellsund (SW Spitsbergen, Svalbard)
PublicationProgressive climate change may have unpredictable consequences for the Arctic environment. Permafrost catchments off the west coast of Svalbard, described as “thin” and “warm,” are particularly sensitive to climate change. The interdisciplinary research on the hydrochemical response of surface and underground water functioning within a small permafrost catchment area focused on the determination of the impact of meteorological...
-
Ancillary services to grids provided with distributed generation
PublicationThe paper introduces system for utilization of the customer-side generated energy. Additionally system can secure some ancillary services to grids. Those services include: current active filtering, load voltage stabilization and in case of grid voltage faults - uninterruptible load supplying (possible with energy storage device). Presented experimental results confirm flexibility of this arrangement in processes of power delivery...