Search
Filters
total: 851
filtered: 703
Search results for: steel structure
-
Mechanical and Microstructural Characterization of TIG Welded Dissimilar Joints between 304L Austenitic Stainless Steel and Incoloy 800HT Nickel Alloy
PublicationIn this article, the mechanical properties and microstructure of 304L austenitic stainless steel/Incoloy 800HT nickel alloy dissimilar welded joints are investigated. The joints were made of 21.3 mm × 7.47 mm tubes using the TIG process with the use of S Ni 6082 nickel filler metal. No welding imperfections were found and high strength properties of joints were obtained, meeting the assumed acceptance criteria of the product’s...
-
Study on deformed steel columns subjected to impact load due to soft-storey failure in buildings during earthquakes
PublicationThe so called soft-storey failure is one of the most typical types of damage induced in buildings as the result of earthquake excitation. It has been observed during ground motions that the failure of an upper soft storey of a structure results in large vertical impact load acting on the lower floors. If the resistance of the structural members of the lower storeys is not sufficient it may further lead to progressive collapse of...
-
FEM simulations applied to the failure analysis of RC structure under the influence of municipal sewage pressure
PublicationThe paper discusses a failure mechanism of reinforced concrete (RC) structure with steel cover that failed under the influence of municipal sewage pressure. To explain the reasons of failure, in-situ measurements, laboratory experiments and comprehensive Finite Element Method (FEM) computations were performed. Non-destructive in-situ scanning tests were carried out to determine quantity and cover thickness of embedded reinforcement...
-
"Raport z wstępnych badań własności stali trudnościeralnej 460HB",. ang "Report on preliminary tests of the properties of wear-resistant steel 460HB"
PublicationMikrostrukturę badanej stali trudnościeralnej 460HB stanowi drobnoziarnisty martenzyt odpuszczony, który jest właściwy dla stali konstrukcyjnych niskowęglowych, niskostopowych ulepszonych cieplnie. W przypadku blach grubych, do których zalicza się badana stal, struktura może ulec zaburzeniu, jeżeli w hutniczym procesie wytwórczym wystąpiła niejednorodność odkształcenia plastycznego i w konsekwencji tworzenie się pasm segregacyjnych,...
-
Corrosion Resistance and Structure of Cr−O−N Coatings Formed in Vacuum Arc Plasma Fluxes With PIIID
PublicationCr−O−N-based vacuum arc coatings are very promising for the wear and corrosion protection of various steel parts. The aim of the work was to determine the effect of frequency and amplitude of the pulsed bias voltage (UB) on the elemental and phase composition, mechanical, and corrosion properties of Cr−O−N coatings. They have an amorphous structure with embedded nanosized solid solution crystallites based on CrN with a cubic structure...
-
Analysis of EN 1993-1-6 guidelines about determining amplitudes of equivalent imperfections of steel cylindrical shells subjected to uniform external pressure
PublicationCivil engineering structures should be designed with reference to relevant standards. One of them is a Eurocode 3 standard EN 1993-1-6:2007: Design of steel structures Part 1-6: Strength and Stability of Shell Structures. According to this standard, the value of buckling load can be determined using different approaches: classical hand calculations (stress design) and geometrical and material non-linear analysis of an imperfect...
-
SHM System of the Roof Structure of Sports Arena “Olivia”
PublicationThe paper presents a structural health monitoring system of the Sports Arena “Olivia” in Gdansk, Poland. The system was installed because of doubts about the roof stability due to observed buckling of the steel truss members. The SHM system was based on nonlinear FEM models used for detection of type of near failure modes of the roof. The application of detailed FEM model in current state updated on data from in situ loading testes...
-
The abrasive wear resistance of coatings manufactured on high-strength low-alloy (HSLA) offshore steel in wet welding conditions
PublicationSome marine and offshore structure elements exploited in the water cannot be brought to the surface of the water as this will generate high costs, and for this reason, they require in-situ repairs. One of the repair techniques used in underwater pad welding conditions is a wet welding method. This paper presents an investigation of the abrasive wear resistance of coatings made in wet welding conditions with the use of two grades...
-
Resistance to cold cracking of steel joints of P460NL1 steel
PublicationPrzedstawiono wyniki badań odporności na zimne pękanie złączy spawanych ze stali przeznaczonej do pracy pod ciśnieniem. Badano równoczesny wpływ zawartości wodoru dyfundującego i energii liniowej na naprężenie krytyczne w próbie implant dla złączy spawanych elektrodami otulonymi i drutem proszkowym w osłonie gazów ochronnych. Stwierdzono wpływ energii liniowej jak i zawartości wodoru dyfundującego na odporność na zimne pękanie...
-
On the rehabilitation of steel constructions
PublicationW pracy dokonano krótkiego przeglądu literatury z zakresu rewitalizacji i rehabilitacji konstrukcji stalowych. Omówiono podstawowe aspekty rewitalizacji i odnowy tego typu obiektów.
-
Jumping Wave Characteristic during Low Plasticity Burnishing Process
PublicationDuring the low plasticity burnishing process of soft materials such as carbon steel with a hardness of up to 40 HRC (Rockwell grade) a raised structure of the material known as the Jumping Wave forms in front of the tool roll. This phenomenon significantly disturbs the burnishing process, but is very poorly described in the literature. This article presents studies of this phenomenon on the example of burnished 1.0562 steel. The...
-
TRUSS JOINT WITH POSITIVE ECCENTRICITY EXPERIMENTAL RESEARCH
PublicationDue to the technological reasons in modern lightweight steel trusses, fabricated from cold- formed sections, positive eccentricities appear in the truss nodes what induce additional forces in the truss chords. To account for the real load-carrying capacity of truss node area the steel structure research in scale 1:1 were conducted. The experiments consisted of two parts: preliminary and proper one, when conclusions from...
-
Fabrication and Crystal Structure of Sol-Gel Deposited BST Thin Films with Compositional Gradient
PublicationIn the present research technology of compositionally graded barium strontium titanate Ba1-xSrxTiO3 thin films deposited on stainless steel substrates by sol-gel spin coating followed with thermal annealing at T = 650°C is reported. Results of thermal behavior of the sol-gel derived powders with compositions used for fabrication of graded structure (i.e. with Sr mole fraction x = 0.5, 0.4 and 0.3) are described. X-ray diffraction...
-
Assessment of damage causes of a 17 m long wind turbine blade model
PublicationThe subject matter is to verify the stiffness of the steel supporting structure and assess the causes of cracks in the 17 m long wind turbine blade model
-
Zabezpieczenia antykorozyjne stalowych barierek ochronnych na obiektach mostowych w ujęciu kosztów cyklu ich życia
PublicationThe article presents the Life Cycle Costs analysis of steel safety barriers operated in road lane conditions, located on a selected bridge structure. Three corrosion protection systems were proposed, analyzing them in terms of the cost of initial and planned outlays related to maintenance. Based on the LCC analysis for three options, taking into account the 25-year lifetime of the barriers, the optimal solutionwas indicated, i.e....
-
Proposal of Steel weldability quantification.
PublicationPrzedstawiono analizę używanych definicji spawalności i zaproponowano jej zmodyfikowanie. Opracowano metodykę określania wartości względnej spawalności stali stodowanych na konstrukcje spawane. Za podstawę przyjęto uniwersalną skalę jakościową. Dla określenia spawalności uwzględniono szacowanie skłonności do pękania gorącego, zimnego, lamelarnego oraz relaksacyjnego. Ponadto, wzięto pod uwagę wskaźniki eksploatacyjne złącza, takie...
-
Analysis of features of stainless steels in dissimilar welded joints in chloride inducted corrosion
PublicationStainless steels of femtic-austenitic microstructure that means the duplex Cr-Ni-Mo steels, in comparison with austenitic steel includes less expensive nickel and has much better mechanical properties with good formability and corrosion resistance, even in environments containing chloride ions. Similar share of high chromium ferrite and austenite, which is characterized by high ductility, determines that the duplex steels have...
-
ENVIRONMENTAL DEGRADATION OF DISSIMILAR AUSTENITIC 316L AND DUPLEX 2205 STAINLESS STEELS WELDED JOINTS
PublicationThe paper describes structure and properties of dissimilar stainless steels welded joints between duplex 2205 and austenitic 316L steels. Investigations were focused on environmentally assisted cracking of welded joints. The susceptibility to stress corrosion cracking (SCC) and hydrogen embrittlement was determined in slow strain rate tests (SSRT) with the strain rate of 2.2 × 10–6 s–1. Chloride-inducted SCC was determined in the...
-
Strength analysis of the support structure of the offshore wind turbine
PublicationThe global power demand from renewable sources is growing. One of a very favorable solution which meets severe environmental protection requirements are the offshore wind turbines. The offshore wind energy sector has experienced very fast development over last decade. Offshore wind farms, in comparison with onshore applications, can provide increased efficiency with reduced noise, visual, transportation and installation con-flicts....
-
Non-Destructive Assessment of Masonry Pillars using Ultrasonic Tomography
PublicationIn this paper, a condition assessment of masonry pillars is presented. Non-destructive tests were performed on an intact pillar as well as three pillars with internal inclusions in the form of a hole, a steel bar grouted by gypsum mortar, and a steel bar grouted by cement mortar. The inspection utilized ultrasonic stress waves and the reconstruction of the velocity distribution was performed by means of computed tomography. The...
-
Monitoring system of the road embankment
PublicationThe paper presents the monitoring system of the embankment supported on concrete columns and overlaid by a load transfer platform (LTP) with the embedded steel grid. This field investigation was to study the complex inter-action between the columns, the LTP layer, and steel reinforcement via full-scale in situ measurements during erection of the embankment. The study was focused on the behaviour of steel reinforcement and the behaviour...
-
On the correlation between magnetoacoustic emission and magnetostriction dependence on the applied magnetic field
PublicationThe correlation between magnetoacoustic emission signal envelopes and magnetostriction curves is investigated. Two sets of samples are being considered: tempered martensitic steel and plastically deformed ferritic steel. It is shown that even though some general relations may be observed, as was demonstrated in the literature, the correlation is not always present. One may not expect to change both quantities in the same way if...
-
Productivity Enhancement by Prediction of Liquid Steel Breakout during Continuous Casting Process in Manufacturing of Steel Slabs in Steel Plant Using Artificial Neural Network with Backpropagation Algorithms
Publication -
Improving Thermal Insulation Properties for Prefabricated Wall Components Made of Lightweight Aggregate Concrete with Open Structure
PublicationPorous concrete is commonly used in civil engineering due to its good thermal insulation properties in comparison with normal concrete and high compression strength in comparison with other building materials. An extremely porous concrete, called ‘lightweight aggregate concrete with open structure’ (LAC), is used in some German plants to produce prefabricated wall components. They are used mainly in hall buildings, e.g. supermarkets....
-
Review of titanium and steel welding methods
PublicationThe paper presents review of methods of titanium and steel welding. On basis of professional literature it was stated that titanium can be joined with steel by means of explosive welding or brazing.Joining titanium with steel by TIG welding and friction welding methods is possible with the use of copper and tantalum or vanadium interlayer.
-
Strength tests of steel sandwich panel.
PublicationPrzedstawiono wyniki badań laboratoryjnych paneli SANDWICH, prowadzonych w Kat. Technol. Okr. i Obiekt. Oceanotech. Wydz. OiO, na konstrukcjach w skali rzeczywistej. Dokonano porównania uzyskanych rezultatów z wynikami prezentowanymi w literaturze.
-
Modal analysis of cylindrical steel tanks
PublicationCylindrical steel tanks are very popular structures used for storage of products of chemical and petroleum industries. Their safety and reliability is crucial because any failure could have serious consequences. The aim of present paper is to show the results of the first phase of investigation of seismic behaviour such structures. Modal analysis using Finite Element Method (FEM) for three models of real tanks used in Poland has...
-
Underwater Welding of Duplex Stainless Steel
PublicationThe present work was conducted to assess the weldability of duplex stainless steel at underwater conditions. Interest of underwater welding of this steel grade is connected with necessity of preparing welding repair technologies for subsea pipelines widely used in offshore oil and gas industry. The GMA local cavity welding method was used in the investigations. Welded beads were performed underwater at 0.5 m depth and in the air....
-
The resistance of S235JR steel to cavitation erosion
PublicationThe erosion resistance of S235JR steel to flow cavitation was investigated. In order to understand an influence of steel properties and cavitation intensities on the degradation mechanisms, low-carbon S235JR steel was tested in the as-received state and after thermal treatment (annealing) under four different flow velocities. Annealing decreased steel hardness, which made S235JR steel less resistant to cavitation erosion. The performed...
-
Strength tests of steel sandwich panel
PublicationPrzedstawiono wyniki badań laboratoryjnych elementarnego, teowego złącza spawanego laserowo, których celem było określenie pola odkształceń i naprężeń w strefie przyspoinowej. Uzyskane wyniki wskazują na potrzebę bardzo starannego modelowania konstrukcji spawanych laserowo przy obliczeniach MES. W pracy zaprezentowano wyniki badań konstrukcji rzeczywistej pod statycznym obciążeniem ściskającym, które porównano z rezultatami analizy...
-
Strength tests of steel sandwich panel
PublicationPrzedstawiono wyniki badań laboratoryjnych elementarnych złączy spawanych laserowo i paneli SANDWICH, prowadzonych w Katedrze Technologii Okrętów i Obiektów Oceanotechnicznych WOiO, na konstrukcjach w skali rzeczywistej. Dokonano analizy zachowania połączenia podczas procesu obciążenia. Przedstawiono wyniki numerycznego zamodelowania własności złącza. Dokonano porównania uzyskanych rezultatów analizy numerycznej z wynikami z badań...
-
Effect of Arc Strikes on High Strength Low Alloy Steels Welded by SMAW
PublicationWet welding with covered electrodes (Shielded Metal Arc Welding – SMAW) is the most commonly used method of carrying out welding repair works in a water environment. Limited visibility and the inability to move freely under water result in an increased risk of formation of welding imperfections such as lack of fusion, lack of penetration and arc strikes. The work focused on changes in the properties and structure of steel subjected...
-
Investigation of behaviour of metal structures with polymer dampers under dynamic loads
PublicationA large number of accidents concerning structures subjected to dynamic loads have been recently observed. One of the examples of such a structure is a temporary steel grandstand erected using scaffolding system. Dynamic load that is generated by crowd movement has a significant influence on the behaviour of the structure and may lead to excessive structural vibrations. The aim of the study is to consider the idea of using polymer...
-
Deposition of phosphate coatings on titanium within scaffold structure
PublicationPurpose: Existing knowledge about the appearance, thickness, and chemical composition of phosphate coatings on titanium inside porous structures is insufficient. Such knowledge is important for the design and fabrication of porous implants. Methods: Metallic scaffolds were fabricated by selective laser melting of 316L stainless steel powder. Phosphate coatings were deposited on Ti sensors placed either outside the scaffolds or...
-
The validation process of truss model with joint eccentricities
PublicationNowadays, due to the technological reasons in modern lightweight steel trusses, fabricated from cold-formed sections, positive eccentricities appear in the truss nodes, to induce additional forces truss chords. In order to account for the real load-carrying capacity of truss node area the steel structure research was conducted in scale 1:1. As a result of experimental research, the forms of deformation and strains of the walls...
-
Corrosion performance of super duplex stainless steel and pipeline steel dissimilar welded joints: a comprehensive investigation for marine structures
PublicationThis study investigates the corrosion behavior of dissimilar gas tungsten arc (GTA) welded joints between super duplex stainless steel (sDSS 2507) and pipeline steel (X-70) using electrochemical and immersion corrosion tests. The GTA welds were fabricated using ER2594 and ER309L fller metals. The study examined the electrochemical characteristics and continuous corrosion behavior of samples extracted from various zones of the weldments...
-
Wire Arc Additive Manufactured Mild Steel and Austenitic Stainless Steel Components: Microstructure, Mechanical Properties and Residual Stresses
PublicationWire arc additive manufacturing (WAAM) is an additive manufacturing process based on the arc welding process in which wire is melted by an electric arc and deposited layer by layer. Due to the cost and rate benefits over powder-based additive manufacturing technologies and other alternative heat sources such as laser and electron beams, the process is currently receiving much attention in the industrial production sector. The gas...
-
Fatigue life of steel, laser welded panels
PublicationW publikacji przedstawiono zagadnienia dotyczące możliwości analizy trwałości zmęczeniowej stalowyxh paneli spawanych laserowo typu sandwich. Przedstawiono wyniki badań laboratoryjnych w skali naturalnej a także krzywe projektowe uzyskane na podstawie systematycznych badań połączeń elementarnych spawanych laserowo. Na podstawie przedstawionych i uogólnionych wyników pokazano propozycję metodyki szacowania trwałości zmęczeniowej...
-
Grease effect on fretting wear of mild steel
PublicationNa stanowisku laboratoryjnym przeprowadzono badania zużycia frettingowego miękkiej stali smarowanej mineralnymi i syntetycznymi smarami zawierającymi także różne dodatki: grafit dwusiarczek molibdenu ZDDP i ditiocarbamat molibdenu, w różnych stężeniach.Badania wykazały istotny wpływ konsystencji smaru i jego właściwości smarnych na zużycie frettingowe miękkiej stali oraz zróżnicowany wpływ testowanych dodatków. Obecność smaru...
-
Protective coatings for stainless steel for SOFC applications
PublicationW pracy przedstawiono badania związane z warstwami antykorozyjnymi stali nierdzewnych stosowanych w tlenkowych ogniwach paliwowych. Warstwy przygotowana z użyciem prekursorów polimerowych na bazie Y i Co. Użyta stal to Crofer 22 APU.
-
The Laser Surface Remelting of Austenitic Stainless Steel
Publication -
Fatigue Behaviour of Sintered Duplex Stainless Steel
Publication -
Damage Detection of Steel-Concrete Composite Beam
Publication -
Pitting corrosion in steel and electrochemical noise intensity
Publication -
Uniform corrosion monitoring of carbon steel in concrete
Publication -
Study on the strength of laminated polyurethane-steel joints
Publication -
Attempts to Modify Austenitic Steel with Carbon Nanotubes
Publication -
Numerical Simulation of Duplex Steel Multipass Welding
Publication -
Corrosion of AISI1018 and AISI304 steel exposed to sulfates
Publication -
Uniform corrosion monitoring of carbon steel in concrete.
PublicationW przypadku korozji prętów zbrojeniowych w żelbecie zaobserwowane zostały obszary wzmożonego zaatakowania. Pomiar prądowego i napięciowego szumu elektrochemicznego umożliwia wyznaczenie szybkości korozji ogólnej a zmiany parametrów statystycznych przebiegów szumowych umożliwiają detekcję występowania przestrzennych rejonów intensyfikacji korozji. Przedstawione rezultaty, oparte na wykorzystaniu odpowiedniego układu zastępczego,...