displaying 1000 best results Help
Search results for: surface geometrical structure
-
Improving Output Performance of the Ultrasonic Multicell Piezoelectric Motor by Development the Multi-Rotor Structure
PublicationIn recent years, many researches have been carried out on piezoelectric multi-rotor structures. This paper describes the analysis, development and experimental process of an ultrasonic multi-cell piezoelectric motor using a multi-rotor structure. In this design, three independent cells have been integrated into a mechatronic system. Analytical model and finite element method are used for modal and dynamic analysis of the proposed...
-
Surface properties and photocatalytic activity of KTaO3, CdS, MoS2 semiconductors and their binary and ternary semiconductor composites
PublicationSingle semiconductors such as KTaO3, CdS MoS2 or their precursor solutions were combined to form novel binary and ternary semiconductor nanocomposites by the calcination or by the hydro/solvothermal mixed solutions methods, respectively. The aim of this work was to study the influence of preparation method as well as type and amount of the composite components on the surface properties and photocatalytic activity of the new semiconducting...
-
Analysis of pavement structure sensitivity to passage of oversized heavy duty vehicle in terms of bearing capacity
PublicationOversized heavy duty vehicles occur in traffic very rarely but they reach extremely high weights, even up to 800 tonne. The detrimental impact of these vehicles on pavement structure is much higher than in case of commercial vehicles that comprise typical traffic, thus it is necessary to assess the sensitivity of pavement structure to passage of oversized vehicles. The paper presents results of sample calculations of load equivalency factor...
-
SEM examination of surface layer of C45 steel after grinding on defferent depth
Open Research DataFerrite examination for the medium carbon structural steel with low content of Mn, Si, Cu, Cr and Ni after its grinding to a depth of 2 µm, 8 µm, 14 µm and 20 µm, at constant wheel circumferential speed of vs = 25 m/s and constant feed rate vft = 1 m/min. It was shown that the grinding of C45 steel causes strong work hardening of ferrite in surface...
-
Computing methods for fast and precise body surface area estimation of selected body parts
PublicationCurrently used body surface area (BSA) formulas give satisfactory results only for individuals with typical physique, while for elderly, obese or anorectic people accurate results cannot be expected. Particularly noteworthy are the results for individuals with severe obesity (body-mass index greater than 35 kg/m2), for which BSA estimation errors reached 80%. The main goal of our study is the development of precise BSA models for...
-
Influence of the laser remelting parameters on the thickness of surface layers created on the stainless steel X5CrNi18-10
PublicationIn this work the surface of austenitic stainless steel type X5CrNi18-10 was treated by using laser. Laser remelting was done by means of laser MLT 2500 CO2 with different parameters of treatment: P - power beam (800 [W], 1000 [W], 1100 [W], 1200 [W]); v - scanning velocity (6 [mm/s], 7 [mm/s], 8 [mm/s]); diameter of laser beam (1.4 [mm], 1.6 [mm]). The influence of these parameters on the thickness and shape of layers in manufacturing...
-
Surface EMG-based signal acquisition for decoding hand movements
Open Research DataBiosignal processing plays a crucial role in modern hand prosthetics. The challenge is to restore functionality of a lost limb based on the signals acquired from the surface of the stump. The number of sensors (emg channels) used for signal acquisition influence the quality of a prosthetic hand. Modern algorithms (including neural networks) can significantly...
-
The electrochemical studies of CB-PLA electrode after surface activation by proteinase K digestion with different times and concentrations
Open Research DataThe dataset contains the electrochemical studies performed to evaluate surface activation of the CB-PLA 3D printed electrodes by enzymatic hydrolysis in a solution containing proteinase K. DIfferent proteinase K concentrations and digestion times were evaluated, as described in subfolder names. The studies were performed before surface activation, during...
-
Synthesis, structure and properties of novel poly(hydroxyurethane)s obtained by non-isocyanate route
PublicationNon-isocyanate polyurethanes (NIPUs) can be synthesized by polyaddition of five-membered bis(cyclic carbonate)s and primary diamines. NIPUs are an alternative for the commonly used (in the form of foams, elastomers, coatings or fibers) in the industry polyurethanes obtained using toxic and moisture sensitive diisocyanates, polyols and low-molecular weight chain extenders. The main aim of this work was to synthesize non-isocyanate...
-
The structure of the data flow in integrated urban traffic management systems – the case of TRISTAR system
PublicationThe purpose of the article is to offer some insight into the data flow architecture in the Tri-City’s integrated traffic management system called TRISTAR. To that end selected elements of TRISTAR are identified and described as well as the structure for collecting and exchanging data within different sub-systems. Finally, the article highlights how the TRISTAR system can be extended by adding new elements and modules.
-
Shaping of the workpiece surface in single-disc lapping
PublicationShape errors of the tool exert a dominant influence on the shape accuracy of the workpiece. The correlation between flatness errors of the lap and flatness errors of the workpieces was checked experimentally and determined analytically. Computer model of the workpiece shaping by lapping was developed. Evaluation method of the workpiece orientation as well as some simulation results for a lap with shape errors of convexity and cincavity...
-
Mesoscopic impedance analysis of solid materials’ surface
Publication -
Concept of Neural Model of the Sea Bottom Surface
Publication -
Surface vaviness of components machined by burnishing method
PublicationPowierzchnię po obróbce wykończeniowej definiuje się zazwyczaj za pomocą parametrów chropowatości. Rosnące wymagania jakościowe w stosunku do wytwarzanych części maszyn powodują rozszerzanie się zakresu parametrów opisujących powierzchnię. W artykule przedstawiono ocenę jakościową powierzchni nagniatanych za pomocą parametrów falistości.
-
Influence of dissolved organic nitrogen on surface waters
PublicationThe aim of this study was to determine the susceptibility of dissolved organic nitrogen (DON) contained in biologically treated wastewater disposed from municipal wastewater treatment plants (WWTPs) to biodegradability and bioavailability in a water environment. Additionally an evaluation was performed of the participation of this organic nitrogen fraction, including bioavailable DON (bDON), in the nitrogen balance for the Baltic...
-
Some aspects surface cooling by impinging jet
PublicationW pracy przedstawiono wyniki badań wymiany ciepła, uskoku hydraulicznego i stabilności podczas napływu strugi na powierzchnię ciała stałego.
-
Shaping of the workpiece surface in single-disc lapping
PublicationPrzedstawiono korelację pomiędzy błędami kształtu docieraka i błędami kształtu przedmiotów obrabianych. Wyniki analityczne zostały sprawdzone doświadczalnie, co pozwoliło zbudować komputerowy model kształtowania powierzchni docieranych. Przedstawiono sposób wyznaczania intensywności kontaktu między przedmiotem docieranym, a docierakiem. Opracowano metodę wyznaczania położenia przedmiotu na docieraku.
-
Probabilistic analysis of slope with planar slip surface
PublicationPraca dotyczy probabilistycznej oceny stateczności zboczy. Omówiono sposób określania prawdopodobieństwa utraty stateczności przy wykorzystaniu metody momentów (ang. FOSM). Podejście takie zastosowano do analizy zsuwu konsekwentnego jednorodnego zbocza. Rozpatrzono wpływ zmienności statystycznej parametrów wytrzymałościowych na końcowe wyniki.
-
Formation of wood surface roughness in burnishing process
PublicationW publikacji przedstawiono i omówiono rozwój bezwiórowych metod obróbki wykańczającej drewna przez nagniatanie. Przedstawiono wpływ nagniatania na chropowatość powierzchni drewna. Badania przeprowadzono na próbkach toczonych i nagniatanych. Wyniki odniesiono do głównych parametrów nagniatania jak: siła nagniatania oraz promień zaokrąglenia elementu nagniatającego.
-
Problems of flat surface lapping : chapter 16
PublicationPrzedstawiono problemy docierania powierzchni płaskich w układach jednotarczowych. Omówiono analityczne i numeryczne modele kinematyki docierarek konwencjonalnych i niestandardowych, obróbkę docierakami aktywizowanymi w sposób swobodny i wymuszony, jednolitymi i dwumetalowymi. Zaprezentowano wyniki obróbki narzędziami ścierno-metalowymi elementów ceramicznych.
-
Evolution of the surface species of the V2O5–WO3 catalysts
Publication -
Total mercury in surface sediments of the Gdansk Basin
Publication -
New procedure of silica gel surface modification
Publication -
Comparison of volume-and surface-detention-time distributions
PublicationCzas zatrzymania ścieków w reaktorze jest bardzo ważnym parametrem projektowym. Jego wyznaczenie jest trudne i kłopotliwe. Z tego względu zbadano możliwość zastąpienia wartości tego parametru, wyznaczonej tylko dla swobodnej powierzchni ścieków. W wyniku stwierdzono dopuszczalność takiej zamiany.
-
Mesoscopic impedance analysis of solid materials surface
PublicationSeveral techniques have been developed in order to characterize electrical properties of surfaces in micrometer/nanometer scale. Obtaining of the spatial distribution of sample resistance, capacitance or potential requires separate measurements performed in different scanning modes. On the other hand, analysis of the frequency response of investigated system enables determination of several physical quantities in single measurement...
-
Hydrothermal Surface Treatment of Biodegradable Mg-Materials
Publication -
Surface studies of twinned of YBa2Cu3O7−δ crystals
Publication -
Surface contamination after lapping by abrasive material
PublicationPrzedstawiono wyniki badań skażenia powierzchni żeliwa sferoidalnego mikroziarnami węglika krzemu po docieraniu. Określowo wpływ współczynnika upakowania mikroziaren w strefie docierania na intensywność skażenia powierzchni ścierniwem. W badaniach wykorzystano powierzchniową mikroanalizę rentgenowską.
-
The Effect of Dimple Distortions on Surface Topography Analysis
Publication -
Reduction of the end-effect in surface texture analysis
Publication -
Detection of measurement noise in surface topography analysis
Publication -
Problems of surface topography with oil pockets analysis
Publication -
Effect of surface modification on starch biopolymer wettability
Publication -
Effect of surface modification on starch/phospholipid wettability
Publication -
The Laser Surface Remelting of Austenitic Stainless Steel
Publication -
The evaluation of the surface quality after laser cutting
Publication -
Mechanism for sonocoating a polymer surface with nano-hydroxyapatite
Publication -
Innovative Solutions in Surface Water Quality Monitoring
PublicationIn 2010 a project entitled "Integrated Support System for Management and Protection of Water Dam Reservoir (ZiZOZap)” was initiated, to aid solving water management problems on a river and dam reservoir formed on it. An innovative system of continuous monitoring was created, that encompassed selected physical and chemical parameters of river and lake waters in three chosen sites. This article presents a selection of results, that...
-
Novel 2019 coronavirus structure, mechanism of action, antiviral drug promises and rule out against its treatment
Publication -
Atomic resolution crystal structure of HV-BBI protease inhibitor from amphibian skin in complex with bovine trypsin
Publication -
Hydrazinolysis Products of Selected Sugar Lactones—Crystal Structure and Microbiological Activity
PublicationCommercially available lactones, as well as those synthesized by us, turned out to be good substrates for the synthesis of sugar hydrazides. The exception was L-ascorbic acid, whose hydrazinolysis led to the formation of a hydrazinium salt, not the hydrazide as expected. The structure of all compounds was confirmed by NMR and X-ray analyses. The lower durability of hydrazinium L-ascorbate was additionally confirmed by thermogravimetric...
-
Reduction of vibrations of steel structure models with Polymeric Bearings - experimental study
PublicationEarthquake-induced ground motions are the most severe and unpredictable threats to the structures all around the world. Therefore, designing earthquake protective systems has become an extremely challenging problem in civil engineering. Base isolation is one of the most popular and widely adopted methods of protecting structures against earthquake forces. The present paper reports the results obtained from the shaking table experimental...
-
The Effect of Calcination Temperature on Structure and Photocatalytic Properties of WO3/TiO2 Nanocomposites
PublicationSeries ofWO3/TiO2 nanocompositeswere obtained by hydrothermal method followed by calcination in the temperature range from 400∘C to 900∘C. The characteristics of photocatalysts by X-ray diffractometry (XRD), scanning electron microscope (SEM), and diffuse reflectance spectroscopy (DRS) showed that increasing the calcination temperature from 400 to 900∘C resulted in change of photocatalytic activity under UV-Vis light.Moreover,...
-
Assessment of copper surface coverage with corrosion inhibitor using AFM-based local electrical measurements
PublicationThe paper presents a new method of assessment of metal surface coverage with corrosion inhibitor and thus of inhibitor protective performance. It is based on the atomic force microscopy measurement performed in a contact mode. Apart from topography images the proposed approach allows acquisition of local DC maps and local electrical impedance spectra via application of DC bias voltage or AC perturbation signal between the conductive...
-
Experimental Tests Of Sandwich Beams In The Design Process Of GFRP Shell Footbridge Structure
PublicationThe paper includes selected aspects of the study to elaborate architectural, material and construction design of pedestrian footbridge spans made of composite materials. The considered footbridge is a sandwich-type shell structure. The cooperation of PET foam core with outer lining surfaces is crucial for its load bearing capacity. The paper is aimed to experimental investigation of sandwich beams subjected to bending loading....
-
Dynamic Electrochemical Impedance Spectroscopy (DEIS) as a Tool for Analyzing Surface Oxidation Processes on Boron-Doped Diamond Electrodes
PublicationSurface oxidation processes play a key role in understanding electrochemical properties of boron-doped diamond (BDD) electrodes. The type of surface termination groups, which create the potential window of electrolytic water stability or hydrophobicity, influences such properties. In this study the kinetics of oxidation process under anodic polarization were studied in situ by means of Dynamic Electrochemical Impedance Spectroscopy...
-
Analysis of Validation and Simplification of Timber-Frame Structure Design Stage with PU-Foam Insulation
PublicationThe transition from experimental studies to the realm of numerical simulations is often necessary for further studies, but very difficult at the same time. This is especially the case for extended seismic analysis and earthquake-resistant design. This paper describes an approach to moving from the experimental testing of an elementary part of a wood-frame building structure to a numerical model, with the use of a commercial engineering...
-
Fracture Surface Behavior of 34CrNiMo6 High-Strength Steel Bars with Blind Holes under Bending-Torsion Fatigue
PublicationThe present study evaluates the fracture surface response of fatigued 34CrNiMo6 steel bars with transverse blind holes subjected to bending with torsion loading. The analysis of the geometric product specification was performed by means of height parameters Sx, functional volume parameters Vx, and fractal dimension Df. Surface topography measurements were carried out using an optical profilometer with focus variation technology....
-
Eco-Friendly Ether and Ester-Urethane Prepolymer: Structure, Processing and Properties
PublicationThis study concerns bio-based urethane prepolymers. The relationship between the chemical structure and the thermal and processing parameters of bio-based isocyanate-terminated ether and ester-urethane prepolymers was investigated. Bio-based prepolymers were obtained with the use of bio-monomers such as bio-based diisocyanate, bio-based polyether polyol or polyester polyols. In addition to their composition, the bio-based prepolymers...
-
Structure of foreigners registered for retirement and disability pension insurance by citizenship (%) - at the end of the year
Open Research DataThe structure of foreigners registered for insurance, divided by citizenship, changed dynamically. The share of foreigners from the EU regularly decreases (from 25.1% in December 2008 to 6.3% in December 2018), while the share of foreigners from outside the EU is steadily growing (from 74.9% in December 2008 to 93.7% in December 2018). The largest changes...