Search results for: TIRE RUBBER HARDNESS
-
Recent Advances in Development of Waste-Based Polymer Materials: A Review
PublicationLimited petroleum sources, suitable law regulations, and higher awareness within society has caused sustainable development of manufacturing and recycling of polymer blends and composites to be gaining increasing attention. This work aims to report recent advances in the manufacturing of environmentally friendly and low-cost polymer materials based on post-production and postconsumer wastes. Sustainable development of three groups...
-
INFLUENCE OF SOLID PARTICLE CONTAMINATION ON THE WEAR PROCESS IN WATER LUBRICATED MARINE STRUT BEARINGS WITH NBR AND PTFE BUSHES
PublicationThis paper reports on a study of the influence of solid particle contamination on the wear process in water-lubricated slide bearings (steel-acrylonitrile-butadiene rubber (NBR) and steel- polytetrafluoroethylene (PTFE)). To compare the wear of the shaft journal and bushes (NBR and PTFE) when lubricated with fresh water and contaminated water, an experiment was carried out to identify key factors that influence the state of wear...
-
Napawanie elementów wymiennika ciepła austenitycznym drutem proszkowym
PublicationNa potrzeby przemysłu energetycznego produkuje się wymienniki ciepła przeznaczone do eksploatacji w warunkach agresywnych chemicznie, np. w środowisku siarkowodoru. Z przyczyn ekonomicznych często stosuje się w takim przypadku materiały bimetaliczne wytwarzane procesami napawania. W artykule przedstawiono wyniki badań nieniszczących, pomiarów twardości, analizy składu chemicznego, pomiarów ferrytu delta oraz badań makro- i mikroskopowych...
-
Cavitation Erosion Resistance Influence of Material Properties
PublicationThe cavitation erosion is the phenomena that causes degradation of fluid flow machinery components due to repetitive implosion of cavitation bubbles adjacent to the solid surface. Cavitation erosion is a complex phenomenon, which includes not only hydrodynamic factors of liquid, but also properties of erodible material e.g. microstructure, hardness or Young modulus. In order to reduce the negative impact of erosion on machine components,...
-
Influence of cooling rate and additives on low-temperature properties of asphalt mixtures in the TSRST
PublicationThe paper presents the results and analysis of low-temperature properties of asphalt mixtures according to Thermal Stress Restrained Specimen Test (TSRST) and Indirect Tensile Test methods. Different groups of bitumen were investigated: neat, SBS-modified and highly SBS-modified. Influence of cooling rates (1 C/h, 3 C/h, 5 C/h and 10 C/h) and additives (aramid fibres and crumb rubber) was identified as well. Moreover, for each...
-
Isothermal Vulcanization and Non-Isothermal Degradation Kinetics of XNBR/Epoxy/XNBR-g-Halloysite Nanotubes (HNT) Nanocomposites
PublicationThe effect of several concentrations of carboxylated nitrile butadiene rubber (XNBR) functionalized halloysite nanotubes (XHNTs) on the vulcanization and degradation kinetics of XNBR/epoxy compounds were evaluated using experimental and theoretical methods. The isothermal vulcanization kinetics were studied at various temperatures by rheometry and differential scanning calorimetry (DSC). The results obtained indicated that the...
-
RESIDUE ANALYSIS OF ETU AND PTU BY LC/MS
PublicationDithiocarbamates (DTCs) are important organosulfur compounds, which act as inhibitors of metal dependant and sulphydryl enzymes and have a serious consequence on biological systems. They possess variety of applications in agriculture as fungicides, as well as, in the rubber industry as vulcanization accelerators and antioxidants. In this way, DTCs are the main group of fungicides used to control approximately 400 pathogens of more...
-
The Influence of Laser Alloying of Ti13Nb13Zr on Surface Topography and Properties
PublicationThe laser alloying is a continually developing surface treatment because of its significant and specific structuration of a surface. In particular, it is applied for Ti alloys, being now the most essential biomaterials` group for load-bearing implants. The present research was performed on the Ti13Nb13Zr alloy subject to laser modification in order to determine the treatment effects on surface topography and its some mechanical...
-
The resistance of S235JR steel to cavitation erosion
PublicationThe erosion resistance of S235JR steel to flow cavitation was investigated. In order to understand an influence of steel properties and cavitation intensities on the degradation mechanisms, low-carbon S235JR steel was tested in the as-received state and after thermal treatment (annealing) under four different flow velocities. Annealing decreased steel hardness, which made S235JR steel less resistant to cavitation erosion. The performed...
-
Influence of dispersed phase content on the mechanical properties of electroless nanocomposite Ni-P/Si3N4 and hybrid Ni-P/Si3N4/graphite layers deposited on the AW-7075 alloy.
PublicationThe article presents the results of mechanical testing of Ni-P/Si3N4 nanocomposite and hybrid Ni-P/Si3N4/graphite coatings deposited on AW-7075 aluminum alloy using the chemical reduction method. In terms of mechanical testing, microhardness was measured, and surface roughness and adhesion of the coatings to the aluminum substrate were determined using the “scratch test” method. The surface morphology of the deposited layers was...
-
Effect of Impoundment on Physico-chemical Properties of Water in the Flowing through stream, the Case of the Turawa Reservoir
PublicationThe Turawa reservoir is one of the most important storage reservoirs in Poland. Quite many physico-chemical parameters of water in the reservoir itself and also in the Mała Panew, the river flowing through the reservoir were measured at various periods of the year. Measuring and sampling points were situated at the river inflow, over the reservoir, and at the river outflow. The parameters included temperature, electrical conductivity,...
-
A COMPARISON OF WEAR PROPERTIES OF WATER LUBRICATED NBR AND PTFE SLIDING BEARINGS
PublicationThe excessive wear of a journal shaft can be caused by many factors, for example, working conditions (e.g., temperaturę, slip speed, the type of lubricant), pressure, the type of material used on the bearings and shafts and their roughness, as well as contamination remaining in the system. This paper presents the roughness profiles co-operating with a rubber (NBR) and polytetrafluoroethylene (PTFE) bushes. The conditions of cooperation...
-
A Review of Hyperelastic Constitutive Models for Dielectric Elastomers
PublicationDielectric elastomers are smart materials that are essential components in soft systems and structures. The core element of a dielectric elastomer is soft matter, which is mainly rubber-like and elastomeric. These soft materials show a nonlinear behaviour and have a nonlinear strain-stress curve. The best candidates for modelling the nonlinear behaviour of such materials are hyperelastic strain energy functions. Hyperelastic functions...
-
Effect of Variation of Hard Segment Content and Graphene-Based Nanofiller Concentration on Morphological, Thermal, and Mechanical Properties of Polyurethane Nanocomposites
PublicationThis study describes the development of a new class of high-performance polyurethane elastomer nanocomposites containing reduced graphene oxide (RGO) or graphene nanoplatelets (GNP). Two types of polyurethane elastomers with different contents of hard segments (HS) were used as a polymer matrix. The developed nanocomposites were characterized by thermal analysis (DSC, TG), dynamic mechanical testing (DMA), hardness testing, mechanical...
-
Characterization of structural, thermal and mechanical properties of bismuth silicate glasses
Publicationhe influence of heating and reduction processes on the structural, thermal and mechanical properties of bismuth-silicate glasses has been investigated. Two compositions of glasses: 40Bi2O3–60SiO2 (Bi0.57Si0.43Ox) and 27Bi2O3–73SiO2 (Bi0.43Si0.57Ox) were fabricated by a typical melt quenching technique. Then the reduction in hydrogen at 380 °C for 20, 42 or 67 h was performed. It was found that a 50 μm-thick layer was formed on...
-
Underwater in situ local heat treatment by additional stitches for improving the weldability of steel
PublicationIn this paper the influence of in situ local heat treatment performed by additional stitches on the weldability of high-strength low-alloy (HSLA) S355J2C+N steel was tested. The investigated steel is characterized by high susceptibility to cold cracking. It is necessary to find a method to improve the quality of welded joints. The local heat treatment was applied as an eect of bead-on plate welding made on the face of a Tekken...
-
Metallurgical characterization and high-temperature tensile failure of Inconel 617 alloy welded by GTAW and SMAW—a comparative study
PublicationTwo types of the weld joint of Inconel 617 alloy were produced using gas tungsten arc welding (GTAW) and shielded metal arc welding (SMAW) processes with ERNiCrCoMo-1 filler metal and ENiCrCoMo-1 electrode, respectively. The weld metal showed the segregation of the principle alloying elements like Mo and Cr along the inter-dendritic spaces, triggering the formation of secondary phases. The microstructure characterization of the...
-
Underwater wet welding of S1300 ultra-high strength steel
PublicationMarine Structures Volume 81, January 2022, 103120 Underwater wet welding of S1300 ultra-high strength steel Author links open overlay panelJacekTomkówGrzegorzRogalski https://doi.org/10.1016/j.marstruc.2021.103120 Get rights and content Under a Creative Commons licenseopen access Highlights • Technological method of S1300 steel underwater weldability improving was proposed. • Number of cracks and hardness of welded joints was...
-
Simulation of the response of base-isolated buildings under earthquake excitations considering soil flexibility
PublicationThe accurate analysis of the seismic response of isolated structures requires the incorporation of the flexibility of supporting soil. However, it is often customary to idealize the soil as rigid during the analysis of such structures. In the present paper, seismic response time history analyses of base-isolated buildings modelled as single degree-of-freedom (SDOF) and multi degree-of-freedom (MDOF) systems with linear and nonlinear...
-
Minimum vertex ranking spanning tree problem for chordal and proper interval graphs
PublicationW pracy rozważamy problem szukania, dla danego grafu prostego, drzewa spinającego, którego uporządkowana liczba chromatyczna jest minimalna. K.~Miyata i inni dowiedli w [Np-hardness proof and an approximation algorithm for the minimum vertex ranking spanning tree problem,Discrete Appl. Math. 154 (2006) 2402-2410], że odpowiedni problem decyzyjny jest NP-trudny już w przypadku pytania o istnienie uporządkowanego 4-pokolorowania....
-
Application of the near-infrared spectroscopy in the pharmaceutical technology
PublicationNear-infrared (NIR) spectroscopy is currently the fastest-growing and the most versatile analytical method not only in the pharmaceutical sciences but also in the industry. This review focuses on recent NIR applications in the pharmaceutical technology. This article covers monitoring, by NIR, of many manufacturing processes, such as granulation, mixing or drying, in order to determine the end-point of these processes. In this...
-
The influence of welding heat input on the quality and properties of high strength low-alloy dissimilar steel butt joints
PublicationThe paper presents the results of non-destructive and destructive tests of dissimilar highstrength low-alloy S460ML and S460N steel butt joints. These steels are characterized by similar mechanical properties, but their carbon equivalent CeIIW values are much different. The joints were made using different values of heat input for each welding bead. They were tested by non-destructive methods: visual, penetrant, radiographic and...
-
Thermal and mechanical properties of polyurethanes modified with L-ascorbic acid
PublicationIn this study we report the thermal and mechanical properties of polyurethanes modified with ascorbic acid (AA). Ascorbic acid was used as a modifier at concentration of 1 or 2 mass%. The antioxidative properties of AA may improve the biocompatibility of the obtained materials, which were designed for biomedical applications. In this paper we describe characterization of obtained unmodified and ascorbic acid modified polyurethanes...
-
Effects of Laser Remelting at Cryogenic Conditions on Microstructure and Wear Resistance of the Ti6Al4V Alloy Applied in Medicine
PublicationThe titanium and its alloys can be subjected to surface treatment, including laser treatment. In this work a new laser treatment at cryogenic conditions of Ti6Al4V alloy has been described. The work has been aimed at establishing whether such surface treatment could be suitable for implants working under wear in biological corrosive environment. The remelting has been made with the use of CO2 continuous work laser at laser power...
-
Clearing directed subgraphs by mobile agents
PublicationWe study several problems of clearing subgraphs by mobile agents in digraphs. The agents can move only along directed walks of a digraph and, depending on the variant, their initial positions may be pre-specified. In general, for a given subset S of vertices of a digraph D and a positive integer k, the objective is to determine whether there is a subgraph H=(V,A) of D such that (a) S is a subset of V, (b) H is the union of k directed...
-
Effect of Porosity on the Thermo-Mechanical Behavior of Friction-Stir-Welded Spark-Plasma-Sintered Aluminum Matrix Composites with Bimodal Micro- and Nano-Sized Reinforcing Al2O3 Particles
PublicationThe thermo-mechanical behavior of nanosized Al2O3 particles reinforcing aluminum was analyzed in the present paper. The material was prepared by spark plasma sintering and friction stir welding. The thermal stresses affecting the composite behavior during welding were modeled through COMSOL MultiPhysics, and the results were validated by the analyses of the composites’ mechanical properties. The spark-plasma-sintered materials...
-
Assessment of the devulcanization process of EPDM waste from roofing systems by combined thermomechanical/microwave procedures
PublicationEthylene-propylene-diene rubber (EPDM) is a elastomer widely used in common industrial applications. EPDM can be shaped into sheets and employed as isolating material for roofing systems. In this study, scraps of EPDM from commercial, industrial and residential roofing systems were treated by combined thermo-mechanical and microwave devulcanization processes including peroxide of benzoyl (BPO). The devulcanized EPDM (Dev-EPDM)...
-
Underwater Local Cavity Welding of S460N Steel
PublicationIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Study on Microstructure and Mechanical Properties of Laser Welded Dissimilar Joint of P91 Steel and INCOLOY 800HT Nickel Alloy
PublicationThis investigation attempts to explore the weld characteristics of a laser welded dissimilar joint of ferritic/martensitic 9Cr-1Mo-V-Nb (P91) steel and Incoloy 800HT austenitic nickel alloy. This dissimilar joint is essential in power generating nuclear and thermal plants operating at 600–650 °C. In such critical operating conditions, it is essential for a dissimilar joint to preserve its characteristics and be free from any kind...
-
Pavement ageing influence on tyre/road noise
PublicationRoad surface should be constructed in a way that ensures safe and comfortable traffic conditions, not only when it is newly paved but also during its entire lifetime. An important factor in the asphalt mixture design process is also the expected pavement durability and stability of pavement properties over time. In many countries, road surface starts to play a significant role in traffic noise reduction actions. Selecting a particular...
-
The Method of Selecting the Interval of Functional Tests Taking into Account Economic Aspects and Legal Requirements
PublicationThe article discusses the problem of choosing the optimal frequency of functional tests, taking into account the reliability and law requirements, but also the impact of business aspects in the company. The subject of functional test interval is well described for purposes of the process industry. Unfortunately, this is not the case for the machinery safety functions with low demand mode. This is followed by a presentation of the...
-
Comparative analysis of earthships and conventional buildings in terms of investment and operating costs
PublicationThe aim of the master's thesis is to present the idea of earthships and compare them with conventional buildings in terms of investment and operating costs. Earthships are buildings erected from tires and other wastes whose characteristic feature is their self-sufficiency. The first part of the master's thesis is to discuss the basic issues related to the earthship building. The beginnings of tire homes and their development are...
-
Searching by heterogeneous agents
PublicationIn this work we introduce and study a pursuit-evasion game in which the search is performed by heterogeneous entities. We incorporate heterogeneity into the classical edge search problem by considering edge-labeled graphs: once a search strategy initially assigns labels to the searchers, each searcher can be only present on an edge of its own label. We prove that this problem is not monotone even for trees and we give instances...
-
Improvement of S355G10+N steel weldability in water environment by Temper Bead Welding
PublicationThe normalized S355G10 + N steel was chosen for testing, it is used in a variety of applications including the building of offshore structures, which may require repairs in water environment. The main aim of the work was to check susceptibility to cold cracking for fillet welds – Controlled Thermal Severity (CTS) tests and butt welds – Tekken tests and in the next step evaluation of effectiveness of Temper Bead Welding (TBW) application...
-
The Influence of Nanometals, Dispersed in the Electrophoretic Nanohydroxyapatite Coatings on the Ti13Zr13Nb Alloy, on Their Morphology and Mechanical Properties
PublicationIn this work, nanohydroxyapatite coatings with nanosilver and nanocopper have been fabricated and studied. The presented results concern coatings with a chemical composition that has never been proposed before. The present research aims to characterize the effects of nanosilver and nanocopper, dispersed in nanohydroxyapatite coatings and deposited on a new, non-toxic Ti13Zr13Nb alloy, on the physical and mechanical properties of...
-
The effect of high pressure at subzero temperature on proteins solubility, drip loss and texture of fish (cod and salmon) and mammal’s (pork and beef) meat
PublicationOne of the possibilities of using high pressure technique in inactivation of microorganism is conducting this process at subzero temperature. However, for its practical application in meat preservation the appropriate properties of meat should be kept. Therefore, the aim of this work was to examine the effect of pressure at subzero temperature (without freezing of water) on proteins and texture of mammal’s and cold-adapted fish...
-
Synthesis, Structure and Properties of Poly(ester-Urethane-Urea)s Synthesized Using Biobased Diamine
PublicationModern polymer science and technology is focused on the development of partial or fully green polymers. This focus is related to green chemistry trends, which propose using natural and renewable resources as monomers in the synthesis of polymers. In this study, biobased diamine was used as a chain extender of ester-urethane prepolymer. Obtained poly(ester-urethane-urea) contains 16 wt% of biobased diamine. There is mention of an...
-
The Effect of Cryogenic Treatment on Microstructure and Mechanical Response of AISI D3 Tool Steel Punches
PublicationRecently, deep cryogenic treatment is performed to improve the mechanical responses (wear, hardness, fatigue, and thermal conductivity) of various steel components. Researchers have tried to evaluate the eco-friendly and nontoxic process to optimize the parameters. Cold-shearing punches used to manufacture various holes that undergo severe impact loading and wear in the metal forming process. This study concerns the effect of soaking...
-
An Influence of Factors of Flow Condition, Particle and Material Properties on Slurry Erosion Resistance
PublicationThe degradation of materials due to slurry erosion is the serious problem which occurs in the power industries. The paper presents actual knowledge about an influence of individual factors connected with flow conditions, particles and material properties on the slurry erosion resistance. Among the factors connected with operating conditions, an influence of impact angle, and velocity of impact, particle concertation and liquid...
-
Quasistatic and fatigue behavior of an AISI H13 steel obtained by additive manufacturing and conventional method
PublicationThis work aims to compare the mechanical behavior of an AISI H13 steel obtained by additive manufacturing with that obtained by conventional manufacturing methods. The average values of the ultimate tensile strength (UTS) and ductility obtained for the specimens produced by the conventional method were equal to 658 MPa and 18%, respectively, which compares with 503 MPa and 0.75% registered for the selective laser melting (SLM)...
-
Non-linear behaviour of base-isolated building supported on flexible soil under damaging earthquakes
PublicationSeismic isolation is a strategy to reduce damage of structures exposed to devastating earthquake excitations. Isolation systems, applied at the base of buildings, lower the fundamental frequency of the structure below the range of dominant frequencies of the ground motion as well as allow to dissipate more energy during structural vibrations. The effectiveness of the base-isolated buildings in damage reduction has been confirmed...
-
Morphology and mechanical properties of polyamide/clay nanocomposites toughened with NBR/NBR-g-GMA: A comparative study
PublicationThis work highlights the importance of nanoclay dispersion state in the nanocomposites containing polyamide 6 (PA6), nanoclay and elastomers as well as clay localization at the interface of thermoplastic/elastomer. Morphology and mechanical properties of a series of nanocomposites containing acrylonitrile butadiene rubber (NBR), glycidyl methacrylate-grafted NBR (NBR-g-GMA), and combined NBR/NBR-g-GMA were compared and discussed...
-
Low-Temperature Requirements for Bitumen in Central East European Road Construction
PublicationThe paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....
-
A method of Functional Test interval selection with regards to Machinery and Economical aspects
PublicationThis paper discusses the problem of choosing the optimal frequency of functional test, including the reliability calculations and production efficiency, but also the effect of company risk management. The proof test as a part of the functional test interval is well described for the process industry. Unfortunately, this situation is not the case for the machinery safety functions with low demand mode. Afterwards, it is presented...
-
The innovative approach for using pavement as a fire prevention measure in tunnels
PublicationThe paper consists of two main parts: first presents study regarding the typically used pavement structures in tunnels and the second part: the first fire trials of the poroelastic SEPOR (Safe, Eco-friendly POroelastic Road Surface) mixture which was designed to be used among other uses in tunnels. In the first part of the paper different pavement materials, such as cement concrete, asphalt concrete, stone mastic asphalt and porous...
-
Ranking of ecotoxisity tests for underground water assessment using the Hasse diagram technique
PublicationThe present study deals with the novel application of the Hasse diagram technique (HDT) for the specific ranking of ecotoxicity tests capable of assessment of underground water quality. The area studied is a multi-municipal landfill in the northern Poland. The monitoring network of the landfill constitutes of 27 piezometers for underground water monitoring and two observation points at surface water courses. After sampling, chemical...
-
To what extent can hyperelastic models make sense the effect of clay surface treatment on the mechanical properties of elastomeric nanocomposites?
PublicationThe poor knowledge about nonlinear mechanical behavior of elastomer nanocomposites arises from the incomplete information on the interface. Application of hyperelastic models provides more insights into the nature and the situation of interaction between the elastomeric matrix and nanofillers. The current work seeks to address the effect of interphase strength on tensile properties of the elastomer nanocomposites under large deformations....
-
Influence of Laser Modification on the Surface Character of Biomaterials: Titanium and Its Alloys—A Review
PublicationLaser surface modification is a widely available and simple technique that can be applied to different types of materials. It has been shown that by using a laser heat source, reproducible surfaces can be obtained, which is particularly important when developing materials for medical applications. The laser modification of titanium and its alloys is advantageous due to the possibility of controlling selected parameters and properties...
-
Bio-Based Polyurethane Composites and Hybrid Composites Containing a New Type of Bio-Polyol and Addition of Natural and Synthetic Fibers
PublicationThis article describes how new bio-based polyol during the liquefaction process can be obtained. Selected polyol was tested in the production of polyurethane resins. Moreover, this research describes the process of manufacturing polyurethane materials and the impact of two different types of fibers—synthetic and natural (glass and sisal fibers)—on the properties of composites. The best properties were achieved at a reaction temperature...
-
Insights into Compatibilization of Poly(ε-caprolactone)-based Biocomposites with Diisocyanates as Modifiers of Cellulose Fillers
PublicationThis study aimed to analyze the impact of cellulose fillers’ modification with diisocyanates on the performance of composites based on the poly(ε-caprolactone) (PCL) matrix. Four most commonly used diisocyantes (isophorone, hexamethylene, toluene, and methylene diphenyl) were applied as modifiers of cellulose fillers (5 and 15 wt% per mass of filler). Modified fillers were introduced in the amount of 30 wt% into the PCL matrix....