Search
Search results for: INCREASE OF DURABILITY
-
ANALYSIS OF THE POSSIBILITIES OF HIGH SPEED SHAFT BEARING SYSTEM DURABILITY INCREASE
PublicationDuring the operation of wind turbines with a gearbox of traditional configuration, a high failure rate of high-speed shaft bearings is observed. Such a high failures frequency is not reflected in standard bearing durability calculation methods, which can be attributed to atypical failure mechanism. To avoid observed problems in the 1.5 MW wind turbine, the modification of the existing bearing system is proposed. Multiple options,...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublicationDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
The influence of applying supplementary web plates on structural joint moment resistance and rotational stiffness
PublicationContinual trend to simplify structural elements and find less time-consuming solutions on construction site as well as inevitable increase in labour costs determine for instance elimination of those technological steps that are difficult to automation. Welding additional reinforcements and web stiffeners is a great example of such a step. The method presented in EN 1993-1-8 [8] is a result of long-term studies focused on calculating...
-
Monitoring the curing process of epoxy adhesive using ultrasound and Lamb wave dispersion curves
PublicationMonitoring the stiffness of adhesives is a crucial issue when considering the durability andstrength of adhesive joints. While there are many studies conducted on specimens madeonly from adhesive, the problem of curing of an adhesive film in real joints is moderatelyconsidered. This paper presents the monitoring of stiffening of epoxy adhesive using ultra-sound. Ultrasonic pulse velocity method was firstly applied for monitoring...
-
Nowe możliwości generowania zarysów satelitowych mechanizmów roboczych
PublicationPlanetary hydraulic gear motors have been well known since 70's . first motors were constructed for maritime industry by hydroster from gdansk. the evolution of this type of motors led to an increase of nominal pressure and durability. nowadays the industry needs reliable and efficient motor able to work with alternative hydraulic fluids like water, emulsion and vegetable oil. therefore a new type of motors are being developed...
-
Pavement ageing influence on tyre/road noise
PublicationRoad surface should be constructed in a way that ensures safe and comfortable traffic conditions, not only when it is newly paved but also during its entire lifetime. An important factor in the asphalt mixture design process is also the expected pavement durability and stability of pavement properties over time. In many countries, road surface starts to play a significant role in traffic noise reduction actions. Selecting a particular...
-
Mathemathical model of radial passive magnetic bearing
PublicationIn the article mathematical radial model of passive magnetic bearings to ocean engineering units has been presented. The units application in underwater thrusters should increase propulsion systems durability and gives lower maintenance costs. The rotor of electric motor is hanging in magnetic field taken from radial passive magnetic bearings. However axial direction maintenance must be controlled with electromagnets and their...
-
Crack Resistance of Asphalt Concrete Subjected to Environmental Factors
PublicationThe paper presents an analysis of the influence of environmental factors on the cracking susceptibility of asphalt concrete resulting in a change in the durability of asphalt pavement. In order to assess the phenomenon, laboratory tests were carried out taking into account the destructive effects of moisture, freeze-thaw cycle and long-term ageing. The influence of both factors occurring simultaneously was also verified. Due to...
-
Wpływ zastosowania nakładek wzmacniających środnik na nośność i sztywność doczołowego węzła śrubowego.
PublicationCiągłe dążenie do upraszczania elementów konstrukcyjnych oraz znajdowania mniej czasochłonnych rozwiązań wykonawczo – montażowych wraz z nieuchronnym wzrostem kosztów robocizny determinują m.in. eliminację z procesów technologicznych tych etapów, które nie podlegają automatyzacji. Taką czynnością jest przede wszystkim spawanie dodatkowych wzmocnień i usztywnień węzłów w postaci żeber. Efektem wieloletnich badań jest metoda przedstawiona...
-
The potential of raw sewage sludge in construction industry – A review
PublicationExcess sewage sludge produced in any municipal or industrial wastewater treatment plant becomes a serious problem due to its increasing amount. This increase is related to the improvement of treatment technologies, expansion of sewage systems and the development of new industrial plants. The implementation and development of new technologies related to the utilization of sewage sludge is currently based on treating it as a substrate....
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublicationPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Mechanical, durability, depolluting and electrical properties of multifunctional mortars prepared with commercial or waste carbon-based fillers
PublicationCarbon-based fillers from industrial wastes and commercial ones were compared to improve the properties of lime-based mixes. As commercial fillers, graphene nanoplatelets and activated carbon were used, whereas as industrial wastes a char obtained by the gasification of biomasses and a used foundry sand were chosen. Carbon-based wastes were found to be a good cost-effective alternative to commercial carbon based fillers to increase...
-
Metodyka badań rozwojowych nowego typu silników i pomp satelitowych
PublicationResearch and development of new type satellite motors and satellite pumps SM with small geometrical displacement, from 5 to 73 cm3/rev, has been conducted in cooperation with Stosowanie Maszyn company from Katowice (manufacturer of motors and pump SM). The improvement of construction of those machines, especially construction of axial compensation and construction of fluid distribution channels have been the main problem of research...
-
LS-DYNA simulations of the impacts of a 38-ton Heavy Goods Vehicle into a road cable barrier
PublicationNowadays, more and more attention is being paid to safety on roads and motorways. It is due to the continuous development of road and motorway network and a significant increase of the number of vehicles on roads. To meet the expectations of improving road safety in Poland, the Road Innovations Development (RID) research programme was implemented in 2016. The aim of the RID 3A - Road Safety Equipment (RoSE) project is a comprehensive...
-
Tilting pad thrust bearing with novel material selection - experimental comparison of low and medium speed operation
PublicationThe advances in material engineering led to the development of hard carbon based coatings applied in numerous applications in order to prevent or minimize wear of the parts in contact. With Triondur® coatings, the bearing company Schaeffler has succeeded in halving the friction losses in the valve trains of passenger cars. The coatings are optimized for high abrasive wear protection and low sliding friction moments. Altogether...
-
THE INFLUENCE OF HOUSING ARRANGEMENT AND INTERFERENCE ON PRELOAD AND THEORETICAL LIFETIME OF A SYSTEM OF TAPER ROLLER BEARINGS OF A HIGH SPEED SHAFT OF A WIND TURBINE GEARBOX
PublicationA system of two taper roller bearings can carry loads with a high ratio of axial load to radial load. Such a system was proposed for a wind turbine gearbox following the poor durability of original bearing design with the aim of increasing durability. Because of size limits, a proposed system is composed of two different taper roller bearings. Standard manufacturers’ catalogues do not provide information on recommended preload...
-
Analiza porównawcza metod zwiększania nośności i sztywności stalowych, doczołowych węzłów śrubowych.
PublicationInnowacyjna, w porównaniu z dotychczas stosowanym sposobem, metoda obliczania nośności stalowych węzłów została wdrożona wraz z normami europejskimi. Pozwala ona dokładniej odwzo-rować rzeczywistą pracę poszczególnych części węzła, gdyż wynik obliczeń uzależniony jest od znacznie większej liczby zmiennych. Dzięki postępowi technologicznemu w zakresie metalurgii oraz badaniom naukowym obecnie możliwe jest wzmacnianie połączeń...
-
Seaweed utilization issues in biogas production
PublicationMacroalgae can be seen as a renewable feedstock for the production of biofuels in many coastal areas around the World and especially in Baltic Sea region where the eutrophication is particularly troublesome. The investigation of anaerobic digestion technologies for extracting inexhaustible bioenergy from seaweed was conducted in many research institutions mainly in laboratory scale. Although seaweeds seem to have a great potential...
-
FAILURE OF MAGNETIC FLUID SEALS OPERATING IN WATER: PRELIMINARY CONCLUSIONS
PublicationThe article analyses properties of magnetic fluid seals installed in rotary sealing no des which operate in the utility water environment. Seals of this type have been examined as a possible solution to the problem with ship manoeuvring propulsion sealing. The present analysis bases on laboratory durability tests of magnetic fluid seals expo sed to long - term utility water loads, at different water pressures and shaft revolutions....
-
Testing the durability and function of road traffic management devices
PublicationTraffic management measures (vertical signs and horizontal marking, reflective elements) are used for guiding vehicles optically, indicating road mileage, marking objects in road gauge, marking vehicle and pedestrian safeguards and driver information and warning. This paper presents a synthesis of a literature study and the results of research conducted under stage one of the project LifeRoSE. The requirements for different traffic...
-
On the durability of the hydraulic satellite motor working mechanism in overload condition
PublicationThe paper presents the newest construction of the hydraulic satellite pump/motor. In this study, the fracture of the hydraulic satellite motor working mechanism is investigated. Factors influencing the durability of satellite working mechanism have been described. The durability of the hydraulic satellite motor working mechanism at a load, corresponding to a pressure of 15 MPa supplied with refined rapeseed oil is very low. Analyses...
-
Analiza trwałości zmęczeniowej asfaltów drogowych i modyfikowanych z wykorzystaniem testu liniowego zwiększania amplitudy / Analysis of the fatigue life of neat and modified bitumens using linear amplitude sweep test
PublicationThe paper presents an evaluation of the fatigue resistance of selected Polish bituminous binders: neat bitumen 50/70, polymer modified bitumen PMB 45/80-55 and polymer highly modified bitumen PMB 45/80-80. The linear amplitude sweep (LAS) test, which is a new bitumen performance grading test developed in the USA, and was used to assess the fatigue life of the bitumens. Highly modified bitumen 45/80-80 showed 10-20 times higher...
-
Influence of local bush wear on water lubricated sliding bearing load carrying capacity
PublicationOne of main problems concerning water-lubricated bearings is their durability. There are known cases of bearings with life time measured in decades, and some, whose refurbishment was necessary just days after start-up. Obtaining stable fluid film friction plays key role in the durability of these bearings. Unfortunately, their load-carrying capacity is limited due to water's low-viscosity. The conducted experimental...
-
THE DETERMINATION OF ABRASION RESISTANCE OF SELECTED BIOMATERIALS FOR THE FRICTION PAIRS IN THE HIP JOINT ENDOPROSTHESIS
PublicationThe key requirement for the modern endoprosthesis is high durability of the friction components, which results in long and trouble-free operation in the human body. The durability of currently used endoprosthesis is often limited by tribological wear processes of friction components (e.g. between the head and the acetabular component in a hip joint endoprosthesis) [8, 19, 23, 24]. In order to compare the tribological wear, tribological...
-
Reliability model of the crankshaft-piston assembly
PublicationThe laws that govern the durability of crankshaft-piston assembly friction nodes can be proved or at least derived or justified in an intuitive way. Operation of all the friction nodes is disturbed by external factors occurring with randomly changing intensity and also appearing at random. As the crankshaft-piston assembly friction nodes have a series structure and effects of those disturbances accumulate, their fitness for use...
-
CAPABILITY OF IDENTIFYING AND PREDICTING THE TECHNICAL CONDITION OF PLATE HEAT EXCHANGERS IN OPERATION
PublicationThe paper presents a test stand for plate heat exchangers, allowing to identify the technical condition and to predict durability of the heat exchangers used aboard the sea-going ships: ”Oceanograf”, ”Władysław Orkan”and a passenger-car ferry, under the condition that they are of the same type and manufactured by the same company. In the first part three different installations with plate heat exchangers in the engine rooms...
-
Assessment of the application of CEM III with exposed aggregate as an alternative to CEM I for road pavements
PublicationThe article presents a results of study on the impact of replacing CEM I SR3/NA by CEMIII/A LH/HSR/NAon the mechanical properties and durability of pavement concrete with exposed aggregate. Was used granite aggregate and washed sand. Water/cement () ratio in the tested concretes constituted 0.35 and 0.4 and part of the cement was replaced with a 5% addition of natural pozzolana – zeolite. Compressive strength tests were performed...
-
Experimental research on marine oil-lubricated stern tube bearing
PublicationBearings of propeller shafts are very crucial elements of the propulsion system of each of the ships. The safety of shipping depends on their durability and reliability. The new legal restrictions mean that today we are looking for environmentally friendly solutions. That is why water-lubricated bearings are becoming more and more popular. So, will oil-lubricated shaft bearings belong to the past? The bearing with a white metal...
-
Insight into the microstructural and durability characteristics of 3D printed concrete: Cast versus printed specimens
PublicationThis study presents the comparison of microstructural and durability characteristics of 3D printed concrete (3DPC) depending on its production method (printing or casting). Printed samples with different numbers of layers, as well as a cast specimen with an identical mix composition, were produced and compared, with their microstructural pore and solid characteristics quantitatively and qualitatively investigated. For this purpose,...
-
An experimental study of self-sensing concrete enhanced with multi-wall carbon nanotubes in wedge splitting test and DIC
PublicationConcrete is the worldwide most utilized construction material because of its very good performance, forming ability, long-term durability, and low costs. Concrete is a brittle material prone to cracking. Extensive cracking may impact durability and performance over time considerably. The addition of a small amount of carbon nanotubes (CNT) increases the concrete’s overall electrical conductivity, enabling internal structure...
-
Influence of operating pressure on the durability of a satellite hydraulic motor supplied by rapeseed oil
PublicationThis article describes the results of a durability test of a hydraulic satellite motor supplied by rapeseed oil. The tests were carried out on a test stand in a power recuperation system. The tests of the motor were carried out at a constant shaft speed for three fixed pressure drops in the motor. This made it possible to demonstrate the influence of the motor operating pressure on the durability of the satellite mechanism. The...
-
Corrosion of AISI1018 and AISI304 steel exposed to sulfates
PublicationThis research analyses the behavior of corrosion, durability, and quality of reinforced concrete samples coated with two different materials when exposed to contaminated soil with sulfates. The initial assessment involved evaluating the water absorption rate of the coating materials before and after exposure to a solution containing 3%푁푎2푆푂4+3%푀푔푆푂4+3%퐾2푆푂4+3%퐶푎푆푂4to determine their durability. the corrosion...
-
Method for prediction of the frost resistance ability of air‐entrained concrete based on the 3D air void characteristics by x‐ray micro‐CT
PublicationIn modern construction, one of the most important factors in the execution of contracts is time. Standard procedures for assessing the frost resistance or concrete are usually very time-consuming and can take up to 40 days. The current paper is experimentally and practically oriented. It presents an alternative testing method, based on air void network, that allows to assess the frost resistance of concrete within just a few days...
-
NON-LOCAL VOLUMETRIC APPROACH TO ANALYSIS DEFECT'S SHAPE INFLUENCE ON SPECIMENS DURABILITY SUBJECTED TO BENDING AND TORSION
PublicationThe influence of defect features on fatigue behaviour is a complex trivial issue. Although the important advances over the last decades, the dialectical relationship between the defect orientation and durability is not clearly understood. The paper aims at studying the influence of the orientation of elliptical defects on the durability of samples made of C45 steel. Three types of samples with elliptical defects were subjected...
-
Effectiveness of various types of coating materials applied in reinforced concrete exposed to freeze–thaw cycles and chlorides
PublicationThis study assesses the durability of coated and uncoated concrete surfaces protected with four different coating materials: water-soluble (BW), solvent-based (BR), mineral (MI), and epoxy (EP). The durability assessment includes evaluating the absorption rate of water, pull-off adhesion strength, and coating material thickness. Concrete samples were subjected to immersion in regular water and a 7% urea solution, followed by...
-
Effectiveness of various types of coating materials applied in reinforced concrete exposed to freeze–thaw cycles and chlorides
PublicationThis study assesses the durability of coated and uncoated concrete surfaces protected with four Different coating materials: water-soluble (BW), solvent-based (BR), mineral (MI), and epoxy (EP). The durability assessment includes evaluating the absorption rate of water, pull-of adhesion strength, and coating material thickness. Concrete samples were subjected to immersion in regular water and a 7% urea solution, followed by cyclic...
-
Application of the LifeRoSE method in funcionality evaluation of road safety equipment
PublicationThe article presents a mathematical model of the life cycle estimation method of road safety equipment. Then the model was adjusted to estimate the life cycle costs of the chosen horizontal road marking. Using the LCC method, the functionality of the horizontal marking was evaluated in terms of efficiency, durability and economic effectiveness. The article also presents the impact of selected factors on the life cycle costs of...
-
Influence of Rock Dust Additives as Fine Aggregate Replacement on Properties of Cement Composites—A Review
PublicationConcrete production consumes enormous amounts of fossil fuels, raw materials, and is energy intensive. Therefore, scientific research is being conducted worldwide regarding the possibility of using by-products in the production of concrete. The objective is not only to identify substitutes for cement clinker, but also to identify materials that can be used as aggregate in mortar and concrete productions. Among the potential alternative...
-
Durability evaluation of technical fabrics
PublicationA thorough examination of the influence of the conditions of use on the mechanical properties of technical fabrics is proposed. Laboratory experiments (uniaxial tensile, rheological, cyclic and biaxial tensile tests) have been conducted and the material’s parameters for Finite Element Method (FEM) simulations have been identified. Various constitutive models of technical fabrics are investigated and compared. On the basis of these...
-
Diagnostic Model of Crankshaft Seals
PublicationT he paper presents a research stand being a diagnostic model of radial lip seals used, among others, on crankshafts of piston combustion engines in order to identify the correctness of their operation. The possibility of determining the technical condition of lip seals on the basis of the proposed coefficient of correctness of operation has been described. T he basic features of seals influencing their correctness of...
-
Properties of Old Concrete Built in the Former Leipziger Palace
PublicationThis research aims to determine the mechanical, chemical, and physical properties of old concrete used in the former Leipziger Palace in Wrocław, Poland. The cylindrical specimens were taken from the basement concrete walls using a concrete core borehole diamond drill machine. The determination of the durability and strength of old concrete was based on specified chosen properties of the old concrete obtained through the following...
-
Effect of elliptical defect orientation on the durability of specimens subjected to cyclic bending
PublicationThis work presents the effect of elliptical defects orientation on the durability of specimens made of C45 steel. Three kinds of specimens with elliptical defects in the form of a one-sided notch oriented at different angles 45, 60, and 90 degrees were subjected to cyclic bending (R=-1). The stress state analysis was performed using local and non-local methods to determine an equivalent amplitude of stress, and then the results...
-
Bitumen-Based Poroelastic Pavements: Successful Improvements and Remaining Issues
PublicationThis article presents the development process of designing and testing poroelastic pavement based on highly polymer-modified bitumen. Poroelastic wearing course was composed of mineral and rubber aggregate mixed with highly polymer-modified bitumen, in contrast to previous trials, during which polyurethane resins were mainly used as binder, which led to several serious technological problems concerning difficult production, insufficient...
-
The oil film parameters of the wankel engine apex seal in aspects of durability of mating elements
PublicationThe Wankel engine is one of only few alternatives to the reciprocating engines. The advantages such as good value of maximum engine power to its mass ratio are still present and can have great sense in selected fields of application, for example General Aviation. Nevertheless the disadvantages of the Wankel engine design have never lost its importance and still pose an obstacle to wider use of the Wankel engine. One of the main...
-
TECHNOLOGY OF CREATING AND USAGE OF PROECOLOGICAL BLOCK EMPTYSEED
PublicationNowadays, finding natural substitutes for mass-produced materials is one of the main tasks faced by scientists and designers. There is an increasing emphasis on the theme of ecology and the need for sustainability. Variants and methods are sought which will create environmentally friendly materials in a fast, relatively inexpensive and ecological way. The aim of this paper is to present different proposals of natural building materials...
-
The use of a 4 PB strain sweep fatigue test to evaluate characteristics of carbon grid reinforced asphalt beams
PublicationThe article presents research results concerning pre-bituminized carbon grids for asphalt pavement reinforcement, which are used to prevent cracking and crack reflection thus increasing bearing capacity and durability of pavement. Research program involved testing of large sized double-layer samples, both reinforced and unreinforced. The advantage of using a carbon grid was especially visible after crack initiation. The energy...
-
Lightweight structures in architecture: scenarios for the future
PublicationLightweight structures - structures with a reduced weight, which otherwise retain the qualities necessary for the building performance, ensuring a proper durability and strength, safety, indoor environmental quality and energy efficiency; stuctures which strive for the optimization of structural systems - are in tune with current trends and socio-economic, environmental and technological factors. The growing interest in the lightweight...
-
Micro- and nano-Illite to improve strength of untreated-soil as a nano soil-improvement (NSI) technique
PublicationSoil stabilization is a technique of improving the geotechnical properties of soils for various engineering applications. However, conventional stabilizers such as cement and lime have some limitations, such as high cost, environmental impact, and durability issues. Therefore, there is a need for alternative and innovative stabilizers that can overcome these challenges. This study introduces nano-Illite, a type of clay mineral,...
-
Poroelastic Material for Urban Roads Wearing Courses
PublicationConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
N-doped carbon materials as electrodes for highly stable supercapacitors
PublicationThis article reports a strategy to use nitrogen-doped carbon materials as electrodes for supercapacitors. Depending on the carbon precursor, the porous structure is changed with specific surface area reached up to 2270 m2 g−1. The capacitance of carbon materials used as electrodes is related strictly to pore size. The microstructure and nitrogen functionalities enable a high capacitance (327 F g−1) and cycle durability. The nanoporous...