Search
Search results for: MONEY ENERGY TRUST UNIVERSAL EQUIVALENT
-
The energy concept of money
PublicationPurpose: This paper aims to provide the literature review seeking an answer whether energy can be used as a universal equivalent instead of money. Methodology: The author conducted a review of available literature and data sources related to the money theory and energy concept of money. Findings: It was found that the definition of energy as a general equivalent has a contextual and dynamic nature, and this field’s consolidation...
-
Determination of equivalent axle load factors with the use of strain energy of distortion
PublicationThe paper proposes a new method for calculation of equivalent axle load factors based on the analysis of strain energy of distortion induced in road pavements by traffic loads. The main advantage of the method is the more accurate calculation of the effects of multiple axles and super single versus dual tyres. The methodconsiders the location of critical points, at which strain energy of distortion reaches extreme values. When...
-
A universal NDT method for examination of low energy impact damage in CFRP with the use of TLC film
PublicationThe article presents an attempt to use a sheet of laminated thermochromic liquid crystal film (TLC film) for non-destructive testing of the impact damage (energy values: 1J, 2J, 3J and 4J) in carbon fibre-reinforced polymer (CFRP). This is a new, alternative NDT approach based on the thermo-optical effect. The main advantages of this method are a) the low cost of TLC film, b) the low cost of recording devices due to the usage of...
-
Toward a universal Embedded-Atom Method: II. A set of transferable denisty and dimmer referenced embedding energy functions for all elements of the periodic table as tool for removing two gauge degrees of freedom in EAM potentials
PublicationZestaw kluczowych właściwości homodwuatomowych cząsteczek o Z ≤ 103 (równowagowa odległość między atomami re, energia dysocjacji DO, Liczba falowa drgań ωe) zostały zestawione na bazie dostępnych danych eksperymantalnych oraz obliczeń za pomocą teorii funkcjonałów gęstości elektronowej B3LYP/SBKJC.
-
Magdalena Szuflita-Żurawska
PeopleHead of the Scientific and Technical Information Services at the Gdansk University of Technology Library and the Leader of the Open Science Competence Center. She is also a Plenipotentiary of the Rector of the Gdańsk University of Technology for open science. She is a PhD Candidate. Her main areas of research and interests include research productivity, motivation, management of HEs, Open Access, Open Research Data, information...
-
PAYMENT TRANSACTIONS’ ENERGY EFFICIENCY
PublicationThe payment system and infrastructure is a sector that is not given enough attention today in the context of energy efficiency. This sector plays a big role in organizing and ensuring money circulation and funds. It has its value consisting on the one hand of the cost of payment equipment, infrastructure, payment instruments. On other hand, its value consists of the cost of energy for their manufacture and maintenance. The European...
-
Kontekstowo zorientowany model bezpieczeństwa systemów internetowych
PublicationW rozprawie dokonano analizy usługowych systemów internetowych pod względem bezpieczeństwa. Przedstawiono autorskie uniwersalne modele bezpieczeństwa CoRBAC oraz jego rozszerzenie TCoRBAC, będące rozwinięciem tradycyjnego modelu RBAC. Uwzględniono analizę szeroko rozumianego kontekstu funkcjonowania systemu oraz poziom jego zaufania do użytkownika. Opracowano metodę wyznaczania dwóch parametrów: zaufania do systemu (λ) będącego...
-
Energy Losses Due to Imperfect Payment Infrastructure and Payment Instruments
PublicationOne of the strategic objectives of the European Union is a reduction in greenhouse gas emissions and improvement of energy efficiency by at least 32.5% in different areas of the economy by 2030. However, little is known about the impact of payment in retail on energy consumption. The purpose of this paper is to assess the chain of losses of time and energy, and therefore financial losses, that occur due to the imperfection of payment...
-
Low energy electron mass stopping power in H2
PublicationWe present experimental mass stopping powers of electrons in gaseous H2 obtained with a newly developed electron time-of-flight spectrometer, for the incident electron energy range of 10eV to 25eV. In our procedure the average energy loss is derived from our conversion of measured electron time-of-flight spectra into equivalent electron energy loss spectra so as to obtain the values of mass stopping power for electron scattering...
-
The Energy of Finance in Refining of Medical Surge Capacity
PublicationThe availability of resources and their concentration in the place of greatest need, will not allow us to successfully overcome a medical surge without the energy required to activate these resources and activities, and increase their quantities if necessary, that is why the staff and management of healthcare institutions are forced to making ethical crisis decisions about who wins and who loses. This study highlights the versatility...
-
Zarządzanie zaufaniem w bezprzewodowych sieciach czujników - studium przypadku
PublicationW artykule przedstawiono studium przypadku dotyczące zastosowania bezprzewodowej sieci czujników do wspomagania pacjenta z nadwagą w jego środowisku domowym. Przyjęto, że sieć wykorzystuje metodę rozproszonego zarządzania zaufaniem i pokazano, że metoda ta umożliwia wykrycie i izolację czujników realizujących działania sprzeczne z polityką sieci. Ilościowe oszacowanie czasu niezbędnego do wykrycia takich...
-
Feasibility Study of Three-Phase Modular Converter for Dual-Purpose Application in DC and AC Microgrids
PublicationThe modern concept of a universal converter is intended as a power converter suitable for application in both dc or ac grids using the same external connectors. This novel family was recently proposed to allow an easier integration of renewable energy sources and energy storage systems, interfacing with dc/ac grids and/or loads with a minimum redundancy of power switches and passive elements. This kind of solution and applications...
-
Feasibility Study of Three-Phase Modular Converter for Dual-Purpose Application in DC and AC Microgrids
PublicationThe modern concept of a universal converter is intended as a power converter (PC) suitable for application in both dc or ac grids using the same external connectors. This novel family was recently proposed to allow easier integration of renewable energy sources and energy storage systems (ESSs), interfacing with dc/ac grids and/or loads with a minimum redundancy of power switches and passive elements. This kind of solution and...
-
Experimental determination of H2 mass stopping powers for low-energy electrons
PublicationWe present experimental mass stopping powers of electrons in gaseous H2 obtained with an electron time- of-flight spectrometer, for the incident electron energy range of 11 to 25 eV. In our procedure, the average energy loss is derived from conversion of the measured electron time-of-flight spectra into equivalent electron energy-loss spectra. Our present results are compared with the only available experimental measurement and...
-
Constant vs. Variable Efficiency of Electric Drive in Train Run Simulations
PublicationTrain run simulations, which focus on various power- and energy-oriented aspects, should reflect the losses in the electric powertrain. In general, the powertrain efficiency varies with respect to load and speed. Including this relation in simulation requires knowledge about detailed drivetrain parameters, which are often unavailable. This paper verifies the possibility to approximate the drivetrain efficiency in train run simulations...
-
Reducing Air Pollutant Emissions from the Residential Sector by Switching to Alternative Energy Sources in Single-Family Homes
PublicationThe paper discusses a scenario for adapting residential buildings to the requirements of the EU climate and energy package. It analyzes the option of reducing pollutant emissions to ambient air by switching to alternative energy sources in a typical single-family residential building. The most common sources of energy in central heating and ventilation systems and water heating systems were compared, and the analyzed energy carriers...
-
Balancing Energy Inputs/Outputs and GHG Emissions for Sustainable Wastewater Treatment – a Case Study
PublicationThe aim of the study is a model-based evaluation of the selected operating modes and technological upgrades on the energy balance and greenhouse gas (GHG) emissions in a large wastewater treatment plant in the city of Slupsk (northern Poland). The considered scenarios focus on energy savings for aeration, increasing energy recovery via biogas cogeneration and reduction of the CO2 equivalent emission from both direct processes (related...
-
The process generation of WWTP models for optimization of activated sludge systems
PublicationThe objective of water and wastewater utilities, which are responsible for optimization of wastewater treatment plant operation, is threefold: environmental protection, saving money, and mitigation of pollutant emissions, both to water and air. The performed study aimed to assess the process generation of WWTP models that improve activated sludge systems operation, by means of new developed Mantis2 model. This model accounts for...
-
Low-Power WSN System for Honey Bee Monitoring
PublicationThe paper presents a universal low-power system for biosensory data acquisition in scope of bees monitoring. We describe the architecture of the system, energy-saving components as well as we discuss the selection of used sensors. The work focuses on energy optimization in a scope of wireless communication. A custom protocol was implemented, which is the basis for presented energy-efficient devices. Data exchange process during...
-
Energy neutrality versus carbon footprint minimization in municipal wastewater treatment plants
PublicationThis work aimed to compare the carbon footprint (CF) of six full-scale wastewater treatment plants (WWTPs). The CF was estimated in the range of 23–100 kg CO2e per population equivalent. In the total CF, the direct emissions held the highest share (62–74%) for the plants with energy recovery from biogas. In the plants depending entirely on the power grid, the indirect emissions due to energy consumption dominated the total CF (69–72%)....
-
Marek Czachor prof. dr hab.
People -
Immittance Studies of Bi6Fe2Ti3O18 Ceramics
PublicationResults of studies focusing on the electric behavior of Bi6Fe2Ti3O18 (BFTO) ceramics are reported. BFTO ceramics were fabricated by solid state reaction methods. The simple oxides Bi2O3, TiO2, and Fe2O3 were used as starting materials. Immittance spectroscopy was chosen as a method to characterize electric and dielectric properties of polycrystalline ceramics. The experimental data were measured in the frequency range D = (101–107)...
-
Microstructure and Dielectric Properties of Barium-vanadate Glasses
PublicationThe ac and dc conductivity in barium-vanadate glasses was investigated as a function of temperature and frequency with the use of impedance spectroscopy. The topography and microstructure of glasses were investigated by the means of X-ray diffraction (XRD) and scanning electron microscopy (SEM) methods. The XRD results show that all samples are amorphous but microscopy investigation reveals that glasses with greater amount of V2O5...
-
DETERMINANTS OF INLAND NAVIGATION ON THE VISTULA FROM WARSAW TO GDAŃSK
PublicationWaterborne transport is the cheapest, the safest and the least harmful to the natural environment. Restoring regular waterway cargo transport will require revitalisation of the existing trans-shipment and logistics infrastructure for commercial inland ports and building new. Transport policy makers must remember that waterborne transport is the most ecological type of transport. It produces only 10% of the gases emitted to the...
-
Mechanism of hopping conduction in Be–Fe–Al–Te–O semiconducting glasses and glass–ceramics
PublicationElectrical properties of beryllium-alumino-tellurite glasses and glass–ceramics doped with iron ions were studied using impedance spectroscopy. The conductivity was measured over a wide frequency range from 10 mHz to 1 MHz and the temperature range from 213 to 473 K. The D.C. conductivity values showed a correlation with the Fe-ion concentration and ratio of iron ions on different valence states in the samples. On the basis of...
-
Comparison of different one-parameter damage laws and local stress-strain approaches in multiaxial fatigue life assessment of notched components
PublicationThis paper aims to compare the predictive capabilities of different one-parameter damage laws and local stress-strain approaches to assess the fatigue lifetime in notched components subjected to proportional bending-torsion loading. The tested fatigue damage parameters are defined using well-known stress-based, strain-based, SWT-based and energy-based relationships. Multiaxial cyclic plasticity at the notch-controlled process zone...
-
Machine learning for the management of biochar yield and properties of biomass sources for sustainable energy
PublicationBiochar is emerging as a potential solution for biomass conversion to meet the ever increasing demand for sustainable energy. Efficient management systems are needed in order to exploit fully the potential of biochar. Modern machine learning (ML) techniques, and in particular ensemble approaches and explainable AI methods, are valuable for forecasting the properties and efficiency of biochar properly. Machine-learning-based forecasts,...
-
Polynomial description of dynamic impedance spectrogram—introduction to a new impedance analysis method
PublicationThis paper presents a polynomial description of spectrograms obtained using Dynamic Electrochemical Impedance Spectroscopy. A method to fit the polynomial degree correctly is discussed. A simple electrical system of a diode connected in parallel with a capacitor was used for testing. Dynamic impedance measurements during potentiodynamic polarization were conducted. This paper presents an alternative analysis method that allows...
-
Investigation on Mode I Fracture Behavior of Hybrid Fiber-Reinforced Geopolymer Composites
PublicationRecent reports in the literature have shown that fber-reinforced geopolymer composites (FRGC) made with monofbers exhibit a signifcant enhancement in fracture energy. However, many aspects of the fracture performance of hybrid fberreinforced geopolymer composites (HFRGC) remain largely unexploited, and these are predominant for the structures. For the frst time, the mode I fracture energy of HFRGC is investigated. The mode I behavior...
-
Leveraging food waste for electricity: A low-carbon approach in energy sector for mitigating climate change and achieving net zero emission in Hong Kong (China)
PublicationIn recent years, food waste has been a global concern that contributes to climate change. To deal with the rising impacts of climate change, in Hong Kong, food waste is converted into electricity in the framework of low-carbon approach. This work provides an overview of the conversion of food waste into electricity to achieve carbon neutrality. The production of methane and electricity from waste-to-energy (WTE) conversion are...
-
Influence of Thermal Decomposition of Wood and Wood-Based Materials on the State of the Atmospheric Air. Emissions of Toxic Compounds and Greenhouse Gases
PublicationThis paper presents the energy characteristics of wood and wood-based materials in the form of commercially available pellets, furniture board (MDF) and OSB. Toxicometric indices were determined for gaseous destructs arising from thermal decomposition and combustion of the materials studied. The paper proves that combustion conditions are crucial in terms of toxic destructive emissions. It has been shown that the combustion of...
-
Low cost set-up for supercapacitors parameters evaluation
PublicationSupercapacitors are capable to store relatively high amount of energy comparing to its mass. Growing number of these devices applications requires development of new testing methods. Standard methods of evaluation of supercapacitor parameters, as cycling voltammetry, CV, galvanostatic cycling with potential limitation, GCPL, impedance measurements, require equipment of high cost...
-
Neoclassical Navier–Stokes Equations Considering the Gyftopoulos–Beretta Exposition of Thermodynamics
PublicationThe seminal Navier-Stokes equations were stated even before the creation of the foundations of thermodynamics and its first and second laws. There is a widespread opinion in the literature on thermodynamic cycles that the Navier-Stokes equations cannot be taken as a thermodynamically correct model of a local "working fluid", which would be able to describe the conversion of "heating" into "working" (Carnot's type cycles) and vice...
-
The community involvement of courts: an action research study in the context of the Polish justice system
PublicationPurpose – As a rule, common courts are hermetic organizations, separated from their stakeholders by procedures based on legal provisions. For these reasons, they are often perceived as unreliable and non-transparent, and as such, they do not inspire trust among stakeholders. The authors posit that the court’s community involvement may lead to the increased accountability and legitimacy of courts, which should in turn result in...
-
The assessment of solar photovoltaic in Poland: the photovoltaics potential, perspectives and development
PublicationThe following article explains the current condition of the photovoltaics sector both in Poland and worldwide. Recently, a rapid development of solar energy has been observed in Poland and is estimated that the country now has about 700,000 photovoltaics prosumers. In October 2021, the total photovoltaics power in Poland amounted to nearly 5.7 GW. The calculated technical potential of photovoltaics in Poland is 153.484 PJ (42.634...
-
Design of residential buildings in architecture education
PublicationThis article is based on an analysis of residential building designs made by students of the Faculty of Architecture at Gdańsk University of Technology (FA-GUT), Poland, and on the results of a survey conducted among these students. The purpose of the survey was to verify the broad, interdisciplinary knowledge of the students required in preparation for taking up design issues, as well as their ability to use this knowledge in...
-
Information transfer during the universal gravitational decoherence
PublicationRecently Pikovski et al. (Nat Phys 11:668, 2015) have proposed in an intriguing universal decoherence mechanism, suggesting that gravitation may play a conceptually important role in the quantum-to-classical transition, albeit vanishingly small in everyday situations. Here we analyze information transfer induced by this mechanism. We show that generically on short time-scales, gravitational decoherence leads to a redundant information...
-
Low-Cost Automated Design of Compact Branch-Line Couplers
PublicationBranch-line couplers (BLCs) are important components of wireless communication systems. Conventional BLCs are often characterized by large footprints which make miniaturization an important prerequisite for their application in modern devices. State-of-the-art approaches to design of compact BLCs are largely based on the use of high-permittivity substrates and multi-layer topologies. Alternative methods involve replacement of transmission-line...
-
Low-energy positron collisions with water: elastic and rotationally inelastic scattering
PublicationDifferential, integral and momentum transfer cross sections for the vibrationally elastic and rotationally inelastic scattering of positrons from water at low collision energy (E ≤ 10 eV) are reported. Several models within the R-matrix method are used to compute the body-fixed T-matrices, while the scattering calculations are performed within the fixed-nuclei approximation corrected with the standard Born-closure formula. These...
-
Long-distance quantum communication over noisy networks without long-time quantum memory
PublicationThe problem of sharing entanglement over large distances is crucial for implementations of quantum cryptography. A possible scheme for long-distance entanglement sharing and quantum communication exploits networks whose nodes share Einstein-Podolsky-Rosen (EPR) pairs. In Perseguers et al. [Phys. Rev. A 78, 062324 (2008)] the authors put forward an important isomorphism between storing quantum information in a dimension D and transmission...
-
Eksperymentalna analiza współczynników oporów lokalnych dla wybranych kształtek i złączek w systemach rur wielowarstwowych
PublicationArtykuł poświęcony jest analizie wartości współczynników oporów lokalnych dla wybranych kształtek i złączek pracujących w instalacjach z rur wielowarstwowych z tworzyw sztucznych. Badaniom poddano elementy o średnicach DN16, DN20, DN25, powszechnie wykorzystywane we współczesnych instalacjach sanitarnych. W pracy przedstawiono wybrane wyniki badań laboratoryjnych (dla rozszerzeń, kolanek i trójników) oraz ich porównanie z wartościami...
-
Factors of successful client co-production in knowledge-intensive business services
PublicationPurpose This paper aims to explore the topic of client co-production in knowledge-intensive business services (KIBS). The paper first sketches a theoretical background and reviews previous studies on factors affecting successful client co-production in such companies and then examines these factors via case study research among a small KIBS company and its five customers. Design/methodology/approach The paper is based on an in-depth...
-
Client co-production in knowledge-intensive business services (KIBS): Case study analysis
PublicationPurpose: This paper aims to explore the topic of client co-production in knowledge-intensive business services (KIBS). The paper first sketches a theoretical background and reviews previous studies on factors affecting successful client co-production in such companies and then examines these factors via case study research among a small KIBS company and its five customers. Methodology: The paper is based on an in-depth analysis...
-
Tensile failure study of 3D printed PLA using DIC technique and FEM analysis
PublicationThe paper presents the experimental and numerical study of the failure behaviour of Fused Filament Fabricated (FFF) Polylactic Acid (PLA) samples subjected to tensile load. The examined samples are printed in flat orientation with 0◦, 45◦ and 90◦ raster angles. During the experiments the deformation of the specimens is continuously scanned with the 3D Aramis measuring system utilizing the digital imaging correlation technique,...
-
Management and economic of engineer projects
e-Learning CoursesLectures - 05 October-30 November, 2023 1. Project management: Engineers, projects, management, planning and scheduling, personnel and organizational, team building, project control, estimating and ordering. 2. Team building: personality types, team effectiveness. 3. Project management: WBS, Gantt, Earned Value Method, critical path, risk management. 4. Economic Engineering: Establishing economic equivalence, Interest: cost...
-
Reduced-Cost Design Optimization of High-Frequency Structures Using Adaptive Jacobian Updates
PublicationElectromagnetic (EM) analysis is the primary tool utilized in the design of high-frequency structures. In vast majority of cases, simpler models (e.g., equivalent networks or analytical ones) are either not available or lack accuracy: they can only be used to yield initial designs that need to be further tuned. Consequently, EM-driven adjustment of geometry and/or material parameters of microwave and antenna components is a necessary...
-
Comprehensive evaluation of the carbon footprint components of wastewater treatment plants located in the Baltic Sea region
PublicationFinland and Poland share similar environmental interests with regard to their wastewater effluents eventually being discharged to the Baltic Sea. However, differences in the influent wastewater characteristics, treatment processes, operational conditions, and carbon intensities of energy mixes in both countries make these two countries interesting for carbon footprint (CF) comparison. This study aimed at proposing a functional...
-
Low-Cost Design Optimization of Microwave Passives Using Multi-Fidelity EM Simulations and Selective Broyden Updates
PublicationGeometry parameters of contemporary microwave passives have to be carefully tuned in the final stages of their design process to ensure the best possible performance. For reliability reasons, the tuning has to be to be carried out at the level of full-wave electromagnetic (EM) simulations. This is because traditional modeling methods are incapable of quantifying certain phenomena that may affect operation and performance of these...
-
Cichy sonar - stan aktualny i perspektywy
PublicationW zastosowaniach militarnych często istnieje potrzeba prowadzenia obserwacji w sposób skryty za pomocą urządzeń emitujących sygnały trudne do przechwycenia przez przeciwnika. Rozwiązania stosowane w cichych radarach stanowiły punkt wyjścia do opracowania cichego sonaru. Prace nad projektem rozpoczęto na Politechnice Gdańskiej w roku 2010 w ramach Grantu NCBiR i są one dalej kontynuowane. W celu zachowania w cichym sonarze warunków...
-
Nanotechnologia w architekturze – korzyści i problemy wynikające z zastosowania nanotechnologii w aspekcie cyklu życia budynku
PublicationDynamiczny rozwój technologii zawsze odgrywał ważną rolę w procesie kształtowania architektury. Postęp w dziedzinie inżynierii materiałowej już od Rewolucji Przemysłowej pozwalał na osiąganie co raz bardziej skomplikowanych i jednocześnie wytrzymałych konstrukcji budynków. Obecnie, w dziedzinie architektury, zaczyna pojawiać się pojęcie nanotechnologii, która pozwala zmieniać stosowane materiały w bardziej wydajne i odporne....