Filters
total: 2283
filtered: 1620
displaying 1000 best results Help
Search results for: ATMOSPHERIC CIRCULATIONS
-
EXPERIMENTAL VERIFICATION OF THE METHOD OF FLOW BOILING AND FLOW CONDENSATION HEAT TRANSFER PREDICTION FOR SELECTED FLUIDS
PublicationIn the paper presented are the results of calculations using authors own model to predict heat transfer coefficient during flow boiling of different refrigerants. The experimental data from various research studies from literature were collected. Calculations were conducted for a full range of quality variation and a wide range of mass velocity. The aim of the study was to test the sensitivity of the in- house developed model....
-
Electrical properties of Y0.08Sr0.92Ti0.92Nb0.08O3-δ after reduction in different reducing conditions
PublicationElectrical properties of perovskite Y0.08Sr0.92Ti0.92Nb0.08O3−ı after reduction in different conditions were studied. Relatively high electrical conductivity in samples reduced in ammonia was observed. The conductivity of Y0.08Sr0.92Ti0.92Nb0.08O3−ı reduced in ammonia at 1500 ◦C was of about 600 S/cm at 200 ◦C. Conductivity after reduction in ammonia at 1500 ◦C was stable both in hydrogen and oxygen atmosphere up to 600 ◦C. Reduction...
-
Hydropower potential of the lower Vistula
PublicationThis paper presents an estimate analysis of the hydropower potential of the lower Vistula River from Warsaw to Gdańsk Bay. The calculations were made for a hydraulic model of the lower Vistula which takes into account potential development of barrages in a cascade system. Results obtained from the model simulations and from hydrological calculations were used to estimate the power of hydropower plants and the average annual energy...
-
Electrical properties of A-site Ca-doped LaNb1-xAsxO4-δ ceramics
PublicationThe electrical properties of A-site Ca-doped LaNbO4 with the addition of As in the B-site, have been investigated. Total, grain- and specific grain boundary electric conductivities in different oxygen partial pressure, and water vapour partial pressure were determined. Additional conductivity measurements were performed in nitrogen, to suppress the possible p-type conductivity, focusing on protonic conductivity. The maximum measured...
-
Effects of thermal history on the performance of low-temperature solid oxide fuel cells with Sm0.2Ce0.8O2-δ electrolyte and LiNi0.81Co0.15Al0.04O2 electrodes
PublicationIn this study, low-temperature solid oxide fuel cells with an ∼560 μm thick Sm0.2Ce0.8O2−δ (SDC) electrolyte and ∼890 μm thick LiNi0.81Co0.15Al0.04O2−δ (NCAL) electrodes are constructed and characterized under three experimental conditions. The cell with an NCAL cathode pre-reduced under an H2 atmosphere at 550 °C presents the best electrochemical performance. This is ascribed to facts that the reduction reaction generating Ni–Co...
-
Optical emission spectroscopy of plasma generated by a waveguide-supplied microwave plasma source operated at 915MHz
PublicationIn this paper we present the results of an optical emission spectroscopic study of an atmospheric pressure microwave (915 MHz) nitrogen and nitrogen with carbon dioxide (1%) plasma at high working gas flow rate. This study was aimed at determining rotational Trot and vibrational Tvib temperatures of N+2 ions and N2, CN molecules. The plasma was generated in a waveguide-supplied cavity-resonant type microwave plasma source. All...
-
Nitrogen oxides removal from hydrogen flue gas using corona discharge in marine boilers: Application perspective
PublicationThis paper focuses on the combustion of hydrogen in boilers, as it appears to be a more effective method than using fuel cells for heating purposes due to higher boiler efficiency. One of the main disadvantages of hydrogen combustion in air is NOx formation. Therefore, the authors decided to introduce corona discharge as an inno- vative technique to clean hydrogen flue gas by effectively reducing NOx levels. The method involves...
-
Fast-response optoelectronic detection of explosives’ residues from the nitroaromatic compounds detonation: field studies approach
PublicationWe are presenting an application of optoelectronic nitrogen dioxide (NO2) analyzer based on cavity enhanced absorption spectroscopy in the detection of traces of explosives after detonation. It has been shown that the analyzer using blue-violet laser is able to detect explosive residues after the detonation of various amounts of nitroaromatic compounds (75g-1kg) with higher efficiency than the HPLC soil sample testing equipment,...
-
Solvation of ionic liquids based on N -methyl- N -alkylmorpholinium cations in N,N -dimethylformamide and N,N -dimethylacetamide – Volumetric and compressibility studies
PublicationDensity and sound velocity of the solutions of ionic liquids based on N-alkyl-N-methyl- morpholinium cations: N-ethyl- -methylmorpholinium bis(trifluoromethanesulfonyl)imide, N-butyl-Nmethylmorpholinium bis(trifluoromethanesulfonyl)imide, N-octyl-N-methyl -morpholinium bis(trifluor omethanesulfonyl)imide and N-decyl-N-methylmorpholinium bis(trifluoromethanesulfonyl)imide in N, N-dimethylformamide and N,N-dimethylacetamide were...
-
Evaluating experimental molecular physics studies of radiation damage in DNA*
PublicationThe field of Atomic and Molecular Physics (AMP) is a mature field exploring the spectroscopy, excitation, ionisation of atoms and molecules in all three phases. Understanding of the spectroscopy and collisional dynamics of AMP has been fundamental to the development and application of quantum mechanics and is applied across a broad range of disparate disciplines including atmospheric sciences, astrochemistry, combustion and environmental...
-
Horizontal velocity field derived from EPN and ASG-EUPOS satellite data on the example of south-western part of Poland
PublicationPresently the determination of the velocity field in the global reference frame is possible by using different space techniques and dense terrestrial networks from global to local and regional scales. However, the reliability of such determinations is strongly limited by the restricted number of unmodeled effects. Some of them are periodic (atmospheric or hydrological effects), some instantaneous (natural or man-made seismicity)...
-
Chapter 8 – Active Sampling of Air
PublicationThis chapter reviews the literature information on analytical techniques and laboratory equipment used for active sampling of air (atmospheric and indoor) in regular monitoring research. It describes popular analytical devices applied for sample collection using various types of polymeric bags, e.g. Tedlar bags, Teflon or Nafion bags, and/or stainless steel vacuum containers. It reviews literature data about the application of...
-
Zaufanie w zespole projektowym a (kobiecy) model przywództwa
PublicationArtykuł prezentuje wyniki badań dotyczące znaczenia czynników kształtujących zaufanie w pracy zespołowej, do których należą: adekwatne nagradzanie, dzielenie się informacjami, ustalone cele i zasady pracy, przejrzystość środowiska i otwarta komunikacja. Wyniki koncentrują się na zachowaniach lidera/ przywódcy, które maja wpływ na kształtowanie zaufanie w zespole i pokazują różnice w zależności od płci.
-
Comparative modeling of shear localization in granular bodies with FEM and DEM
PublicationThe intention of the paper is to compare the calculations of shear zones in granular bodies using two different approaches: a continuum and a discrete one. In the first case, the FEM based on a micro-polar hypoplastic constitutive law was used. In the second case, the DEM was taken advantage of, where contact moments were taken into account to model grain roughness. The comparative calculations were performed for a passive case...
-
Microstrip four-port circulator using a ferrite coupled line section
PublicationThis paper describes an alternative configuration of a four-port circulator realized in a microstrip ferrite coupled line technology. The proposed fully planar device employs two three-port circulators consisting of a ferrite coupled line junction and T junction. Both circulators are connected through the same arm, hence, the problem of anti-parallel magnetization met in this type of circulators is avoided without the increase...
-
Low-energy positron scattering from DNA nucleobases: the effects from permanent dipoles
PublicationAb initio quantum calculations for low-energy positron scattering from gas-phase isolated molecular nucleobases which are part of the DNA structure are presented and discussed over the range of 1 eV to 25 eV. The calculations report the integral cross sections (ICSs) and the momentum-transfer cross sections (MTCSs) for Adenine, Guanine, Thymine and Cytosine. The calculations show very clearly the important role of the dominant...
-
HYDROGEN PRODUCTION PERFORMANCE IN THERMOCATALYTIC REACTOR BASED ON THE INTERMETALLIC PHASE OF NI3AL
PublicationThe main aim of the following paper is mathematical modelling for momentum, heat and mass transfer, which is accompanied by chemical surface reactions of the flow of the mixture helium and methanol. The thermocatalytic devices used for decomposition of hydrocarbons incorporate vertical microchannels coupling at the ends and heated to 500 oC at the walls. The results of the experiment were compared with CFD calculations to calibrate...
-
Buckling of simplified models of silo with corrugated walls and vertical stiffeners
PublicationThe paper deals with buckling of cylindrical silos composed of corrugated sheets and vertical stiffeners (columns). Comprehensive finite element analyses were carried out for a perfect silo by means of a linear buckling approach. Corrugated walls were simulated as an equivalent orthotropic shell and vertical thin-walled columns as beam elements. Calculations for perfect silos with different numbers of columns made it possible to...
-
Assesment of (Mn,Co)3O4powders for possible coating material for SOFC/SOEC interconnects
PublicationIn this work (Mn,Co)3O4 spinel powders with different Mn:Co ratio (1:1 and 1:2) and from different commercial suppliers are evaluated for possible powder for production of interconnect coatings. Sinterability of the powders is evaluated on pressed pellets sintered in oxidizing and in reducing/oxidizing atmospheres. For selected powder, coatings are then prepared by the electrophoretic deposition method on Crofer 22 APU stainless...
-
Rational Use of Primary Energy in Single-Family Residential Houses
PublicationThis work presents results of the primary energy use for heating residential single-family house. Analysis includes domestic hot water system (DHW) and heating, ventilation and air condition system (HVAC). During researches the conventional and alternative energy sources (natural gas, biomass, fuel oil, bituminous coal, lignite or electric energy obtained from electric power system – EPS) were used in DHW and HVAC systems. Furthermore...
-
The elasto-plastic numerical study of crack initiation in notched PMMA specimens under uniaxial loading conditions – Tension and torsion
PublicationThis paper presents the results of FEM numerical calculations aimed at describing the plastic strain and stress fields under critical loading conditions: tensile force or torsional moment. The calculations were carried out with reference to the results of experimental tensile and torsional tests of flat PMMA specimens weakened with V-notches of different root radii: 0.5, 2 and 10 mm. The procedure for conducting nonlinear numerical...
-
Mathematical modeling of hydrogen production performance in thermocatalytic reactor based on the intermetallic phase of Ni3Al
PublicationThe main goal of the following work is to adjust mathematical modelling for mass transfer, to specific conditions resulting from presence of chemical surface reactions in the flow of the mixture consisting of helium and methanol. The thermocatalytic devices used for decomposition of organic compounds incorporate microchannels coupled at the ends and heated to 500 oC at the walls regions. The results of the experiment were compared...
-
APPLICATION OF SATELLITE IMAGERY AND GIS TOOLS FOR LAND SURFACE TEMPERATURE ESTIMATION AND VERIFICATION
PublicationLand surface temperature (LST) plays an important role in many land-surface processes on regional as well on global scales. It is also a good indicator of energy flux phenomena and is used as a parameter in various Earth observation related studies. However, LST estimation based on processing and utilisation of satellite derived data constitutes several problems in terms of time limitations, accessibility, atmospheric influence...
-
Low current transformer utilizing Co-based amorphous alloys
PublicationMetal oxide surge arresters have been widely used for protection of power system networks against overvoltages due to atmospheric discharges or malfunction of devices connected to the network. During its operation a surge arrester structure is degradated, what can be observed as an increase of a surge arrester leakage current. Paper presents an implementation of a new, high-permeability, Co64Fe4Ni1Si15B14 amorphous alloy as a current...
-
Low Current Transformer Utilizing Co-Based Amorphous Alloys
PublicationMetal oxide surge arresters have been widely used for protection of power system networks against overvoltages due to atmospheric discharges or malfunction of devices connected to the network. During its operation a surge arrester structure is degradated, what can be observed as an increase of a surge arrester leakage current. Paper presents an implementation of a new, high-permeability, Co64Fe4Ni1Si15B14 amorphous alloy as a current...
-
Structural properties of mixed conductor Ba1−xGd1−yLax+yCo2O6−δ
PublicationBa1−xGd1−yLax+yCo2O6−δ (BGLC) compositions with large compositional ranges of Ba, Gd, and La have been characterised with respect to phase compositions, structure, and thermal and chemical expansion. The results show a system with large compositional flexibility, enabling tuning of functional properties and thermal and chemical expansion. We show anisotropic chemical expansion and detailed refinements of emerging phases as La is...
-
Miniaturized Passive Emission Chambers for In Situ Measurement of Emissions of Volatile Organic Compounds
PublicationThe results of many different studies have demonstrated unequivocally that the quality of indoor air is often much worse than that of atmospheric air. The presence of dangerous chemical compounds in indoor air can have an adverse impact on human health and cause numerous diseases of the respiratory and circulatory systems. Such harmful chemicals get into indoor air as a result of their emission from building and indoor materials....
-
Structural changes of water caused by non-electrolytes: Volumetric and compressibility approach for urea-like analogues
PublicationHydration of thiourea (TU), hydroxyurea (HU, hydroxycarbamide), acetone (AC, 2-propanone) and dimethyl sulfoxide (DMSO) has been investigated with the help of the volumetric and compression measurement. The apparent molar volumes and the apparent molar isentropic (adiabatic) compression have been calculated from the density and speed of sound data at temperatures ranging from 288.15 to 308.15 K at atmospheric pressure (0.1 MPa)....
-
The application of environmental issues in designing urban structures – a framework for comprehensive local planning policies
PublicationThe implementation of environmental issues in planning and designing urban structures is becoming a novel approach and a common practice consistent with the paradigm of sustainable development. Maintaining environmental quality in urban areas, managing natural resources and understanding the complexity of urban systems is becoming increasingly challenging. Therefore, it is important to develop strategies for the integration of...
-
Simulations of air and water flow in a model dike during overflow experiments
PublicationFlow in flood dikes, earth dams, and embankments occurs in variably saturated conditions, with pores of the earth material filled partly with water and partly with air. In routine engineering analysis, the influence of pore air is neglected and the air pressure is assumed equal to atmospheric. In some circumstances, for example, during overtopping of the dike by water, the effect of pore air on water flow and stability of the structure...
-
Reliability assessment of truss towers using Monte Carlo Method, PEM and RSM
PublicationThe paper discusses the reliability assessment of simple random truss structures using three different probabilistic methodologies: the Monte Carlo method, the Point Estimate Method and the Response Surface Method. A benchmark truss structure example is analyzed. A set of numerical calculations of critical load is performed and the results are taken as the basis of advanced probabilistic calculations. Using the samples, numerical...
-
Load carrying capacity of the eccentric joint in the truss made of open cross-sections
PublicationThe influence of eccentricity at intersections of truss members on the load carrying capacity of the truss joint is presented in the paper. The research truss elements were designed as cold-formed open cross section. Analytical calculations, numerical analysis and experimental research were conducted to reveal how the eccentricity affects the effort of material in the joint area. The results of analysis and investigations are compared...
-
The ONETEP linear-scaling density functional theory program
PublicationWe present an overview of the ONETEP program for linear-scaling density functional theory (DFT) calculations with large basis set (planewave) accuracy on parallel computers. The DFT energy is computed from the density matrix, which is constructed from spatially localized orbitals we call Non-orthogonal Generalized Wannier Functions (NGWFs), expressed in terms of periodic sinc (psinc) functions. During the calculation, both the...
-
Verification of the new viscoelastic method of thermal stress calculation in asphalt layers of pavements
PublicationThe new viscoelastic method of thermal stress calculations in asphalt layers has been developed and published recently by the author. This paper presents verification of this method. The verification is based on the comparison of the results of calculations with results of testing of thermal stresses in Thermal Stress Restrained Specimen Test. The calculations of thermal stresses according to the new method were based on rheological...
-
Fluctuation enhanced gas sensing with WO3-based nanoparticle gas sensors modulated by UV light at selected wavelengths
PublicationThe sensitivity and selectivity of WO3-based gas sensors can be enhanced by UV-irradiation-induced modulation, especially if different wavelengths are employed. We used fluctuation-enhanced gas sensing, based on measurements of resistance fluctuations in the gas sensor, to study the effects of such modulation on the noise intensity for ambient atmospheres of synthetic air without and with additions of small amounts of ethanol,...
-
Comparison between measured and calculated underwater pressure of merchant ship
PublicationFrom 2012 The Polish Naval Academy take part in an international research project SIRAMIS, carried out in the framework of the European Defence Agency. The objective of this project is to improve the understanding of ship signature interaction with multi influence sensors in relevant and realistic scenario's. This paper describes selected results of the comparison results of sea trials and model calculations of the hydrodynamic...
-
Wavelet Transform Analysis of Temperature Modulated Gas Sensor Response
PublicationThe aim of the study was to evaluate whether it is possible to extract the information about the gas concentration despite the influence of humidity. Commercial semiconductor sensor response was examined under the application of a periodic temperature change. The data was collected using measurement protocol for different concentrations of ammonia at specified levels of relative humidity. In this work we focused on the evaluation...
-
Logistical Aspects of Energy Conversion Efficiency in Marine Steam Power Plants in Off-Design Conditions
PublicationThe paper presents logistical aspects of energy conversion efficiency in off-design conditions. The main part of the article is based on results of thermodynamic calculation for large propulsion steam turbine under partial loads. Calculations are made on extended mathematical model of two proposed steam turbine thermodynamic cycles using Stodola’s cone law. The conclusion based on calculation re-sults contains importance of off-design...
-
Reliability assessment of truss towers using Monte Carlo Method, PEM and RSM
PublicationThe paper discusses reliability assessment of simple random truss structures using three different probabilistic methodologies: the Monte Carlo Method (MCM), the Point Estimate Method (PEM) and the Response Surface Method (RSM). A benchmark truss structure and a simplified full–size engineering tower are both analyzed. A set of ultimate load numerical calculations is performed and the results are taken as the basis of advanced...
-
Two-step synthesis of niobium doped Na–Ca–(Mg)–P–Si–O glasses
PublicationNiobium doped biosolubility glasses in the Na–Ca–(Mg)–P–Si–O system were prepared by using an untypical two-step synthesis route. The parent glass was melted in air atmosphere at 1350 °C followed by re-melting the glass in Nb crucible with the addition of metallic Mg/Ca powder in the nitrogen atmosphere. The second melting step was carried out at 1450–1650 °C, using an induction furnace. The topography and structure of the obtained...
-
Novel binary mixtures of alkanolamine based deep eutectic solvents with water - thermodynamic calculation and correlation of crucial physicochemical properties
PublicationThis paper demonstrates the assessment of physicochemical and thermodynamic properties of aqueous solutions of novel deep eutectic solvent (DES) built of tetrabutylammonium chloride and 3-amino-1-propanol or tetrabutylammonium bromide and 3-amino-1-propanol or 2-(methylamino)ethanol or 2-(butylamino)ethanol. Densities, speeds of sound, refractive indices, and viscosities for both pure and aqueous mixtures of DES were investigated...
-
Comparison of PCBs and PAHs levels in European coastal waters using mussels from the Mytilus edulis complex as biomonitors
PublicationMussels from the Mytilus edulis complex were used as biomonitors for two groups of organic pollutants: polychlorinated biphenyls (PCBs, congeners: 28, 52, 101, 118, 138, 153 and 180) and polycyclic aromatic hydrocarbons (PAHs, naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benz(a)anthracene, chrysene, benzo(b)fluoranthene, benzo(k)fluoranthene, benzo(a)pyrene, indeno(1,2,3-cd)pyrene,...
-
Miniaturized passive emission test chamber for in-situ measurement of emissions of organic compounds
PublicationThe results of many different studies have demonstrated unequivocally that the quality of indoor air is often much worse than that of atmospheric air (outdoor). One of the main groups of chemical compounds present in indoor air, with proven harmfulness to health,are volatile organic compounds (VOCs). VOCs present indoor comprise a wide variety of hydrocarbons and hydrocarbons derivatives including aliphatic, aromatics, alkylbenzens,...
-
Novel Binary Mixtures of Alkanolamine Based Deep Eutectic Solvents with Water—Thermodynamic Calculation and Correlation of Crucial Physicochemical Properties
PublicationThis paper demonstrates the assessment of physicochemical and thermodynamic properties of aqueous solutions of novel deep eutectic solvent (DES) built of tetrabutylammonium chloride and 3-amino-1-propanol or tetrabutylammonium bromide and 3-amino-1-propanol or 2-(methylamino)ethanol or 2-(butylamino)ethanol. Densities, speeds of sound, refractive indices, and viscosities for both pure and aqueous mixtures of DES were investigated...
-
Ab-initio study of electrical and optical properties of allylamine
PublicationThe Density functional theory is one of most promising methodology in fast and accurate calculations of electrical and optical properties from the atomic basis. In this paper, we calculate electrical and optical properties of allylamine (2-propen 1- amine) in terms of accuracy and speed of calculations obtained by selection of DFT-1/2 method with ultrasoft Vanderbilt pseudopotentials. Comparison of density of states between...
-
Hydrodynamic Pressure Field of a Ship on Shallow Water
PublicationResults of calculations of the hydrodynamic pressure field around the ship were obtained by application of the boundary element method. Hydrodynamic field was calculated for a Polish Navy’s tugboat and transport ship using a program called SHiPP and compared with measurements of the field taken on river near Swinoujscie for two identical tugs H-4 and H-10. Next, a series of HPF calculations was carried out on planes situated at...
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublicationThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
Ab-initio study of electrical and optical properties of allylamine
PublicationThe Density functional theory is one of most promising methodology in fast and accurate calculations of electrical and optical properties from the atomic basis. In this paper, we calculate electrical and optical properties of allylamine (2-propen 1- amine) in terms of accuracy and speed of calculations obtained by selection of DFT-1/2 method with ultrasoft Vanderbilt pseudopotentials. Comparison of density of states between molecule...
-
Comparison analysis of selected nuclear power plants supplied with helium from high-temperature gas-cooled reactor
PublicationThe article presents results of efficiency calculations for two 560 MW nuclear cycles with high-temperature gas-cooled reactor (HTGR). An assumption was made that systems of this type can be used in so-called marine nuclear power plants. The first analysed system is the nuclear steam power plant. For the steam cycle, the efficiency calculations were performed with the code DIAGAR, which is dedicated for analysing this type of systems....
-
Influence of Sb-substitution on ionic transport in lanthanum orthoniobates
PublicationThe results of ionic transport measurements for the lanthanum orthoniobate substituted with 10 and 30 mol% of antimony (LaNb0.9Sb0.1O4 and LaNb0.7Sb0.3O4) are presented and discussed. The influence of calcium co-doping on these properties has also been analysed. It has been shown that for the investigated material protonic conductivity predominates at temperatures up to 800 °C in oxidizing atmospheres under wet conditions. The...