Filters
total: 2417
filtered: 1454
displaying 1000 best results Help
Search results for: STEEL PILES
-
Fracture Surface Topography Parameters for S235JR Steel Adhesive Joints After Fatigue Shear Testing
PublicationThis paper presents the experimental results of a study investigating the effect of holes and notches made on the overlap ends on the strength of adhesive joints. Single-lap joints made of S235JR steel sheets bonded with Araldite 2024-2 epoxy adhesive were tested. For comparative reasons, static shear strength tests and high-cycle fatigue strength tests were performed. Adhesive-filled joints having three holes, each with a diameter...
-
High-temperature kinetics study of 430L steel powder oxidized in air at 600–850 °C
PublicationThe 430L stainless steel powder with a mean particle size of 95 μm was studied to determine its high-temperature oxidation properties. Continuous thermogravimetric measurements were carried out for 100 h in air at temperatures in the range of 600–850 °C. Even though a considerable amount of Cr (up to ˜5 wt.% Cr) inside the grains was depleted – especially inside small grains – no breakaway oxidation was observed. This indicates...
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublicationThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
Evaluation of time and space distribution of magnetic flux density in a steel plate magnetized by a C-core
PublicationBadano wpływ częstości magnesowania płyty stalowej na rozkład przestrzenny indukcji magnetycznej wewnątrz tej płyty. Rozkład ten oceniano na podstawie pomiaru natężenia emisji magnetoakustycznej a także rozkładu na powierzchni płyty natężenia efektu Barkhausena. Wyniki dyskutowane są ilościowo i porównane z wynikami modelowania metodą elementów skończonych, w której uwzględniono efekt powstawania prądów wirowych.
-
Cavitation erosion behavior of 18/8 stainless steel after its laser alloying of manganese
PublicationW pracy przedstawiono wyniki badań własności kawitacyjnych stali nierdzewnej gatunku 18/8 po jej laserowym stopowaniu różną zawartością manganu. Stwierdzono, że przy zawartości Mn w ilości 7,13% występuje największy wzrost twardości po stopowaniu a głębokość umacniania na skutek działania obciążeń kawitacyjnych jest najmniejsza.
-
Environmental degradation of the Cr-Mo steels in liquid hydrocarbons
PublicationPrzedstawiono podatność stali stopwych 26H2MF i 34HNM do naprężeniowego pękania korozyjnego. Środowiskiem do badań było paliwo ciężkie i zużyty olej mineralny.
-
Hydrogen degradation of structural steels in technical hydrocarbon liquids
PublicationDla stali stopowych przeprowadzono badania absorpcji wodoru, mechaniczno-korozyjne przy stałej małej prędkości odkształcania, przy stałym obciążeniu i przy obciążeniu cyklicznie-zmiennym. Środowiskiem było paliwo kotłowe, przepracowany olej mineralny oraz gliceryna. Stwierdzono, iż pochłonięty wodór nie powoduje przedwczesnego zniszczenia stali poddanych działaniu stałego obciążenia ponizej granicy plastyczności oraz, że zaabsorbowany...
-
Corrosion behavior of vacuum sintered duplex stainless steels
Publication -
The corrosion resistance of laser surface alloyed stainless steels
Publication -
Weldability of high strength steels in wet welding conditions
PublicationIn this paper are characterized problems of high strength steel weldability in underwater wet welding conditions. Water as a welding environment intensifies action of unfavourable factors which influence susceptibility to cold cracking of welded steel joints. The susceptibility to cold cracking of S355J2G3 steel and S500M steel in wet conditions was experimentally estimated (by using Tekken test). It was concluded that the steels...
-
Hydrogen degradation of high strength low alloyed steels.
PublicationBadano wpływ polaryzacji katodowej na własności stali węglowej, stali o podwyższonej i wysokiej wytrzymałości metodą stałego powolnego odkształcania.Stwierdzono, że stopień kruchości wodorowej każdej z badanych stali zależał od stężenia wodoru dyfuzyjnego.
-
Investigations of welded joints of dissimilar heat resistant steels.
PublicationPrzeprowadzono badania metalograficzne połączeń spawanych różnorodnych stali żarowytrzymałych rur o przekroju 31,8x7,1 mm ze stali 10H2M z blachą ze stali 20H23N18. Badania makro- i mikrostruktury złączy spawanych wykazały, że istotnym czynnikiem wpływającym na właściwości mechaniczne złącza jest obecność wad takich jak pory lub wtrącenia żużla. Te nieciągłości w materiale powodują koncentrację naprężeń i powstawanie mikropęknięć.
-
The Application of Cluster Analysis in the Assessment of the Weldability of Unalloyed Steels
PublicationNon-alloy steels constitute a large group of steels characterised by diversified chemical composition, structural morphology and a wide range of mechanical properties (determining weldability). The paper presents results of multidimensional analyses (based on cluster analysis) of 110 selected unalloyed steel grades. Properties adopted as diagnostic features included the chemical composition, mechanical properties (yield point)...
-
Hydrogen degradation of high-strength weldable steels in seawater
PublicationOceniono podatność na niszczenie wodorowe stali spawalnych o wysokiej wytrzymałości przy obciążeniach monotonicznie rosnących. Badano dwa gatunki stali ulepszonych cieplnie i ich złącza spawane. Przeprowadzono próby rozciągania z małą prędkością odkształcania w wodzie morskiej przy polaryzacji katodowej. Wykonano próby przenikania wodoru metodą Devanathana-Stachurskiego.
-
Hydrogen delayed cracking of high-strength weldable steels
PublicationOceniano podatność na niszczenie wodorowe stali 14HNMBCu o wysokiej wytrzymałości i jej połączeń spawanych przy obciążeniu stałym w wodzie morskiej. Badania przeprowadzono w powietrzu, oraz w środowisku wody morskiej przy potencjale korozyjnym i przy polaryzacji katodowej. Obecność lub brak opóźnionych pęknięć próbek z karbem przyjęto za miarę odporności na niszczenie wodorowe przy stałym obciążeniu.
-
Influence of process of straightening ship hull structure made of 316L stainless steel on corrosion resistance and mechanical properties
PublicationThe AISI 316L type steel belongs to the group of chromium-nickel stainless steels. They are determined according to European standards as X2CrNiMo17-12-2 and belong to the group of austenitic stainless steels. Steels of this group are used for elements working in seawater environments, for installations in the chemical, paper, and food, industries, for architectural elements, and many others. The chemical composition of corrosion-resistant...
-
Vplyv modifikácie dubovégo dreva technólogiou thermo-wood na zrnistosŤ piliny z procesov pilenia dreva na rámovej pile PRW 15M
PublicationW referacie przedstawiono wpływ modyfikacji termicznej drewna dębowego technologią ThermoWood na ziarnistość wiórów z procesu przecinania na pilarce ramowej PRW15M. Stwierdzono, że trociny uzyskane z drewna dębowego modyfikowanego termicznie nie zawierają w swoim składzie szkodliwych dla układu oddechowego człowieka cząstek z frakcji PM2.5, a ponadto nie wykryto cząstek frakcji PM10, które mogłyby tworzyć smog w środowisko pracy.
-
Evaluation of cavitation erosion–corrosion degradation of mild steel by means of dynamic impedance spectroscopy in galvanostatic mode
Publication -
Experimental validation of the use of energy transfer ratio (ETR) for damage diagnosis of steel-concrete composite beams
Publication -
Strengthening mechanism and precipitate evolution of a multi-application special engineering steel designed based on a hybrid idea
Publication -
Experiments and Numerical Simulations of the Annealing Temperature Influence on the Residual Stresses Level in S700MC Steel Welded Elements
Publication -
Appliance of High Speed Camera during Industrial Exploitation on the Example of Static and Dynamic Tests of Steel Probes
Publication -
Numerical analysis of influence of intermediate stiffeners setting on the stability behaviour of thin-walled steel tank shell
Publication -
Comparison of properties of magnetoacoustic emission and mechanical Barkhausen effects for P91 steel after plastic flow and creep
PublicationW artykule przedstawiono wyniki pogłębionej analizy sygnału szumowego efektu Barkhausena dla próbek ze stali krzemowej Fe-2%Si po deformacji plastycznej. Badane były próbki po walcowaniu na zimno powodującym odkształcenie względne w zakresie do 8%. Pierwsze podejście polegało na analizie w dziedzinie czasu widma badanego sygnału. Analiza ta została uzupełniona o analizę liczby zliczeń impulsów w funkcji napięcia progowego, zarówno...
-
Niszczenie wodorowe złączy spawanych ze stali S355 = Hydrogen degradation of welded joints of S355 steel
PublicationW artykule przedstawiono ocenę podatności na niszczenie wodorowe złączy spawanych ze stali S355. Jako parametry niszczenia wodorowego wybrano względne wartości energii zniszczenia, wydłużenia, przewężenia i wytrzymałości na rozciąganie. Parametry te wyznaczono w próbie odkształcania z małą prędkością na próbkach okrągłych, gładkich. Stwierdzono, że stal S355w środowisku kwaśnym podczas polaryzacji katodowej, jest bardziej skłonna...
-
Complex Corrosion Properties of AISI 316L Steel Prepared by 3D Printing Technology for Possible Implant Applications
Publication -
Surface Layer Properties of Sintered Ferritic Stainless Steel Remelted and Alloyed with FeNi and Ni by HPDL Laser
Publication -
Laser Thermal Oxidation by Ytterbium-Doped Fibre Laser of the Hot and Cold-Rolled Stainless Steel Surface
Publication -
Wear of carbide inserts during turning of C45 steel in dry cutting conditions and in presence of emulsion mist
Publication -
Formation of Surface Topography During Turning of AISI 1045 Steel Considering the Type of Cutting Edge Coating
Publication -
Influence of PWHT Parameters on the Mechanical Properties and Microstructural Behavior of Multi-Pass GTAW Joints of P92 Steel
PublicationThe 9% Cr steels were developed for ultra-supercritical (USC) power plants to meet the requirements of high operating temperature and pressure. These steels are produced to operate at high temperatures where impact toughness is not a concern; however, it becomes important for the welded joints to have good impact toughness at room temperature for manufacturing. The present work investigates the effect of the post-weld heat treatment...
-
Fatigue fracture surface metrology of thin-walled tubular austenitic steel specimens after asynchronous loadings
PublicationThis paper aims to study the effect of asynchronous axial-torsional strain-controlled loading histories on fracture surface behavior of thin-walled tubular X5CrNi18-10 (304/304L) austenitic steel specimens. Tests under pure axial loading and pure torsional loading are also conducted to better segregate the effect of multiaxiality. The fractures surface topographies were examined through the profiles over the entire surface with...
-
Numerical evaluation of dynamic response of an experimentally tested base-isolated and fixed-base steel structure model
PublicationSeismic isolation is recognized as one of the most popular and effective methods of protecting structures during earthquake. The present paper is focused on the comparison be-tween the dynamic responses of buildings with fixed and isolated bases exposed to seismic exci-tations. The aim of the study is to investigate the effectiveness of a simplified base isolation numerical modelling technique using the linear springs. One-storey...
-
Non-Destructive Diagnostics of Concrete Beams Strengthened with Steel Plates Using Modal Analysis and Wavelet Transform
PublicationExternally bonded reinforcements are commonly and widely used in civil engineering objects made of concrete to increase the structure load capacity or to minimize the negative effects of long-term operation and possible defects. The quality of adhesive bonding between a strengthened structure and steel or composite elements is essential for effective reinforcement; therefore, there is a need for non-destructive diagnostics of adhesive...
-
Instantaneous Impedance Analysis of Non-Stationary Corrosion Process: a Case Study of Carbon Steel in 1M HCl
PublicationThe paper concerns the problem of evaluation of stationarity of carbon steel corrosion in 1M HCl. Comparison of corrosion rate with addition of corrosion inhibitor to the reference measurement is the most often used way of evaluating inhibitor efficiency. Such an approach is valid only if corrosion rate is a stationary process. Two complementary techniques were used simultaneously: volumetric analysis of evolved hydrogen and instantaneous...
-
Non-Destructive Testing of the Longest Span Soil-Steel Bridge in Europe—Field Measurements and FEM Calculations
PublicationThe article describes interdisciplinary and comprehensive non-destructive diagnostic tests of final bridge inspection and acceptance proposed for a soil-steel bridge made of corrugated sheets, being the European span length record holder (25.74 m). As an effect of an original concept a detailed and precise information about the structure short-term response was collected. Periodic diagnostics of bridge deformations was done one...
-
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublicationThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Qualification of brazing procedure for furnace brazing of austenitic steel according to requirements of the ASME BPVC section IX
PublicationThe article presents the procedure for qualifying brazing technology in a vacuum furnace on the example of stainless steel elements joined with copper filler material from the F-No group. 105, in accordance with the ASME Sec. IX, part QB (ASME Boiler and Pressure Vessel Code. Qualification Standard for Welding, Brazing and Fusing; Procedures; Welders; Brazers; and Welding, Brazing and Fusing Operators). The essential variables...
-
Evaluation of the resistance of steel–concrete adhesive connection in reinforced concrete beams using guided wave propagation
PublicationThe development of the nondestructive diagnostic methods is of significant importance in the last decades. A special attention is paid to diagnostics of reinforced concrete structures, which are very popular in the civil engineering field. A possible use of the guided waves in the estimation of the resistance of steel–concrete adhesive connection is studied in the following paper. The relationships relating adhesive connection...
-
Influence of metallic porous microlayer on pressure drop and heat transfer of stainless steel plate heat exchanger
PublicationThe experimental analysis of passive heat transfer intensification in the case of plate heat exchanger has been carried out. The metallic porous layer was created on the heat transfer surface of analyzed unit. The experiment was accomplished in two stages. In the first stage the commercial stainless steel gasketed plate heat exchanger was investigated, while in the second one – the identical heat exchanger but with the modified...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Evaluation of cavitation erosion-corrosion degradation of mild steel by means of Dynamic Impedance Spectroscopy in galvanostatic mode
PublicationPrzedstawiono wyniki badań degradacji stali węglowych na skutek oddziaływania erozji-korozji kawitacyjnej. Do analizy wykorzystano technikę Dynamicznej Elektrochemicznej Spektroskopii Impedancyjnej w trybie galwanostatycznym, bliżej odwzrorowującym warunki naturalne. Do oceny stopnia degradacji posłużyły również funkcja ubytku masy MDPR oraz obrazy mikroskopowe SEM. Potwierdzono wpływ łączonej degradacji erozyjno-korozyjnej na...
-
The Influence of Gas Mixture in the Glow-Discharge Nitriding Process of Austenitic Stainless Steel on Characteristic of Nitrided Cases
PublicationAustenitic stainless steels characterize with excellent corrosion resistance, although low mechanical properties. In many cases that limits their exploitation in industrial applications. Moreover, austenitic stainless steel is susceptible to local corrosion in the presence of halide ions. In present works, it was emphasized that the nitriding of austenitic stainless steels gives some potential abilities to obtain beneficial effect...
-
Load-carrying capacity of axially loaded concrete-filled steel tubular columns made of thin tubes
PublicationAn experimental investigation was conducted on 30 CFST columns. An influence of the following factors on load-carrying capacity of the investigated columns was analyzed: the column slenderness (l1 = 42, l2 = 27 and l3 = 15), the tube thickness (the reinforcement ratio was equal to 4% or 6%), the way of applying the load to CFST columns (through the concrete core or through the entire cross-section), the bond strength between a...
-
Analysis of load carrying capacity and destruction mechanism of an intermediate anchorage steel plate for pillar jib crane
PublicationPillar jib cranes are often mounted to existing floors with the use of an intermediate anchorage steel plate instead of using independent foundations, what is shown in the figure. Standards for steel design provide only basic rules for the design of such an intermediate plate. This study presents a simple design approach by using a numerical model in order to analyze different parameters that have significant influence in the anchorage...
-
The effect of long-term service at elevated temperatures on structure and mechanical properties of Cr-Mo-V steel
PublicationPurpose: of this paper is to reveal the microstructural changes in 13HMF steel exposed to long-term service at elevated temperatures. The degradation of bainite structure was determined and carbides morphology has been examined. The influence of carbides evolution was discussed in dependence of creep rupture strength and mechanical properties of the steel.
-
Finite element method simulations of various cases of crash tests with N2/W4/A steel road barrier
PublicationThe subject of this study is performance of N2/W4/A steel road safety barrier investigated in numerical simulations. System was checked under several types of initial conditions, which were assumed basing on the TB11 and TB32 normative crash tests. The main goal of present study is to investigate the relationship between initial conditions (angle and velocity) of the impact and the severity indices (associated to the vehicle occupant) during...
-
Influence of nonlinearities on the efficiency and accuracy of FEM calculations on the example of a steel build-up thin-walled column
PublicationDue to the increase of computing capabilities of standard processing units, it is possible to perform complex analyses, considering a number of nonlinearities, such as geometric, material and boundary (contact) even on personal computers. In the paper, the authors have analysed the efficiency and accuracy of standard PC’s FEM calculations performed in Abaqus CAE 2017 software on the example of a critical load assessment of a thin-walled...
-
Impact of eddy currents on Barkhausen and magnetoacoustic emission intensity in a steel plate magnetized by a C-core electromagnet.
PublicationZbadano (zmierzono i modelowano metodą elementów skończonych) wpływ częstości magnesowania na przestrzenny i czasowy rozkład indukcji magnetycznej wewnątrz płyty stalowej. Wyznaczono i zmierzono natężenie polowego rozkładu Barkhausena (HEB) na powierzchni płyty oraz natężnie emisji magnetoakustycznej (EMA) z całej magnesowanej objętości. Wykazano, iż obserwowane zmiany w natężeniu HEB i EMA są wynikiem zmian w rozkładzie indukcji...
-
Wpływ obróbki cieplnej na strukturę stali krzemowej. The heat treatment influence on the silicon steel morphology
PublicationStal sprężynową 55S2 poddano obróbce cieplnej przy poprawnych i zawyżonych paramatrach temperaturowo-czasowych. Dla materiału o wadliwej strukturze wyjściowej, dobór wyższych temperatur i czasów obróbki pozwolił na otrzymanie bardziej poprawnych struktur i własności materiału.