Filters
total: 1731
filtered: 1235
displaying 1000 best results Help
Search results for: arachnoid cyst
-
Development of nanoscale morphology and role of viscoelastic phase separation on the properties of epoxy/recycled polyurethane blends
PublicationA novel and cost-effective approach towards the modification of epoxy matrix has been developed using recycled polyurethane for the first time without sacrificing any of the intrinsic properties of the resin. Polyurethane, recycled from waste foam by glycolysis process (RPU), was found to be very effective in improving the properties of the thermosetting resin based on Diglycidyl ether of bisphenol-A (DGEBA). The effect of the...
-
Rapid tolerance‐aware design of miniaturized microwave passives by means of confined‐domain surrogates
PublicationThe effects of uncertainties, primarily manufacturing tolerances but also incomplete information about operating conditions or material parameters, can be detrimental to the performance of microwave components. Quantification of such effects is essential to ensure a meaningful evaluation of the structure, in particular, its reliability under imperfect fabrication procedures. The improvement of the circuit robustness can be achieved...
-
Gossiping by energy-constrained mobile agents in tree networks
PublicationEvery node of an edge-weighted tree network contains a data packet. At some nodes are placed mobile agents, each one possessing an amount of energy (not necessarily the same for all agents). While walking along the network, the agents spend the energy proportionally to the distance traveled and collect copies of the data packets present at the visited network nodes. An agent visiting a node deposits there copies of all currently...
-
Fast and reliable knowledge-based design closure of antennas by means of iterative prediction-correction scheme
PublicationA novel framework for expedited antenna optimization with an iterative prediction-correction scheme is proposed. The methodology is comprehensively validated using three real-world antenna structures: narrow-band, dual-band and wideband, optimized under various design scenarios. The keystone of the proposed approach is to reuse designs pre-optimized for various sets of performance specifications and to encode them into metamodels...
-
Effects of preheating on laser beam–welded NSSC 2120 lean duplex steel
PublicationDuplex stainless steels show sustainable alternative for the conventional austenitic grades, with higher strength, higher resistance against stress corrosion cracking, and lower purchase cost. Thus, duplex stainless steel gains more attention in construction, oil and gas, and chemical industries. Among duplex stainless steels, low nickel and low molybdenum alloyed lean duplex stainless steel are a cost-efective substitution of...
-
Globalized Simulation-Driven Miniaturization of Microwave Circuits by Means of Dimensionality-Reduced Constrained Surrogates
PublicationSmall size has become a crucial prerequisite in the design of modern microwave components. Miniaturized devices are essential for a number of application areas, including wireless communications, 5G/6G technology, wearable devices, or the internet of things. Notwithstanding, size reduction generally degrades the electrical performance of microwave systems. Therefore, trade-off solutions have to be sought that represent acceptable...
-
Influence analysis of selected parameters on the ASON/GMPLS control plane performance
PublicationThe paper regards the problem of ASON/GMPLS performance. The authors present influence analysis of selected parameters on the ASON/GMPLS control plane performance represented in mean Connection Set-up Time E(CST) and mean Connection Release Time E(CRT). The selected parameters are: offered traffic, request intensity and proportion of requests class. The influence analysis is performed with simulation method by using OMNeT++ discrete-event...
-
Indykatory mobilne GIS w analizie ruchu miejskiego
PublicationW ramach artykułu autorzy przedstawią możliwości monitorowania sytuacji komunikacyjnej miasta z wykorzystaniem autorskiego i dedykowanego systemu monitorowania ruchu w mieście, opartego o pakiet oprogramowania stacjonarnego i mobilnego przeznaczonego dla korporacji taxi. Celem publikacji jest przedstawienie założeń optymalnych i minimalnych do realizacji monitoringu ruchu w mieście. Przywołane zostaną autorskie próby wdrożeń rozwiązań...
-
Analiza kosztów i czasu budowy domu jednorodzinnego w technologii drewna krzyżowo klejonego CLT
Publication-
-
Hydro Lubricants: Water-based lubricants for hydropower applications
PublicationSeveral different base oil types exist in the market including mineral and synthetic oils (e.g. polyalphaolefins, ester, polyglycol, etc.) and are currently widely in use. Although synthetic oils have drawn great attention over the past few decades in terms of their tribological benefits, mineral oils are still widely used in hydropower applications due primarily to their low cost and easy miscibility with other oils. However,...
-
Remote Estimation of Video-Based Vital Signs in Emotion Invocation Studies
PublicationAbstract— The goal of this study is to examine the influence of various imitated and video invoked emotions on the vital signs (respiratory and pulse rates). We also perform an analysis of the possibility to extract signals from sequences acquired with cost-effective cameras. The preliminary results show that the respiratory rate allows for better separation of some emotions than the pulse rate, yet this relation highly depends...
-
Multicomponent layers for aluminium alloys surface consolidation
PublicationThe main reason of the surface modification of the components such as pistons and cylinder blocks made of cast aluminium alloys is to obtain high hardness, wear and corrosion resistance of the working surface for larger lifetime of the motor-car and aircraft engines. In that aspect, the new conception of development - by hybrid method - of surface layers containing manganese, nitrogen, sulphur (Mn-N-S) and manganese, nitrogen,...
-
Efektywność studiów Master of Business Administration (MBA) w Polsce
PublicationW artykule oszacowano efektywność 28 programów studiów MBA w Polsce za pomocą „alokacyjnego” modelu New Cost (Tone 2002) należącego do nieparametrycznej metody DEA. Za nakłady przyjęto liczbę godzin programu MBA oraz jego koszt, zaś za wynik ogólny wskaźnik rankingowy studiów MBA w 2018 roku opracowany przez Perspektywy. Uzyskane wyniki świadczą o przeciętnej efektywności studiów MBA wynoszącej 68%, tylko sześć programów było...
-
Controling w zarządzaniu bezpieczeństwem pracy
PublicationW artykule przedstawiono możliwość wykorzystania controllingu do badania zagrożeń w procesie pracy. Dla oceny rozwiązań usprawniających wprowadzono pojęcie oszczędności zasobu typu praca i typu materiał, zużywanych w procesie realizacji zadań wytwórczych. Artykuł podkreśla możliwość osiągania efektów ekonomicznych (ograniczenia kosztów) w wyniku poprawy warunków pracy.CONTROLLING IN WORK SAFETY MANAGEMENTThe article presents the...
-
Ocena techniczno-ekonomiczna stosowania pomp ciepła w systemach ogrzewania wolnostojących budynków mieszkalnych
PublicationW artykule przedstawiono ocene techniczno-ekonomiczną ogrzewania wolnostojącego budynku mieszkalnego, realizowanego w oparciu o dwa systemy. Analizę opłacalności przeprowadzono dla układów, których porównanie jest w wysokim stopniu adekwatne do rzeczywistych warunków ekonomicznych i technicznych. Ocenie poddano systemy c.o. i c.w.u. wykorzystujące sprężarkową pompę ciepła lub alternatywnie kocioł olejowy, przy założeniu, że parametry...
-
Optimising Sequencing Batch Reactor Operation Cycle Planning Using Evolutionary Algorithm
PublicationThe objective of this research was to optimise the operation cycle of the Sequencing Batch Reactor (SBR). Appropriate time balances of aerobic to anaerobic phases, as well as a set dissolved oxygen level are the key to ensuring the quality of effluent from the wastewater treatment process. The proposal to solve this optimisation problem was based on multi-objective optimisation using an evolutionary multi-objective optimisation...
-
Adaptive estimation of the transformer stray capacitances for DC–DC converter modelling
PublicationNew low cost and accurate estimation method of transformer stray capacitances for wide band DC–DC converter modelling and design is proposed. The Wiener filter (WF) method is applied to estimate the transformer impedance – referred to the selected transformer winding configurations. Laboratory tests are used to adapt the filter, that is to find optimal impedance which minimises mean square error between measured, noise perturbed...
-
Evaluation of position estimation based on accelerometer data
PublicationThe paper concerns the problem of integrating data from accelerometers. A suitable model of a MEMS accelerometer is presented which is a part of inertial measurement units (IMU). Such units allow to measure orientation as well as to localize systems. They also appear to be applicable for systems positioning. The main purpose of the paper is to discuss conditions that must be satisfied to calculate the location of the sensor by...
-
Euro 2012 in Gdańsk, Poland. Is it worth using public funds?
PublicationThe aim of this study is to estimate the willingness - to - pay (WTP) among the community of the Pomeranian region, Poland in connection with intangible benefits and costs st emming from hosting the Euro 2012 in Gdansk. A survey conducted among 407 respondents was the source of information. The results of the study show that the average value of WTP benefit for the whole sample was 45,72 PLN2012 and WTP cost...
-
A derivatisation agent selection guide
PublicationThe development of new tools for providing high quality information in a cost-effective and expeditious way is one of the main aims of analytical chemistry. Remarkably, the introduc- tion of the 12 principles of green chemistry paved the way forward for the development of analytical methodologies that are, ideally, inherently safe for the operator and the environ- ment, with the least possible consumption of energy and chemicals,...
-
Mechanical, durability, depolluting and electrical properties of multifunctional mortars prepared with commercial or waste carbon-based fillers
PublicationCarbon-based fillers from industrial wastes and commercial ones were compared to improve the properties of lime-based mixes. As commercial fillers, graphene nanoplatelets and activated carbon were used, whereas as industrial wastes a char obtained by the gasification of biomasses and a used foundry sand were chosen. Carbon-based wastes were found to be a good cost-effective alternative to commercial carbon based fillers to increase...
-
Promising Nanoparticle-Based Heat Transfer Fluids—Environmental and Techno-Economic Analysis Compared to Conventional Fluids
PublicationProviding optimal operating conditions is one of the major challenges for effective heating or cooling systems. Moreover, proper adjustment of the heat transfer fluid is also important from the viewpoint of the correct operation, maintenance, and cost efficiency of these systems. Therefore, in this paper, a detailed review of recent work on the subject of conventional and novel heat transfer fluid applications is presented. Particular...
-
Recent Advances in Development of Waste-Based Polymer Materials: A Review
PublicationLimited petroleum sources, suitable law regulations, and higher awareness within society has caused sustainable development of manufacturing and recycling of polymer blends and composites to be gaining increasing attention. This work aims to report recent advances in the manufacturing of environmentally friendly and low-cost polymer materials based on post-production and postconsumer wastes. Sustainable development of three groups...
-
Optimized Stress and Geometry Control of Spherical structures under Lateral Loadings
PublicationIn this paper, a numerical model of a double-layer spherical structure has been examined under lateral loadings. When the structure has been distorted due to loadings, the dislocated joints have been moved to their original positions utilizing the adjustment techniques based on the force method. Meanwhile, the members’ internal forces were kept in the desired domain. Optimization techniques were also implemented in order to minimalize...
-
A new approach to cross-bonding in medium voltage cable lines
PublicationThe medium voltage underground cable sheaths are usually bonded and earthed in every substation on the cable route. This results in additional power losses in the sheaths. The paper presents an idea of reducing power losses caused by sheaths cross-bonding. The idea of sheaths cross-connecting only in selected MV/LV substations is given instead of a typical solution, where sheaths cross-bonding requires installing additional joints...
-
Performance of ASON/GMPLS architecture in condition of wavelength conversion and without wavelength conversion
PublicationThe paper regards the problem of ASON/GMPLS performance in condition of wavelength and without wavelength conversion. The authors present influence analysis in condition of wavelength and non-wavelength conversion on the ASON/GMPLS control plane performance represented by mean Connection Set-up Time E (CST) and request loss probabilities. The offered traffic to the transport layer and request intensity have been changed for evaluation...
-
Novel structure and EM-driven design of miniaturized microstrip rat-race coupler
PublicationIn this paper, a novel structure and design procedure of a miniaturized microstrip rat-race coupler (RRC) is described. Small size of the RRC is achieved by folding the transmission lines of the conventional circuit into its interior, as well as by implementation of the structure on three layers. The final size of the coupler realized for the operating frequency of 1 GHz is only 220 mm2, which gives over 95% footprint reduction...
-
The Impact of Building Performance Analysis on intuition Development and Decision Making Rationality
PublicationContemporary architectural workshop is characterized by the ability to efficiently collect and process huge amounts of geometric and non-geometric information. Virtual substitutes for buildings and structures allow to analyze various aspects of real life activity at various stages of the design process. The possibility of increased prognostic quantitative data acquisition, such as cost of energy consumption, shifts architectural...
-
Natural ventilation performance of family building in cold climate during windy days
PublicationAdequately designed natural ventilation is the cheapest and easiest way to effectively remove indoor pollutants and keep the fresh air inside a building. A prediction of performance and effectiveness of ventilation in order to determine the design of a ventilation system can provide real and long term cost savings. The paper presents results of performance (air change rate ACH) and effectiveness (CO2 concentration in the breathing...
-
Speed Sensorless AC Drive with Inverter LC Filter and Fault Detection Using Load Torque Signal
PublicationThe industrial development in recent years has seen a major increase in the use of induction motors, whereby the cost has to be as low as possible and the lifetime as long as possible. To follow up this desire, investigations in this area have become very intense. For that reason, this paper presents a solution for driving an induction motor and simultaneous fault detection with no need for additional sensors. In order to achieve...
-
Thermoplastic Elastomers Filled With GTR
PublicationIn recent years, searching for new and cost-effective methods of recycling waste tires has been a subject of research in many laboratories worldwide. This is due to regulations in the law and environmental factors, which have both stimulated industry to re-use high quality rubber found in ground tire rubber (GTR). One of the most promising solutions in this area seems to be thermoplastic elastomers (TPEs) filled with GTR, which...
-
k-Penalty: A Novel Approach to Find k-Disjoint Paths with Differentiated Path Costs
PublicationW artykule rozpatrywany jest problem ochrony dedykowanej na wypadek awarii wielokrotnej elementów sieci teleinformatycznej. Wspomniana ochrona jest możliwa do zapewnienia poprzez wyznaczenie i zainstalowanie zbioru k rozłącznych ścieżek dla każdego żądania. W szczególności rozpatrywany jest problem wyznaczenia k rozłącznych ścieżek w sieciach typu ''multi-cost'', w przypadku których koszt dowolnego łącza może być różny dla każdej...
-
Investigation of photothermolysis therapy of human skin diseases using optical phantoms
PublicationDermatological diseases, such as neurofibroma (Recklinghausen disease) or hemangiomas can be efficiently treated using photothermolysis from laser irradiation. We have utilized a developed 975 nm fiber diode laser as a low-cost alternative over common Nd:YAG lasers. This paper describes the investigations of interaction of 975 nm diode laser radiation-pulses with optical skin phantoms which were designed and manufactured in our...
-
Design space reduction and variable-fidelity EM simulations for feasible Pareto optimization of antennas
PublicationA computationally efficient procedure for multi-objective optimization of antenna structures is presented. In our approach, a response surface approximation (RSA) model created from sampled coarse-discretization EM antenna simulations is utilized to yield an initial set of Pareto-optimal designs using a multi-objective evolutionary algorithm. The final Pareto front representation for the high-fidelity model is obtained using surrogate-based...
-
Mobile indicators in GIS and GPS positioning accuracy in cities
PublicationThe publication describes the possible use of tele-geoprocessing as a synergy of modern IT solutions, telecommunications and GIS algorithms. The paper presents a possibility of urban traffic monitoring with the use of mobile GIS indicators of dedicated monitoring system designed for taxi corporation. The system is based on a stationary and mobile software package. The optimal and minimal assumptions for the monitoring of urban...
-
Image Processing Techniques for Distributed Grid Applications
PublicationParallel approaches to 2D and 3D convolution processing of series of images have been presented. A distributed, practically oriented, 2D spatial convolution scheme has been elaborated and extended into the temporal domain. Complexity of the scheme has been determined and analysed with respect to coefficients in convolution kernels. Possibilities of parallelisation of the convolution operations have been analysed and the results...
-
Hierarchical Estimation of Human Upper Body Based on 2D Observation Utilizing Evolutionary Programming and 'Genetic Memory'
PublicationNew method of the human body pose estimation based on single camera 2D observation is presented. It employs 3D model of the human body, and genetic algorithm combined with annealed particle filter for searching the global optimum of model state, best matching the object's 2D observation. Additionally, motion cost metric is employed, considering current pose and history of the body movement, favouring the estimates with the lowest...
-
Evaluation of Vehicle Routing Problem Algorithms for Transport Logistics Using Dedicated GIS System
PublicationThe development and research related to optimization of fleet management is of high interest among many industrial and scientific entities related to logistics and transport. Optimal distribution of transportation resources leads to significant cost reduction. In this context, scientific research related to so called Vehicle Routing Problem (VRP) which relies on determining the shortest transport routes for a strictly limited number...
-
A Measurement-Based Approach for Speed Control of Induction Machines
PublicationThis paper presents an approach to design a measurement-based controller for induction machines. The proposed control approach is motivated by the fact that developing an appropriate mechanical model of such induction machines is a challenging task. Since our proposed control methodology is only on the basis of measured data, the controller design does not require any information about the model of the mechanical part. The control...
-
Size Reduction of Microwave Couplers by EM-Driven Optimization
PublicationThis work addresses simulation-driven design optimization of compact microwave couplers that explicitly aims at circuit footprint area reduction. The penalty function approach allows us to minimize the area of the circuit while ensuring a proper power division between the output ports and providing a sufficient bandwidth with respect to return loss and isolation around the operating frequency. Computational cost of the optimization...
-
Towards the boundary between easy and hard control problems in multicast Clos networks
PublicationIn this article we study 3-stage Clos networks with multicast calls in general and 2-cast calls, in particular. We investigate various sizes of input and output switches and discuss some routing problems involved in blocking states. To express our results in a formal way we introduce a model of hypergraph edge-coloring. A new class of bipartite hypergraphs corresponding to Clos networks is studied. We identify some polynomially...
-
Multi-criteria Differential Evolution for Optimization of Virtual Machine Resources in Smart City Cloud
PublicationIn a smart city, artificial intelligence tools support citizens and urban services. From the user point of view, smart applications should bring computing to the edge of the cloud, closer to citizens with short latency. However, from the cloud designer point of view, the trade-off between cost, energy and time criteria requires the Pareto solutions. Therefore, the proposed multi-criteria differential evolution can optimize virtual...
-
PUBLIC SOURCES OF FINANCE FOR CULTURE AS AN ELEMENT OF CULTURAL SECURITY IN POLAND
PublicationCulture is an important element of the country, playing an important role both for its security and the economy. It cannot be only seen as a cost-creating sector, but may be a significant factor in economic development. For this to happen, it is necessary to create a system of financing this economic sector. This article’s aim is to analyze the use of funds from public sources in Poland to finance culture-related activities. The...
-
Corrosion Study of Ceria Protective Layer Deposited by Spray Pyrolysis on Steel Interconnects
PublicationSingle fuel cells and electrolysis cells are assembled into stacks using interconnects in order to increase power and gas production capacity. The most common choice for the interconnect material is stainless steel. It has good electrical and mechanical properties and is also cost effective. One of the problems when using steel is the formation of a thermally grown oxide scale during use which has a lower electrical conductivity...
-
Real‐Time PPG Signal Conditioning with Long Short‐Term Memory (LSTM) Network for Wearable Devices
PublicationThis paper presents an algorithm for real‐time detection of the heart rate measured on a person’s wrist using a wearable device with a photoplethysmographic (PPG) sensor and accelerometer. The proposed algorithm consists of an appropriately trained LSTM network and the Time‐Domain Heart Rate (TDHR) algorithm for peak detection in the PPG waveform. The Long Short‐Term Memory (LSTM) network uses the signals from the accelerometer...
-
Automatic Correction of Non-Anechoic Antenna Measurements using Low-Pass Filters
PublicationPrototype measurements belong to key steps in the development of antenna structures. They are normally performed in expensive facilities, such as anechoic chambers (ACs). Alternatively, antenna performance can be extracted (at a low cost) in non-anechoic conditions upon appropriate post-processing. Unfortunately, existing correction algorithms are difficult to set up and prone to failure, which limits their practical usefulness....
-
E-Voting System Evaluation Based on the Council of Europe Recommendations: nVotes
PublicationE-voting implantation has been facing important challenges in recent years. Several incidents, together with a lack of evaluation methodologies social and cultural customs hinder a broader application. In this work, the authors aim to contribute to a safer introduction of e-voting tools by applying a practical evaluation framework strongly based on the security requirements issued by the Council of Europe (CoE) in 2017 to nvotes,...
-
Techno-economic assessment of cooperation of hybrid renewable energy sources with hydrogen storage
PublicationThe paper presents a technical and economic analysis of the power supply for a model industrial facility with the use of the most promising renewable energy sources (RES), supported by a hydrogen energy storage. This scenario was compared with the variants of supplying the facility directly from the grid and from RES without energy storage. A strategy was proposed for powering the plant aimed at maximising self-consumption of self-generated...
-
DoA Estimation Using Reconfigurable Antennas in Millimiter-Wave Frequency 5G Systems
PublicationTo achieve low latency and high throughputs, future 5G systems will have to utilize complex antenna systems able to provide beamforming and direction-of-arrival (DoA) estimation capabilities. Most of the concepts available in the literature rely on analog or digital beamforming, which is well developed and can be used both at a base station and in a user terminal. However, in applications, in which...
-
Iterative Global Sensitivity Analysis Algorithm with Neural Network Surrogate Modeling
PublicationGlobal sensitivity analysis (GSA) is a method to quantify the effect of the input parameters on outputs of physics-based systems. Performing GSA can be challenging due to the combined effect of the high computational cost of each individual physics-based model, a large number of input parameters, and the need to perform repetitive model evaluations. To reduce this cost, neural networks (NNs) are used to replace the expensive physics-based...