Filters
total: 3585
filtered: 2785
displaying 1000 best results Help
Search results for: REMELTED LAYER
-
Cavitation erosion behavior of 18/8 stainless steel after its laser alloying of manganese
PublicationW pracy przedstawiono wyniki badań własności kawitacyjnych stali nierdzewnej gatunku 18/8 po jej laserowym stopowaniu różną zawartością manganu. Stwierdzono, że przy zawartości Mn w ilości 7,13% występuje największy wzrost twardości po stopowaniu a głębokość umacniania na skutek działania obciążeń kawitacyjnych jest najmniejsza.
-
Anodic titania nanotubes decorated with gold nanoparticles produced by laser-induced dewetting of thin metallic films
PublicationHerein, we combine titania layers with gold species in a laser-supported process and report a substantial change of properties of the resulting heterostructures depending on the major processing parameters. Electrodes were fabricated via an anodisation process complemented with calcination to ensure a crystalline phase, and followed by magnetron sputtering of metallic films. The obtained TiO2 nanotubes with deposited thin (5, 10...
-
Modeling DAC Application Execution Time
PublicationAn application written in the Divide And Conquer paradigm is more difficult to model than SPMD application because of complex algorithm, causing use of many coefficients in a computational complexity function. Processors are divided into various layers, each layer contains different number of processors. Data packets processed in different layers and transferred between layers have different length. Moreover first layer processors use...
-
Low-power microwave-induced fabrication of functionalised few-layer black phosphorus electrodes: A novel route towards Haemophilus Influenzae pathogen biosensing devices
PublicationIn this paper, various passivation schemes were applied at few-layer black phosphorus (FLBP) to achieve covalent functionalisation with 4-azidobenzoic acid, improving its electrochemical response intended for analytical and biosensing applications. The thermal and microwave assisted modification procedures in toluene and dime-thylformamide resulted in high reversibility of reactions on functionalised FLBP using a ferricyanide/ferrocya-nide...
-
Improvement of the Water Resistance of a Narrow-Band Red-Emitting SrLiAl3N4:Eu2+Phosphor Synthesized under High Isostatic Pressure through Coating with an Organosilica Layer
Publication -
The effect of strain rate on the passive layer cracking of 304L stainless steel in chloride solutions based on the differential analysis of electrochemical parameters obtained by means of DEIS
PublicationOkreślono wpływ szybkości rozciągania w zakresie 10-5s-1 ÷ 16∙10-5s-1 na niestacjonarny proces elektrochemiczny pękania warstwy pasywnej. Badania przeprowadzono na stali wysokostopowej 304L w temperaturze pokojowej w środowisku chlorków za pomocą dynamicznej elektrochemicznej spektroskopii impedancyjnej (DEIS). W rezultacie uzyskano zestaw chwilowych widm impedancyjnych odzwierciedlających dynamikę badanego układu korozyjnego....
-
Simulation investigation of perovskite-based solar cells
PublicationThree models of thin-layer lead-halide perovskite solar cells with different electron-transport layers (TiO2,SnO2,ZnO) were investigatedby the simulation method. The perovskite layer thickness was optimized for all the systems. The analysis of the standard photovoltaic cell performanceparameters at various operating temperatures was performed. The best performance was achieved for the system with theSnO2conductive layer.
-
Rubrene Thin Films with Viably Enhanced Charge Transport Fabricated by Cryo-Matrix-Assisted Laser Evaporation
PublicationAmong organic semiconductors, rubrene (RB; C42H28) is of rapidly growing interest for the development of organic and hybrid electronics due to exceptionally long spin diffusion length and carrier mobility up to 20 cm2V−1s−1 in single crystals. However, the fabrication of RB thin films resembling properties of the bulk remains challenging, mainly because of the RB molecule’s twisted conformation. This hinders the formation of orthorhombic...
-
The pulsed laser ablation synthesis of colloidal iron oxide nanoparticles for the enhancement of TiO2 nanotubes photo-activity
PublicationThe rapid, only a few minutes long synthesis of FeO, Fe3O4, and Fe2O3nanoparticles mixture utilizing the pulsedlaser ablation using simply pure iron target and water was demonstrated. The size and crystal phase of Fe-basedNPs were characterized using DLS and HR-TEM techniques, respectively. The metastable suspension of FeO,Fe3O4, and Fe2O3nanoparticles was used to the decoration of anodized TiO2nanotubes (TiO2-NTs) by means ofthe...
-
Synthesis, structural characterization, and thermal properties of Ca‐ and La‐doped soda‐lime glasses by laser melting
PublicationLaser melting techniques have been used in the preparation of unconventional glass compositions with high melting temperatures. Thus, we wanted to test the feasibility of using a CO2 laser in the preparation of nitrogen-rich oxynitride glasses and nitride silicate glasses. Melting from oxides and metallic raw materials, we wanted to study first glass formation and possible evaporation losses of the glass components. Two glass series...
-
The In-Depth Studies of Pulsed UV Laser-Modified TiO2 Nanotubes: The Influence of Geometry, Crystallinity, and Processing Parameters
PublicationThe laser processing of the titania nanotubes has been investigated in terms of morphology, structure, and optical properties of the obtained material. The length of the nanotubes and crystallinity, as well as the atmosphere of the laser treatment, were taken into account. The degree of changes of the initial geometry of nanotubes were checked by means of scanning electron microscopy, which visualizes both the surface and the cross-section....
-
Application of Msplit method for filtering airborne laser scanning data sets to estimate digital terrain models
PublicationALS point cloud filtering involves the separation of observations representing the physical terrain surface from those representing terrain details. A digital terrain model (DTM) is created from a subset of points representing the ground surface. The accuracy of the generated DTM is influenced by several factors, including the survey method used, the accuracy of the source data, the applied DTM generation algorithm, and the survey...
-
Laser induced formation of copper species over TiO2 nanotubes towards enhanced water splitting performance
PublicationWe proposed fast and scalable route where the ordered TiO2 nanotubes coated with thin copper layers were annealed by the laser beam of 355 nm wavelength at different fluencies in the range of 15–120 mJ/cm2. As a result, copper species are integrated with the titania substrate and the formed material exhibits unique optical absorption bands in the visible range. Moreover, X-ray photoelectron spectroscopy analysis reveals the formation...
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublicationSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Introductory investigations of dermatologic diode laser with wavelengths 975 nm: clinical therapy of Recklinghausen disease and of hemangiomas
Publication -
Evaluation of Surface Topography after Face Turning of CoCr Alloys Fabricated by Casting and Selective Laser Melting
Publication -
Emerging Role of Adenylate Kinase 4 as a Metabolic Player Regulating Cellular Hypoxic Responses in Pulmonary Cells
Publication -
Novel Quaternary TlGaSn2Se6 Single Crystal as Promising Material for Laser Operated Infrared Nonlinear Optical Modulators
Publication -
Impact of European vaccination policies on seasonal influenza vaccination coverage rates: An update seven years later
Publication -
QEEG-based neural correlates of decision making in a well-trained eight-year-old chess player
Publication -
In-vivo monitoring of oxygen saturation in murine carcinoma during PDT by diode laser light diffuse reflectance
Publication -
FPGA-based LLRF control module for x-ray free electron laser and TESLA feedback system
Publication -
A Systematic and Comparative Study of Binary Metal Catalysts for Carbon Nanotube Fabrication Using CVD and Laser Evaporation
Publication -
ROYAL CHAPEL IN GDANSK. STUDY OF FACILITY INVENTORY WITH THE USAGE OF LASER SCANNING WITHIN THE FRAMES OF STUDENT PROJECT
PublicationThis article presents the photogrammetric works carried out during the architectural inventory of the Royal Chapel in the Main Town of Gdansk (Poland). The facility has the status of a monument of architecture and since decades it is covered by geodetic monitoring, realized with the participation of the Department of Geodesy of Faculty of Civil and Environmental Engineering of Gdańsk University of Technology . For several years,...
-
CFD COUPLING OF VOF MODEL WITH ARRHENIUS EQUATION FOR ANALYSIS OF LASER-INDUCED THERMAL DEACTIVATION OF E. COLI
PublicationUnderstanding bacterial deactivation at the micro-scale, particularly with E. coli, is crucial for advancing microbiology and has promising applications in biomedical research. In this research contribution, we investigate the thermal inactivation of E. coli bacteria using gold nanoparticles irradiated by a green 1-W laser within a microfluidic chamber. The microfluidic device comprises a fluidic chamber filled with a thin film...
-
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublicationThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Antibacterial properties of laser-encapsulated titanium oxide nanotubes decorated with nanosilver and covered with chitosan/Eudragit polymers
PublicationTo provide antibacterial properties, the titanium samples were subjected to electrochemical oxidation in the fluoride-containing diethylene glycol-based electrolyte to create a titanium oxide nanotubular surface. Afterward, the surface was covered by sputtering with silver 5 nm film, and the tops of the nanotubes were capped using laser treatment, resulting in an appearance of silver nanoparticles (AgNPs) of around 30 nm in diameter...
-
Evaluation of apparent Young׳s modulus of the composite polymer layers used as sliding surfaces in hydrodynamic thrust bearings
PublicationHydrodynamic bearings with a polymer sliding layer are able to operate in severe conditions, mainly due to favorable properties of the polymers. The goal of this research was to evaluate apparent Young׳s modulus of two types of the polymer composite layers used for sliding surfaces in hydrodynamic bearings, as a function of temperature. The Young׳s modulus was evaluated on the basis of compression tests carried out on samples obtained...
-
Effect of buffer layers on performance of organic photovoltaic devices based on copper phthalocyanine-perylene dye heterojunction
PublicationPraca przedstawia wyniki badań układu fotowoltaicznego złożonego z cienkich warstw organicznych tworzących złącze (CuPc i MePTCDI), elektrod (ITO i Ag) oraz z warstw buforowych (MoO3 przy ITO i BCP przy Ag).
-
Morfologia warstw napawanych plazmowo na bazie kobaltu. (Morfology of cobalt base PTA cladding layers)
PublicationPrzedmiotem badań była struktura napawanych plazmowo warstw na bazie kobaltu, które spełniają funkcję powłok naprawczych na grzybkach zaworów silników okrętowych. Określono mikrostrukturę, mikrotwardość na przekroju warstwy oraz rozkład pierwiastków w różnych obszarach napoiny.
-
Area-Averaged Surface Moisture Flux over Fragmented Sea Ice: Floe Size Distribution Effects and the Associated Convection Structure within the Atmospheric Boundary Layer
Publication -
Expanded graphite assistant construction of gradient-structured char layer in PBS/Mg(OH)2 composites for improving flame retardancy, thermal stability and mechanical properties
Publication -
Warstwowa ocena epidemiologiczna architektury zakładów opiekuńczo-leczniczych i zakładów gieriatycznych = Layer based epidemiological quality assessment of architecture of care security and geriatric wards
PublicationW artykule opisano możliwość wykorzystania autorskiej metody warstwowej oceny epidemiologicznej (WOE) do oceny potencjalnego ryzyka zakażeń w obiektach przeznaczonych dla osób starszych. Materiał i metody: W celu weryfikacji możliwości użycia metody WOE do oceny zagrożeń w zakresie bezpieczeństwa epidemiologicznego środowiska zbudowanego poddano analizie dostępne źródła literatury związane z obowiązującymi w Polsce wymaganiami...
-
Properties comparison of rubber and three layer PTFE-NBR-bronze water lubricated bearings with lubricating grooves along full bush circumference based on experimental tests
PublicationWater lubricated bearings have been in industrial use for well over a century. During the last decade their traditional range has been expanded with new, modern products. Despite that fact, certain solutions continue to employ the standard rubber bearing with lubricating grooves located along entire bush circumference. The work presents experimental research conducted on comparable sliding bearings with lubrication grooves along...
-
Wpływ stanu warstwy wierzchniej na mikrostrukturę i właściwości korozyjne stopu SUPERSTON = Influence of the state of surface layer on microstructure and corrosion properties of SUPERSTON alloy
PublicationW artykule przedstawiono rezultaty nadtapiania laserowego w warunkach kriogenicznych stopu SUPERSTON. Dokonano oceny mikrostruktury powierzchni i przekroju stopu SUPERSTON po obróbce laserowej. Określono właściwości stopu, które porównano ze stanem powierzchni po nadtapianiu oraz nadtapianiu i szlifowaniu.
-
The Impact of Material Selection on Durability of Exhaust Valve Faces of a Ship Engine – A Case Study
Publicationwo alloys were used in order to extend the service life of marine engine exhaust valve head. Layers of cobalt base alloys were made of the powders with with chemical composition as follow: the layer marked L12; C-1,55%; Si-1,21%; Cr-29,7%; W-9%; Ni-2%; Mo<0,01%; Fe-1,7%; Co-54,83% and the layer marked N; C-1,45%; Co-38,9%; Cr-24,13%; Ni-10,43%; W-8,75%; Fe-7,64%; Mo-7,56%; Si-2,59%. Base metal was valve steel after heat treatment....
-
Surface characteristics of glass fibres covered with an aluminum layer after a chemical modification process using secondary ion mass spectrometry (SIMS) and atomic force microscopy (AFM)
PublicationPrzedstawiono wyniki z badań powierzchni modyfikowanych włókien szklanych (przed i po procesie chemicznej modyfikacji ich powierzchni), które są kandydatem na przyszły oryginalny bezmatrycowy materiał odniesienia lotnych analitów etenu (C2H4) metodami spektrometrii mas jonów wtórnych oraz mikroskopii sił atomowych. Badania miały na celu obserwację zmian oraz procesów, jakie zaszły na powierzchni włókien szklanych pokrytych...
-
A Comparative Quantitative Structure-Retention Relationships Study for Lipophilicity Determination of Compounds with a Phenanthrene Skeleton on Cyano-, Reversed Phase-, and Normal Phase-Thin Layer Chromatography Stationary Phases
Publication -
Application of multivariate mathematical-statistical methods to compare reversed-phase thin-layer and liquid chromatographic behaviour of tetrazolium salts in Quantitative Structure-Retention Relationships (QSRR) studies
Publication -
Combined computational-experimental approach to predict blood–brain barrier (BBB) permeation based on “green” salting-out thin layer chromatography supported by simple molecular descriptors
Publication -
Analiza budowy i własności napoiny wykonanej z proszku 1606 ze stopu kobaltu = Morphology and property analyze of the layer made of 1606 powder of cobalt alloy
PublicationW pracy analizowano budowę i zmiany zachodzące w strukturze napawanej laserowo warstwy wykonanej ze stopu kobaltu pod wpływem korozyjnego środowiska gazów spalinowych. Warstwa wykazywała się znaczną niejednorodnością chemiczną i składem różnym od założonego jednakże te nieprawidłowości nie wpłynęły znacząco na jej odporność korozyjną w gorących gazach spalinowych.
-
Monolithically p-down nitride laser diodes and LEDs obtained by MBE using buried tunnel junction design
Publication -
Improvement of Oxygen Electrode Performance of Intermediate Temperature Solid Oxide Cells by Spray Pyrolysis Deposited Active Layers
PublicationIntermediate temperature solid oxide fuel cells oxygen electrodes are modified by active interfacial layers. Spray pyrolysis is used to produce thin (≈500 nm) layers of mixed ionic and electronic conductors: Sm0.5Sr0.5CoO3−δ (SSC), La0.6Sr0.4CoO3−δ (LSC), La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF), and Pr6O11 (PrOx) on the electrode–electrolyte interface. The influence of the annealing temperature on the electrode polarization (area specific...
-
Study on Microstructure and Mechanical Properties of Laser Welded Dissimilar Joint of P91 Steel and INCOLOY 800HT Nickel Alloy
PublicationThis investigation attempts to explore the weld characteristics of a laser welded dissimilar joint of ferritic/martensitic 9Cr-1Mo-V-Nb (P91) steel and Incoloy 800HT austenitic nickel alloy. This dissimilar joint is essential in power generating nuclear and thermal plants operating at 600–650 °C. In such critical operating conditions, it is essential for a dissimilar joint to preserve its characteristics and be free from any kind...
-
The Influence of Drying Temperature on Color Change of Hornbeam and Maple Wood Used as Surface and Inner Layers of Wood Composites
PublicationThe thermal treatment of wood changes its structure due to the degradation of wood polymers (cellulose, hemicellulose and lignin), so the physical properties of wood are either improved or degraded. Color changes apply not only to natural wood, but also to such wood composites for which some amount of glue is used in their construction (e.g., plywood, blockboard or laminboard). This article is focused on the analysis of hornbeam...
-
Pulsed Laser Deposition of Bismuth Vanadate Thin Films—The Effect of Oxygen Pressure on the Morphology, Composition, and Photoelectrochemical Performance
PublicationThin layers of bismuth vanadate were deposited using the pulsed laser deposition technique on commercially available FTO (fluorine-doped tin oxide) substrates. Films were sputtered from a sintered, monoclinic BiVO4 pellet, acting as the target, under various oxygen pressures (from 0.1 to 2 mbar), while the laser beam was perpendicular to the target surface and parallel to the FTO substrate. The oxygen pressure strongly affects...
-
Kinetics of molecular decomposition under irradiation of gold nanoparticles with nanosecond laser pulses—A 5-Bromouracil case study
PublicationABSTRACT Laser illuminated gold nanoparticles (AuNPs) efficiently absorb light and heat up the surrounding medium, leading to versatile applications ranging from plasmonic catalysis to cancer photothermal therapy. Therefore, an in-depth understanding of the thermal, optical, and electron induced reaction pathways is required. Here, the electrophilic DNA nucleobase analog 5-Bromouracil (BrU) has been used as a model compound to...
-
The bismuth vanadate thin layers modified by cobalt hexacyanocobaltate as visible-light active photoanodes for photoelectrochemical water oxidation
PublicationBismuth vanadate thin films deposited using the pulsed laser deposition technique were modified using cobalt hexacyanocobaltate (Cohcc). The 2-step method of Cohcc nanocubes preparation was applied: i) metallic cobalt deposition and ii) cobalt electrooxidation in Co(CN)63− containing electrolyte. The presence of CN stretching vibrations was confirmed by Raman spectroscopy. The energy band gap was equal to 2.5 eV and was estimated...
-
Laser granulometer as an useful tool for selection of appropriate membranes used in the MIEX®DOC-UF/MF hybrid process
PublicationIn the study, particle size distribution of the MIEX® resin was presented. Such analyses enable to determinate whether presence of fine resin fraction may be the reason for unfavorable membrane blocking during water purification by the hybrid MIEX®DOC-microfiltration/ultrafiltration systems. Granulometric analysis of resin grains using the laser diffraction particle size analyzer (laser granulometer) was carried out as well as...
-
Kinetics of molecular decomposition under irradiation of gold nanoparticles with nanosecond laser pulses—A 5-Bromouracil case study
Publication