Filters
total: 2309
filtered: 1889
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: DISINTEGRATION-BOILING
-
Analytical approach for membrane action in laterally-restrained reinforced concrete square slabs under uniformly distributed loads
PublicationLaterally-restrained reinforced concrete slabs can mobilise compressive membrane action and subsequent tensile membrane action under extreme loading conditions, thereby enhancing the load resistance under uniformly distributed loads. Previous analytical study focuses primarily on tensile membrane action in simply-supported slabs. This paper describes an analytical approach for membrane action in laterally-restrained square slabs....
-
Characterization of fracture process in polyolefin fibre-reinforced concrete using ultrasonic waves and digital image correlation
PublicationThis study explores the monitoring of the fracture process in concrete beams and aims to characterize the evolution of damage in polyolefin fibre-reinforced concrete beams by utilizing the integrated application of two measurement techniques, digital image correlation and ultrasonic testing. The interpretation of registered wave time histories data was provided by the calculation of the magnitude-phase-composite metrics. An efficient...
-
Standard and modified falling mass impact tests on preplaced aggregatefibrous concrete and slurry infiltrated fibrous concrete
PublicationAlthough several studies have been conducted to evaluate the impact response of concrete using theAmerican Concrete Institute (ACI) 544-2R falling mass impact test, the variations in test results are themain drawback of this testing method. This study aims to reduce the variations in experimental impacttest results by introducing two simple test setup modifications; (1) using coarse or fine aggregate bed-ding as an alternative...
-
Mechanical, durability, depolluting and electrical properties of multifunctional mortars prepared with commercial or waste carbon-based fillers
PublicationCarbon-based fillers from industrial wastes and commercial ones were compared to improve the properties of lime-based mixes. As commercial fillers, graphene nanoplatelets and activated carbon were used, whereas as industrial wastes a char obtained by the gasification of biomasses and a used foundry sand were chosen. Carbon-based wastes were found to be a good cost-effective alternative to commercial carbon based fillers to increase...
-
Asphalt concrete subjected to long-time loading at low temperatures – Deviations from the time-temperature superposition principle
PublicationThe article presents the observed deviations from the time-temperature superposition principle of asphalt concretes, tested in the bending beam creep test at low temperatures for a long time of loading. In almost all tested asphalt concretes, deviations appeared after 500 s of loading at the temperature of -10 C. Some types of bitumen presented deviations at other temperatures – usually the harder the grade of the bitumen, the...
-
Ground tire rubber thermo-mechanically devulcanized in the presence of waste engine oil as asphalt modifier
PublicationCross-linked elastomers network is main limitation for industrial usage of ground tire rubber (GTR) as asphalts’ and road pavements modifier. GTR was thermo-mechanically devulcanized via extrusion in the presence of waste engine oil (WEO) at temperature ranges from 150 to 280 °C. Combined impact of WEO content and extruder barrel temperature on the change of cross-linked structure of degraded GTR (DTGR) was investigated through...
-
Impact and stretching standardized tests as useful tools for assessment of viscoelastic behavior for highly rubberized asphalt binder
PublicationAsphalt binder is generally identified as a brittle material at low service temperature or under high-speed load, and the brittleness becomes serious after weathering aging. Improving the toughness of asphalt binder through adding high-content of crumb tire rubber is an efficient method to solve this problem. Devulcanized rubber modified asphalt binder (DRMA) with different contents (15–40%) of devulcanized rubber (DR) were prepared...
-
Simple empirical formula to estimate the main geomechanical parameters of preplaced aggregate concrete and conventional concrete
PublicationPreplaced aggregate concrete (PAC) or two-stage concrete is a specific type of concrete successfully employed in many projects including underwater concrete structures, massive concrete structures, structures made of reinforced concrete, and improvement of concrete structures. PAC is significantly different than the conventional concrete. In this type of concrete, aggregates are initially poured into the mold, the voids between...
-
Preliminary study of linear viscoelasticity limits of cold recycled mixtures determined in Simple Performance Tester (SPT)
PublicationThe publication presents methodology developed for determination of linear viscoelasticity limits for cold recycled mixtures with cement and bituminous emulsion using Simple Performance Tester (SPT). Methodology was verified on reference materials (PCV and steel dummy specimens, cement concrete and asphalt concrete) to comply with elasticity and viscoelasticity theory. The developed methodology enabled determination of linear viscoelasticity...
-
A novel heterogeneous model of concrete for numerical modelling of ground penetrating radar
PublicationThe ground penetrating radar (GPR) method has increasingly been applied in the non-destructive testing of reinforced concrete structures. The most common approach to the modelling of radar waves is to consider concrete as a homogeneous material. This paper proposes a novel, heterogeneous, numerical model of concrete for exhaustive interpretation of GPR data. An algorithm for determining the substitute values of the material constants...
-
Hydrogen embrittlement of X2CrNiMoCuN25-6-3 super duplex stainless steel welded joints under cathodic protection
PublicationThe effect of cathodic polarization conditions on hydrogen degradation of X2CrNiMoCuN25-6-3 super duplex stainless steel welded joints, obtained using flux cored arc and submerged arc welding methods, was evaluated. Slow strain rate tensile tests of base material and welded specimens, ferrite content measurements, scanning electron microscopy observations, and statistical analysis were performed. It was found that hydrogenation...
-
The influence of combination of binding agents on fatigue properties of deep cold in-place recycled mixtures in Indirect Tensile Fatigue Test (ITFT)
PublicationThe publication presents fatigue properties of cold recycled mixtures for eight combinations of binding agents (cement and bituminous emulsion). Cold recycled mixtures were evaluated in Indirect Tensile Fatigue Test (ITFT) at the temperature of 20 C in controlled stress mode. As a function of horizontal stress, fatigue life is strongly influenced by combination of the binding agents. When fatigue life is analyzed as a function...
-
A COMPREHENSIVE REVIEW OF LIFE CYCLE ASSESSMENT AND ENERGY EFFICIENCY IN 3D PRINTING FOR CONSTRUCTION: CURRENT STATE, BENEFITS, LIMITATIONS, AND FUTURE OUTLOOK
PublicationThe agenda of Industry 4.0 strongly affects design and construction at all its phases, and three-Dimensional Printing (3DP) is an essential part of it. The emerging technology has the potential to become a more valid and accepted form of construction. This research is based on a literature review regarding the relationships between the concepts of Life Cycle Assessment (LCA) and energy efficiency for 3DP in construction research...
-
Investigations on fracture in reinforced concrete beams in 3-point bending using continuous micro-CT scanning
PublicationThis study explores a fracture process in rectangular reinforced concrete (RC) beams subjected to quasi-static three-point bending. RC beams were short and long with included longitudinal reinforcement in the form of a steel or basalt bar. The ratio of the shear span to the effective depth was 1.5 and 0.75. The focus was on the load–deflection diagram and crack formation. Three-dimensional (3D) analyses of the size and distribution...
-
Experimental investigations on water sorptivity in mortars with the use of X-ray micro-CT system.
PublicationW pracy doswiadczalnej zbadano zjawisko sorpcji wody w pryzmatycznych próbkach zapraw, które jest ściśle powiązane z trwałością materiału. Sorpcyjność oceniana na etapie ustalonym w połączeniu z warunkami zewnętrznymi może być wykorzystana do przewidywania okresu użytkowania. Sorpcyjność początkową i wtórną wody w próbkach zapraw nienasyconych zmierzono w badaniach laboratoryjnych zgodnie z normą amerykańską ASTM C 1585–04. Wpływ...
-
Changes in Functional and Spatial Layouts of Polish Single-Family Houses
PublicationArticle presents the evolution of functional and spatial layouts of single-family houses in Poland, with particular emphasis on the functions of a contemporary house. Singlefamily housing constitutes a significant part of the construction market in Poland. The way of forming functions in single-family buildings in the historical cycle has characteristic features resulting from the culture of the society in a given period. The functional...
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublicationA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
Application of the Chimney Cap as a Method of Improving the Effectiveness of Natural Ventilation in Buildings
PublicationAdequately designed natural ventilation is the cheapest and easiest way to effectively remove indoor pollutants and keep the air inside a building fresh. A prediction of the performance and effectiveness of ventilation in order to determine the design of a ventilation system can provide real and long-term cost savings. The worst time in terms of the efficiency of natural ventilation is the spring-autumn transition period [7]. In...
-
Studies of Nonlinear Sound Dynamics in Fluids Based on the Caloric Equation of State
PublicationThe sound speed and parameters of nonlinearity B/A, C/A in a fluid are expressed in terms of coefficients in the Taylor series expansion of an excess internal energy, in powers of excess pressure and density. That allows to conclude about features of the sound propagation in fluids, the internal energy of which is known as a function of pressure and density. The sound speed and parameters of nonlinearity in the mixture consisting...
-
ENVIRONMENTALLY FRIENDLY MATERIALS IN ARCHITECTURE � MODERN TRENDS AND DEVELOPMENT DIRECTIONS
PublicationFor a long time the interest in environmentally friendly materials in architecture is no longer limited to the use of renewable and natural substances such as wood, stone, straw, or reusable materials, such as metals or glass. Today the so-called naturals and the materials compatible with the idea of sustainability constantly appear on the market in new forms. Increasing awareness of the necessity to limit the building sector’s...
-
Elastic waves in the railroad track substructures and its surroundings analyzed with non-classical operational methods
PublicationWe analyze the propagation of the waves generated by the rolling stock and the interaction of those waves on the medium and its surroundings. We use non-classical operational methods for monitoring construction of the railway infrastructure and for noise damping.
-
Inlet air fogging of marine gas turbine in power output loss compensation
PublicationThe use of inlet air fogging installation to boost the power for gas turbine engines is widely applied in the power generation sector. The application of fogging to mechanical drive is rarely considered in the literature [1]. This paper will cover some considerations relating to its application to gas turbines in ship drive. There is an important evaporative cooling potential throughout the world when the dynamic data is evaluated,...
-
The role of investments in economic development
PublicationIn the modern world, one may observe diversification of economies of given countries. Many of them, considered to be less developed,are aspiring to diminish the gap between them and well developed countries, one of such countries is Poland, which is trying hard to boots its competitive position in the worldwide market and achieve the constant and well-balanced development. It can be attained by building knowledge economy. Therefore,...
-
Between Descriptive Geometry and CAD 3D
PublicationDescriptive geometry provides methods to analyse three-dimensional space through two-dimensional drawings and prepares to create technical documentation. Geometric form of an engineering project is presented by the means of projection methods based on a 3D model, which is present in designer’s imagination. The forthcoming era of Building Information Modelling (BIM) brings changes in the way the engineer works, as the vision is...
-
LOW NOISE TIRES FOR HYBRID AND ELECTRIC VEHICLES
PublicationLow Emission Vehicles that are hybrid and electric cars may benefit from specially designed tires that are optimized for driving conditions typical for such vehicles. It is possible that in the future Low Emission Vehicles, especially passenger cars, will substitute conventional vehicles in all applications, however for the time being they are mostly used in urban and suburban areas. Urban traffic has a rather low demand for grip...
-
Selection of circuit geometry for miniaturized microwave components based on concurrent optimization of performance and layout area
PublicationThe paper presents a framework for automated EM-driven circuit geometry selection of miniaturized microwave components. Selection of a particular layout is based directly on miniaturization rates achieved for a set of candidate circuit geometries. Size reduction of the considered structures is obtained by replacing their main building blocks (i.e., conventional transmission lines) with slow-wave composite cells and meander lines....
-
Surface Roughness Evaluation in Thin EN AW-6086-T6 Alloy Plates after Face Milling Process with Different Strategies
PublicationLightweight alloys made from aluminium are used to manufacture cars, trains and planes. The main parts most often manufactured from thin sheets requiring the use of milling in the manufacturing process are front panels for control systems, housing parts for electrical and electronic components. As a result of the final phase of the manufacturing process, cold rolling, residual stresses remain in the surface layers, which can influence...
-
A conceptual design and numerical analysis of the mixerless urea-SCR system
PublicationIn the present study, an innovative design of the urea-selective catalytic reduction (SCR) system without conventional mixing elements was developed. The aim was to obtain a high degree of urea decomposition, and uniform ammonia distribution at the inlet to the catalyst, while minimising the liquid film deposition and keeping the compact design. The concept of the design was based on creating high turbulences and elongating...
-
Three phase transient model of wet coal pyrolysis
PublicationA one-dimensional transient mathematical model was developed to describe the thermal and flow phenomena during coal pyrolysis in a coke oven. The model was solved numerically using partly implicit methods for gas flow and heat transfer problems. It was successfully validated with industrial-scale measurements of temperature change in the middle-plane of the coke oven chamber. The evolution of temperature and pressure, distributions...
-
Investigations of Aerodynamics of Tesla Bladeless Microturbines
PublicationThe paper presents an analysis of a Tesla bladeless turbine for a co-generating micro-power plant of heat capacity 20 kW, whichoperates in an organic Rankine cycle with a low-boiling medium. Numerical calculations of flow in several Tesla turbine models areperformed for a range of design parameters. Results of investigations exhibit interesting features in the distribution of flowparameters within the turbine interdisk space. The...
-
Efficient Selenenylation of Malonates Using Bis(phosphorothioyl) Diselenide
PublicationBis(O,O-diisopropoxyphosphinothioyl) diselenide reacts readily and quickly with the sodium salt of malonates to give quantitatively stable sodium 2-(O,O-diisopropyl phosphorothioselenenyl)propanedioates. No traces of the corresponding C,C-diselenenylation products were detected. A standard aqueous workup procedure affords the products, albeit in poor yield (about 45%). It was proved that the reaction is reversible due to the presence...
-
DESIGN AND THEORETICAL ANALYSIS OF A PROTOTYPE TILTING-PAD RADIAL BEARING WITH ADJUSTABLE CLEARANCE
PublicationThe article introduces a design and analysis results of a prototype ORC (organic Rankine cycle) turbo generator rotor assembly of 300kW power, supported by tilting-pad bearings of original design. The calculations were performed for a prototype turbo generator rotor. The shaft of this machine is supported with two radial bearings, lubricated with an unusual lubricant – a low-boiling-point agent. The main objective of the presented...
-
Badania stanu technicznego ścianek szczelnych strony południowej i północnej komory południowej śluzy Dzierżno
PublicationPrace dotyczyły badań nieniszczących łączników (zamków) Paine`a oraz ścianek szczelnych. Ściany boczne komory południowej śluzy Dzierżno zbudowane są ze stalowych pasów blachy o grubości około 16mm i długości 22m połączonych ze sobą wzdłuż dłuższej krawędzi za pomocą zamków Peine`a. System ten umożliwia uzyskanie szczelnego połączenia na całej długości ścianki. Zaawansowany proces korozji spowodował rozszczelnienie połączenia...
-
Comparison of new position estimation algorithm for indoor environment
PublicationIn the paper a new position estimation algorithm based on distance measurements is presented. This algorithm is dedicated for indoor environments. In the paper the new algorithm is compared with Chan algorithm. For the comparison were used real measurements conducted inside a building.
-
System of innovation: a sectoral approach
Publicationthe article presents a systems approach to innovation as an alternative method of assessing the sector innovativeness. in the article the building blocks of each sectoral system of innovations (ssi) such as a knowledge base, institutions and actors are discussed. moreover, the five models of ssi are presented.
-
Evaluation of Pavement Temperatures in Poland During Winter Conditions
PublicationThe paper presents the analysis of pavement temperatures from meteorological stations located at the Polish national roads during the impact of low winter temperatures. Presented issue is particularly important in view of the problem of low-temperature cracks that occur in the asphalt pavement under the influence of low temperatures. For each location of meteorological station there were analysed measurements of the temperature...
-
Modeling of wood frame structures with different insulation materials under damaging dynamic loading
PublicationWood frame buildings are very popular in regions that are exposed to different dynamic excitations, such as damaging earthquakes. Their seismic resistance is really important in order to prevent structural damages and human losses. This paper presents the results of advanced numerical investigation carried out using the FEM. Based on the models of wall panels, the numerical model of real structure of the wood frame building has...
-
The Possibilities of Improving the Fatigue Durabilityof the Ship Propeller Shaft by Burnishing Process
PublicationHeavily loaded structural elements operating in a corrosive environment are usuallyquickly destroyed. An example of such an element is a ship propeller operating in a seawaterenvironment. This research presents a fatigue resistance test performed on elements operating inseawater. Different processing parameters applied on the samples in particular were compared withthe specimens whose surface had been burnished differently and...
-
Retrofitted vibro-pressed pavement bricks and their impregnation in modern architecture.
PublicationRecent construction projects require new properties of concrete building materials. The paper describes the technological methods of retrofitting of vibro-pressed concrete pavement brick and shows the results of improving physical properties of concrete by application of different impregnation agents.
-
Optimizing of target detection and tracking processes realized on consoles of passive sonar with linear towed antenna
PublicationThe long-range passive towed sonar was first modernised a few years ago. Building on operator experience over that period, a concept was developed of optimising the tasks performed by sonar operators, and improving forms of imaging to inform about object detection and support object tracking. The concept was implemented and successfully tested during ships’ manoeuvres. The optimisation of operator tasks was designed to keep listening...
-
Koncepcja, modelowanie i symulacja układu napędowego prototypu samochodu elektrycznego "ELV001"
PublicationAbstract: In this paper a conception, modelling and simulation tool for drive system of the prototype electric vehicle ''ELV001'' have been presented. The design and building of this vehicle have been carried out in frame of the project: ''Building a market of electric vehicle and charging infrastructure - fundamentals of energy safety''. The simulation tools are of great assistance to engineers and researchers to reduce product-development...
-
ortho-Fluorobenzanilides and ortho-fluorothiobenzanilides: Molecular conformations and crystal packing
PublicationSeries of 2-fluoro and 2,6-difluorobenzanilides and their thiobenzanilide analogs have been synthesized to investigate the influence of the fluorine atom on their crystal structures and self-assembly in the crystal lattice. The X-ray analysis of the single crystal revealed that the synthesized molecules adopt a geometry being deflected from planarity. The deflection was investigated by analysis of dihedral angles between mean planes...
-
ASSESSMENT OF NATURAL VENTILATION SYSTEM FOR A TYPICAL RESIDENTIAL HOUSE IN POLAND
PublicationThe paper presents the research results of field measurements campaign of natural ventilation performance and effectiveness in a residential building. The building is located in the microclimate whose parameters differ significantly in relation to a representative weather station. The measurement system recorded climate parameters and the physical variables characterizing the air flow in the rooms within 14 days of the winter season....
-
Path Loss Analysis for the IoT Applications in the Urban and Indoor Environments
PublicationThe Internet of Things (IoT) networks concept implies their presence in a various and untypical locations, usually with a disturbed radio signals propagation. In the presented paper an investigation of an additional path loss observed in an underground environment was described. The proposed measurement locations correspond to the operation areas of rapidly growing narrowband IoT (NBIoT) networks, the ones using the Long Term Evolution...
-
Przegląd układów hydraulicznych do otwierania i zamykania pokryw lukowych. Część II
PublicationOpisano konstrukcję i budowę pokryw lukowych przesuwnych typu rolling, piggy-back (''na barana''). Zamieszczono schematy hydrauliczne oraz opisano działanie mechanizmów do ryglowania, do niskiego i wysokiego podnoszenia oraz przesuwania pokryw.
-
The effect of depth of surface layers constituted by vacuum technologies on pitting
PublicationThe paper presents the results of a study of the effect of vacuum technologies of formation of surface layers on pitting of associated elements in a lubricated, heavy-load rolling contact. The study has shown that increase in a PVD coat depth is accompanied by decrease in the fatigue friction pair.
-
Recycling of Polyurethanes
PublicationPolyurethane waste can be recycled by mechanical methods (i.e., grinding and applying as a filler or pressing with a bonding agent) and chemical methods (mainly by e.g., glycolysis, hydrolysis, or aminolysis). There is also possibility to the recover energy from polyurethanes waste (by incineration, gasification, and pyrolysis).
-
Issues relating to the efficient Application of passive solar protection in multi-family residential buildings
PublicationThe following article is intended to discuss the issues concerning the introduction of passive measures aimed at improving solar protection in multi-family buildings. A system of classifying these methods into two groups of solutions (architectural and material-building) was applied. The first group includes issues concerning facade design, the spatial features of which (such as loggias, balconies and other overhangs) can be treated...
-
Wpływ kąta pochylenia koła na opór toczenia opon samochodowych
PublicationW pracy przedstawiono wpływ kąta pochylenia koła na opór toczenia opon do samochodów osobowych. Pomiary oporu toczenia kół toczących się z kątem pochylenia od -6º do +3º wykonano na bębnowej maszynie bieżnej metodą momentową. Wyniki pomiarów przedstawiono w formie zależności współczynnika oporu toczenia oraz przyrostu współczynnika oporu toczenia w funkcji kąta pochylenia badanego koła.
-
Review on friction stir welding of dissimilar magnesium and aluminum alloys: Scientometric analysis and strategies for achieving high-quality joints
PublicationMagnesium and aluminum alloys continually attract interest as lightweight structural materials for transport applications. However, joining these dissimilar alloys is very challenging. The main obstacle that hinders progress in dissimilar Mg-Al joining is the formation of brittle intermetallic compounds (IMCs). As a solid-state joining technique, FSW is an excellent candidate to attenuate the deleterious IMC effects in dissimilar...