Filters
total: 2837
filtered: 2229
-
Catalog
Chosen catalog filters
displaying 1000 best results Help
Search results for: LASER ALLOYING
-
Engineering Au nanoparticle arrays on SiO2 glass by pulsed UV laser irradiation
PublicationWe study semi-regular arrays of Au nanoparticles (NP) obtained via UV laser irradiation of thin Au films on glass substrate. The NP structures are prepared from films of a thickness up to 60 nm produced by discharge sputtering or pulsed laser deposition, and annealed by nanosecond laser pulses at 266 or 308 nm, respectively, at fluencies in the range of 60-410 mJ/cm2. For the rare- and close-packed NP structures, consistent description...
-
Preparation of porous TiO2 films by means of pulsed laser deposition for photocatalytic applications
PublicationIn this work the preparation and structure properties of porous thin films of TiO2 were investigated. The films were produced by means of the pulsed laser deposition technique using laser pulses at 266nm (10Hz) and at fluencies of 1-3.5J/cm2. The process was performed in vacuum using O2 buffer gas and films were deposited on the SiO2 glass or Si substrate. X-ray diffraction (XRD) and Raman analysis of the structure and chemical...
-
Investigations of Energy Conversion and Surface Effect for Laser-Illuminated Gold Nanorod Platforms
PublicationAchieving a quick temperature increase is a burning issue for biophysical applications, like germ inactivation and tumor ablation, and for energy performances, like solar collectors and steam generators. Based on the plasmon resonance phenomenon, noble metallic nanoparticles have emerged as promising weapons due to their very high biocompatibility, optical properties, and high surface-to-volume ratio, increasing energy conversion...
-
BACTERIAL INACTIVATION VIA LASER-DRIVEN GOLD NANOPARTICLE HEATING: SIMULATION AND ANALYSIS
PublicationThis study utilizes CFD technique to simulate the inactivation of E. coli bacteria within a microfluidic chamber, employing gold nanoparticles irradiated by a laser beam. Employing a single-phase model, the presence of bacteria is considered by treating thermal properties in the governing equations as effective, combining those of water and bacteria using established correlations from scientific literature. The conversion of light...
-
Cavitation erosion of chromium-manganese and chromium-cobalt coatings processed by laser beam
PublicationPrzedstawiono wyniki badań erozji kawitacyjnej napoin wykonanych za pomocą elektrod chromowo-manganowych i chromowo-niklowych oraz obrobionych wiązką lasera CO2 o mocy 1000 W. Próbki poddawano obciążeniom kawitacyjnym na stanowisku z wirującą tarczą. Zaobserwowano wzrost odporności kawitacyjnej napoin, w których dokonano przetopienia ich powierzchni promieniowaniem lasera.
-
Relationship between cavitation resistance of laser produced alloys and their ability to work hardening
PublicationBadano odporność kawitacyjną laserowo wytworzonych stopów na stalach konstrukcyjnych i ich związek ze zdolnością do umacniania się pod wpływem działania obciążeń kawitacyjnych. Wykazano, że mikrotwardość powierzchni wykazuje monotoniczną zależność z odpornością kawitacyjną i zdolnością do umacniania.
-
Morphology and corrosion characteristics of laser surface remelted Al-Sialloy at cryogenic conditions
PublicationPrzedstawiono koncepcję obróbki laserowej stopu Al-Si w warunkach kriogenicznych. Określono jej wpływ na lokalny skład chemiczny oraz mikrostrukturę i właściwości korozyjne wymienionego stopu. Stwierdzono znaczącą poprawę właściwości korozyjnych w 0,01 M H2SO4.
-
Microstructure and mechanical properties of laser surface-treated Ti13nb13zr alloy with MWCNTs coatings
PublicationLaser surface modification of titanium alloys is one of the main methods of improving the properties of titanium alloys used in implantology. This study investigates the microstructural morphology of a laser-modified surface layer on a Ti13Nb13Zr alloy with and without a carbon nanotube coating deposited by electrophoretic deposition. Laser modification was performed for samples with and without carbon nanotube coating for two...
-
Influence of Laser Modification on the Surface Character of Biomaterials: Titanium and Its Alloys—A Review
PublicationLaser surface modification is a widely available and simple technique that can be applied to different types of materials. It has been shown that by using a laser heat source, reproducible surfaces can be obtained, which is particularly important when developing materials for medical applications. The laser modification of titanium and its alloys is advantageous due to the possibility of controlling selected parameters and properties...
-
Advancements in the Additive Manufacturing of Magnesium and Aluminum Alloys through Laser-Based Approach
PublicationComplex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives such as reduced part numbers, greater functionality, and lightweight, among others. Polymers, metals, and ceramics are the few materials that can be used in AM technology, but metallic materials (Magnesium and Aluminum) are attracting more attention from the research and industrial point of view. Understanding the role...
-
Impact of laser beam welding on mechanical behaviour of 2.25Cr–1Mo (P22) steel
PublicationThe use of welding processes in the manufacturing and repair of structures intended for the energy industry plays a key role in the guarantee of a continuous supply of fossil fuels, which is the basic condition for ensuring energy security. A square butt joint of 10 mm thick plate of 2.25Cr–1Mo (P22) steel was fabricated by autogenous laser beam welding process and then post-weld heat treatment (PWHT) for two sets of process parameters...
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublicationUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
Effects of preheating on laser beam–welded NSSC 2120 lean duplex steel
PublicationDuplex stainless steels show sustainable alternative for the conventional austenitic grades, with higher strength, higher resistance against stress corrosion cracking, and lower purchase cost. Thus, duplex stainless steel gains more attention in construction, oil and gas, and chemical industries. Among duplex stainless steels, low nickel and low molybdenum alloyed lean duplex stainless steel are a cost-efective substitution of...
-
Prosthetic Elements Made of the Ti-13Zr-13Nb Alloy by Selective Laser Melting
PublicationThe fabrication of the prosthetic foundations and bridges from the Ti-13Zr-13Nb alloy is described. The process was started from CAD/CAM design of 3D models of the foundations based on scanning of patient`s mouth. Next, 3D models were transformed into *.stl files for the manufacturing stage and then the manufacturing process by means of the selective laser melting with the SLM Realizer 100 equipment was made. The intrinsic structure...
-
Effect of Laser Treatment on Intrinsic Mechanical Stresses in Titanium and Some of Its Alloys
PublicationLaser surface treatment conducted at different power levels is an option to modify titanium bone implants to produce nano- and microtopography. However, such processing can lead to excess mechanical stress within the surface layer. This research aims to calculate the level of such residual stresses after the surface processing of Ti grade IV, Ti15Mo, and Ti6Al7Nb alloys with an Nd:YAG laser. Light and scanning electron microscopies...
-
Characteristics of La0.8Sr0.2Ga0.8Mg0.2O3-delta -supported micro-tubular solid oxide fuel cells with bi-layer and tri-layer electrolytes
PublicationIn this study, La0.8Sr0.2Ga0.8Mg0.2O3−δ (LSGM)-supported micro tubular solid oxide fuel cells (T-SOFCs) with two different configurations, one containing an LSGM–Ce0.6La0.4O2−δ (LDC) bi-layer electrolyte (Cell A) and one containing an LDC–LSGM–LDC tri-layer electrolyte (Cell B), were fabricated using extrusion and dip-coating. After optimizing the paste formulation for extrusion, the flexural strength of the dense and uniform LSGM...
-
Synthesis of three layer NaxCoO2 (x=0.3, 0.5, 0.6, 0.75, 1.0) and superconductivity in three layer Na0.3CoO2 * 1.3H2O
PublicationDyskutowana jest synteza trójwarstwowego związku sodowo-kobaltowego tlenku NaxCoO2. Związek o zawartości sodu x=0.3 może zostać uwodniony i staje się nadprzewodnikiem z Tc=4.3K. Powierzchnia 3 warstwowego związku charakteryzuje się trójkątną morfologią, podczas gdy dwuwarstwowy związek Na0.7CoO2 - heksagonalną morfologią.
-
The Evaluation of Surface Integrity During Machining of Inconel 718 with Various Laser Assistance Strategies
Publication -
Effect of Na doping on photoluminescence and laser stimulated nonlinear optical features of ZnO nanostructures
Publication -
Technology of laser deposition of narrow bead overlays using solid and flux-cored wires
Publication -
The impact of laser surface treatment on the microstructure, wear resistance and hardness of the AlMg5 aluminum alloy
Publication -
Three Point Bending of Laser Engineered Net Shaping (LENS) Repaired Inconel 625
Publication -
Laser scanning as a source of information in the analysis of the facades of heritage at risk – the mansion in Kliczewo Male
Publication -
Influence of cavitation intensity on the relative cavitation resistance of laser processed C45 carbon steel
PublicationPraca przedstawia badania względnej odporności kawitacyjnej we wstępnym okresie niszczenia laserowo przetopionej 6 kW laserem CO2 stali C45. Badania odporności kawitacyjnej wykonano na stanowisku z wirującą tarczą. Na erodowanej przetopionej warstwie powierzchniowej określono trzy obszary o różnej intensywności oddziaływania obciążeń kawitacyjnych. Określano wielkość odkształceń plastycznych w analizowanych obszarach, spowodowanych...
-
Tailoring of Magnetic Properties of NiO/Ni Composite Particles Fabricated by Pulsed Laser Irradiation
Publication -
Laser-assisted approach for improved performance of Au-Ti based glucose sensing electrodes
PublicationThis paper focuses on the synthesis route and electrochemical properties of electrocatalytic material based on gold nanoparticles (NPs) embedded in a structured titanium template obtained via optimized anodization, chemical etching and laser processing. SEM inspection reveals the presence of Au NPs (60–90 nm in diameter) sited in the titanium foil cavities. Performed electrochemical measurements enable nomination of the set of working...
-
Nanoindentation tests titanium alloy Ti-6Al-4V after interference laser treatment
PublicationThe study aimed was to assess selected mechanical properties of surface layers obtained after interference laser treatment – DLIL of titanium alloy Ti-6Al-4V used for implants. The samples were melted in still air at room temperature, for this purpose Nd:YAG laser was used, the number of laser shots was variable. Next, nanoindentation tests were performed, based on which Young’s modulus and nanohardness in the obtained surface...
-
Laser Beam as a Precision Tool to Increase Fatigue Resistance in an Eyelet of Undercarriage Drag Strut
PublicationThe article contains the results of tests on a laser-processed eyelet of undercarriage drag strut to increase its fatigue strength. Laser processing concentrated on both sides around the hole of eye for connecting the undercarriage drag strut caused that the material in this area withstood more than twice the number of load cycles established for this material. In order to determine the reasons for the increase in fatigue strength,...
-
Model of optical phantoms thermal response upon irradiation with 975 nm dermatological laser
PublicationWe have developed a numerical model describing the optical and thermal behavior of optical tissue phantoms upon laser irradiation. According to our previous studies, the phantoms can be used as substitute of real skin from the optical, as well as thermal point of view. However, the thermal parameters are not entirely similar to those of real tissues thus there is a need to develop mathematical model, describing the thermal and...
-
Influence of Filler Metal on Electrochemical Characteristics of a Laser-Welded CoCrMoW Alloy Used in Prosthodontics
Publication -
Thresholding Methods for Reduction in Data Processing Errors in the Laser-Textured Surface Topography Measurements
Publication -
On the Formation of Single-Walled Carbon Nanotubes in Pulsed-Laser-Assisted Chemical Vapor Deposition
Publication -
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublicationThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
High performance filtering for big datasets from Airborne Laser Scanning with CUDA technology
PublicationThere are many studies on the problems of processing big datasets provided by Airborne Laser Scanning (ALS). The processing of point clouds is often executed in stages or on the fragments of the measurement set. Therefore, solutions that enable the processing of the entire cloud at the same time in a simple, fast, efficient way are the subject of many researches. In this paper, authors propose to use General-Purpose computation...
-
Autogenous Fiber Laser Welding of 316L Austenitic and 2304 Lean Duplex Stainless Steels
PublicationThis study presents results of experimental tests on quality of dissimilar welded joints between 316L austenitic and 2304 lean duplex stainless steels, welded without ceramic backing. Fiber laser welded butt joints at a thickness of 8 mm were subjected to non‐destructive testing (visual and penetrant), destructive testing (static tensile test, bending test, and microhardness measurements) and structure observations (macro‐ and...
-
Use of optical skin phantoms for preclinical evaluation of laser efficiency for skin lesion therapy
PublicationSkin lesions are commonly treated using laser heating. However, the introduction of new devices into clinical practice requires evaluation of their performance. This study presents the application of optical phantoms for assessment of a newly developed 975-nm pulsed diode laser system for dermatological purposes. Such phantoms closely mimic the absorption and scattering of real human skin (although not precisely in relation to...
-
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry
PublicationThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
High resolution optical time-domain reflectometry using sub-picosecond laser sources
PublicationPrzedstawiono działanie sensorów światłowodowych wykorzystujących reflektometrię optyczną w dziedzinie czasu. Omówiono ograniczenia możliwości pomiarowych tej klasy sensorów wynikające z zastosowania w nich reflektometrów światłowodowych zaprojektowanych do zastosowań w telekomunikacji. Zaprezentowano sensory wykorzystujące specjalizowane reflektometry o dużej rozdzielczości. Przedstawiono koncepcję sensora wykorzystującego dwa...
-
Comparison of strain results at a laser weld notch obtained by numerical calculations and experimental measurements
PublicationIn the development of ship structures applying new materials and it’s purposeful placement play an important role. During the last years, especially in a construction of ro-ro type vessels, the usage of novel sandwich structures in cargo decks is profitable. Steel sandwich panel is an innovative solution which at a todays state of development can be used for the construction of any members not taking part in a global bending of...
-
Organic semiconductor rubrene thin films deposited by pulsed laser evaporation of solidified solutions
PublicationOrganic semiconductor rubrene (C42H28) belongs to most preferred spintronic materials because of the high charge carrier mobility up to 40 cm2(V·s)-1. However, the fabrication of a defect-free, polycrystalline rubrene for spintronic applications represents a difficult task. We report preparation and properties of rubrene thin films deposited by pulsed laser evaporation of solidified solutions. Samples of rubrene dissolved in aromatic...
-
Influence of Surface Laser Treatment on Mechanical Properties and Residual Stresses of Titanium and its Alloys
PublicationSurface modification of the titanium and its alloys used in implantology with a long-pulse laser can change the surface topography, but it also leads to changes in the stress sign and magnitude in the resulting subsurface layer. The presented research was aimed at evaluating the state of stress after laser remelting with the Nd:YAG laser of pre-etched titanium alloys Ti6Al4V and Ti13Nb13Zr and pure titanium. The obtained surface...
-
Optimization of the femtosecond laser impulse for excitation and the Spin-Orbit mediated dissociation in the NaRb Dimer
PublicationWe study the dynamics of multiple coupled states under the influence of an arbitrary time-dependent external field to investigate the femtosecond laser-driven excitation and the spin-orbit mediated dissociation in the NaRb dimer. In this process, the dimer is excited from the ground triplet state 1^3Sigma+ to the 1^3Pi state using the femtosecond laser impulse and the spin-orbit coupling between the 1^3Pi and 2^1Sigma+ states results...
-
Nitride LEDs and Lasers with Buried Tunnel Junctions
Publication -
Thin layer chromatography in drug discovery process
Publication -
Noise in electrical double-layer capacitors (EDLCs)
PublicationWe present methods and problems of noise measurements in electrical double-layer capacitors (EDLC). Detailed noise equivalent electronic circuit is considered, and two possible ways of observations of random processes generated in the EDLCs structures are studied. We conclude that noise is a useful tool for characterization of the EDLC structures and their state-of-health, as in other materials and electronic devices. Eventual,...
-
Ceramic composites for single-layer fuel cells
PublicationComposite materials consisting of acceptor doped lanthanum orthoniobate electrolyte phase (La0.98Ca0.02NbO4) and Li2O:NiO:ZnO semiconducting phase were synthesized. The precursor powder of La0.98Ca0.02NbO4 was prepared in nanocrystalline (mechanosynthesis) and microcrystalline (solid-state synthesis) form. The composite can be applied in a single-layer fuel cell, because of the presence of two phases acting as an anode and a cathode...
-
Affective Learning Manifesto – 10 Years Later
PublicationIn 2004 a group of affective computing researchers proclaimed a manifesto of affective learning that outlined the prospects and white spots of research at that time. Ten years passed by and affective computing developed many methods and tools for tracking human emotional states as well as models for affective systems construction. There are multiple examples of affective methods applications in Intelligent Tutoring Systems (ITS)....
-
electrocatalytic sensor based on nasicon with auxiliary layer
PublicationW pracy przedstawiono wyniki badań czujników elektrokatalitycznych z dodatkową warstwą. Właściwości takiego czujnika porównano z czujnikiem o tradycyjnej budowie.
-
Detection of delamination in multi layer composite beams.
PublicationW pracy przedstawiono model belki kompozytowej z delaminacją. Omówiono czynniki propagacji fali sprężystej w belce i możliwości wykorzystania zmian w propagującej fali wywołanych delaminacją do jej detekcji.
-
Diamond-based protective layer for optical biosensors
PublicationOptical biosensors have become a powerful alternative to the conventional ways of measurement owing to their great properties, such as high sensitivity, high dynamic range, cost effectiveness and small size. Choice of an optical biosensor's materials is an important factor and impacts the quality of the obtained spectra. Examined biological objects are placed on a cover layer which may react with samples in a chemical, biological...