Filters
total: 1044
filtered: 874
-
Catalog
Chosen catalog filters
Search results for: NANO-CLAY
-
Fracture of aluminium joints bonded with epoxy adhesive reinforced by mmt nanoparticles
PublicationCrack propagation behavior was studied for aluminium/aluminum adhesive joints bonded with two epoxy adhesives: pure and reinforced with clay nanoparticles. The focus was also on the novel use of the constant displacement rate test to study adhesion/adhesives efficiency. The epoxy systems studied were: Epidian E6 produced from bisphenol A and epichlorohydrin, (''Organika -Sarzyna'' Poland); pure or strengthened with montmorillonit...
-
Microstructure, mechanical properties, and flame retardancy of nanoclay-incorporated polyurethane flexible foam composites
PublicationThe present work seeks to investigate microstructure, mechanical properties, and flame retardancy of polyurethane/nanoclay flexible foam composites. In this regard, we prepared various nanocomposites with and without nanoclay and observed the resulting morphologies to correlate them with the other corresponding characteristics. The results provided support for the fact that tensile strength and compression set will increase with...
-
Platforma KASKADA - proces wytwarzania oprogramowania
PublicationZostał przedstawiony proces wytworzenia Platformy KASKADA służącej do przetwarzania strumieni multimedialnych w rozproszonym środowisku superkom-putera. Przedstawiono wymagania dotyczące Platformy, a następnie opisano przyjętą metodykę wytwarzania. Opi-sano przebieg poszczególnych iteracji procesu. Przedsta-wiono proces wytwarzania usług, od implementacji algo-rytmu, przez wdrożenie na Platformę, aż po akceptację i udostępnienie...
-
A Review of Recent Advances in Human-Motion Energy Harvesting Nanogenerators, Self-Powering Smart Sensors and Self-Charging Electronics
PublicationIn recent years, portable and wearable personal electronic devices have rapidly developed with increasing mass production and rising energy consumption, creating an energy crisis. Using batteries and supercapacitors with limited lifespans and environmental hazards drives the need to find new, environmentally friendly, and renewable sources. One idea is to harness the energy of human motion and convert it into electrical energy...
-
A novel hierarchically-porous diamondized polyacrylonitrile sponge-like electrodes for acetaminophen electrochemical detection
PublicationA novel composite electrode material consisting of tangled fibrous polyacrylonitrile-based hierarchically-struc- tured nanocomposites has been produced by wet-spinning, carbonized and decorated with a carbon nano- architecture by microwave plasma-enhanced chemical vapor deposition and investigated as a metal-free electrode for the enhanced electrochemical detection of acetaminophen. Surprisingly, the hierarchical fiber ar- chitecture...
-
Properties of ordered titanium templates covered with Au thin films for SERS applications
PublicationtCurrently, roughened metal nanostructures are widely studied as highly sensitive Raman scattering sub-strates that show application potential in biochemistry, food safety or medical diagnostic. In this workthe structural properties and the enhancement effect due to surface enhanced Raman scattering (SERS) ofhighly ordered nano-patterned titanium templates covered with thin (5–20 nm) gold films are reported.The templates are formed...
-
Synthesis and structural properties of (Y, Sr)(Ti, Fe, Nb)O3−δ perovskite nanoparticles fabricated by modified polymer precursor method
PublicationThe yttrium, iron and niobium doped-SrTiO3 powders have been successfully fabricated by a modified low–temperature synthesis method from a polymer complex. The usage of strontium hydroxide precursor instead of conventional strontium nitrate or strontium carbonate provides to the possibility of significant decrease of annealing temperature. It allows to prepare a material with sphere-shape grains of nanometric size (15–70 nm). The...
-
Mask Detection and Classification in Thermal Face Images
PublicationFace masks are recommended to reduce the transmission of many viruses, especially SARS-CoV-2. Therefore, the automatic detection of whether there is a mask on the face, what type of mask is worn, and how it is worn is an important research topic. In this work, the use of thermal imaging was considered to analyze the possibility of detecting (localizing) a mask on the face, as well as to check whether it is possible to classify...
-
Threats to Armenia’s Security in the National Strategy and Practice with Special Emphasis on External Security,
PublicationThe national security strategy adopted in 2007 provided a detailed definition of security and identified its threats. The key threat to the Armenian state was considered to be the Nagorno-Karabakh conflict. The document indicated the Collective Security Treaty Organisation main guarantor of security, with Russia being Armenia’s main partner in bilateral relations. The second position in the strategy was assigned to cooperation...
-
Some aspects of the constitutive modelling of natural fine grained soils
PublicationThe monograph deals with selected problems of the constitutive modelling of natural fine grained soils commonly known as clays. The main idea is not to propose a unified model which is capable of describing all known features of mechanical behaviour of fine grained soils. Instead, separate models are proposed describing the mechanical behaviour of heavily overconsolidated, lightly overconsolidated and normally consolidated clays....
-
AUTOMATIC LEARNING OF STRATEGY AND RULES IN CARD GAMES USING IMAGE FROM CAMERA
PublicationBelow work tries to answer a question: if it is possible to replace real human with computer system in social games. As a subject for experiments, card games were chosen, because they require a lot of player interaction (playing and taking cards), while their rules are easy to present in form of clear list of statements. Such a system, should allow real players to play without constant worrying about guiding or helping computer...
-
Zmiana szybkości próbkowania z użyciem filtrów ułamkowoopóźniających projektowanych oknem offsetowanym z pomocą aproksymacji wielomianowej
PublicationW pracy przedstawiono problem realizacji algorytmu zmiany szybkości próbkowania z użyciem filtrów ułamkowoopóźniających. Zaproponowano tutaj zastąpić filtry optymalne, filtrami projektowanych metodą okien offsetowanych. Uzyskujemy w ten sposób rozwiązanie pozbawione silnych listki występujące w paśmie zaporowym filtru zbiorczego jednak pojawia się problem realizacji offsetowania okna prototypowego, które zapropono-wano realizować...
-
Removal and retention of selected heavy metals in components of a hybrid wetland system
PublicationProwadzone badania z określeniem możliwosci retencjonowania metali ciężkichw systemie hybrydowej oczyszczalni hydrofitowej. Wykazano, że znaczna rete- ncja tych pierwiastków następowała w wyniku sorpcji. Przeprowadzona ekstra- kcyjna analiza sekwencyjna wykazała, że Pb2+ i Cu2+ zostały zakumulowane w połączeniach trwałych i nie powinny ulegać wymywaniu z oczyszczalni. Nato- miast Cd2+ wskutek sorpcji we frakcjach labilnych może...
-
Modeling of the L and M x-ray line structures for tungsten in high-temperature tokamak plasmas
Publication -
A review on the critical challenges and progress of SiOx-based anodes for lithium-ion batteries
Publication -
Upcycle waste plastics to magnetic carbon materials for dye adsorption from polluted water
Publication -
Sporothrix schenckii: purification and partial biochemical characterisation of glucosamine-6-phosphate synthase, a potential antifungal target
PublicationW artykule opisano izolację i charakterystykę właściwości natywnego enzymu, syntazy GlcN-6-P z komórek dimorficznego grzyba patogennego Sporothrix schenckii. Masę cząsteczkową enzymu natywnego określono na 350 kDa, a enzymu zdenaturowanego na około 79 kDa, co sugeruje homotetrameryczną strukturę białka. Wartość punktu izoelektrycznego wyniosła 6,26; wyznaczono także parametry kinetyczne katalizowanej reakcji. Aktywność enzymu była...
-
Influence of Installation Effects on Pile Bearing Capacity in Cohesive Soils – Large Deformation Analysis Via Finite Element Method
PublicationIn this paper, the whole process of pile construction and performance during loading is modelled via large deformation finite element methods such as Coupled Eulerian Lagrangian (CEL) and Updated Lagrangian (UL). Numerical study consists of installation process, consolidation phase and following pile static load test (SLT). The Poznań site is chosen as the reference location for the numerical analysis, where series of pile SLTs...
-
Mechanism of Li nucleation at graphite anodes and mitigation strategies
PublicationLithium metal plating is a critical safety issue in Li-ion cells with graphite anodes, and contributes significantly to ageing, drastically limiting the lifetime and inducing capacity loss. Nonetheless, the nucleation mechanism of metallic Li on graphite anodes is still poorly understood. But in-depth understanding is needed to rationally design mitigation measures. In this work, we conducted FirstPrinciples studies to elucidate...
-
Stone cutting industry waste-supported zinc oxide nanostructures for ultrasonic assisted decomposition of an anti-inflammatory non-steroidal pharmaceutical compound
PublicationPowdered stone waste (PSW) obtained from a stone cutting industrial unit was applied as support for the immobilization of nano-sized ZnO to be utilized as an effective catalyst for the catalytic conversion of acetaminophen (ACE) under ultrasonication. The incorporation of ZnO nanostructures into PSW structure enhanced the specific surface area and pore volume of the as-prepared nanocompound. The change in the value of zero point...
-
Plasma-Based Deposition and Processing Techniques for Optical Fiber Sensing
PublicationPlasma-based techniques are widely applied for well-controlled deposition, etching or surface functionalization of a number of materials. It is difficult to imagine fabrication of novel microelectronic and optoelectronic devices without using plasma-enhanced deposition of thin films, their selective etching or functionalization of their surfaces for subsequent selective binding of chemical or biological molecules. Depending on...
-
Magnetic nanocomposites for biomedical applications
PublicationTissue engineering and regenerative medicine have solved numerous problems related to the repair and regeneration of damaged organs and tissues arising from aging, illnesses, and injuries. Nanotechnology has further aided tissue regeneration science and has provided outstanding opportunities to help disease diagnosis as well as treat damaged tissues. Based on the most recent findings, magnetic nanostructures (MNSs), in particular,...
-
Analysis of pounding between adjacent buildings founded on different soil types
PublicationEarthquake-induced pounding was experienced in many previous earthquakes and it was found to be a critical issue. This study investigates the effect of pounding between buildings founded on the same and different soil types. Three 3-D buildings with 4, 6 and 8 storeys were considered in this study. Three pounding scenarios were taken into account, i.e. pounding between 4-storey and 6-storey buildings, between 4-storey and 8-storey...
-
THE USE OF MORPHOLOGICAL FILTERS AND GRANULOMETRIC METHOD TO ANALYZE THE MOVEMENT OF THE MOLECULES IN THE SEA WATER OF THE SOUTHERN BALTIC SEA
PublicationModern granulometry opens a new way of analysing images by means of morphological filters. In this paper a closer look has been presented on the problem of interpreting information about the features and conditions of marine environment from images taken at the sea coast and shallow water. Using this method allows for example selection of the objects on the image according to the differences in shape. Processes occurring in the...
-
Smart Virtual Product Development (SVPD) to Enhance Product Manufacturing in Industry 4.0
PublicationThis paper presents a system capable of enhancing product development process for industrial manufactured products. This system is known as Smart Virtual Product Development (SVPD), and it helps in decision making by using explicit knowledge of formal decision events. It stores and reuses the past decisional events or sets of experiences related to different activities involved in industrial product development process i.e. product...
-
Problemy techniczne w wyłącznikach selektywnych
PublicationArtykuł przedstawia problemy techniczne z wyłącznikami selektywnymi typu S90 które obserwo-wano w czasie załączania obwodów grzewczych zasilanych poprzez transformatory separacyjne przy obciążeniach niższych od znamionowych. Wielokrotnie rejestrowano występujące po załączeniu se-kwencje prądów przeciążających układ zestykowy wyłącznika powodujące jego uszkodzenie w dłuższym horyzoncie czasowym. W badanym wyłączniku selektywnym...
-
Chłodzenie materii poprzez fluorescencję antystokesowską
Publicationnane są różne metody chłodzenia wykorzystujące procesy termodynamiczne, zjawiska termoelektryczne i magnetoelektryczne. W artykule przedstawiono możliwości chłodzenia materii poprzez fluorescencję antystokesowską materiału luminezującego oświetlanego światłem laserowym o określonej długości fali. Materiałami szczególnie korzystnymi są szkła domieszkowane metalami ziem rzadkich n.p. szkło typu ZBLAN, zawierające iterb. Układy takie...
-
Application of acoustic emission metod for measurement of joint gap and cartilage surfaces
PublicationW artykule przedstawiono zastosowanie emisji akustycznej do lokalizacji wczesnych uszkodzeń stawu biodrowego lub kolanowego człowieka. Ponadto metoda ta służy do pomiaru wysokości szczeliny stawu oraz struktury geometrycznej powierzchni chrząstki stawowej. Jest to metoda nieinwazyjna. Pomiary metodą emisji akustycznej stosujemy na ogół w materiałach, w których energia sprężysta zmienia się nagle. Takie zmiany energii mogą być...
-
Composite 2D Material-Based Pervaporation Membranes for Liquid Separation: A Review
PublicationToday, chemistry and nanotechnology cover molecular separations in liquid and gas states by aiding in the design of new nano-sized materials. In this regard, the synthesis and application of two-dimensional (2D) nanomaterials are current fields of research in which structurally defined 2D materials are being used in membrane separation either in self-standing membranes or composites with polymer phases. For instance, pervaporation...
-
Metal–Organic Frameworks (MOFs) for Cancer Therapy
PublicationMOFs exhibit inherent extraordinary features for diverse applications ranging from catalysis, storage, and optics to chemosensory and biomedical science and technology. Several procedures including solvothermal, hydrothermal, mechanochemical, electrochemical, and ultrasound techniques have been used to synthesize MOFs with tailored features. A continued attempt has also been directed towards functionalizing MOFs via “post-synthetic...
-
Design and Microwave-Assisted Synthesis of TiO2-Lanthanides Systems and Evaluation of Photocatalytic Activity under UV-LED Light Irradiation
PublicationThe TiO2-Eu and TiO2-La systems were successfully synthesized using the microwave method. Based on the results of X-ray diffraction analysis, it was found that regardless of the analyzed systems, two crystal structures were noted for the obtained samples: anatase and rutile. The analysis, such as XPS and EDS, proved that the doped lanthanum and europium nano-particles are present only on the TiO2 surface without disturbing the...
-
Ladder-Based Synthesis and Design of Low-Frequency Buffer-Based CMOS Filters
PublicationBuffer-based CMOS filters are maximally simplified circuits containing as few transistors as possible. Their applications, among others, include nano to micro watt biomedical sensors that process physiological signals of frequencies from 0.01 Hz to about 3 kHz. The order of a buffer-based filter is not greater than two. Hence, to obtain higher-order filters, a cascade of second-order filters is constructed. In this paper, a more...
-
Simultaneous removal of heavy metals and dyes in water using a MgO-coated Fe3O4 nanocomposite: Role of micro-mixing effect induced by bubble generation
PublicationThis study focused on the development of a nano-adsorbent for contaminant removal without the use of any external energy. An eco-friendly Fe3O4@MgO core-shell nanocomposite was synthesized and tested for the removal of a heavy metal, lead (Pb2+) and a dye, rhodamine B (RhB). The addition of H2O2 into the system enabled the self-mixing of the aqueous solution containing Fe3O4@MgO through the generation of bubbles. This system showed...
-
Role of size scale of ZnO nanoparticles and microparticles on toxicity toward bacteria and osteoblast cancer cells
PublicationThe specific role of size scale, surface capping, and aspect ratio of zinc oxide (ZnO) particles on toxicity toward prokaryotic and eukaryotic cells was investigated. ZnO nano and microparticles of controlled size and mor- phology were synthesized by wet chemical methods. Cytotoxicity toward mammalian cells was studied using a human osteoblast cancer cell line and antibacterial activity using Gram-negative bacteria (Escherichia...
-
Biopolymer-based composites for tissue engineering applications: A basis for future opportunities
PublicationBiomimetic scaffolds supporting tissue regeneration are complex materials with multifunctional characteristics. The unique biocompatibility and biodegradability of biopolymers make them excellent candidates for tissue engineering and regenerative medicine. Biopolymers, which have a wide range of properties, can be obtained from different natural sources. Depending on the target tissue, biopolymers can be engineered to meet a series...
-
Reinforcing and plasticizing effects of reclaimed rubber on the vulcanization and properties of natural rubber
PublicationThe production of high-added value reclaimed rubber (RR) is of great signifi-cance for the sustainability of rubber industries. To green recycle waste rub-bers and broaden the application of RR, a RR material with potentialreinforcing and plasticizing effects on nature rubber (NR) composites are pre-pared by a thermo-oxidative reclamation process. The reclamation degree ofRR is controlled by adjusting the content of soybean oil....
-
IoT for healthcare applications
PublicationThis chapter summarizes IRACON contributions related to the application of IoT in healthcare. It consists of the following three sections. Section 8.1 presents the measurement campaigns and the related statistical analysis to obtain various channel models for wearable and implantable devices. In addition, the importance of physical human-body phantoms used for channel, Specific Absorption Rate (SAR), and Electromagnetic (EM) exposure...
-
Morphology of damage inflicted on brittle polymer in lubricated contact under cyclic static load
PublicationIn this article morphology of damage inflicted on the polymethylmethacrylate (PMMA) plate in static point lubricated contact with a ball made of five different materials under cyclic normal load has been presented. It is argued that the counterface material and lubricating film play an important role in the damage process and the extent of damage inflicted in the PMMA plate.
-
Long-Term Impact of Wind Erosion on the Particle Size Distribution of Soils in the Eastern Part of the European Union
PublicationWind erosion is the leading cause of soil degradation and air pollution in many regionsof the world. As wind erosion is controlled by climatic factors, research on this phenomenon isurgently needed in soil and land management in order to better adapt to climate change. In thispaper, the impact of wind erosion on the soil surface in relation to particle size distribution wasinvestigated. Changes in percentage of sand, silt and...
-
CENTRAL-FORCE DECOMPOSITION OF THE TERSOFF POTENTIAL
PublicationCentral forces play important role in the analysis of results obtained with particle simulation methods, since they allow evaluating stress fields. In this work we derive expressions for a central-force decompositon of the Tersoff potential, which is often used to describe interatomic interactions in covalently bonded materials. We simplify the obtained expressions and discuss their properties.
-
Large deformation modelling of CPT probing in soft soil—pore water pressure analysis
PublicationThis paper presents the results of finite element modelling with Updated Lagrangian formulation of the Cone Penetration Test in soft soil deposit located in Jazowa, Poland. The numerical calculations are carried out for homogenous, normally consolidated, organic soil layer. The Modified Cam Clay constitutive model for soft soil and Coulomb model for interface are used. The study compares the registered pore water pressure distributions...
-
Selection of material for X-ray tomography analysis and DEM simulations: comparison between granular materials of biological and non-biological origins
PublicationPhysical properties and X-ray tomography images of five different granular materials: glass bead, glass grit, short grain white rice, sorghum and clay granules (Seramis) are investigated to select the most promising materials for numerical simulations and time-lapse X-ray tomography imaging. The examined materials represent granular materials of non-biological origin (glass bead, glass grit and Seramis) and granular plant materials...
-
Experimental study on steel columns subjected to impact load under earthquake conditions
PublicationEarthquakes affecting urbanized regions cause exceptional loads to load bearing structural elements such as columns. Such a boost in the load conditions can lead to severe damages which, in a worst case scenario, can lead to a total collapse of a building. This boost is caused by the horizontal ground movement generating a rise in the internal forces due to considerable large displacement between the top and bottom support of columns....
-
Database systems for tomorrow: new challenges and research areas
PublicationZaprezentowano nowe obszary badawcze w dziedzinie baz danych, które będą rozwijane w najbliższej przyszłości. Omówiono takie obszary jak systemy typu ''Plug and Play'', duże systemy sfederowane, nowe architektury systemów baz danych oparte na dużych buforach pamięciowych, integracja danych i aplikacji oraz bazy danych semistrukturalnych.
-
Nonlinearity shaping in nanostructured glass-diamond hybrid materials for optical fiber preforms
PublicationNanodiamond integration with optical fibers has proved a compelling methodology for magneto-optics. We reveal that the applicability of nanodiamonds in nonlinear optics goes beyond the previous demonstrations of frequency converters. Instead, we exploit the recently reported volumetric integration of nanodiamonds along the optical fiber core and show that the nonlinear response of glasses can be manipulated by nanodiamonds. By...
-
Characteristics of silver-dopped carbon nanotube coating destined for medical applications
PublicationCarbon nanotubes are materials demonstrating outstanding mechanical, chemical, and physical properties and are considered coatings of titanium implants. The present research is aimed to characterize the microstructure and properties of the multi-wall carbon nanotubes (MWCNTs) layer decorated with silver nanoparticles (Ag NPs) on the Ti13Nb13Zr alloy destined for long-term implants. The electrophoretic deposition of coatings...
-
Combination of air-dispersion cathode with sacrificial iron anode generating Fe2+Fe3+2O4 nanostructures to degrade paracetamol under ultrasonic irradiation
PublicationIn the present study, ultrasound (US) was coupled with an electrochemical process (ECP) consisting of a novel cathode of carbon cloth (CC)-carbon black (CB) as the nano-composite air-dispersion cathode (NADC) for the degradation of paracetamol (APAP) in an aquatic medium. The NADC favored in situ production of H2O2 by the cathodic reduction. The implementation of iron sacrificial anode instead of dimensionally stable anodes resulted...
-
Assembly of 1D Granular Structures from Sulfonated Polystyrene Microparticles
PublicationBeing able to systematically modify the electric properties of nano- and microparticles opens up new possibilities for the bottom-up fabrication of advanced materials such as the fabrication of one-dimensional (1D) colloidal and granular materials. Fabricating 1D structures from individual particles offers plenty of applications ranging from electronic sensors and photovoltaics to artificial flagella for hydrodynamic propulsion....
-
Synergistic effect of fumed silica with Ni2O3 on improving flame retardancy of poly(lactic acid)
Publication -
Unusual streaming in chemically reacting gases
PublicationNonlinear stimulation of the vorticity mode caused by losses in the momentum of sound in the chemically reacting gas, is considered. The instantaneous dynamic equation which describes the nonlinear generation of the vorticity mode, is derived. It includes a quadratic nonlinear acoustic source. Both periodic and aperiodic sound may be considered as the origin of the vorticity flow. In the non-equilibrium regime of the chemical reaction,...