Filters
total: 1393
displaying 1000 best results Help
Search results for: SCRAB TIRES
-
The best porous asphalt pavement in Sweden so far
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Surface-Plasmon-Coupled Emission of Rhodamine 110 in a Silica Nanolayer
PublicationThe first observation of strong directional surface-plasmon-coupled emission (SPCE) of Rhodamine 110 in silica nanofilms deposited on silver nanolayers is reported. The preparation of the material is described in detail. The intensity of SPCE exceeds 10 times that of free space fluorescence and total linear light polarization in the SPCE ring is observed. A new experimental setup and an original data collection method is presented....
-
The XRD diffraction patterns of annealed Ce0.9M0.1O2 powders prepared using the reverse microemulsion method
Open Research DataThe dataset includes XRD patterns of Ce0.9M0.1O2 (where M=Mn, Fe, Co, Ni, Cu) nanopowders prepared using the reverse microemulsion method. The powders were precipitated from organic-based solution of nitrates using TMAOH. The sediment was cetrifuged and rinsed with alcohol several times. Powders were dried and calcinated at 500 degrees for 2 h, followed...
-
Influence of controlled crystallization and SrF2 content on the structure and properties of Eu3+ doped phosphate glasses
Open Research DataThe attached data contains the results of measurements of phosphate glasses and glass-ceramics doped with Eu. On their basis, the new material was characterized and the influence of the SrF2 addition on the glass structure was determined. In addition, the influence of the SrF2 content and controlled crystallization on the luminescent properties of Eu3+...
-
Maciej Matciak doktor
People -
Relieving the Measuring System of the Trailer for Tyre/Road Rolling Resistance Measurements from the Inertia Force
PublicationIn the article the principle of measuring of tyre/road rolling resistance tyres in road conditions applied in a special measuring trailer is presented. This trailer was built in Faculty of Mechanical Engineering at Gdansk University of Technology. The construction of two special devices used in this trailer was discussed. These devices eliminate the influence of some chosen confounding measurements factors such as: the inertia...
-
Convergence to equilibrium under a random Hamiltonian
PublicationWe analyze equilibration times of subsystems of a larger system under a random total Hamiltonian, in which the basis of the Hamiltonian is drawn from the Haar measure. We obtain that the time of equilibration is of the order of the inverse of the arithmetic average of the Bohr frequencies. To compute the average over a random basis, we compute the inverse of a matrix of overlaps of operators which permute four systems. We first...
-
Agnieszka Pladzyk dr hab. inż.
PeopleAgnieszka Pladzyk, born in 1973 in Pisz, graduated in 1998 in Biotechnology from the Faculty of Chemistry GUT. Her MSc thesis entitled Production of recombinant human calcitonin in bacterial system and its purification with the use of metal affinity chromatography was done under the supervision of professor Józef Kur. In 2003 she defended the PhD with distinctions and her PhD thesis entitled Cobalt tri-tert-butoxysilanethiolates...
-
ZNACZENIE CZYNNIKA PRACY W DOCHODZIE NARODOWYM
PublicationW większości krajów o rozwiniętej gospodarce rynkowej, udział pracy w dochodzie narodowym stale obniża się. W literaturze światowej wskazuje się różne przyczyny występowania tego zjawiska. Jedną z przy-czyn obserwowanej tendencji są nasilające się procesy globalizacji. Mają one wpływ na poziom dochodów osiąganych z tytułu świadczenia pracy, tym samym wpływają na udział pracy w dochodzie narodowym. Poza tym wśród czynników determinujących...
-
Reduction of noise and rolling resistance by horizontal grinding of asphalt pavements
PublicationGrinding of cement concrete pavements to reduce unevenness and noise is common since a long time. Grinding is then made with wheels equipped with diamond blades rotating in the vertical plane. This creates narrow vertical/longitudinal grooves in the pavement. It is not applied to asphalt pavements. In this paper an alternative type of grinding is studied. In this case plates with diamond heads rotate in the same plane as the pavement,...
-
Synergy between AgInS2 quantum dots and ZnO nanopyramids for photocatalytic hydrogen evolution and phenol degradation
PublicationDespite the unique properties of single semiconductor nanomaterials and quantum dots, poor photocatalytic activity has characterized them and the fabrication of nanocomposites has become necessary to enhance their photocatalytic performance. Thus, AgInS2 quantum dots (AIS QDs, 4.0±1.6 nm), have been successfully prepared and loaded onto ZnO nanopyramids (ZnO NPy). The effect of the nominal amount of AIS QDs decorating ZnO NPy on...
-
A few steps more towards NPT bound entanglement
PublicationIn this paper, existence of bound entangled states with nonpositive partial transpose (NPT) is considered. As one knows, existence of such states would in particular imply nonadditivity of distillable entanglement. Moreover, it would rule out a simple mathematical description of the set of distillable states. The particular state, known to be 1-copy nondistillable and supposed to be bound entangled, is considered. The problem of...
-
Zirconia-based mixed potential sensor with Pt electrode prepared by spin-coating of polymeric precursor
PublicationMany types of yttria-stabilized zirconia (YSZ) based gas sensors have been explored extensively in recent years. Great attention have been directed to mixed-potential-type gas sensors. It is due to growing concerns with environmental issues. Not without a significance is the fact of very attractive performance of this type of sensor allowing to detect low concentration of pollutant gases. In this paper two types of YSZ based mixed-potential...
-
Various types of semiconductor photocatalysts modified by CdTe QDs and Pt NPs for toluene photooxidation in the gas phase under visible light
PublicationA novel synthesis process was used to prepare TiO2 microspheres, TiO2 P-25, SrTiO3 and KTaO3 decorated by CdTe QDs and/or Pt NPs. The effect of semiconductor matrix, presence of CdTe QDs and/or Pt NPs on the semiconductor surface as well as deposition technique of Pt NPs (photodeposition or radiolysis) on the photocatalytic activity were investigated. The as-prepared samples were characterized by X-ray powder diffractometry (XRD),...
-
Study on the Structure-Property Dependences of Rigid PUR-PIR Foams Obtained from Marine Biomass-Based Biopolyol
PublicationThe paper describes the preparation and characterization of rigid polyurethane-polyisocyanurate (PUR-PIR) foams obtained with biopolyol synthesized in the process of liquefaction of biomass from the Baltic Sea. The obtained foams differed in the content of biopolyol in polyol mixture (0–30 wt%) and the isocyanate index (IISO = 200, 250, and 300). The prepared foams were characterized in terms of processing parameters (processing...
-
History of urban planning I
e-Learning CoursesThe course is aimed to the Erasmus students in the summer term. During he course students learn the principles and conditions of development of urban settlements in the time periods from ancient times to the 18th century (ancient Greece, Rome, Middle Ages, Renaissance, Baroque and Classicism). The students prepare 3 excercises: Task 1 - Cities of ancient Greece and Rome; Task 2 - Medieval Cities; Task 3 - Cities of Renaissance,...
-
Reclaimed Rubber/Poly(ε‐caprolactone) Blends: Structure, Mechanical, and Thermal Properties
PublicationThe amount of elastomeric waste, especially from tires is constantly increasing on a global scale. The recycling of these residua should be considered a priority. Compounding the waste rubbers with other polymers can be an excellent alternative to reuse waste materials. This procedure requires solving the issue of the lack of compatibility between the waste rubber particles and other polymers. Simultaneously, there is a claim for...
-
Paweł Filipkowski dr inż.
PeoplePaweł Filipkowski Ph.D. Biotechnology Department of Chemistry, Technology and Biotechnology of Food Faculty of Chemistry Gdansk University of Technology Narutowicza 11/12 80-233 Gdansk, Poland Tel: +48 58 3472456 e-mail: pawel.filipkowskiATpg.edu.pl Current position: Assistant Professor/Senior Lecturer*(from Jan.2019) of Biotechnology, Department of Chemistry, Technology and Biotechnology of Food, Gdansk University of Technology. Education: Eng....
-
Charakterystyka odcieków powstających w aspekcie wyboru metody ich oczyszcania
PublicationArtykuł obejmuje analizę odcieków generowanych w zakładach utylizacji odpadów w aspekcie ich ilości i jakości oraz możliwości oczyszczania/zagospodarowania, ze szczególnym zwróceniem uwagi na metody biologiczne, najbardziej przyjaznej środowisku. Ponad trzyletnie badania prowadzono na dwóch obiektach zlokalizowanych w woj. pomorskim, gdzie pobierano próbki ścieków technologicznych, powstających podczas sortownia oraz kompostownia odpadów...
-
Parallelization of Compute Intensive Applications into Workflows based on Services in BeesyCluster
PublicationThe paper presents an approach for modeling, optimization and execution of workflow applications based on services that incorporates both service selection and partitioning of input data for parallel processing by parallel workflow paths. A compute-intensive workflow application for parallel integration is presented. An impact of the input data partitioning on the scalability is presented. The paper shows a comparison of the theoretical...
-
Implementation of Coprocessor for Integer Multiple Precision Arithmetic on Zynq Ultrascale+ MPSoC
PublicationRecently, we have opened the source code of coprocessor for multiple-precision arithmetic (MPA). In this contribution, the implementation and benchmarking results for this MPA coprocessor are presented on modern Zynq Ultrascale+ multiprocessor system on chip, which combines field-programmable gate array with quad-core ARM Cortex-A53 64-bit central processing unit (CPU). In our benchmark, a single coprocessor can be up to 4.5 times...
-
Remarkable visible-light induced hydrogen generation with ZnIn2S4 microspheres/CuInS2 quantum dots photocatalytic system
PublicationA new and active material in the form of ZnIn2S4 microspheres decorated by CuInS2 quantum dots have been obtained by hydrothermal method for the first time. The optimum amount of CuInS2 quantum dots (1.13 wt.%) introduced into rection medium during ZnIn2S4 microspheres synthesis increased the photocatalytic H2 generation rate by 2.5 times than that of bare ZnIn2S4 photocatalysis under visible light irradiation. This sample exhibited...
-
The influence of esterification time on the physicochemical properties of poly (glycerol sebacate-co- butylene sebacate)
PublicationThe study presents the results of the physicochemical properties of ester elastomer based on sebacic acid, glycerol and 1,4 - butanediol. The process of obtaining elastomers at variable esterification times of 14, 16 and 21 h is described. It was found that the material with an esterification time of 21 h is characterized by the best mechanical properties while maintaining high content of the gel fraction. In the technological...
-
On thermal stability of topological qubit in Kitaev's 4D model
PublicationWe analyse stability of the four-dimensional Kitaev model-a candidate for scalable quantum memory - in finite temperature within the weak coupling Markovian limit. It is shown that, below a critical temperature, certain topological qubit observables X and Z possess relaxation times exponentially long in the size of the system. Their construction involves polynomial in system size algorithm which uses as an input the results of...
-
Sharp transitions in low-number quantum dots Bayesian magnetometry
PublicationWe consider Bayesian estimate of static magnetic field, characterized by a prior Gaussian probability distribution, in systems of a few electron quantum dot spins interacting with infinite temperature spin environment via hyperfine interaction. Sudden transitions among optimal states and measurements are observed. Usefulness of measuring occupation levels is shown for all times of the evolution, together with the role of entanglement...
-
The new version of contact-less method for localisation of catenary contact wire – theoretical assumption
PublicationThis article presents the theoretical basic of a new version of contact-less method for localising the catenary contact wires, using the advanced video techniques and image analysis. So far, contact line diagnostic systems exploited nowadays uses the contact measuring methods with special design current collector. This solutions make it impossible to measure the contact line geometry in a static way. The proposed measurement method...
-
Methane emissions from mangrove soils in hydrologically disturbed and reference mangrove tidal creeks in southwest Florida
PublicationStudies have suggested that some mangrove soils might contribute to wetland methane (CH4) production and emissions, especially when the mangroves are disturbed. CH4 emissions were measured seasonally from nine locations on two mangrove creeks on Naples Bay in southwest Florida, USA. One of the tidal creeks has been impacted in the past few decades with alteration of upstream watersheds and freshwater inflows; the other creek was...
-
Jakość usług w optycznej sieci wielodomenowej z hierarchiczną strukturą płaszczyzn sterowania
PublicationW rozprawie przedstawiono przegląd architektur sieci z gwarancją jakości klas usług oraz stan prac w zakresie realizacji optycznych sieci ASON, GMPLS oraz ASON/GMPLS. Opisano wymagania i zaawansowanie prac w realizacji sieci ASON/GMPLS z hierarchiczną strukturą płaszczyzn sterowania oraz problemy związane z zagadnieniem jakości klas usług w tej sieci. Zaprezentowano założenia, koncepcję oraz realizację modelu symulacyjnego optycznej...
-
Drill holes decrease cancellous bone strength: A comparative study of 33 paired osteoporotic human and 9 paired artificial bone samples
PublicationThis study was designed to compare compressive strength of cancellous bone retrieved from the femoral head in a specimen with and without guide wire hole, with comparison to synthetic bone samples. Femoral heads retrieved from 33 patients who sustained femoral neck fractures and underwent hip arthroplasty were cut into cuboids leaving two matching samples from the same femoral head. Similar samples were prepared from synthetic femurs....
-
Transparent TiO2 nanotubes supporting silver sulfide for photoelectrochemical water splitting
PublicationDifferences between photoelectrochemical and electrochemical activity were thoroughly investigated for the oxygen evolution reaction mediated by Ag2S deposited on two types of ordered titania substrates. Titanium dioxide nanotubes were fabricated by anodization of magnetron sputtered Ti films on ITO-coated glass substrates or directly from Ti foil. Further, Ag2S deposition on the nanotubes was carried out using successive ionic...
-
Hybrid P3HT: PCBM/GaN nanowire/Si cascade heterojunction for photovoltaic application
PublicationPoly(3-hexylthiophene) (P3HT) and phenyl-C61-butyric acid methyl ester (PCBM) are commonly used for the fabrication of organic photovoltaics (OPV). Efficiency limitations of OPVs could be circumvented by incorporation of inorganic nanostructures into organic blends. Again, integration of organic solar cells with well-developed silicon photovoltaic technology is ultimately desirable. In present work, GaN nanowires with diameters...
-
Benchmarking Performance of a Hybrid Intel Xeon/Xeon Phi System for Parallel Computation of Similarity Measures Between Large Vectors
PublicationThe paper deals with parallelization of computing similarity measures between large vectors. Such computations are important components within many applications and consequently are of high importance. Rather than focusing on optimization of the algorithm itself, assuming specific measures, the paper assumes a general scheme for finding similarity measures for all pairs of vectors and investigates optimizations for scalability...
-
Human serum interactions with phenolic and aroma substances of Kaffir(Citrus hystrix) and Key lime (Citrus aurantifolia) juices
PublicationTo understand the therapeutic application of polyphenols extracted from Kaffir (PolKaf) and Key (PolKey) limesdifferent analytical methods were applied. Based on quantitative analysis by two dimensional gas chromato-graphy (GC×GC) and time of flight mass spectrometry (TOFMS) it can be observed that the biggest differencesin the contents of selected terpenes of Kaffir and Key limes occur in chemical compounds such as limonene, citraland...
-
Tyre/road noise reduction by a poroelastic road surface
PublicationLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Analysis of start energy of Stirling engine type alpha
PublicationThe Stirling engine type alpha is composed of two cylinders (expansion space E and compression space C), regenerator that forms the space between the cylinders and the buffer space (under the pistons). Before the start-up and as a result of long-term operation, the average pressure in the working space (above the pistons) and in the buffer space is the same. However, in the initial phase of operation, the average pressure in the...
-
Triplet Formation and Triplet‐Triplet Annihilation Upconversion in Iodine Substituted Non‐Orthogonal BODIPY‐Perylene Dyads
PublicationBODIPY-perylene dyads have emerged as useful metal free sensitizers for triplet-triplet annihilation upconversion (TTAUC), these dyads are capable of efficient triplet generation via spinorbit charge transfer intersystem crossing (SOCT-ISC). This important route to triplet formation requires dyads in which two moieties are oriented perpendicular to each other. In this contribution, we give a deeper insight on the behavior of recently...
-
Exploring the trends in flux-cored arc welding: scientometric analysis approach
PublicationFlux-cored arc welding (FCAW) is a universal group of welding methods in terms of the scope of application and automation possibilities, the share of which in various industries in many countries is still increasing. The paper presents the results of bibliographic analyses (scientometric analysis with the use of VOSviewer, Bibliometrix and CitNetExplorer tools) of a data set of 993 publications indexed in the Web of Science database...
-
The share of employment in individual cities in total employment in the BPO/SSC sector in Poland
Open Research DataEmployment in the sector in 2019 was almost three times higher than in 2013. Throughout the analyzed period, employment grew year on year. The dynamics of changes ranged from 10% in 2019 to nearly 43% in 2016, when the highest increase in employment in the sector in nominal terms was at the level of 64,000.BPO, SSC / GBS, IT, R&D centers generated...
-
The SEM images of Ce0.8La0.2O2 nanocatalyst infiltrated with 10wt.% Ni prepared using soft template method
Open Research DataThe dataset includes SEM images of Ce0.8La0.2O2-s nanopowder (nanoparticles) prepared using soft template method and infiltrated to 10wt.% Ni in the catalyst. CTAB was used as a micelle-based templating agent. The powder was precipitated from aqueous nitrate solution using NaOH solution and 250xCMC (critcal micelle concentration) of CTAB. Precipitate...
-
Depth profile of the gold-silver bimetallic structures
Open Research DataSilver and gold bimetallic layers were deposited on a silicon substrate by magnetron sputtering method. Both, Au and Ag layers had 3 nm of thickness. That prepared nanostructures were measured by XPS method. To obtain a depth profile of chemical composition, an Argon ion (Ar+) gun was used for etching surface of sample. Each cycle of etching takes 30...
-
XRD and electrochemical results for MoO3 films deposited using pulsed laser deposition system
Open Research DataThe attached data contains XRD and electrochemical results for MoO3 films deposited on fluorine-doped tin oxide glasses. Films were deposited using a pulsed laser deposition system at different conditions. Part of the samples was deposited at room temperature and then annealed at 575°C for given times (samples labeled PLD_RT_575C_xmin, where x stands...
-
Wpływ kierowcy na opór toczenia samochodu
PublicationW pracy omówiono wpływ zachowań kierowcy na opory toczenia pojazdu w ruchu drogowym. Można tu wyróżnić styl jazdy kierowcy oraz jego dbałość o pojazd. Przedstawiono wzrost oporu toczenia w aspekcie dynamicznego przyspieszania oraz szybkiej jazdy na zakręcie. Przeanalizowano także wpływ na opór toczenia takich czynników jak: ciśnienie w ogumieniu obciążenie promieniowe, zbieżność kół jezdnych samochodu oraz zużycie ogumienia.
-
Impact of blocking layer on DSSC performance based on new dye -indolo[3,2,1-jk]carbazole derivative and N719
Publication -
On the validation of the LS-DYNA Geo Metro numerical model
PublicationThe paper presents experiences gained during work with numerical model of Geo Metro vehicle used for simulations of crash tests with road safety barriers. Attention is drawn to the subject of tire/wheel breakage during collision events. Some methods for improvement of the model are presented in the paper. Several results for the normative vehicle numerical tests are introduced. Simulations were carried out using LS-DYNA finite...
-
Facile preparation of extremely photoactive boron-doped TiO2 nanotubes arrays
PublicationDoping of TiO2 nanotube arrays with boron was realized via electrochemical treatment of as-anodized titania immersed in electrolyte containing boric acid. The photoactivity of doped and pure titania was examined by means of photoelectrochemical and photocatalytic response under UV-vis irradiation. The results showed that photocurrent density of B-TNTs is remarkably higher (7.5 times) than density of pure TiO2 nanotube arrays. Furthermore,...
-
Kinetics and mechanism of the chemically modified starches during gelatinization.
PublicationNative starch was silicated by means of microwave-assisted reactions with varying doses of reagents. Resulting products were characterized by DSC and HMR-relaxation methods. It was observed that the hydratation of the silicated starches during gelatinization decreases when compared to that of the native potato starch. The amount of unfrozen water for ungelitinizated silicated starches are less than in control samples. At the same...
-
Intelligent equalizer solution employing music genre and the room characteristics analysis
PublicationThe paper presents an intelligent equalizer solution based on room acoustic conditions and music genre analysis. A series of acoustic characteristic measurements are performed for checking the concept proposed. White noise (reference signal) and audio excerpts belonging to six music genres are utilized as excitation signals in measurements. This results in registration of frequency responses of rooms and reverberation times. Signals...
-
Approaching Secure Industrial Control Systems
PublicationThis study presents a systematic approach to secure industrial control systems based on establishing a business case followed by the development of a security programme. To support these two fundamental activities the authors propose a new method for security cost estimation and a security assessment scheme. In this study they explain the cost evaluation technique and illustrate with a case study concerning the assessment of the...
-
Residence time distribution in rapid multiphase reactors
PublicationResidence time distribution (RTD) provides information about average hydraulic residence time and the distribution of material in the reactor. A method for determining RTD for reactors with very short hydraulic residence times is deconvolution based on extraction of real RTD by the analysis of a non-ideal input signal. The mean residence time and dispersion were determined for the spinning fluids reactor (SFR). For the first time...
-
Autonomous Vehicle Navigation in Dense Urban Area in Global Positioning Context
PublicationAutonoumous vehicle services are likely to be adopted in dense urban area. Some research prove that autonomous transport might be capable of improving the transport needs of few times and as a consequence sustainability, congestion and safety may be improved. The world, hopefully is close to a transport revolution age. These studies are perhaps exaggerated, over-optimistic and far fro fully operational. The paper takes into account...