Filters
total: 1325
displaying 1000 best results Help
Search results for: MAGNETIC SEMICONDUCTORS
-
Development of an emulation platform for synchronous machine power generation system using a nonlinear functional level model
PublicationThe article presents the Power Hardware in the Loop (PHIL) approach for an autonomous power system analysis based on the synchronous generator model incorporating magnetic saturation effects. The model was prepared in the MATLAB/Simulink environment and then compiled into the C language for the PHIL platform implementation. The 150 kVA bidirectional DC/AC commercial-grade converter was used to emulate the synchronous generator....
-
KTaO3-based nanocomposites for air treatment
PublicationA series of single semiconductors and their nanocomposites combination (such as KTaO3 + CdSe + SrTiO3; KTaO3 + CdS +WO3; KTaO3 + CdS + MoS2) were prepared using hydrothermal route. Photocatalytic activity of as-prepared nanocomposites was estimated by photocatalytic degradation of toluene in the gas phase using light-emitting diodes (LEDs, 375 nm) in four subsequent cycles. The nanocomposites were characterized by scanning electron...
-
End-Of-Life Management of Photovoltaic Solar Modules
PublicationThe PV industry continues to push its credentials as a technology that addresses one of the fundamental challenges of our times – climate change. There are however two major concerns about this technology: first, the potential negative environmental impacts of energy used in the production stage and second, the possible shortage of the valuable materials in the future. The currently dominant semiconductor used in photovoltaic modules...
-
Wojciech Sadowski prof. dr hab. inż.
PeopleWojciech Sadowski (born 2 February 1954 in Ostaszewo, Poland), scientist, engineer, professor at Gdansk University of Technology, specialist in solid state body physics, nanotechnology, optoelectronics. In 1973 he completed his high school education at High School Nicolaus Copernicus in Chelmno. In 1979 he graduate from Leningrad Electrotechnical Institute in Russia (former Soviet Union) with specialism in dielectrics and semiconductors....
-
Flexomagneticity in Functionally Graded Nanostructures
PublicationFunctionally graded structures have shown the perspective of materials in a higher efficient and consistent manner. This study reports a short investigation by concentrating on the flexomagnetic response of a functionally graded piezomagnetic nano-actuator, keeping in mind that the converse magnetic effect is only taken into evaluation. The rule of mixture assuming exponential composition of properties along with the thickness...
-
A correlation between electron-hole pair radii and magnetomodulation of exciplex fluorescence in electron donor-electron acceptor organic systems
PublicationElectric field dependencies of electromodulated photoluminescence and magnitudes of the magnetic-field effect on photoluminescence havebeen measured in vacuum-evaporated films of m-MTDATA [4,4',4"-tris(N-(3-methylphenyl)-N-phenylamino)triphenylamine]:bathophe-nanthroline, m-MTDATA:BCP (bathocuproine), as well as 4,4',4"-tris[2-naphthyl(phenyl)amino]triphenylamine:BCP. The Sano-Tachiya-Noolandi-Hong extension of standard Onsager...
-
Evolution of Physical Properties of RE 3 Ni 5 Al 19 Family (RE = Y, Nd, Sm, Gd, Tb, Dy, Ho, and Er)
PublicationSingle crystals of RE3Ni5Al19 series (RE = Y, Nd, Sm, Gd, Tb, Dy, Ho, and Er) are grown using the Al self-flux method. The crystal structure is examined by both single crystal and powder X-ray diffraction. Physical properties are studied for the first time for RE3Ni5Al19 (RE = Y, Nd, Gd, Tb, Dy, Ho, and Er) by means of magnetic susceptibility, electrical resistivity, and heat capacity measurements. Complex magnetic behaviors, with...
-
Horyzont energoelektroniczny obiektów morskich
PublicationW artykule zaprezentowano współczesne kierunki rozwoju energoelektroniki, w tym w szczególności dotyczące obiektów morskich. Przedstawiono podstawowe parametry aktualnie stosowanych w energoelektronice przyrządów półprzewodnikowych, jak również wykazano interdyscyplinarny charakter rozwoju tej dziedziny. Na przykładzie wybranych urządzeń energoelektronicznych przedstawiono ich komercyjne zastosowania oraz podział i miejsce w łańcuchu...
-
EFFECT OF WORKING FLUID SELECTION ON THERMAL PERFORMANCE OF HEAT EXCHANGER FILLED BY THE POROUS MATERIAL
PublicationThermal management of electronics semiconductor technologies that are located i.e. in a novel marine power plants or computer server rooms become very important issue for designers of such systems. Motivation and need for research in development of novel cooling strategies for modern electronics is of paramount importance. Heat exchangers filled by the porous material are a novel research topic in current heat pipe science. The...
-
Interferometric Sensor of Wavelength Detuning Using a Liquid Crystalline Polymer Waveplate
PublicationOperation of a polarization interferometer for measurement of the wavelength changes of a tunable semiconductor laser was investigated. A lambda/8 waveplate made from liquid crystalline polymer is placed in one of interferometers’ arms in order to generate two output signals in quadrature. Wavelength was measured with resolution of 2 pm in the wavelength range 628–635 nm. Drift of the interferometer, measured in the period of 500...
-
Crystal structure and low-energy Einstein mode in ErV2Al20 intermetallic cage compound
PublicationSingle crystals of a new ternary aluminide ErV2Al20 were grown using a self-flux method. The crystal structure was determined by powder X-ray diffraction measurements and Rietveld refinement, and physical properties were studied by means of electrical resistivity, magnetic susceptibility and specific heat measurements. These measurements reveal that ErV2Al20 is a Curie-Weiss paramagnet down to 1.95 K with an effective magnetic...
-
About Unusual Diffraction and Thermal Self-Action of Magnetosonic Beam
PublicationThe dynamics of slightly diverging two-dimensional beams whose direction forms a constant angle θ with the equilibrium straight magnetic strength is considered. The approximate dispersion relations and corresponding links which specify hydrodynamic perturbations in confined beams are derived. The study is dedicated to the diffraction of a magnetosonic beam and nonlinear thermal self-action of a beam in a thermoconducting gaseous plasma....
-
Shape Memory Polyurethane Materials Containing Ferromagnetic Iron Oxide and Graphene Nanoplatelets
PublicationIntelligent materials, such as memory shape polymers, have attracted considerable attention due to wide range of possible applications. Currently, intensive research is underway, in matters of obtaining memory shape materials that can be actuated via inductive methods, for example with help of magnetic field. In this work, an attempt was made to develop a new polymer composite—polyurethane modified with graphene nanoplates and...
-
Synthesis and physical properties of the 10.6 K ferromagnet NdIr3
PublicationThe magnetic, transport, and thermodynamic properties of NdIr3 are reported. Its PuNi3-type crystal structure (space group R−3m), with lattice parameters a= 5.3262(1)Å and c=26.2218(3)Å, was confirmed by powder x-ray diffraction. Our measurements indicate that NdIr3 exhibits a previously unreported paramagnetic to ferromagnetic phase transition below TC=10.6 K(determined by using the Arrott plot). The magnetic susceptibility obeys...
-
Ferromagnetism in Pr-rich binary Pr7Ru3 intermetallic compound
PublicationWe present the synthesis and experimental characterization of the binary intermetallic compound Pr7Ru3. The polycrystalline sample was prepared by arc melting pure Pr and Ru, followed by homogenization at 500 °C and 600 °C for 48 and 89 h, respectively. Powder x-ray diffraction confirms that Pr7Ru3 crystallizes in an orthorhombic crystal structure (Pnma, space group no. 62) with the lattice parameters: a = 7.3606(7) Å, b = 23.120(1)...
-
Surface Science - 2021/2022
e-Learning CoursesThe goal of the subject is the presentation of basic problems resulting from he existence of interfacebetween material objects and its surroundings. Discussion of the consequences arising from the existenceof surface energy. Analysis of possible applications of surface phenomena in technology. Understanding ofproblems and benefits resulting from decreasing dimensions of objects with the special emphasis on thesemiconductor band...
-
Method of determining the residual fluxes in transformer core
PublicationThe article presents the method of calculating the residual induction in transformer columns. The method is based on measurement of the magnetic induction in selected points around the transformer core. The values of residual induction are calculated as linear combination of the results of measurement.
-
Charakterystyka tranzystorów z węglika krzemu w wysokosprawnych przekształtnikach
PublicationPółprzewodnikowe przyrządy mocy z węglika krzemu (SiC) osiągnęły poziom technologiczny umożliwiający powszechne stosowanie w układach przekształtnikowych. W artykule omówiono ostatnie osiągnięcia dotyczące układów przekształtnikowych z przyrządami z węglika krzemu oraz wybrane wyniki badań realizowane na Politechnice Gdańskiej. W artykule opisano właściwości statyczne i dynamiczne tranzystorów MOSFET i JFET z węglika krzemu oraz...
-
Synthesis, structure and physical properties of new intermetallic spin glass-like compounds RE2PdGe3 (RE = Tb and Dy)
PublicationNew intermetallic compounds Tb2Pd1.25Ge2.75 and Dy2Pd1.25Ge2.75 have been synthesized using the arc-melting method. The crystallographic structure and magnetic, electronic transport, and thermal properties are reported. The crystal structure obtained from powder x-ray diffraction analysis suggests that these compounds crystallize in the AlB2-type structure (space group P6/mmm, no. 191) with lattice parameters a = 4.228 53(5)/4.230 54...
-
Polarization interferometer using a Liquid Crystalline Polymer waveplate for wavelength measurement
PublicationA two-beam polarization interferometer for measuring wavelength changes of a tunable semiconductor laser was designed, built and tested. This interferometer uses a λ/8 waveplate made from Liquid Crystalline Polymer in order to generate two output signals in quadrature. The λ/8 waveplate can be manufactured either on a beamsplitter face or on the mirror surface, reducing the cost and complexity of the optomechnical assembly. Experiment...
-
Currently Commercially Available Chemical Sensors Employed for Detection of Volatile Organic Compounds in Outdoor and Indoor Air
PublicationThe paper presents principle of operation and design of the most popular chemical sensors for measurement of volatile organic compounds (VOCs) in outdoor and indoor air. It describes the sensors for evaluation of explosion risk including pellistors and IR-absorption sensors as well as the sensors for detection of toxic compounds such as electrochemical (amperometric), photoionization and semiconductor with solid electrolyte ones....
-
Semi-adaptive feedback active control of MRI noise
PublicationA feedback controller is proposed for cancellation of magnetic resonance imaging (MRI) noise. The design of the controller takes into account specific features of the MRI noise signal. Simulation results show that a considerable rejection rate of the MRI noise can be obtained.
-
Improved finite element method for flow, heat and solute transport of Prandtl liquid via heated plate
PublicationIn the current study, a vertical, 3D-heated plate is used to replicate the generation of heat energy and concentration into Prandtl liquid. We discuss how Dufour and Soret theories relate to the equations for concentration and energy. In order to see how efectively particles, interact with heat and a solvent, hybrid nanoparticles are used. It does away with the phenomena of viscous dissipation and changing magnetic felds. The motivation...
-
CeIr3: superconductivity in a phase based on tetragonally close packed clusters
PublicationWe present the crystallographic analysis, superconducting and spectroscopic characterization, and theoretical modeling of CeIr3. Lattice parameters a = 5.2945(1) Å and c = 26.219(1) Å are found for the R-3m symmetry crystal structure, which are close to the literature values. CeIr3 is a moderate type-II superconductor (κ GL = 17, λ e–p = 0.65) below 2.5 K. Ce ions exhibit a strongly intermediate valence character as evidenced by...
-
In-situ optical diagnostics of boron-doped diamond films growth
PublicationInterferometry is a desirable method for in-situ measurement of thin, dielectric film growth, as it don't modify conditions of film deposition. Here we present interferometrical measurements of thickness of doped diamond films during Chemical Vapor Deposition (CVD) process. For this purpose we used a semiconductor laser with a 405nm wavelength. Additional ex-situ measurement using spectral interferometry and ellipsometry...
-
Metody pomiaru temperatury przedmiotów i ściernicy w procesie szlifowania jednotarczowego
PublicationW referacie przedstawiono metody pomiaru temperatury w szlifowaniu jednotarczowym z kinematyką docierania. W opracowanym rozwiązaniu wykorzystano małe, zasilane bateryjnie przyrządy rejestrujące temperaturę, tzw. logery pastylkowe o symbolu DS1922L produkcji firmy Dallas Semiconductor. Do pomiarów temperatury wykorzystano również kamerę termowizyjną. Zastosowanie czujników termoelektrycznych pozwoliło zarejestrować temperaturę...
-
Band engineering of BiOBr based materials for photocatalytic wastewater treatment via advanced oxidation processes (AOPs) – A review
PublicationSemiconductor based photocatalysts have been an efficient technology for water and wastewater remediation, addressing the concepts of green chemistry and sustainable development. Owing to narrow and suitable band structure, BiOBr is a promising candidate for efficient wastewater treatment via photocatalysis. Enhancement of photocatalytic properties can be obtained by various techniques like doping, element rich strategy, facet...
-
Development of novel optoelectronic sensory structures utilising colour centres in nanodiamonds and their interactions with analytes
PublicationThe goal of this dissertation was to develop and assess surface modifications of fluorescent nanodiamonds (NDs) for optical sensing. Three modification routes were tested, each aimed at a different application. Modification with poly-L-lysine (pLys) was verified for optical sensing of pH via an interrelationship between electrically negative (NV¯) and neutral (NV0) nitrogen-vacancy centres. Immobilisation of Ochratoxin A (OTA),...
-
3D intact knee model used in analysis of the medial meniscus biomechanics in the osteoarthritic knee joint - input text file for computation
Open Research DataThe finite element method was used to simulate the stance phase of the gait cycle. An intact knee model with original geometry and material parametetrs was prepared based on magnetic resonance scans of the left knee joint of a healthy volunteer. The file was created in Abaqus 6.14-2, but can be read in a text editor.
-
Pomiar naprężeń własnych metodą Barkhausena za pomocą sondy z wirującym polem magnetycznym
PublicationW pracy przedstawiono nowy sposób pomiaru naprężeń własnych w elementach konstrukcji z wykorzystaniem polowego efektu Barkhausena. Informację o stanie naprężeń uzyskano z analizy rozkładu kątowego natężenia efektu Barkhausena zmierzonego w sposób automatyczny poprzez sondę z wirującym polem magnetycznym. Przedstawiono zasadę działania i opis układu pomiarowego oraz przykłady wykorzystania tej metody w ocenie stanu naprężenia w...
-
Static electric multipole susceptibilities of the relativistic hydrogenlike atom in the ground state: Application of the Sturmian expansion of the generalized Dirac-Coulomb Green function
PublicationThe ground state of the Dirac one-electron atom, placed in a weak, static electric field of definite $2^{L}$ polarity, is studied within the framework of the first-order perturbation theory. The Sturmian expansion of the generalized Dirac-Coulomb Green function [R. Szmytkowski, J. Phys. B: At. Mol. Opt. Phys. 30, 825 (1997); erratum R. Szmytkowski, J. Phys. B: At. Mol. Opt. Phys. 30, 2747 (1997)] is used to derive closed-form analytical...
-
Determination of Complex Permeability of Silicon Steel for Use in High-Frequency Modeling of Power Transformers
Publication -
Separation of the effects of notch and macro residual stress on the MFL signal characteristics
PublicationMagnetic flux leakage (MFL) distribution for three configurations of samples has been investigated in order to study the influence of notch and plastic deformation separately as well as together. Samples have been made of S355 steel. The MFL signal measurements were carried out along the longest dimension of the sample over a length of 120 mm. Two components of magnetic field were measured: 1) tangential to the main axis and 2)...
-
Comparison of properties of magnetoacoustic emission and mechanical Barkhausen effects for P91 steel after plastic flow and creep
PublicationW artykule przedstawiono wyniki pogłębionej analizy sygnału szumowego efektu Barkhausena dla próbek ze stali krzemowej Fe-2%Si po deformacji plastycznej. Badane były próbki po walcowaniu na zimno powodującym odkształcenie względne w zakresie do 8%. Pierwsze podejście polegało na analizie w dziedzinie czasu widma badanego sygnału. Analiza ta została uzupełniona o analizę liczby zliczeń impulsów w funkcji napięcia progowego, zarówno...
-
Modeling of effect of plastic deformation on Barkhausen noise and magnetoacoustic emission in iron with 2% silicon
PublicationW modelowaniu zaadaptowano model Alessandro-Beatrice-Bertotti-Montorsi dla opisu ruchu granic nie-180 stopniowych oraz model Jiles-Atherton dla opisu wpływu plastycznej deformacji na natężenie efektu Barkhausena oraz emisji magnetoakustcznej.
-
An in-depth study of the Barkhausen emission signal properties of the plastically deformed Fe-2%Si alloy
PublicationZbadana została korelacja między natężeniem emisji magnetoakustycznej a natężeniem mechanicznego efektu Barkhausena dla próbek ze stali P91 mających różną mikrostrukturę na skutek plastycznego płynięcia w temperaturze pokojowej lub na skutek przyspieszonego pełzania w temperaturze 773K pod naprężeniem 290 KPa. Zakres deformacji plastycznej dla pierwszego zestawu próbek wynosił od 2% do 10,5% a dla drugiego od 0,85% do 10%. Oba...
-
Evaluation of Barkhausen Noise and Magnetoacoustic Emission Signals Properties for Plastically Deformed Armco Iron
PublicationArtykuł prezentuje wyniki badania wpływu różnych rodzajów deformacji plastycznej na właściwości magnetoakustyczne żelaza Armco. Badane były dwie serie próbek - pierwsza składała się ze wstępnie wyżarzonych próbek, które następnie były walcowane na zimno, w skład drugiej wchodziły natomiast próbki wycięte z komercyjnie dostępnej blachy wykonanej z żelaza Armco a następnie poddane obciążeniom rozciągającym. Walcowanie na zimno prowadzi...
-
Barkhausen noise properties measured by different methods for deformed Armco samples
PublicationPorównano właściwości sygnału napięciowego efektu Barkhausena (BN) uzyskanego za pomocą 'sondy punktowej' (użytecznej dla badań przemysłowych) oraz cewki otaczającej badany materiał. W pierwszej metodzie mierzono trzy wielkości: V1 - napięcie skuteczne, Nc - liczba impulsów, V2 - napięcie kontrolne z cewki. W drugiej metodzie z napięcia indukowanego w cewce wyznaczano pętlę histerezy B(H), obwiednie z napięcia skutecznego a także...
-
Computer simulation of induction hardening of moving flat charge
Publication -
Possibility of Application of Magnetoacoustic Emission for the Assessment of Plastic Deformation Level in Ferrous Materials
PublicationArtykuł prezentuje wyniki badań dotyczących możliwości zastosowana emisji magnetoakustycznej (EMA) do nieniszczącej oceny stopnia deformacji plastycznej próbek poddanych jednoosiowemu rozciąganiu. Przebadane zostały cztery różne materiały: stale 13HMF, CSN12021 i P91 oraz żelazo Armco. Badania pokazały, że różne parametry magnetyczne i magnetoakustyczne badanych materiałów mogą zmieniać się w rożny sposób, jednakże zawsze obserwuje...
-
Low current transformer utilizing Co-based amorphous alloys
PublicationMetal oxide surge arresters have been widely used for protection of power system networks against overvoltages due to atmospheric discharges or malfunction of devices connected to the network. During its operation a surge arrester structure is degradated, what can be observed as an increase of a surge arrester leakage current. Paper presents an implementation of a new, high-permeability, Co64Fe4Ni1Si15B14 amorphous alloy as a current...
-
Low Current Transformer Utilizing Co-Based Amorphous Alloys
PublicationMetal oxide surge arresters have been widely used for protection of power system networks against overvoltages due to atmospheric discharges or malfunction of devices connected to the network. During its operation a surge arrester structure is degradated, what can be observed as an increase of a surge arrester leakage current. Paper presents an implementation of a new, high-permeability, Co64Fe4Ni1Si15B14 amorphous alloy as a current...
-
Assessment with mechanical Barkhausen effect of residual stress in grain oriented polycrystalline 3% Si-Fe sheet
PublicationW tym artykule zostały opisane badania naprężeń resztkowych w blachach wykonanych z 3% si-fe o zorientowanym ziarnie za pomocą mechanicznego efektu barkhausena (mebn). badano blachy o 3 różnych orientacjach ziaren względem głównej osi próbki: 0, 45, 90 stopni. badania mebn przeprowadzano wzbudzając drgania skrętne oraz drgania gięte. zmierzone maksima obwiedni napięcia skutecznego mebn znajdują się dla badanych próbek w regionie...
-
Impact of Tensile and Compressive Stress on Classical and Acoustic Barkhausen Effects in Grain-Oriented Electrical Steel
PublicationIn this paper, we present the results of the investigation of impact of tensile and compressive stress on the classical Barkhausen effect, magnetoacoustic emission (MAE) signal properties, and B(H) hysteresis loops for grain-oriented (GO) electrical steel. Samples have been glued to a nonmagnetic steel bar and stressed within elastic range (±800 μdef) by means of four-point bending method. The samples were cut out in two directions...
-
How to render FDTD computations more effective using agraphics accelerator.
PublicationGraphics processing units (GPUs) for years have been dedicated mostly to real time rendering. Recently leading GPU manufactures have extended their research area and decided to support also graphics computing. In this paper, we describe an impact of new GPU features on development process of an efficient finite difference time domain (FDTD) implementation.
-
Adaptive CAD-Model Construction Schemes
PublicationTwo advanced surrogate model construction techniques are discussed in this paper. The models employ radial basis function (RBF)interpolation scheme or artificial neural networks (ANN) with a new training algorithm. Adaptive sampling technique is applied withrespect to all variables. Histograms showing the quality of the models are presented. While the quality of RBF models is satisfactory, theperformance of the ANN models obtained...
-
High-Frequency Proximity Losses Determination for Rectangular Cross-Section Conductors
Publication -
Assessment with mechanical Barkhausen effect of residual stress in grain oriented polycrystalline 3% Si-Fe sheet
PublicationZbadano za pomocą mechanicznego efektu Barkhausena poziom napręzeń wewnętrznych w plikrystalicznej płycie z 3% Si-Fe o zorientowanym ziarnie.
-
Barkhausen Noise Calculation by Hysteresis Model Parameters
PublicationPętla histerezy natężenia efektu Barkhausena wyliczono wykorzystując model histerezowy. Założono, iż straty energii na efekt Barkhausena zależą od szybkości granicy domenowej oraz od częstości występowania skoków Barkhausena. Pokazano wyliczenia wykonane dla stali Fe-Si (ziarna zorientowane w kierunku [100] względem kierunku walcowania)
-
Nondestructive Characterization of 2CR-1Mo Steel Quality Using Magnetoacousting Emission
PublicationPrzedstawiono wyniki badań własności emisji magneto-akustycznej (EMA) oraz własności magnetycznych (pętla histerezy magnetycznej, efekt Barkhausena, magnetostrykcja) dla wycinków rur stali 2Cr-1Mo o różnym stopniu degradacji. Wykazano, iż początkowy etap degradacji skutkuje w obniżeniu natężenia EMA oraz magnetostrykcja także niewielką zmianą pola koercji i nie monotoniczną zmianą natężenia efektu Barkhausena).