Search
displaying 1000 best results Help
Search results for: ROUND TUBES
-
Comparative study on the effectiveness of various types of road traffic intensity detectors
PublicationVehicle detection and speed measurements are crucial tasks in traffic monitoring systems. In this work, we focus on several types of electronic sensors, operating on different physical principles in order to compare their effectiveness in real traffic conditions. Commercial solutions are based on road tubes, microwave sensors, LiDARs, and video cameras. Distributed traffic monitoring systems require a high number of monitoring...
-
Experimental investigation of heat transfer enhancement in straight and U-bend double-pipe heat exchanger with wire insert
PublicationIn this paper, the possibility of heat transfer enhancement in the U-bend exchanger was presented. Experimental research has been carried out for four individual heat exchanger constructions i.e. plain tube in tube, turbulized tube in tube, plain U-bend and U-bend with turbulator. Also, heat transfer experiments for various boundary conditions were performed to obtain reference values. In case of U-bend exchanger with and without...
-
Electronic states of tetrahydrofuran molecules studied by electron collisions
PublicationElectronic states of tetrahydrofuran molecules were studied in the excitation energy range 5.5-10 eV using the technique of electron energy loss spectroscopy in the gas phase. Excitation from the two conformations, C2 and Cs, of the ground state of the molecule are observed in the measured energy loss spectra. The vertical excitation energies of the 3(no3s) triplet state from the C2 and Cs conformations of the ground state of the...
-
Nowe technologie wykonywania pali.
PublicationPrzedstawiono najnowsze krajowe trendy w wykonawstwie pali fundamentowych. Skrótowo omówiono technologie wykonywania pali CFA, jet-grouting, Vibrex, wkręcanych Vibro-Fundex, Tubex oraz pali wierconych wielkośrednicowych.
-
Asynchronous Wide Area Multilateration System
PublicationA new method for a location service in the wide area multilateration (WAM) system is outlined. This method, which is called asynchronous WAM (AWAM), enables calculation of the geographical position of an aircraft without knowledge of relative time differences (RTDs) between measuring ground stations (sensors). The AWAM method is based on the measurement of round trip times (RTTs) between the aircraft and the serving ground station,...
-
Tuning of High Spin Ground State and Slow Magnetic Relaxation within Trimetallic Cyanide‐Bridged {Ni II x Co II 9− x [W V (CN) 8 ] 6 } and {Mn II x Co II 9− x [W V (CN) 8 ] 6 } Clusters
Publication -
Potential energy surfaces of the low-lying electronic states of the Li+LiCs system
PublicationAb initio quantum chemistry calculations are performed for the mixed alkali triatomic system. Global minima of the ground and first excited doublet states of the trimer are found and Born-Oppenheimer potential energy surfaces of the Li atom interacting with the LiCs molecule were calculated for these states. The lithium atom is placed at various distances and bond angles from the lithium-caesium dimer. Three-body nonadditive forces...
-
Marek Czachor prof. dr hab.
People -
Piotr Lorens prof. dr hab. inż. arch.
PeopleProf. Piotr Lorens - PhD, DSc., urban planner. Lecturer in urban design and development and - since 2007 - Head of the Department of Urban Design and Regional Planning at the Faculty of Architecture, Gdansk University of Technology. His university activities also include coordination of the research and EU Social Fund projects. Based on these projects he was responsible for organization and coordination of the post-graduate studies...
-
Frontispiece: Tuning of High Spin Ground State and Slow Magnetic Relaxation within Trimetallic Cyanide‐Bridged {Ni II x Co II 9− x [W V (CN) 8 ] 6 } and {Mn II x Co II 9− x [W V (CN) 8 ] 6 } Clusters
Publication -
Buckling analysis of a non-concentric double-walled carbon nanotube
PublicationOn the basis of a theoretical study, this research incorporates an eccentricity into a system of compressed double-walled carbon nanotubes (DWCNTs). In order to formulate the stability equations, a kinematic displacement with reference to the classical beam hypothesis is utilized. Furthermore, the influence of nanoscale size is taken into account with regard to the nonlocal approach of strain gradient and the van der Waals interaction...
-
Imunofan - RDKVYR peptide - stimulates skin cell proliferation and promotes tissue repair
PublicationRegeneration and wound healing are vital to tissue homeostasis and organism survival. One of the biggest challenges of today's science and medicine is finding methods and factors to stimulate these processes in the human body. Effective solutions to promote regenerative responses will accelerate advances in tissue engineering, regenerative medicine, transplantology, and a number of other clinical...
-
A NOTE ON ON-LINE RAMSEY NUMBERS FOR QUADRILATERALS
PublicationWe consider on-line Ramsey numbers defined by a game played between two players, Builder and Painter. In each round Builder draws an the edge and Painter colors it either red or blue, as it appears. Builder’s goal is to force Painter to create a monochromatic copy of a fixed graph H in as few rounds as possible. The minimum number of rounds (assuming both players play perfectly) is the on-line Ramsey number \widetilde{r}(H) of...
-
Impact of Temperature and Nanoparticle Concentration on Turbulent Forced Convective Heat Transfer of Nanofluids
PublicationTheoretical analysis of the influence of nanoparticles and temperature on the average Nusselt (Nu) number and the average heat transfer coefficient (HTC) during the turbulent flow of nanofluid in a horizontal, round tube was carried out. The Nu number is a function of the Reynolds (Re) number and the Prandtl (Pr) number, which in turn are functions of the thermophysical properties of the liquid and the flow conditions. On the other...
-
HEAT TRANSFER CHARACTERISTICS OF ENHANCED SHELL AND COIL HEAT EXCHANGER
PublicationIn the paper authors presented their own constructions of shell and tube heat exchangers with intensified heat transfer. The shell and coils heat exchangers are in common use in heat ventilations and air conditioning systems. Those types of recuperators are quite simple constructions, the low value of pressure drops and good conditions of heat transfer. The present study shows an experimental investigation of the heat transfer...
-
Posadowienie obiektów mostowych na palach przemieszczeniowych formowanych w gruncie
PublicationPraca dotycząca posadowienia obiektów mostowych na palach przemieszczeniowych formowanych w gruncie. W pracy omówiono technologie pali Franki, Vibro-Fundex, Vibrex, Tubex i FDP oraz podano przykłady realizacji obiektów mostowych na tych palach.
-
Ferro- and antiferro-magnetism in (Np, Pu)BC
PublicationTwo new transuranium metal boron carbides, NpBC and PuBC, have been synthesized. Rietveld refinements of powder XRD patterns of {Np,Pu} BC confirmed in both cases isotypism with the structure type of UBC. Temperature dependent magnetic susceptibility data reveal antiferromagnetic ordering for PuBC below T-N = 44 K, whereas ferromagnetic ordering was found for NpBC below T-C = 61 K. Heat capacity measurements prove the bulk character...
-
Traffic Noise Analysis Applied to Automatic Vehicle Counting and Classification
PublicationProblems related to determining traffic noise characteristics are discussed in the context of automatic dynamic noise analysis based on noise level measurements and traffic prediction models. The obtained analytical results provide the second goal of the study, namely automatic vehicle counting and classification. Several traffic prediction models are presented and compared to the results of in-situ noise level measurements. Synchronized...
-
Justyna Martyniuk-Pęczek dr hab. inż. arch.
PeopleJustyna Martyniuk-Peczek, Ph.D., D.Sc. Associate Professor Department of Urban Design and Regional Planning, Faculty of Architecture Gdansk University of Technology My academic and research activity has been concentrated around one specialty — urban planning, however it involves an interdisciplinary reference to other fields, such as lighting and the science of management. In terms of quantity, my academic work...
-
A Microwave Sensor with Operating Band Selection to Detect Rotation and Proximity in the Rapid Prototyping Industry
PublicationThis paper presents a novel sensor for detecting and measuring angular rotation and proximity, intended for rapid prototyping machines. The sensor is based on a complementary split-ring resonator (CSRR) driven by a conductor-backed coplanar waveguide. The sensor has a planar topology, which makes it simple and cost-effective to produce and accurate in measuring both physical quantities. The sensor has two components, a rotor, and...
-
Vident-synth: a synthetic intra-oral video dataset for optical flow estimation
Open Research DataWe introduce Vident-synth, a large dataset of synthetic dental videos with corresponding ground truth forward and backward optical flows and occlusion masks. It can be used for:
-
Modelling of wave propagation in composite plates using the time domain spectral element method
PublicationW pracy przedstawiono wyniki obliczeń propagacji fali sprężystej w płycie kompozytowej modelowanej z wykorzystaniem czasowego sformułowania metody elementów spektralnych
-
Assessment of rod behavior theories used in spectral finite element modeling
PublicationW pracy przedstawiono teorie prętów i przedstawiono ich przydatnośc w analizie propagacji fal sprężystych z wykorzystaniem metody spektralnych elementów skończonych.
-
Experimental and numerical study on damage detection in an L-joint using guided wave propagation
PublicationW pracy zaprezentowano metodę wykrywania i lokalizacji uszkodzeń w konstrukcji ramowej za pomocą podłużnych i poprzecznych fal sprężystych. Przeprowadzono badania numerczyne i eksperymentalne na modelu bez uszkodzenia oraz na modelu z wsprowadzonym nacięciem. Do modelowania zastosowano metodę elementów spektralnych. W pracy przedstawiono sformułowanie nowego element spektralnego dla ram płaskich bazującego na teorii pręta Mindlina...
-
Fast bubble dynamics and sizing
PublicationSingle bubble sizing is usually performed by measuring the resonant bubble response using the Dual Frequency Ultrasound Method. However, in practice, the use of millisecond-duration chirp-like waves yields nonlinear distortions of the bubble oscillations. In comparison with the resonant curve obtained under harmonic excitation, it was observed that the bubble dynamic response shifted by up to 20 percent of the resonant frequency...
-
Assessment of flexural beam behaviour theories used for dynamics and wave propagation problems
PublicationW pracy przedstawiono i porównano teorie belek zginanych począwszych od teorii elementarnych, aż do teorii wyższych rzędów. Przedstawiono krzywe dyspersi dla poszczególnych teorii i na ich podstawione oszacowano zakres stosowalności danej teorii.
-
Experimental and numerical study on damage detection in an L-joint using guided wave propagation
Publication -
Application of continuous wavelet transform in vibration based damage detection method for beams and plates
Publication -
The dynamic analysis of a cracked Timoshenko beam by the spectral element method
Publication -
Longitudinal wave propagation. Part I—Comparison of rod theories
Publication -
Wave propagation in a sensor/actuator diffusion bond model
Publication -
Longitudinal wave propagation. Part II—Analysis of crack influence
Publication -
Application of continuous wavelet transform in vibration based damage detection method for beams and plates
PublicationW artykule zaprezentowano metodę lokalizacji uszkodzeń w konstrukcjach belkowych i płytowych bazującą na analizie falkowej. Wyznaczono postacie drgań badanych konstrukcji. Postacie drgań konstrukcji belkowej zostały przeanalizowane jednowymiarową transfrormatą falkową. Sformułowano dwuwymiarową transformatę falkową, którą zastosowano do postaci drgań konstrukcji płytowej.
-
Wave propagation modelling in 1D structures using spectral finite elements
PublicationW artykule omówiono modele propagacji fal wzdłużnych i poprzecznych w prętach oparte na dwóch sformułowaniach (w dziedzinie częstości i w dziedzinie czasu) metody elemntów spektralnych. Porównano otrzymane wyniki z wynikami eksperymentu.
-
Longitudinal wave propagation. Part II, Analysis of crack influence
PublicationW pracy analizowano wpływ pęknięć zmęczeniowych na propagacje fali wzdłużnej w prętach. Opracowano nowe typy element ów spektralnych oparte na teorii elementarnej, Love'a, Mindlina i trójpostaciowej.
-
Longitudinal wave propagation. Part I - Comparison of rod theories
PublicationW pracy przedstawiono modele spektralnych elementów skończonych do analizy propagacji fali wzdłuznej w pretach. Opracowano modele wykorzystujace teorię elementarną, teorie Love'a, teorie Mindlina oraz teorię trójpostaciową.
-
The dynamic analysisi of cracked Thimoshenko beam by the spectral element method.
PublicationW pracy przedstawiono model belli Timoshenko z pęknięciem poprzecznym oparty o metodę elementów spektralnych. Przedstawiono wyniki propagacji fali sprężystej i jej interakcję z pęknięciem.
-
VIBRATION PARAMETERS FOR DAMAGE DETECTION IN STRUCTURES
PublicationThe aim of this paper is to examine how damage indicators are sensitive to changing number of frequencies and mode shapes and also to number and location of measurement points. The influence of measurement errors was also analyzed for all cases. For the analysis, those damage indicators are chosen which use changes in such modal parameters as natural frequencies and mode shapes and also differences between the curvatures of the damaged...
-
High frequency dynamics of an isotropic Timoshenko periodic beam by the use of the Time-domain Spectral Finite Element Method
PublicationIn this work results of numerical simulations and experimental measurements related to the high frequency dynamics of an aluminium Timoshenko periodic beam are presented. It was assumed by the authors that the source of beam structural periodicity comes from periodical alterations to its geometry due to the presence of appropriately arranged drill-holes. As a consequence of these alterations dynamic characteristics of the beam...
-
Considerations about the applicability of the Reynolds equation for analyzing high-speed near field levitation phenomena
Publicationequation for analyzing near field levitation (NFL) phenomena. Two separate approaches were developed, experimentally verified, and applied to meet the research objective. One was based on the Reynolds equation and the other was based on general conservation equations for fluid flow solved using computational fluid dynamic (CFD). Comparing the calculation results revealed that, for certain operating conditions, differences in the...
-
Development of a Peptide Derived from Platelet-Derived Growth Factor (PDGF-BB) into a Potential Drug Candidate for the Treatment of Wounds
PublicationObjective: This study evaluated the use of novel peptides derived from platelet-derived growth factor (PDGF-BB) as potential wound healing stimulants. One of the compounds (named PDGF2) was subjected for further research after cytotoxicity and proliferation assays on human skin cells. Further investigation included evaluation of: migration and chemotaxis of skin cells, immunological and allergic safety, the transcriptional analyses...
-
A brief note on monotonic and fatigue fracture events investigation of thin-walled tubular austenitic steel specimens via fracture surface topography analysis (FRASTA)
PublicationThe main objective of this short communication is to show the fracture progression in each loading case and complement knowledge about fracture mechanisms underpinning the tensile and fatigue performance of thin-walled tubes. For this purpose, the fracture surface topography analysis (FRASTA) method was used in the thin-walled tubular austenitic stainless-steel specimens. Two cases were analyzed: monotonic tension, and uniaxial...
-
Non-adiabatic coupling elements between the diatomic silver anion and neutral silver dimer plus continuum electron
Open Research DataThe process of a two-channel decay of the diatomic silver anion (Ag2-), namely the spontaneous electron ejection giving Ag2 + e- and the dissociation leading to Ag- + Ag is theoretically studied. The ground state potential energy curves (PECs) of the neutral silver dimer and anionic silver diatomic molecule are calculated using the single reference...
-
Magnetizabilities of relativistic hydrogenlike atoms in some arbitrary discrete energy eigenstates
PublicationWe present the results of numerical calculations of magnetizability of the relativistic hydrogenlike atoms. Exploiting the analytical formula for $\chi$ we have found the values of the magnetizability for the ground state and for the first and the second set of excited states of the atom. The results for ions with the atomic number $0
-
Dynamic polarizability of the relativistic hydrogenlike atom: Application of the Sturmian expansion of the Dirac-Coulomb Green function
PublicationWe utilize the Sturmian expansion of the Dirac-Coulomb Green function [R. Szmytkowski, J. Phys. B 30, 825 (1997)] to obtain components of the dynamic dipole polarizability tensor of the relativistic hydrogenlike atom in the ground state. It is found that the tensor may be expressed in terms of two independent quantities: a scalar polarizability and a vector polarizability, the latter being of the relativistic origin. In the static...
-
Problems of Measuring Gas Content in Oil in a Two-Phase Flow: A Review
PublicationIn view of the necessity of measuring the air content in oil in two-phase flows in the context of general industry, a review of the most popular methods of measuring the air content in oil was carried out. This review includes an assessment of their advantages and disadvantages and of whether they meet criteria such as the degree of filling, the size and number of bubbles, verification, the absence of additional pressure drops,...
-
Concrete temperature measurements of cubic specimens cured under isothermal and semi-adiabatic conditions
Open Research DataThe DataSet contains temperature measurements of concrete cubes (150 x 150 x 150 mm) cured under isothermal and semi-adiabatic conditions. The specimens were moulded from six types of concrete mixtures produced in the laboratory conditions. Mix #1: Portland cement CEM I 42.5R and gravel aggregate, mix #2: CEM I 42.5R and basalt aggregate, mix#3: Portland-composite...
-
Stężenie formaldehydu w wodach spływnych z arterii komunikacyjnych, powierzchni dachów budynków i koron drzew, wodach gruntowych i rzecznych oraz w opadach i osadach atmosferycznych na terenie aglomeracji miejskich = Formaldehyde in road runoff, roof runoff, ground water, river, atmospheric precipitation and deposition from highly urbanized regions
PublicationOznaczono stężenie formaldehydu w próbkach wód opadowych, spływnych z arterii komunikacyjnych, powierzchni dachów budynków i koron drzew, wód gruntowych i cieków wodnych oraz w próbkach śniegu, szronu i sadzi. Próbki pobierano przez okres 7 miesięcy w trakcie wystąpienia opadu lub osadu atmosferycznego lub tuż po jego ustąpieniu. Pomiar zawartości formaldehydu wykonywano stosując metodę szybkich testów spektrofotometrycznych w...
-
Multi-mode vibronic interactions in the five lowest electronic states of the fluorobenzene radical cation
PublicationThe multi-mode vibronic interactions between the five lowest electronic states of the fluorobenzene radical cation are investigated theoretically, based on ab initio electronic structure data, and employing the linear vibronic coupling model. Low-energy conical intersections, and strong vibronic couplings are found to prevail within the set of X-A and B-C-D cationic states, while the interactions between these two sets of states...
-
Prediction of protein assemblies, the next frontier: The CASP14‐CAPRI experiment
PublicationWe present the results for CAPRI Round 50, the 4th joint CASP-CAPRI protein assembly prediction challenge. The Round comprised a total of 12 targets, including 6 dimers, 3 trimers, and 3 higher-order oligomers. Four of these were easy targets, for which good structural templates were available either for the full assembly, or for the main interfaces (of the higher-order oligomers). Eight were difficult targets for which only distantly...