Search
Filters
total: 2580
displaying 1000 best results Help
Search results for: operational excellence
-
The resilient city in architectural engineering education: a joint design studio between Gdańsk and Chalmers universities of technology
PublicationChallenges to society, such as those posed by climate change require a new approach to the education of the engineer-architect. Contemporary solutions should serve future generations and that is why the idea of the resilient city should be discussed and implemented, both in theory and in practice. It is necessary to teach students to design urban structures in such a way that they are resilient to dynamically changing conditions....
-
Marine propeller shaft bearings under low-speed conditions: water vs. oil lubrication
PublicationThe bearings used in shipbuilding, hydropower, and water pumps have undergone a metamorphosis in recent decades. Because of environmental regulations, lubrication with grease or mineral oil is prohibited. Thus, the standard solutions include water-lubricated bearings with polymer bushings or sealed systems lubricated with oil. When properly designed, assembled, and operated, bearings can operate reliably for years. However, specific...
-
Analysis of Failures of High Speed Shaft Bearing System in a Wind Turbine
PublicationDuring the operation of wind turbines with gearbox of traditional configuration, consisting of one planetary stage and two helical stages high failure rate of high speed shaft bearings is observed. Such a high failures frequency is not reflected in the results of standard calculations of bearing durability. Most probably it can be attributed to atypical failure mechanism. The authors studied problems in 1.5 MW wind turbines of...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublicationThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublicationThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Application of the fluid–structure interaction technique for the analysis of hydrodynamic lubrication problems.
PublicationFluid–structure interaction technique seems to be one of the most promising possibilities for theoretical analysis of lubrication problems. It allows coupling of different physical fields in one computational task, taking into account the interaction between them. In this article, two sets of fluid–structure interaction analyses focusing on the bearing performance evaluation are presented. One analysis was applied to a water-lubricated...
-
Performance of a plate heat exchanger operated with water-Al2O3 nanofluid
PublicationThis study is focused on experimental investigation of a selected type of brazed plate heat exchanger (PHEx). The main aim of the paper was to experimentally check the ability of nanofluids to enhance the performance of PHEx. A typical water-Al2O3 nanofluid was tested and compared to that of the base fluid, i.e. water. Nanoparticles were tested at the concentration of 0.1% and 1% by weight. Impact of the 1 day and 3 days break...
-
Adaptive Identification of Underwater Acoustic Channel with a Mix of Static and Time-Varying Parameters
PublicationWe consider the problem of identification of communication channels with a mix of static and time-varying parameters. Such scenarios are typical, among others, in underwater acoustics. In this paper, we further develop adaptive algorithms built on the local basis function (LBF) principle resulting in excellent performance when identifying time-varying systems. The main drawback of an LBF algorithm is its high complexity. The subsequently...
-
Wideband Highly-Selective Bandpass Filtering Branch-Line Coupler
PublicationThis paper presents a novel design of a wideband highly-selective bandpass filtering branch-line coupler (FBLC). By integrating a coupled microstrip line, and an open-ended stub at each port of a single-section BLC, bandpass filtering characteristics with excellent selectivity and broad operating bandwidth have been achieved. The proposed circuit has been verified through EM simulations and physical measurements of the fabricated...
-
Adhesive compliance effect in mode I separation:Profilometry approach
PublicationThe effect of adhesive compliance on the deflection of a loaded, bonded beam was studied using laser profilometry. Experimental data obtained were compared with both Euler-Bernoulli (encastré) and Winkler (one parameter elastic foundation) models. A third, analytical, 2D model, based on shear within the adhesive layer (two parameter elastic foundation), was introduced. Finite element analysis (FEA) was also used to study the effect...
-
Effect of electron count and chemical complexity in the Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor
PublicationHigh-entropy alloys are made from random mixtures of principal elements on simple lattices, stabilized by a high mixing entropy. The recently discovered body-centered cubic (BCC) Ta-Nb-Hf-Zr-Ti high-entropy alloy superconductor appears to display properties of both simple crystalline intermetallics and amorphous materials; e.g., it has a well-defined superconducting transition along with an exceptional robustness against disorder....
-
Spectroscopic and magnetic studies of highly dispersible superparamagnetic silica coated magnetite nanoparticles
PublicationSuperparamagnetic behavior in aqueously well dispersible magnetite core-shell Fe3O4@SiO2 nanoparticles is presented. The magnetic properties of core-shell nanoparticles were measured with use of the DC, AC magnetometry and EPR spectroscopy. Particles were characterized by HR-TEM and Raman spectroscopy, showing a crystalline magnetic core of 11.5 ± 0.12 nm and an amorphous silica shell of 22 ± 1.5 nm in thickness. The DC, AC magnetic...
-
Recurrent potential pulse technique for improvement of glucose sensing ability of 3D polypyrrole
PublicationIn this work, a new approach for using a 3D polypyrrole (PPy) conducting polymer as a sensing material for glucose detection is proposed. Polypyrrole is electrochemically polymerized on a platinum screen-printed electrode in an aqueous solution of lithium perchlorate and pyrrole. PPy exhibits a high electroactive surface area and high electrochemical stability, which results in it having excellent electrocatalytic properties. The...
-
Material Flow Analysis in a cooked mussel processing industry
PublicationGalicia (NW Spain) is an ideal environment for mussel culture owing to its excellent natural conditions. It is the first Spanish and European mussel producer and the second worldwide after China. More than 50% of the mussel collected in Galicia is used in the processing industry, which produces different products, as cooked mussel that is canned, frozen or used in the food industry. In this paper a methodology based on Life Cycle...
-
Polymer electrolytes with ionic liquids
PublicationSolid polymer electrolytes are solutions of salts in the macromolecular polymeric compound. Excellent process ability, flexibility, non-flammability and non-reactivity make them ideal materials for electrochemical devices. The problem in their use is limited conductivity. It increases with increasing salt concentration in the polymer, but at the same time the condition is to increase the glass transition temperature of the polymer...
-
Review—Advances in Rechargeable Lithium-Ion Batteries Utilizing Polyoxometalate-Functionalized Nanocarbon Materials
PublicationPolyoxometalates (POMs) are inorganic nanoclusters that consist of oxygen and transition metals. These nanoclusters serve as excellent precursors for creating electrode materials that contain transition metals. Additionally, the interaction between POMs and carbon substrates produces positive synergistic effects. There has been considerable attention on employing POMs and carbon nanostructures (for example carbon nanotubes, graphene,...
-
MXene-based materials for removal of antibiotics and heavy metals from wastewater– a review
PublicationAs a novel family of 2D materials, MXenes provide an extensive variety of applications in water and effluent treatment due to their distinctive properties and attractive applicability, including superior electrical conductivity, higher thermal stability, hydrophilicity, and high sorption-reduction capacity. Their excellent sorption selectivity makes them perfect for removing hazardous contaminants. Currently, MXene-based materials...
-
Exfoliated graphite with spinel oxide as an effective hybrid electrocatalyst for water splitting
PublicationThe aim of the conducted research was to develop hybrid nanostructures formed from MnCo2O4 and exfoliated graphite. Carbon added during the synthesis allowed for obtaining a well-distributed MnCo2O4 particle size with exposed active sites contributing to the increased electric conductivity. The influence of the weight ratios of carbon to a catalyst for hydrogen and oxygen evolution reactions was investigated. The new bifunctional...
-
Obtaining of Coumarone-Indene Resins Based on Light Fraction of Coal Tar. 4. Bitumen-Polymer Blends with Participation of Coumarone-Indene Resins with Epoxy Groups
PublicationUsing light fraction of coal tar (5.75 wt % of coumarone and 44.45 wt % of indene), glycidyl methacrylate and styrene, the coumarone-indene resin with epoxy groups (CIRE) has been synthesized. Monoperoxy derivative of diglycidyl ether Bisphenol A (PO) was used as an initiator. The possible formation of CIRE has been studied on the model systems consisting of PO, glycidyl methacrylate, indene or coumarone, or styrene, or mixture...
-
MESOSCALE FUNCTIONS OF GPS SLANT DELAY
PublicationThe paper presents a computer module for GPS slant delay determination using data from COAMPS (Coupled Ocean/Atmosphere Mesoscale Prediction System) mesoscale non-hydrostatic model of the atmosphere which is run on IA64 Feniks computer cluster in the Department of Civil Engineering and Geodesy of the Military University of Technology. The slant delay is the result of integrating the ray (eikonal) equation for the spatial function...
-
Structural Health Monitoring System for Suspension Footbridge
PublicationThe article presents the structural health monitoring (SHM) system installed in a footbridge in Radom. The main reason for the need for fitting of such a system was failed acceptance tests of the bridge. While under a dynamic load consisting of a group of 12 pedestrians jumping on the bridge, the bridge developed vibration during which acceleration of the deck of up to 4.5 m/s2 was recorded. Such behavior of the footbridge causes...
-
Enhancing Security of Advanced Metering Infrastructure by Introducing Threshold Attendance Protocol
PublicationThe industry pushes towards smart grid systems in order to resolve current limitations of the unidirectional legacy power grid infrastructure. By introducing Advanced Metering Infrastructure (AMI) as an integral part of the smart grid solution, the utility company obtains an invaluable tool to optimize its network, lower the operational costs, and improve quality of service. Unfortunately, introducing two-way communication poses...
-
Revalorization of the Szewalski binary vapour cycle
PublicationThe aim of the paper is to revalorizate of the Szewalski binary vapour cycle by analysing thermodynamical and operational parameters of this cycle. This was carried by accessible numerical CFM (Computational Flow Mechanics) codes type, by step-by-step modeling of separates apparatus. The binary vapour cycle is providing steam as the working fluid in the high temperature part of the cycle, while another fluid - a low boiling point...
-
Stanowisko wizualizacji zdarzeń w systemie STRADAR – realizacja i funkcje dla operatora
PublicationIt is crucial for the Border Guard to be equipped with a communication-teleinformatic infrastructure designed to support them in efficient realization of their operational tasks. STRADAR – a system which results are presented in this paper – is such an infrastructure. It is a distributed solution for the maritime division of the border guard. The system, with the use of a network of sensors located in both stationary and mobile...
-
Novel structure and design of enhanced-bandwidth hybrid quadrature patch coupler
PublicationA novel structure and design optimization procedure of an enhanced-bandwidth hybrid quadrature patch coupler is proposed. Improved performance of the circuit has been obtained by parameterizing the coupler sections using splines, which introduces additional degrees of freedom. Due to computational complexity of the parameter adjustment problem, a sequential design procedure is applied. In each iteration, a selected number of spline...
-
Employment of a Nonlinear Adaptive Control System for Improved Control of Dissolved Oxygen in Sequencing Batch Reactor
PublicationA proper control in a complex system, such as Wastewater Treatment Plant (WWTP) with each year is becoming increasingly important. High quality control can minimize an environmental impact as well as reduce operational costs of the WWTP. One of the core issues is providing adequate dissolved oxygen (DO) concetration for microorganisms used in a treatment process. An aeration process of the wastewater realised by an system consisting...
-
Performance Analysis of Multicast Video Streaming in IEEE 802.11 b/g/n Testbed Environment
PublicationThe aim of the work is to analyse capabilities and limitations of different IEEE 802.11 technologies (IEEE 802.11 b/g/n), utilized for both multicast and unicast video streaming transmissions directed to mobile devices. Our preliminary research showed that results obtained with currently popular simulation tools can be drastically different than these possible in real-world environment, so, in order to correctly evaluate performance...
-
Blast Charge Technique as a Method of Soil Improving to Locate the New Supporting Runways
PublicationA quick and effective method of reinforcing the ground base designed for the construction of engineering structures used for performing various types of air operations was presented. It allows to use wastelands, wetlands, swamps, etc. for these purposes, thus creating a dispersed network of landing sites, increasing the access of large social groups to air transport and increasing their mobility.
-
Hydrodynamic reanalysis of sea level in the Baltic Sea using the PM3D model
Open Research DataThe data set contains the results of numerical modelling of sea level fluctuations in the Baltic Sea in the Baltic Sea since 1998. A long-term reanalysis was performed using a three-dimensional hydrodynamic model PM3D (Kowalewski and Kowalewska-Kalkowska, 2017), a new version of the M3D model (Kowalewski, 1997).
-
Coronas and Domination Subdivision Number of a Graph
PublicationIn this paper, for a graph G and a family of partitions P of vertex neighborhoods of G, we define the general corona G ◦P of G. Among several properties of this new operation, we focus on application general coronas to a new kind of characterization of trees with the domination subdivision number equal to 3.
-
Proposed Amendments to Reactive Energy Billing
PublicationThis paper describes possible amendments to the rules of reactive energy billing in the tariffs in Poland. Modifications in the tariffs to improve their motivational function for distribution system users are identified as the most expedient. New problems arising from distributed generator operations are also indicated. A billing method that can be effectively implemented at the occurrence of distorted voltage and current waveforms...
-
Algorytmy wyodrębniania składowych symetrycznych sygnału pomiarowego napięcia w przypadku asymetrii sieci trójfazowej
PublicationW artykule zaprezentowano działanie wybranych algorytmów wykorzystywanych do wyodrębniania składowych symetrycznych z sygnałów pomiarowych napięcia lub prądu w przypadku wystąpienia asymetrii trójfazowej sieci elektroenergetycznej. Weryfikacji działania algorytmów dokonano na podstawie badań symulacyjnych i laboratoryjnych w układzie w którym jako odbiornik zastosowano stojan maszyny asynchronicznej pierścieniowej. Określono wpływ...
-
Agnieszka Pastula Dr
PeopleAgnieszka received her masters degree in biology at Jagiellonian University (Poland). Besides standard university classes, she did multiple extracurricular research internships in both basic science and medical life sciences e.g. at Warsaw University, Jagiellonian University College of Medicine, University of Medical Sciences in Poznań and University Medical Center Utrecht, that provided her with excellent interdisciplinary training...
-
Application of RCD and AFDD in low-voltage electrical installations for protection against fire
PublicationThe paper presents the principles of application of residual current devices (RCDs) in protection against fire. The permissible rated residual operating current of RCDs is discussed. Limitations in the operation of RCDs in this type of protection are indicated. A new type of a protective device against fire – arc fault detection device (AFDD) – is described.
-
Analysis of the Heating Process of Hydraulic Motors during Start-Up in Thermal Shock Conditions
PublicationConditions that prevail during harsh winters and hot summers pose a serious challenge for machine designers building devices suitable for operation in extreme weather. It is essential for the designers and the users to define the principles and conditions for the safe operation of machines and devices with hydraulic drive in low ambient temperatures. Bearing in mind the above, the author tested the hydraulic motors in thermal shock...
-
The influence of IT-competency dimensions on job satisfaction, knowledge sharing and performance across industries
PublicationPurpose – Technology makes knowledge management easier. Knowledge sharing is essential for organizational development. Job satisfaction fosters knowledge sharing. Hence, this study aims to develop an understanding of the mutual relationship between knowledge sharing and job satisfaction when both are predicted by information technology (IT)-competency dimensions such as IT-operations, IT-knowledge and IT-infrastructure in the context...
-
PROBLEMY RACJONALNEGO ZASTOSOWANIA SYSTEMÓW DIAGNOZUJĄCYCH DO PODEJMOWANIA DECYZJI W FAZIE EKSPLOATACJI URZĄDZEŃ ENERGETYCZNYCH Z UWZGLĘDNIENIEM ZAGADNIEŃ KWANTOWYCH
PublicationW rozdziale przedstawiono najistotniejsze problemy pojawiające się w fazie projektowania, wytwarzania i eksploatacji systemów diagnozujących (SDG) urządzeń energetycznych (będących systemami diagnozowanymi – SDN), w przypadku przysposabiania ich do opracowania finalnej diagnozy eksploatacyjnej. Przestawiono opisową i formalną interpretację pojęcia systemu diagnozującego (SDG). Zaproponowano modele procesu diagnozowania urządzeń...
-
Present state of sewage and wastewater treatment plants in the polish coast of Baltic Sea
PublicationIn the paper the state of art of wastewater management in four zones of Polish Baltic Sea coast: the Vistula Lagoon, the Bay of Gdansk and Bay of Puck, the open sea zone and the Szczecin Lagoon, is discussed. Hydrological characteristics of these four zones as well as characteristics and operation effectiveness of wastewater treatment plants (WWTPs) located there, are presented.
-
Nonreciprocal Devices Utilizing Longitudinally Magnetized Ferrite Coupled Lines
PublicationThis chapter presents authors’ recent research on the nonreciprocal devices utilizing longitudinally magnetized ferrite coupled line (FCL) junction. The principle of operation of FCL junction is explained and the hybrid techniques of analysis are shown. Numerical and experimental results concerning the nonreciprocal devices utilizing the different configurations of FCL junctions are presented and discussed.
-
Modern control strategy of bidirectional DAB converter with consideration of control nonlinearity
PublicationThis paper focuses on the control strategy for modern universal bidirectional Dual Active Bridge (DAB) converters for microgrid systems. An analysis of the converter equations was carried out, and typical problems related to the influence of dead time on the system operation were discussed. A closed control loop was developed, then tested by simulation and on a laboratory stand.
-
Sliding burnishing technology of holes in hardened steel
PublicationNew technology with sliding burnishing of holes with cylindrical surface, made of hardened steel /60 HRC/, is presented in the paper.After burnishing operation on hole diameter 30 mm in satellite gear wheel the surface roughness parameter Ra=0,02-0,04 micrometers was obtained. The method and results of research as technological conclusion are presented.
-
Expert systems in assessing the construction process safety taking account of the risk of disturbances
PublicationThe objective of the paper is to present the issue of safety manage-ment during the construction process. Threats in the form of disturb-ances may occur in the preparatory phase, during the execution of the construction project and also during its operational use. The arti-cle presents the concept of applying the methodology based, among others, on Learning Bayesian Networks, Artificial Neural Networks and Support Vector Machine,...
-
A current-controlled FET
PublicationA novel semiconductor device, viz., Horizontally-Split-Drain Current-Controlled Field-Effect Transistor (HSDCCFET) with two control electrodes is proposed in this works. For the sake of brevity, the device can be called a CCFET. Operating principle of the proposed transistor is based on one of the galvanomagnetic phenomena, the Biot-Savart-Laplace law and a Gradual Channel Detachment Effect (GCDE). The transistor is dedicated...
-
Influence of lubricating oil improvers on performance of crankshaft seals
PublicationThis paper presents an original method for checking influence of lubricating oil improvers on performance of crankshaft seals of combustion piston engine. Crankshaft seals were tested with the use of a modified friction node of T-02 four- ball apparatus in laboratory conditions. The tests were conducted according to a worked-out algorithm. Their results confirmed usefulness of the method for determining „harmful” performance...
-
Model of Rules for IT Organization Evolution
PublicationThe aim of this paper is to introduce the Model of Rules for IT Organization Evolution which shall be in compliance with the Generic IT Organization Evolution Model. Due to its general nature, a set of practical adjustments is proposed in order to adapt the Generic Model to the IT Service Management domain. Further, two sets of rules describing the evolution of the IT Service Management area are defined based on two types of rules...
-
Business applications of geolocation - modern solutions and trends
PublicationThe technological development of geolocation systems has resulted in the utilization of physical location of users by a growing number of entrepreneurs. As mobile technology develops, the use of geolocation in business is becoming widespread with a new range of geomarketing techniques. Entrepreneurs therefore more often utilize geolocation in their promotional and operational activities. In this article mobile-based geolocation...
-
Bulk linearized CMOS differential pair transconductor for continuous-time OTA-C filter design
PublicationIn this paper, the MOS differential pair driven simultaneously from gates and bulk terminals is described. An approximated analytical solution of the voltage to current transfer function has been found for the proposed circuit. Four possible combinations of gate and bulk connections of the input signal are presented. Basing on the configuration giving the best linearity, the operational transconductance amplifier (OTA) has been designed...
-
INTEGRATED FUNCTIONAL SAFETY AND CYBERSECURITY ANALYSIS METHOD FOR SMART MANUFACTURING SYSTEMS
PublicationThis article addresses integrated functional safety and cybersecurity analysis with regard to: the generic functional safety standard IEC 61508 and the cyber security standard IEC 62443 concerning an industrial automation and control system (IACS). The objective is to mitigate the vulnerability of information technology (IT) and operational technology (OT) systems, and reduce relevant risks taking into account a set of fundamental...
-
Fault Loop Impedance Measurement in Circuits Fed by UPS and Principle of Safety Protection
PublicationThis paper indicates a significant problem of uncertainty of fault loop impedance (FLI) measurement in circuits powered from uninterruptible power supply (UPS) (double-conversion AC-DC-AC). The correctly determined value of this impedance, related to the short-circuit current disconnection time and to the reference value, is one of the most important elements that determines the approval of an electrical installation and its receivers...
-
Influence of Natural Conditions on the Imaging of the Bottom of the Gdańsk Bay by Means of the Side Scan Sonar
PublicationThe interest in underwater resources is the reason for the development of modern hydroacoustic systems, including side sonars, which find numerous applications such as: research of seabed morphology and sediment characteristics, preparation of sea sediment maps, and even in special cases of biocenoses such as sea grass meadows, detection of specific targets at the bottom such as shipwrecks, mines, identification of suitable sites...