Filters
total: 3853
displaying 1000 best results Help
Search results for: surowce odtwarzalne
-
Multicomponent layers for aluminium alloys surface consolidation
PublicationThe main reason of the surface modification of the components such as pistons and cylinder blocks made of cast aluminium alloys is to obtain high hardness, wear and corrosion resistance of the working surface for larger lifetime of the motor-car and aircraft engines. In that aspect, the new conception of development - by hybrid method - of surface layers containing manganese, nitrogen, sulphur (Mn-N-S) and manganese, nitrogen,...
-
The Laser Surface Remelting of Austenitic Stainless Steel
Publication -
The evaluation of the surface quality after laser cutting
Publication -
PERS - QUIET ROAD SURFACE FOR URBAN AREAS
PublicationTraffic noise is one of the most important environmental problems in densely populated urban areas. At low speeds the tyre/road interaction dominates all other sources. It is anticipated that when electric and hybrid vehicles gain dominance in city traffic, the importance of tyre/road noise will still increase as electric engines are much less noisy than combustion engines. On the other hand, electric and hybrid urban vehicles...
-
Problems of flat surface lapping : chapter 16
PublicationPrzedstawiono problemy docierania powierzchni płaskich w układach jednotarczowych. Omówiono analityczne i numeryczne modele kinematyki docierarek konwencjonalnych i niestandardowych, obróbkę docierakami aktywizowanymi w sposób swobodny i wymuszony, jednolitymi i dwumetalowymi. Zaprezentowano wyniki obróbki narzędziami ścierno-metalowymi elementów ceramicznych.
-
Surface Dielectric Barrier Discharge Plasma Actuators
PublicationThis paper presents a part of the works conducted in the Plasmaero European project (task 1.1) on surface dielectric barrier discharge actuators applied to airflow control. The study is divided into several parts. In the first part, the goal is to enhance the electric wind produced by a typical single DBD actuator by optimization of the active electrode shape. For instance, the use of a thin wire instead of a plate air-exposed...
-
Effect of surface modification on starch biopolymer wettability
Publication -
Effect of surface modification on starch/phospholipid wettability
Publication -
Hydrothermal Surface Treatment of Biodegradable Mg-Materials
Publication -
Body surface area formulae: an alarming ambiguity
PublicationBody surface area (BSA) plays a key role in several medical fields, including cancer chemotherapy, transplantology, burn treatment and toxicology. BSA is often a major factor in the determination of the course of treatment and drug dosage. A series of formulae to simplify the process have been developed. Because easy-to-identify, yet general, body coefficient results of those formulae vary considerably, the question arises as to...
-
Influence of dissolved organic nitrogen on surface waters
PublicationThe aim of this study was to determine the susceptibility of dissolved organic nitrogen (DON) contained in biologically treated wastewater disposed from municipal wastewater treatment plants (WWTPs) to biodegradability and bioavailability in a water environment. Additionally an evaluation was performed of the participation of this organic nitrogen fraction, including bioavailable DON (bDON), in the nitrogen balance for the Baltic...
-
Economical methods for measuring road surface roughness
PublicationTwo low-cost methods of estimating the road surface condition are presented in the paper, the first one based on the use of accelerometers and the other on the analysis of images acquired from cameras installed in a vehicle. In the first method, miniature positioning and accelerometer sensors are used for evaluation of the road surface roughness. The device designed for installation in vehicles is composed of a GPS receiver and...
-
Singular Surface Curves in the Resultant Thermodynamics of Shells
PublicationWithin six-parameter shells theory we discuss the governing equations of shells with material or non-material singular curves. By singular curve we mean a surface curve where are discontinuities in some surface fields. As an example we consider shells with junctions and shells undergoing stress-induced phase transitions.
-
Shaping of the workpiece surface in single-disc lapping
PublicationShape errors of the tool exert a dominant influence on the shape accuracy of the workpiece. The correlation between flatness errors of the lap and flatness errors of the workpieces was checked experimentally and determined analytically. Computer model of the workpiece shaping by lapping was developed. Evaluation method of the workpiece orientation as well as some simulation results for a lap with shape errors of convexity and cincavity...
-
Comparison of volume-and surface-detention-time distributions
PublicationCzas zatrzymania ścieków w reaktorze jest bardzo ważnym parametrem projektowym. Jego wyznaczenie jest trudne i kłopotliwe. Z tego względu zbadano możliwość zastąpienia wartości tego parametru, wyznaczonej tylko dla swobodnej powierzchni ścieków. W wyniku stwierdzono dopuszczalność takiej zamiany.
-
Some aspects surface cooling by impinging jet
PublicationW pracy przedstawiono wyniki badań wymiany ciepła, uskoku hydraulicznego i stabilności podczas napływu strugi na powierzchnię ciała stałego.
-
Shaping of the workpiece surface in single-disc lapping
PublicationPrzedstawiono korelację pomiędzy błędami kształtu docieraka i błędami kształtu przedmiotów obrabianych. Wyniki analityczne zostały sprawdzone doświadczalnie, co pozwoliło zbudować komputerowy model kształtowania powierzchni docieranych. Przedstawiono sposób wyznaczania intensywności kontaktu między przedmiotem docieranym, a docierakiem. Opracowano metodę wyznaczania położenia przedmiotu na docieraku.
-
Probabilistic analysis of slope with planar slip surface
PublicationPraca dotyczy probabilistycznej oceny stateczności zboczy. Omówiono sposób określania prawdopodobieństwa utraty stateczności przy wykorzystaniu metody momentów (ang. FOSM). Podejście takie zastosowano do analizy zsuwu konsekwentnego jednorodnego zbocza. Rozpatrzono wpływ zmienności statystycznej parametrów wytrzymałościowych na końcowe wyniki.
-
Formation of wood surface roughness in burnishing process
PublicationW publikacji przedstawiono i omówiono rozwój bezwiórowych metod obróbki wykańczającej drewna przez nagniatanie. Przedstawiono wpływ nagniatania na chropowatość powierzchni drewna. Badania przeprowadzono na próbkach toczonych i nagniatanych. Wyniki odniesiono do głównych parametrów nagniatania jak: siła nagniatania oraz promień zaokrąglenia elementu nagniatającego.
-
Janusz Datta prof. dr hab. inż.
PeopleIn 1988, Janusz Datta finished his studies at the Gdańsk University of Technology (GUT), Faculty of Chemistry. Since then he has been employed at the Faculty of Chemistry in the Department of Polymer Technology. During the first six years of employement he was worked as a scientist. In this period, he travelled extensively to ZACHEM company located in Bydgoszcz to gain practical experience related to chemical processing. In 1994,...
-
Surface diffusion and cluster formation of gold on the silicon (111)
PublicationPurpose: Investigation of the gold atoms behaviour on the surface of silicon by molecular dynamics simulation method. The studies were performed for the case of one, two and four atoms, as well as incomplete and complete filling of gold atoms on the silicon surface. Design/methodology/approach: Investigations were performed by the method of molecular dynamics simulation using the Large-scale Atomic/Molecular Massively Parallel...
-
A device for measuring heat flux on a rocket skin surface
PublicationA novel method for measuring heat flux on a surface is presented. It is an extensive upgrade of currently known heat flux sensors used mostly in civil engineering. As the thermal environment of launchers, especially sounding rocket can have an enormous negative effect on payload, careful considerations have to be taken in the process of preparing insulation. Usually, thermal data provided by the launch vehicle manufacturer is limited...
-
Measurement of temperature at sliding polymer surface by grindable thermocouples
PublicationThis paper is devoted to experimental study of capabilities and limitations of grindable thermocouples as applied to polymer materials sliding on metal. Chromel–alumel and chromel–copel grindable thermocouples have been developed and tested for wide ranges of contact pressure and sliding velocity. The background temperature of the sliding surface can be determined as the lower envelope of the signal from the grindable thermocouple....
-
3D Metamaterial Ultra-Wideband Absorber for curved surface
PublicationThis paper proposes a three-dimensional metamaterial absorber based on a resistive film patch array to develop a low-cost, lightweight absorber for curved surfaces. An excellent absorption over a large frequency band is achieved through two different yet controllable mechanisms; In the first mechanism, a considerable attenuation in the wave power is achieved via graphite resistive films. The absorption is then intensified through...
-
Detection of Water on Road Surface with Acoustic Vector Sensor
PublicationThis paper presents a new approach to detecting the presence of water on a road surface, employing an acoustic vector sensor. The proposed method is based on sound intensity analysis in the frequency domain. Acoustic events, representing road vehicles, are detected in the sound intensity signals. The direction of the incoming sound is calculated for the individual spectral components of the intensity signal, and the components...
-
Surface Texture after Turning for Various Workpiece Rigidities
PublicationIn the paper, we present an analysis of the surface texture of turned parts with L/D (length/diameter) ratios of 6 and 12 and various rigidity values. The studies were carried out on samples made of S355JR steel and AISI 304 stainless steel. A detailed analysis of 2D surface profiles was carried out by using a large number of parameters that allowed us to distinguish significant differences in the surface microgeometry, which confirmed...
-
How important are scaffolds and their surface properties in regenerative medicine
Publication -
Post-plasma oxidation in water of graphene paper surface
Publication -
Surface Roughness Model Components Created by Stereolithography Method
PublicationW pracy przedstawiono charakterystykę powierzchni elementów wykonywanych metodą stereolitografii. Opisano modele chropowatosci stosowane do opisywania powierzcni wraz z prezentacją formuł matematycznych. W oparciu o wyniki badań eksperymentalnych przeprowadzono częściową weryfikację modeli.
-
Distribution of roughness and waviness components of turned surface profiles
PublicationThe paper presents a spectral formulation of surface profile irregularity in a wideband frequency range for roughness, waviness and shape components along the measured length. A unique distribution of roughness and waviness components is proposed, according to the nature of their origination in the course of machining with tools of defined cutting edge, as distinct from standard filtration in measurements of surface irregularities....
-
New laser-enhanced surface treatment of Ti bioalloy
PublicationPrzedstawiono wyniki badan mikrostruktury i korozji w roztworze Ringera stopu Ti6Al4V, który był poddawany nadtapianiu laserem CO2 w powietrzu, wodzie i ciekłym azocie. Stwierdzono znaczący wpływ warunków obróbki na mikrostrukturę, mikrotwardość i głębokość zmodyfikowanej warstwy wierzchniej.
-
An effective Hamiltonian for sulfur adsorption at Au(100) surface
Publication -
Distribution and bioavailability of mercury in the surface sediments of the Baltic Sea
PublicationThe study aimed to determine the level of mercury (Hg) and its labile and stable forms in the surface sediments of the Baltic Sea. The work considers the impact of current and historical sources of Hg on sediment pollution, together with the influence of different environmental parameters, including water inflows from the North Sea. Surface sediments (top 5 cm) were collected in 2016–2017 at 91 stations located in different...
-
Entropy analysis of surface EMG for classification of face movements
Publication -
Profile and Areal Surface Parameters for Fatigue Fracture Characterisation
Publication -
Surface treatment of porous Ti13Nb13Zr alloy for biomedical applications
PublicationPrzeprowadzono badania materiału porowatego, przeznaczonego na implanty ortopedyczne, wytworzonego metodą metalurgii proszków ze stopu Ti13Nb13Zr. Proszki z badanego stopu uzyskano metodą rozpylania plazmowego. Otrzymano próbki o otwartej porowatej strukturze, stopniu porowatości do 68% i średniej wielkości porów w przedziale 30-150 mikrometrów. Obróbka próbek porowatych - utlenianie termiczne, chemiczne i/lub elektrochemiczne...
-
Antagonist adhesion effects due to variable substrate surface
PublicationThe effects of variability of intrinsic adhesion within a joint have been studied using a single cantilever beam (SCB) test. Fracture energy was found not to be a simple function of relative areas of 2 surface pre-treatments: a 'weak' zone decreased strength more than expected from simple, additive considerations. By severing the adhesive along the strong-weak transition, fracture energy increased.The prior antagonist effect appears...
-
Estimation of wear of electroplated tools used for surface grinding
PublicationW pracy dokonano ilościowej oceny zużycia narzędzi galwanicznych diamentowych i borazonowych. Wykorzystano analizę jasności obrazów narzędzi oraz badano liczność ziaren ściernych na czynnej powierzchni narzędzia.
-
Surface roughness chracteristic if components created by stereolithography method
PublicationModele wykonywane metodami szybkiego prototypowania mają charakterystyczna strukturę powierzchni określaną mianem schodkowatości. W artykule przedstawiono modele obliczeniowe profilu nierówności jak i porównanie ich z wynikami pomiarów
-
Charakterystyka białek głównych surowców żywnościowych. Rozdział 6
PublicationBiałka mięśniowe mają w większości bardzo korzystny skład aminokwasowy i pożądane właściwości funkcjonalne. Są to białka cieczy międzykomórkowej i sarkoplazmy, białka włókien mięśniowych - przede wszystkim miozyna i aktyna, a także kolageny i elastyna. Wśród białek mleka największy udział mają kazeiny, uczestniczące w tworzeniu skrzepu w serowarstwie, zaś w serwatce są głównie β-laktoglobulina, α-laktoalbumina, immunoglobuliny,...
-
Design of Ground Surface Sealing in The Spatial Policy of Communes
Publication -
The Effect of Spikes Occurrence on Surface Texture Parameter Assessments
Publication -
Treated wasetewater as a source of humic substances in surface waters
PublicationHumic substances impose substantial effect on the aquatic environment as well as the water organisms and human health. Among other features, the humic acids determine organoleptic properties of surface waters. Therefore explanation of the origin and properties of humic acids in surface waters is one of the priorities of water technology.Recently it was pointed out that in the wastewater treatment process organic compounds characterized...
-
Unusual interfacial phenomena at a surface of fullerite and carbon nanotubes
Publication -
The corrosion resistance of laser surface alloyed stainless steels
Publication -
Fermentacje w przetwarzaniu mięsa i surowców roślinnych
PublicationW rozdziale przedstawiono charakterystykę fermentowanych produktów mięsnych i rybnych oraz omówiono czynniki wpływające na ich jakość. Przedstawiono procesy zachodzące podczas fermentacyjnego przetwarzania surowców roślinnych. Opisano produkcję kiszonek paszowych.
-
Computer Supported Analysis of the Human Body Surface Area
PublicationRecent scientific studies show the growing importance of the coefficients: BSA and TBSA, as an alternative to the widely used BMI. The relevant indicators are widely used in medicine, including such areas as: the treatment of burns, chemotherapy, dermatology and toxicology; as benchmarks when calculating doses of drugs and fluids. The particular problems concerning this subject are: the change of the reference parameter value which...
-
Microstructure and residual stresses in surface coatings with PTFE reservoirs
PublicationThe paper presents the results of experimental study into the microstructure and changes in residual stresses resulting from sliding and rolling/sliding loaded interaction between metallic surface coatings with embedded PTFE reservoirs and various counter faces. It was found that before testing surface coatings had compressive residual stresses. Molybdenum coating with all types of PTFE reservoirs displayed, as a result of testing,...
-
Some aspects of laser surface remelting of aluminium alloys
PublicationPodano podstawy procesu przetapiania laserowego stopów aluminium. Opisano rezultaty elektrochemicznych badań korozyjnych dla stopu AlSi13Mg1CuNi i porównano je ze stanem wyjściowym stopu.
-
Surface layer defects on injection-molded plastic components
PublicationProces wtryskiwania jakkolwiek jest powszechnie stosowany w przemyśle nie jest jeszcze do końca przebadany. W pracy przedstawiono model i symulację numeryczna procesu wtryskiwania wykonaną na bazie programu FIDAP. Na tej podstawie przedstawiono proces zachowania się tworzywa podczas procesu wtryskiwania w strefie przyściennej formy. Wyniki z symulacji porównano z danymi ekspermentalnymi.