Filtry
wszystkich: 3111
wybranych: 1248
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: cyclic%20voltammetry
-
Carbon dioxide sequestration by industrial wastes through mineral carbonation: Current status and perspectives
PublikacjaMineral carbonation using natural minerals or industrial wastes is a safe and promising strategy for CO2 sequestration. Application of industrial wastes for this purpose has significant ecological and environmental value, which is one of the key green technologies in the global carbon mitigation. This review summarizes the current research status of CO2 mineralization by industrial wastes. This work surveys the mechanisms and capacities...
-
Analysis of the Possibility of Using New Types of Protective Coatings and Abrasion-Resistant Linings under the Operating Conditions of the Spiral Classifier at KGHM Polska Miedź S.A. Ore Concentration Plant
PublikacjaA study was carried out to select the appropriate coatings for corrosion protection of the spiral classifier working at KGHM Polska Miedź S.A. Ore Concentration Plant. The abrasion resistance of selected protective coatings and wear-resistant linings was investigated using a DT-523 rotary abrasion tester with Taber CS-10 rubber abrasive discs. The average weight loss of the coatings after a cycle of 2000 revolutions was determined....
-
Self-healing mechanism of metallopolymers investigated by QM/MM simulations and Raman spectroscopy
PublikacjaThe thermally induced self-healing mechanisms in metallopolymers based on bisterpyridine complexes of iron(II) sulfate and cadmium(II) bromide, respectively, were studied by means of combined quantum mechanical/molecular mechanical (QM/MM) simulations and Raman spectroscopy. Two possible healing schemes, one based on a decomplexation of the cross-linking complexes and a second one relying on the dissociation of ionic clusters,...
-
Utilisation of waste heat from the power plant by use of the ORC aided with bleed steam and extra source of heat
PublikacjaUtilization of waste heat recovered from the exhaust gases of the power generation unit by means of ORC (organic Rankine cycles) installation is considered. The waste heat is available in the form of a stream of hot water having temperature of 90 stC in the amount of 200 MWt. To increase evaporation temperaturę of ORC working fluid the heat of steam from the extraction points from the low-pressure part of steam turbine is used....
-
Studies on the Combined Impact of Starch Source and Multiple Processing on Selected Properties of Thermoplastic Starch/Ethylene-Vinyl Acetate Blends
PublikacjaThermoplastic starch (TPS)/ethylene vinyl acetate (EVA) blends compatibilized with polyethylene-graft-maleic anhydride (PE-g-MA) were prepared from various native starches (potato, maize and waxy maize) and subjected to multiple extrusion cycles. Source of starch has significant impact on its composition, hence properties of obtained TPS and their blends with EVA. Higher content of amylopectin in waxy maize starch, comparing to...
-
New ceramic materials derived from pyrolyzed poly(1,2-dimethylsilazane) and starch as a potential anode for Li-ion batteries
PublikacjaNewmaterialswere obtained by pyrolysis of starch (S) and poly(1,2-dimethylsilazane) (PSN) (weight ratio: PSN/S 30/70) at temperature a) 500 °C, b) 700 °C and c) 900 °C. Ceramic materials were characterized by infrared spectroscopy, TGA, Raman spectroscopy and SEM. New Si\O and shifted Si\C stretching vibration modes emerged confirming direct interaction between silicon originating fromsilazane and oxygen coming fromstarch. The...
-
Is the Solid Electrolyte Interphase an Extra-Charge Reservoir in Li-Ion Batteries?
PublikacjaAdvanced metal oxide electrodes in Li-ion batteries usually show reversible capacities exceeding the theoretically expected ones. Despite many studies and tentative interpretations, the origin of this extra-capacity is not assessed yet. Lithium storage can be increased through different chemical processes developing in the electrodes during charging cycles. The solid electrolyte interface (SEI), formed already during the first...
-
Preparation and characterization of asphaltene based adsorbents for gas-solid adsorption systems
PublikacjaThe dissertation presents results of the experimental research on asphaltene-based adsorbents (support coated with asphaltene layer) for gas-solid adsorption systems, with special reference to volatile organic compounds (VOCs) removal from gas streams. Analysis of gas adsorption properties revealed that asphaltenes isolated from oxidized bitumen have strong affinity toward VOCs. Interactions with target gas molecules, and selectivity...
-
Analytical chemistry in technical approaches: immobilization of biosorbent waste containing heavy metals in cemented materials
PublikacjaAn ecologically safe and economically justified method of stabilization of the used biosorbents was developed. Sorbent contaminated with heavy metals has been successfully solidified/stabilized using a hydraulic binder. The test results indicated that up to 1% of the biosorbent residue used could be added without compromising the compressive strength of the mortar. The compressive strength of the modified mortars did not change...
-
Assembling and testing of quasi-static hybrid piezoelectric motor based on electroactive lubrication principle
PublikacjaThe presented paper concerns a novel concept of hybrid piezoelectric motor based on electroactive lubrication principle. Its structure is combined of quasi-static and resonance piezoelectric actuators, synchronizing their work to generate the rotary movement. The hybrid motor topology is compared to the existing piezoelectric motors, regarding its field of applications in embedded systems with very high security requirements. The...
-
Design and distribution of air nozzles in the biomass boiler assembly
PublikacjaDue to energy crisis as well as increasing pollution of the environment, renewable energy sources usage increases all over the world. These facts encouraged authors to start research over developing a uniform biomass boiler calculation model. This paper presents a design of biomass boiler assembly created for ORC (Organic Rankine Cycle) unit since these systems could achieve strong position in energy industry....
-
Warstwowy system zabezpieczeń w przemysłowych instalacjach podwyższonego ryzyka
PublikacjaRozdział poświęcono aktualnym zagadnieniom analizy i projektowania warstw zabezpieczeń w kontekście oceny ryzyka i zarządzania bezpieczeństwem funkcjonalnym w cyklu życia z wyróżnieniem trzech warstw: (1) podstawowego systemu sterowania BPCS (basic process control system), (2) człowieka-operatora korzystającego opcjonalnie z systemu alarmowego AS (alarm system) oraz (3) przyrządowego systemu bezpieczeństwa SIS (safety instrumented...
-
Development of chromatographic and mass spectrometry conditions for untargeted lipidomic analysis of human breast milk
PublikacjaHuman breast milk (HBM) is a complex biofluid containing components which are essential for the proper growth of the newborn (for example nutrients such as carbohydrates, proteins, lipids) and also bioactive substances. According to the literature, most of studies involving HBM nutrients investigations focused essentially on the determination of proteins. The molecular composition of lipids in HBM is not well known as the protein...
-
Implementing Smart Virtual Product Development (SVPD) to Support Product Manufacturing
PublikacjaThis paper illustrates the concept of providing the manufacturing knowledge during early stages of product life cycle to experts working on product development. The aim of this research is to enable a more collaborative product development environment by using Smart Virtual Product Development (SVPD) system, which is powered by Set of Experience Knowledge Structure (SOEKS) and Decisional DNA (DDNA). It enhances the industrial product...
-
Smart experience engineering to support collaborative design problems based on constraints modelling
PublikacjaEngineering design is a knowledge intensive process. Experts' experiences from different product life-cycle stages play a key role in problem solving during design decision making by linking up knowledge to find better solutions for a specific design problem. Different approaches have been used to support Collaborative and Concurrent Product Design, such as Constraint Satisfaction Problem (CSP) modelling. Additionally, due to the...
-
The Comparison of the Crypto- and Fiat Currencies’ Exchange Rate Volatility in The Years 2015–2017
PublikacjaThe article describes the issues related to exchange rate volatility of crypto- and fiat currencies. The first part presents the issue of exchange rate volatility as well as methods of its evaluation and criteria of the conducted research. In the next part the author presented the essence of currencies and the main currency i.e. fiat money in the global economy in terms of the volume of transactions on the FOREX market. Then the...
-
Influence of reactive oxygen species during deposition of iron oxide films by high power impulse magnetron sputtering.
PublikacjaIron oxide films were deposited using high power impulse magnetron sputtering (HiPIMS) of an iron cathode in an argon/oxygen gas mixture at different gas pressures (0.5~Pa, 1.5~Pa, and 5.0~Pa). The HiPIMS system was operated at a repetition frequency $f = 100$~Hz with a duty cycle of 1~\%. A main goal is a comparison of film growth during conventional and electron cyclotron wave resonance-assisted HiPIMS. The deposition plasma...
-
HIGH TEMPERATURE HEAT PUMPS – PERSPECTIVE HEATING SYSTEMS?
PublikacjaIn the paper presented are authors own concepts of high temperature compressor heat pumps for the utilisation of medium and low temperature sources of heat. Working fluids for use in high temperature heat pumps are discussed, as well as the criteria for their selection. Analyses are presented for the production of in the upper steam source at 130 °C. One-stage systems and cascade systems were analyzed. An analysis of the coefficient...
-
Evaluating the performance of organic coatings under mechanical stress using electrochemical impedance spectroscopy
PublikacjaMimo, iż znaczna liczba konstrukcji zabezpieczanych przy pomocy powłok poddawana jest cyklicznym naprężeniom mechanicznym, czynnik ten wydaje się być niedoceniany jako przyczyniający się do przyspieszonego niszczenia organicznych układów powłokowych. Celem pracy było zweryfikowanie czy powtarzające się naprężenia mechaniczne stanowią istotny element wpływający na skrócenie czasu eksploatacji systemów powłokowych. W tym celu układ:...
-
Adoption of the F-statistic of Fisher-Snedecor distribution to analyze importance of impact of modifications of injector opening pressure of a compression ignition engine on specific enthalpy value of exhaust gas flow
PublikacjaThis article analyzes the effect of modifications of injector opening pressure on the operating values of a compression ignition engine, including the temperature of the fumes. A program of experimental investigation is described, considering the available test stand and measurement capabilities. The structure of the test stand on which the experimental measurements were conducted is presented. The method of introducing real modifications...
-
Organic syntheses greenness assessment with multicriteria decision analysis
PublikacjaGreen chemistry requires a metrics system that is comprehensive by the criteria included and simple in the application at the same time. We propose the application of multicriteria decision analysis for com- parative greenness assessment of organic synthesis procedures. The assessment is based on 9 criteria (the reagent, reaction efficiency, atom economy, temperature, pressure, synthesis time, solvent, catalyst and reactant) for...
-
Multiaxial Fatigue Behaviour of SLM 18Ni300 Steel
PublikacjaFatigue behaviour of SLM 18Ni300 steel under proportional bending-torsion loading is studied. The fatigue tests are conducted under pulsating loading conditions using tubular specimens with a transversal circular hole. Three ratios of the normal stress to shear stress are considered, namely σ/τ=4,σ/τ=2 and σ/τ = 4/3. Crack initiation sites were found for two diametrically opposite points around the hole, whose locations are governed...
-
On the production of electricity in Poland using a geothermal binary power plant - A thermodynamic overview - Part I
PublikacjaPoland has a significant potential of geothermal energy. However, the high-temperature sources that are needed to drive power plants are found in relatively few places. Therefore, the objective of this paper is to consider any location in the northern part of Poland as a possible place to build a binary power plant. A scientific research was confirmed the existence of an elevated temperature gradient in this region. The hot rocks...
-
Characterization of glucoamylase immobilized on magnetic nanoparticles
PublikacjaMagnetic support was prepared by precipitation from an alkaline solution of divalent and trivalent iron ions and subsequently was modified with 3-aminopropyltriethoxysilane. FTIR analysis showed existence of a new Si-O-Fe bond in obtained particles. Scanning electronic microscopy images shows that the nanoparticles of all samples have particle size below 30 nm. Glucoamylase AMG 300L was immobilized onto the modified magnetic support...
-
Structure and Molecular Dynamics in Renewable Polyamides from Dideoxy-Diamino Isohexide
PublikacjaThe chemical structure, the conformation, andthe flexibility of the polymer chain fragments present in thepolyamides synthesized from 2,5-diamino-2,5-dideoxy-1,4;3,6-dianhydrosorbitol, 1,4-diaminobutane, and either sebacic orbrassylic acid have been studied by liquid-state 2D NMRspectroscopy viz. correlation spectra (COSY) and heteronuclearmultiple-bond correlation spectra (gHMBC), by 13Ccross-polarization/magic-angle spinning...
-
The role of EMG module in hybrid interface of prosthetic arm
PublikacjaNearly 10% of all upper limb amputations concern the whole arm. It affects the mobility and reduces the productivity of such a person. These two factors can be restored by using prosthetics. However, the complexity of human arm makes restoring its basic functions quite difficult. When the osseointegration and/or targeted muscle reinnervation (TMR) are not possible, different modalities can be used to control the prosthesis. In...
-
T-colorings, divisibility and circular chromatic number
PublikacjaLet T be a T-set, i.e., a finite set of nonnegative integers satisfying 0 ∈ T, and G be a graph. In the paper we study relations between the T-edge spans espT (G) and espd⊙T (G), where d is a positive integer and d ⊙ T = {0 ≤ t ≤ d (max T + 1): d |t ⇒ t/d ∈ T} . We show that espd⊙T (G) = d espT (G) − r, where r, 0 ≤ r ≤ d − 1, is an integer that depends on T and G. Next we focus on the case T = {0} and show that espd⊙{0} (G) =...
-
Comparison of Ozonation and Evaporation as Treatment Methods of Recycled Water for Bioethanol Fermentation Process
PublikacjaThe paper compared the performance of the ethanol yield after alcoholic fermentation with samples of rejected (RW) and permeate water (PW), RW and PW treated by oxidation with ozone (O3) (5 and 15 min) and evaporation, aiming the recirculation back to the bioethanol process. RW and PW were collected after an anaerobic bioreactor (AnBR) used for stillage treatment. Nine types of fermentations were made, where one used 100% tap...
-
Mechanical-Level Hardware-In-The-Loop and Simulation in Validation Testing of Prototype Tower Crane Drives
PublikacjaIn this paper, the static and dynamic simulations, and mechanical-level Hardware-In-the-Loop (MHIL) laboratory testing methodology of prototype drive systems with energy-saving permanent-magnet electric motors, intended for use in modern construction cranes is proposed and described. This research was aimed at designing and constructing a new type of tower crane by Krupiński Cranes Company. The described research stage was necessary...
-
β-cyclodextrin-containing polymer based on renewable cellulose resources for effective removal of ionic and non-ionic toxic organic pollutants from water
PublikacjaA novel, bio-derived cyclodextrin-based trifunctional adsorbent has been successfully synthesized for efficient, rapid and simultaneous removal of a broad-spectrum of toxic ionic (anionic and cationic dyes) and non-ionic organic pollutants from water. The composition, morphology and the presence of functional groups in the obtained sorption material were characterized by elemental analysis, XRD, SEM, and FTIR spectroscopy. The...
-
Deep eutectic solvents – based green absorbents for effective volatile organochlorine compounds removal from biogas
PublikacjaVolatile organochlorine compounds (VOXs) presented in biogas can cause many technological and environmental problems. During the combustion of biogas containing VOXs, the corrosion of installation, as well as the formation of toxic by-products (polyhalogenated dioxins and furans) and further emission to the atmosphere, may occur. Therefore, in this study, a new procedure based on physical absorption was developed. In order to meet...
-
Band Gap Engineering toward Semimetallic Character of Quinone-Rich Polydopamine
PublikacjaSemiconductor|melanin interfaces have received increasingly more attention in the fields of photocatalysis and applied electrochemistry because of their facile synthesis, unique electrical properties, and strong capability toward photosensitization. In this work, we describe the electropolymerization of quinone-rich polydopamine (PDA) on the surface of hydrogenated TiO2 nanotubes with enhanced photoactivity in the visible spectrum....
-
Experimental investigation on heat pipes supported by soy wax and lauric acid for electronics cooling
PublikacjaThis paper presents an experimental study of heat pipes for electronics cooling that were supported by energy storage materials (i.e. phase change materials - PCMs) coated at the adiabatic section. The PCMs utilized included two materials, namely lauric acid and soy wax, the latter being considered as a more cost-effective alternative. The study focused on three different powers: 20 W, 25 W, and 30 W. Both heating, cooling, and...
-
Modele ruchu w nowoczesnym zarządzaniu transportem drogowym
PublikacjaWdrożenie i rozwijanie wielopoziomowego modelu podróży i sieci transportowej (MST), w ramach Systemu Planowania Ruchu (SPR), usprawniającego zarządzanie transportem w systemach transportowych z wykorzystaniem usług oferowanych przez Inteligentne Systemy Transportu, może stanowić wsparcie naukowe dla krajowych, regionalnych lub lokalnych administracyjnych jednostek planistycznych i operacyjnych w usprawnieniu systemowego zarządzania...
-
Effects of UV light irradiation on fluctuation enhanced gas sensing by carbon nanotube networks
PublikacjaThe exceptionally large active surface-to-volume ratio of carbon nanotubes makes it an appealing candidate for gas sensing applications. Here, we studied the DC and low-frequency noise characteristics of a randomly oriented network of carbon nanotubes under NO2 gas atmosphere at two different wavelengths of the UV light-emitting diodes. The UV irradiation allowed to sense lower concentrations of NO2 (at least 1 ppm) compared to...
-
Synthesis and Characterization of Poly(zwitterionic) Structures for Energy Conversion and Storage
PublikacjaZwitterions are unique class of molecules that possess two functional groups bearing electric charges, one positive and second negative. This setup results in peculiar properties such as high water retention and anti-fouling capability. Therefore, zwitterionic coatings and gels are commonly applied in e.g. biosensing and bioelectronic devices. Despite those applications, there are other perspectives for zwitterionic materials....
-
Combined cold supply system for ship application based on low GWP refrigerants - Thermo-economic and ecological analyses
PublikacjaThe withdrawal of popular high-GWP refrigerants will significantly affect maritime industry. Refrigeration and air conditioning systems currently used on ships are not ready to fulfil future limitations. Therefore, there is a need for system, which will operate with low-GWP refrigerants and at the same time will be efficient and reliable in difficult environmental conditions. This paper explains the concept of a cold supply system,...
-
DESIGN ANALYSIS OF HYBRID GAS TURBINE - FUEL CELL POWER PLANT IN STATIONARY AND MARINE APPLICATIONS
PublikacjaThe paper concerns design analysis of a hybrid gas turbine power plant with a fuel cell (stack). The aim of this work was to find the most favorable variant of the medium capacity (approximately 50 MW) hybrid system. In the article, computational analysis of two variants of such a system was carried out. The analysis let to calculate capacity, efficiency of both variants and other parameters like flu gas temperature. The paper...
-
Ultrasound-assisted wet-impregnation of Ag–Co nanoparticles on cellulose nanofibers: Enhanced catalytic hydrogenation of 4-nitrophenol
PublikacjaIn this study, a novel nanocomposite of bimetallic Ag–Co nanoparticles supported on cellulose nanofibers (CNFs) was synthesised using the ultrasound-assisted wet-impregnation method for catalytic applications. CNFs were prepared from cellulose acetate using the electrospinning technique. Fourier transform infrared spectroscopy (FTIR) analysis confirmed the successful synthesis of CNFs. Further, scanning electron microscopy (SEM)...
-
Wybrane zagadnienia optymalizacji organizacji ruchu kolejowego w celu minimalizacji kosztów energii elektrycznej
PublikacjaW artykule przedstawiono podział kosztów w transporcie kolejowym z uwzględnieniem kosztów wewnętrznych przedsiębiorstwa, do których zaliczają się między innymi koszty dostępu do infrastruktury, czy koszty energii. Stwierdzono, że przy odpowiedniej organizacji ruchu pociągów na sieci kolejowej, bez ponoszenia dodatkowych nakładów na infrastrukturę i specjalistyczne urządzenia, można znacznie ograniczyć zużycie energii, a co za tym...
-
Laboratorium Proekologicznych Źródeł Energii na Wydziale Chemicznym Politechniki Gdańskiej
PublikacjaMożliwości rozwoju rodzimego przemysłu fotowoltaicznego, mającego w dłuższej perspektywie potencjał na znaczne zwiększenie bezpieczeństwa energetycznego kraju, są ograniczone przez brak krajowego rynku. W tym aspekcie istotna jest działalność Laboratorium Proekologicznych Źródeł Energii, które funkcjonuje na Wydziale Chemicznym Politechniki Gdańskiej w Katedrze Aparatury i Maszynoznawstwa Chemicznego od 1995 roku i służy realizacji...
-
Analiza możliwości odzyskiwania ciepła odpadowego w przemyśle rafineryjnym z wykorzystaniem układów ORC
PublikacjaJednym z najważniejszych zagadnień współczesnej techniki jest poszukiwanie nowych możliwości pozyskiwania energii elektrycznej poprzez zagospodarowanie dotychczas niewykorzystanych lub bezużytecznie marnowanych jej źródeł. Jest to niezwykle ważna kwestia zarówno z ekonomicznego, technologicznego, jak i środowiskowego punktu widzenia. Jednym z przykładów nowoczesnych rozwiązań w tej dziedzinie może być zastosowanie układu opartego...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a microturbine for a cogeneration micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3 kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attentionwas paid...
-
Gazowa mikrosiłownia domowa z modułem ORC - doświadczenia z badania prototypu
PublikacjaArtykuł zawiera rozważania nad ideą wykorzystania obiegu parowego ORC (Organic Rankine Cycle) do skojarzonej produkcji ciepła i energii elektrycznej dla pokrycia potrzeb indywidualnego odbiorcy. Dokonano w nim podsumowania dotychczasowych prac prowadzonych przez Autorów, które zaowocowały budową demonstracyjno-badawczego stanowiska mikro-CHP z technologią ORC w skali „domowej”, współpracującą z komercyjnym kotłem gazowym. W publikacji...
-
The conception of energetic investigations of the multisymptom fatigue of the simple mechanical systems' constructional materials
PublikacjaThe article presents the basic assumptions of the research project aimed, as the main scientific purpose, an identification of the slow-changeable energy processes surrounding the high-cycle fatigue of constructional materials within the plain mechanical system, especially the marine one, for diagnostic purposes. There is foreseen an application of alternative diagnostic methods based on energetic observations of the multi-symptom,...
-
Partial Admission Stages of High Efficiency for a Microturbine
PublikacjaThe paper presents the results of a design analysis of a micro-turbine for a co-generation micro-power plant working in accordance with organic Rankine cycle. The heat power of the plant is assumed equal to 20kW and the corresponding available electric output is estimated to be about 3kW. After the design analysis, the axial turbine with partial admission in all stages was built and tested experimentally. Special attention was...
-
Cooperation of ORC installation with a gas boiler as a perspective co-generation system for households
PublikacjaThis paper reports tests of an innovative micro-CHP unit prototype, consisting of a traditional gas boiler and organic Rankine cycle (ORC), which incorporates original system components such as an axial vapour microturbine, evaporator and condenser. The system co-generates heat and electricity for a single household or a group of households. Electricity is only a by-product during production of heat. While testing the prototype,...
-
Experience-Based Decisional DNA (DDNA) to Support Product Development
PublikacjaKnowledge and experience are important requirements for product development. The aim of this paper is to propose a systematic approach for industrial product development. This approach uses smart knowledge management system comprising of Set of Experience Knowledge Structure and Decisional DNA (DDNA) along with Virtual Engineering Tools (Virtual engineering object, Virtual engineering process, and Virtual engineering factory)....
-
Stale odporne na korozję i ich spawalność
PublikacjaW monografii przedstawiono charakterystykę podstawowych grup stali odpornych na korozję, a zwłaszcza stali nierdzewnych, oraz szczegółowe analizy wpływu cykli cieplnych spawania na strukturę i właściwości złączy w aspekcie spawalności metalurgicznej, technologicznej i konstrukcyjnej stali. Poza analizą dostępnej literatury, w monografii zawarto opis doświadczeń Autora dotyczących badań spawalności stali austenitycznych oraz stali...
-
Heavy duty vehicle fuel consumption modelling using artificial neural networks
PublikacjaIn this paper an artificial neural network (ANN) approach to modelling fuel consumption of heavy duty vehicles is presented. The proposed method uses easy accessible data collected via CAN bus of the truck. As a benchmark a conventional method, which is based on polynomial regression model, is used. The fuel consumption is measured in two different tests, performed by using a unique test bench to apply the load to the engine. Firstly,...