Wyszukiwarka
Filtry
wszystkich: 554
wybranych: 464
-
Katalog
Filtry wybranego katalogu
Wyniki wyszukiwania dla: ROAD MEASUREMENTS
-
Systematics of intelligent transport systems services
PublikacjaRecent years have seen a more intensified deployment of Intelligent Transport Systems (ITS) in Polish cities. Work is also underway on the implementation of ITS on the national roads within the National Traffic Management System (KSZR). The research project RID-4D (part of Road Innovations), is designed to fill the gap, which is the lack of systematics of ITS services in Poland. The paper presents a proposal of ITS services systematics,...
-
Pylon foundation of a cable stayed bridge at the motorway ring road of Wrocław
PublikacjaThe largest bridge of the motorway ring road of Wroclaw is a cable stayed bridge over the Odra river near Rędzin. Due to hydrogeological conditions of the ground it was not convenient to use standard bored piles of high length. Instead shorter piles were applied with additional improvement by cement injections at the pile toes. This decision was possible by extending ground investigation program and application of numerical modeling...
-
Experimental study of the use of electric car powered with stationary solar and electrochemical batteries in Northern Poland
PublikacjaThe subject of this paper is an experimental analysis of a Nissan LEAF electric car equipped with 24 kWh battery, powered from the standalone photo-voltaic (PV) charging station in Gdańsk, Poland. The calculations of charging process efficiency and range of test drives were conducted in two extreme situations (winter and summer) of sunlight and road conditions. Experiments were performed in the Laboratory of Innovative Power Technologies...
-
Continuous Biomedical Monitoring in VR Scenarios of Socially Smart and Safe Autonomous Vehicle Interaction
PublikacjaPedestrians, as vulnerable road users, pose safety challenges for autonomous vehicles (AVs). Their behavior, often unpredictable and subject to change, complicates AV-pedestrian interactions. To address this uncertainty, AV s can enhance safety by communicating their planned trajectories to pedestrians. In this research, we explore the interaction between pedestrians and autonomous vehicles within an industrial environment, focusing...
-
Rebuilding Bailey Bridge to Bridge With Bascule Span – A Case Study
PublikacjaThe structural analysis of a road foldable prefabricated steel Bailey- type bridge located over the Tuga River in Żelichowo, Poland is performed in this paper. Interesting and untypical bridge redevelopment performed made it possible to lift the middle foldable bridge span by approximately 4.0 m concerning the existing state. The paper begins with a survey of literature carried out on the investigations of foldable Bailey-type...
-
Modeling, simulation, and validation of a TB41 crash test of the H2/W5/B concrete vehicle restraint system
PublikacjaThe paper addresses numerical simulations of a concrete vehicle restraint system. The model is described in detail. The advanced material law of the continuous surface cap model was used to analyze the damage locations in concrete barrier segments. The results were validated against the TB41 full-scale crash test. The test was conducted in compliance with European standard EN 1317, and the validation was performed in accordance...
-
Propagation Loss and Interference Analysis for 5G Systems in the Context of C-ITS System Implementation
PublikacjaThe article presents the concept of implementing subsequent phases of services for the C-ITS system (the Cooperative Intelligent Transport Systems), based on the European Parliament resolution of March 2018. Next, the 5G systems, in the context of their possible cooperation with C-ITS systems, were discussed. Numerical propagation analysis was performed for V2V and V2I type communication based on two different propagation models....
-
The impact of the temperament model on the behavior of an autonomous driver
PublikacjaBecause it is generally believed that the personality and temperament of a human driver influence his/her behavior on the road, the article presents a computational model of the temperament of an autonomous agent - a driver. First, a short review of the four ideas of Galen’s temperament in psychology is presented. Temperament traits are grouped into four other sets, one of which is chosen for implementation in the project of integration...
-
Pedestrian and bicycle bridges as examples of safe collision-free road crossings
PublikacjaPedestrians are most at risk when they are crossing the road. This represents a significant proportion of all fatalities among pedestrians, amounting respectively to 50% in non-built-up areas and 75% in built-up areas. The most frequent reason for this accident is failure to give way. What is most terrible is that 30% of pedestrian accidents occurred at marked pedestrian crossings. Therefore, an important part of pedestrian safety...
-
State of Development of Intelligent Transport Systems Services on National Roads in Poland
PublikacjaIn recent years we can see intensifying implementation of Intelligent Transport System (ITS) measures in Polish cities and on national roads. The architecture of the National Traffic Management System (KSZR) will enable the implementation of a uniform, integrated and intelligent ICT system to launch ITS systems that are the most important for drivers and the General Directorate for National Roads and Motorways (GDDKiA). This paper...
-
Methodology for assessing the lighting of pedestrian crossings based on light intensity parameters
PublikacjaOne of the possible preventive measures that could improve safety at crossings is to assess the state of illumination of the lighting installation located in the transition area for pedestrians. The City of Warsaw has undertaken to comprehensively assess the pedestrian crossings to determine the level of road safety and the condition of lighting. The lighting conditions related to pedestrian crossings without traffic lights in...
-
Driver fatigue detection method based on facial image analysis
PublikacjaNowadays, ensuring road safety is a crucial issue that demands continuous development and measures to minimize the risk of accidents. This paper presents the development of a driver fatigue detection method based on the analysis of facial images. To monitor the driver's condition in real-time, a video camera was used. The method of detection is based on analyzing facial features related to the mouth area and eyes, such as...
-
The Belt and Road Initiative and export variety: 1996–2019
PublikacjaThis study examines the association between the Belt and Road Initiative (BRI) and export variety (EV). We propose three hypotheses on how BRI may foster export markets (destinations) or export product lines. The estimates are based on a dataset constructed specifically for this analysis, covering 183 countries and linked with trade data from 1996 to 2019. We apply the instrumental variable (IV) approach in regressions for covering the...
-
The use of weight in motion data to heavy vehicles - pavement interaction analysis
PublikacjaWeight in motion (WIM) is the element of modern intelligent transport systems created to control commercial vehicles and to detect overloaded items. Because all of the vehicles crossing the WIM station are weighed and recognized, given data can be used to vehicle-pavement interaction analysis. The paper presents the results of analysis based on data from seven WIM stations localized in Motorway and National Roads in Poland. The...
-
Airstrip Ground Improvement Works by Blasting Charge Technique and Dredged-Ash Material Mixture
PublikacjaSoil improvement by blasting charge technique is known in geotechnics as one of the efficient and inexpensive method. It can be used in preparing of underground to found road construction and buildings as well. The technique proves usefulness especially when dynamic load is applied. It is because of non-stiff or rather resilient type soil after improvement. In noncohesive or organic soil, blasting charge...
-
Risk Diagnosis and Management with BBN for Civil Engineering Projects during Construction and Operation
PublikacjaThe authors demonstrate how expert knowledge about the construction and operation phases combined with monitoring data can be utilized for the diagnosis and management of risks typical to large civil engineering projects. The methodology chosen for estimating the probabilities of risk elements is known as Bayesian Belief Networks (BBN). Using a BBN model one can keep on updating the risk event probabilities as the new evidence...
-
Zabezpieczenia antykorozyjne stalowych barierek ochronnych na obiektach mostowych w ujęciu kosztów cyklu ich życia
PublikacjaThe article presents the Life Cycle Costs analysis of steel safety barriers operated in road lane conditions, located on a selected bridge structure. Three corrosion protection systems were proposed, analyzing them in terms of the cost of initial and planned outlays related to maintenance. Based on the LCC analysis for three options, taking into account the 25-year lifetime of the barriers, the optimal solutionwas indicated, i.e....
-
Application of Bayesian Networks in risk diagnostics arising from the degree of urban regeneration area degradation
PublikacjaUrban regeneration as a complex project, generates many extremely specific threats affecting the increase of investment risk. Its unique nature causes that probability parameter, normally applied in the process of risk quantification, is extremely difficult to estimate. Due to lack of historical data urban regeneration related activities are therefore associated with uncertainty. According to the authors, a useful tool for resolving...
-
Potential Application of Solar Energy Systems for Electrified Urban Transportation Systems
PublikacjaThe paper presents a novel approach toward the use of solar energy systems in public transportation. The concept of energy generation in PV systems for supplying a trolleybus transportation system is proposed for the city of Gdynia (Poland). The suggested way of energy production allows reducing the environmental harm impact of the municipal transportation system. Moreover, the proposed way of green energy use can be a more profitable...
-
Comparing the Effectiveness of ANNs and SVMs in Forecasting the Impact of Traffic-Induced Vibrations on Building
PublikacjaTraffic - induced vibrations may cause damage to structural elements and may even lead to structural collapse. The aim of the article is to compare the effectiveness of algorithms in forecasting the impact of vibrations on buildings using the Machine Learning (ML) methods. The paper presents two alternative approaches by using Artificial Neural Networks (ANNs) and Support Vector Machines (SVMs). Factors that may affect traffic-induced...
-
Driver’s Condition Detection System Using Multimodal Imaging and Machine Learning Algorithms
PublikacjaTo this day, driver fatigue remains one of the most significant causes of road accidents. In this paper, a novel way of detecting and monitoring a driver’s physical state has been proposed. The goal of the system was to make use of multimodal imaging from RGB and thermal cameras working simultaneously to monitor the driver’s current condition. A custom dataset was created consisting of thermal and RGB video samples. Acquired data...
-
Visual Traffic Noise Monitoring in Urban Areas
PublikacjaThe paper presents an advanced system for railway and road traffic noise monitoring in metropolitan areas. This system is a functional part of a more complex solution designed for environmental monitoring in cities utilizing analyses of sound, vision and air pollution, based on a ubiquitous computing approach. The system consists of many autonomous, universal measuring units and a multimedia server, which gathers, processes and...
-
Information System for Drivers Within the Integrated Traffic Management System - TRISTAR
PublikacjaAdvanced traveler information systems (ATIS) for drivers are a very important element of modern traffic management. In recent years ITS infrastructure is being developed also in Poland. It allows for delivering to drivers information related to the conditions in the road network through, inter alia, dedicated Variable Message Signs (VMS). Such information enables drivers to take decisions, contributing to improving the efficiency...
-
Determination of equivalent axle load factors with the use of strain energy of distortion
PublikacjaThe paper proposes a new method for calculation of equivalent axle load factors based on the analysis of strain energy of distortion induced in road pavements by traffic loads. The main advantage of the method is the more accurate calculation of the effects of multiple axles and super single versus dual tyres. The methodconsiders the location of critical points, at which strain energy of distortion reaches extreme values. When...
-
Design of poroelastic wearing course with the use of direct shear test
PublikacjaPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
The Effect of Flexible Pavement Mechanics on the Accuracy of Axle Load Sensors in Vehicle Weigh-in-Motion Systems
PublikacjaWeigh-in-Motion systems are tools to prevent road pavements from the adverse phenomena of vehicle overloading. However, the effectiveness of these systems can be significantly increased by improving weighing accuracy, which is now insufficient for direct enforcement of overloaded vehicles. Field tests show that the accuracy of Weigh-in-Motion axle load sensors installed in the flexible (asphalt) pavements depends on pavement temperature...
-
Application of BN in Risk Diagnostics Arising from the Degree of Urban Regeneration Area Degradation
PublikacjaUrban regeneration as a complex project, generates many extremely specific threats affecting the increase of investment risk. Its unique nature causes that probability parameter, normally applied in the process of risk quantification, is extremely difficult to estimate. Due to lack of historical data urban regeneration related activities are therefore associated with uncertainty. According to the authors, a useful tool for resolving...
-
Low-Temperature Requirements for Bitumen in Central East European Road Construction
PublikacjaThe paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....
-
Lighting requirements for pedestrian crossings - positive contrast
PublikacjaFor many years now in Poland there has been a large number of road accidents at pedestrian crossings during night periods [5, 11]. One of the technical solutions that can improve this condition is the use of proper lighting for pedestrian crossings. The designated pedestrian crossing should be visible in different weather conditions and at different times of the day. In case of night vision restrictions use artificial lighting...
-
Impact of Intelligent Transport Systems Services on the Level of Safety and Improvement of Traffic Conditions
PublikacjaThe positive effects of the services of Intelligent Transport Systems (ITS) on the level of transport systems operation was confirmed by long-term studies conducted, inter alia, in the USA, Japan and Europe. Benefits resulting from the application of ITS services can be presented through performance indicators. The indicators represent in a numerical or qualitative manner to what extent ITS services can contribute to improving...
-
Vehicle detector training with labels derived from background subtraction algorithms in video surveillance
PublikacjaVehicle detection in video from a miniature station- ary closed-circuit television (CCTV) camera is discussed in the paper. The camera provides one of components of the intelligent road sign developed in the project concerning the traffic control with the use of autonomous devices being developed. Modern Convolutional Neural Network (CNN) based detectors need big data input, usually demanding their manual labeling. In the presented...
-
Fuel price, income and road safety as determinants of the level of the population’s economic well-being in Poland
PublikacjaThe opportunity to travel is one of the most favorite human activities, given that on a trip a person gets new knowledge, impressions and positive emotions. Recreational trips occupy a prominent place in the concept of the economics of happiness, and the study of factors that influence decision-making regarding travel is important for forecasting the number of tourists, infrastructure development, income and expenses of businesses...
-
Multimodal Surveillance Based Personal Protection System
PublikacjaA novel, multimodal approach for automatic detection of abduction of a protected individual, employing dedicated personal protection device and a city monitoring system is proposed and overviewed. The solution is based on combining four modalities (signals coming from: Bluetooth, fixed and PTZ cameras, thermal camera, acoustic sensors). The Bluetooth signal is used continuously to monitor the protected person presence, and in case...
-
Determination of the Bending Properties of Wire Rope Used in Cable Barrier Systems
PublikacjaThis paper presents research on the bending properties of 3 × 7 19-mm wire rope commonly used in road cable barriers. A total of 19 experimental tests were conducted. In addition, two nonlinear 3D numerical models of the wire rope using beam and solid finite elements were developed. Based on these models, four numerical simulations were carried out. The numerical results were validated against the experimental ones and a very good...
-
Automation of the Road Gate Operations Process at the Container Terminal—A Case Study of DCT Gdańsk SA
PublikacjaThe future increased terminal capacity will result in more container movement through the road complex and rail siding, which are one of the most critical areas (potential bottlenecks) in the container terminal. Truck turnaround time is one of the major factors that customers take into account while deciding how many container volumes they will handle through the container terminal. To enable to optimize increased traffic with...
-
Poroelastic Road Surfaces - State of The Art
PublikacjaPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
Risks associated with the transportation of hazardous materials on public roads
PublikacjaA significant proportion of the transport of hazardous materials is carried out on public roads. Therefore, the safety of such transport is becoming increasingly important. Every catastrophe involving hazardous materials has a negative impact on direct road users and the surrounding environment, becauses its range is mostly not local. It follows that in the event of such catastrophe, its effects should be minimized. This is possible...
-
Laboratory Determination of Burger's Model Parameters for Visco-elastic Analysis of Road Pavement Materials
PublikacjaBurger's Model is one of those models that describes performance of asphalt mixtures. Its parameters can be used in road construction analysis based on visco-elastic properties in wide variety of temperatures using dedicated programs (e.g. Veroad) or in Finite Element Method (FEM). Parameters of Burger's Model can be used for example in prediction of low temperature cracking in low winter temperatures or permanent deformation...
-
Impact of accuracy of weigh-in-motion data for pavement analysis and design: influence of temperature variations
PublikacjaThis paper investigates the effect of temperature on WIM-collected data using the steering axle load spectrum (SALS) and two datasets. The first dataset, provided by the WIM system operator, contains detailed raw data, while the second, supplied by the road authority, includes less detailed information but covers 46 stations with various sensor types and configurations: single-line bending plates and two-line quartz piezoelectric...
-
Western Front of the City Centre of Gdańsk. An Urban Conservation Study
PublikacjaThe western front of Gdańsk`s city centre is the key fragment of a ring road scheme, which was created at the turn of the 20th century during the great transformation of the city. It was at that time that new streets and squares were delineated on the site of the early modern earthen bastions, which for more than three centuries marked Gdańsk`s border. The new city development was set up in their surroundings. In 1945, Gdańsk was...
-
One year performance evaluation of low volume road with cold recycled base course on the basis of FWD and Dynamic Modulus tests
PublikacjaArticle presents results of assessment of performance of trial section of flexible pavement with cold recycled base constructed on low volume road within typical contract conditions. Performance evaluation was made based on Falling Weight Deflectometer (FWD) test performed during construction stage – 2 times on the top of cold recycled base course – 28 and 180 days after compaction of base course and 2 times on the top of the wearing...
-
Estimation of Vehicle Energy Consumption at Intersections Using Microscopic Traffic Models
PublikacjaThis paper addresses issues related to modeling energy consumption and emissions using microscopic traffic simulations. This paper develops a method in which a traffic model is used to calculate the energy needed to travel through selected types of intersections. This paper focuses on energy consumption and derived values of calculated energy, which can be, for example, carbon dioxide emissions. The authors present a review of...
-
Rospuda - czy wszędzie budować mosty?
PublikacjaStreszczenie - SummaryThe article presents the problem of planning transport system in the areas of high natural and landscape values. Bridges and roads crossing valuable areas undergo Environmental Impact Assessment (EIA) Procedure. This procedure in Poland is often treated only as formal requirement, not as an instrument helping to solve conflicts and to minimise negative environmental and landscape effects. The potential of...
-
Development of the New Polish Method for Capacity Analysis of Motorways and Expressways
PublikacjaThe paper presents development of the new Polish method for performing capacity analysis of basic segments of dual carriageway roads (motorways and expressways). The method is based on field traffic surveys conducted at 30 motorway and expressway sites (class A and S roads) in Poland. Traffic flows, composition and travel times were observed in 15-min intervals at each site using ANPR filming method. These data were used to calibrate...
-
Localization of sound sources with dual acoustic vector sensor
PublikacjaThe aim of the work is to estimate the position of sound sources. The proposed method uses a setup of two acoustic vector sensors (AVS). The intersection of azimuth rays from each AVS should indicate the position of a source. In practice, the result of position estimation using this method is an area rather than a point. This is a result of inaccuracy of the individual sensors, but more importantly, of the influence of a source...
-
A Survey of Vehicular Network Systems for Road Traffic Management
PublikacjaIn this survey, we analyze the proposals of vehicular communication systems in the context of road traffic management. Starting with the definition of communications between vehicles (V2V), vehicles-to-infrastructure (V2I) and vehicles-to-everything (V2X), we first focus on the requirements and current standards for the Intelligent Transport Systems (ITS), including the maximum communication delay, the communication range and the...
-
COMPARISON OF NOISE EMISSION OF HCT AND CLASSIC VEHICLE COMBINATIONS FOR TIMBER TRANSPORTATION IN SWEDEN
PublikacjaBy means of a special simulation tool, the noise emission of a high-capacity heavy vehicle (11 axles) was compared to that of a classic heavy vehicle (a truck-dolly-semitrailer with 8 axles). The two cases are designated “Extended vehicle” versus “Classic vehicle” in this study, having total lengths of 34 and 25 m, respectively. The Classic vehicle represents the most common articulated heavy vehicle configuration for transport...
-
At what temperature should the tire rolling resistance be measured?
PublikacjaThe climate crisis is already an indisputable fact and therefore, it is necessary to reduce energy consumption, and especially energy wasting. One of the ways to reduce energy consumption of motor vehicles is to decrease vehicle movement resistance, including rolling resistance. In order for the optimization of tire rolling resistance to be efficient, it is necessary to apply appropriate optimization criteria that are closely related...
-
Four-state stochastic model of changes in the reliability states of a motor vehicle
PublikacjaThe properties of semi-Markov processes have been generally characterized and the applicability of the theory of such processes to the determining of the reliability of motor cars and other road vehicles has been explained. A formal description of the process of changes in the motor vehicle technical states considered as reliability states and a model of this process in the form of a one-dimensional stochastic process have been...
-
Recycled Polyethylene terephthalate (PET) as Construction Material in Civil Engineering: A Review
PublikacjaIn general, the quantity of plastics of all types consumed annually all over the world has been growing in a phenomenal way. The manufacturing processes, service industries and municipal solid wastes (MSW) generate numerous waste plastic materials. The increasing awareness about the environment has tremendously contributed to the concerns related with disposal of the generated wastes. It is believed that the management of solid...