Wyszukiwarka
Wyniki wyszukiwania dla: corrosion, guided waves, non-destructive testing, ship structures
-
Influence of laser melting on surface layer properties of titanium alloy Ti6Al4V
PublikacjaIn time of rapid technology and medicine progress, implants are becoming more widely used in the human body, ranging from dental implants, stabilizing plates, screws, orthopaedic prostheses. For example, there are many types of hip prostheses used for hip replacement as well as various types of materials used for these orthopaedic prostheses. Properties of titanium alloys used in hip prostheses combined with good strength properties,...
-
2022-2023 - Strenght of materials towards applications, PG_00053661
Kursy OnlineThe course is mainly dedicated to the DAPE Students. From the theoretical point of view the course consists of the following problems to be discussed during the lectures and exercises: -fundamentals of strength of materials -basic structures and environment -loads on structures -strength of materials: tension, stress, analysis of stress and strain, bending moments and shearing forces, longitudinal and shearing stress in beams,...
-
Strenght of materials towards applications , PG_00053661
Kursy OnlineThe course is dedicated to the DAPE WIMiO Students. From the theoretical point of view the course consists of the following problems to be discussed during the lectures: -fundamentals of strength of materials -basic structures and environment -loads on structures -strength of materials: tension, stress, analysis of stress and strain, bending moments and shearing forces, longitudinal and shearing stress in beams, bending stress...
-
Opracowanie ekspertyzy dotyczącej przyczyn pękania łopatek wirnika SP turbiny PG1 typu 13UP55
PublikacjaZakres badań i analiz dotyczył ustalenia przyczyn pękania elementów łopatek wirnika SPA5 turbiny TG1 typu 13UP55 obejmował: 1. wykonanie badań składu chemicznego stali, z której wykonano łopatki dostarczone przez Zleceniodawcę dwoma metodami, 2. badania mikroobszarów zniszczenia łopatek na mikroskopie elektronowym skaningowym z mikroanalizatorem EDS, 3. badania metalograficzne makroskopowe i mikroskopowe fragmentów...
-
FEM simulation of laminate failure in the three point bending
PublikacjaThe paper presents a FEM simulation of failure of laminate subjected to the three point bending. The numeri-cal model is based on the equivalent single layer approach with 6-paramater non-linear shell theory kinematics. It is implemented in the non-commercial FEM code. The failure initiation is detected with the use of Tsai-Wu criterion. After the failure onset the progressive failure process is modelled through the appropriate...
-
Underwater Local Cavity Welding of S460N Steel
PublikacjaIn this paper, a comparison of the mechanical properties of high-strength low-alloy S460Nsteel welded joints is presented. The welded joints were made by the gas metal arc welding (GMAW)process in the air environment and water, by the local cavity welding method. Welded joints were testedfollowing the EN ISO 15614-1:2017 standard. After welding, the non-destructive—visual, penetrant,radiographic, and ultrasonic (phased array) tests...
-
Linear-scaling calculation of Hartree-Fock exchange energy with Non-orthogonal Generalised Wannier Functions
PublikacjaWe present a method for the calculation of four-centre two-electron repulsion integrals in terms of localised non-orthogonal generalised Wannier functions (NGWFs). Our method has been imple- mented in the ONETEP program and is used to compute the Hartree-Fock exchange energy component of Hartree-Fock and Density Functional Theory (DFT) calculations with hybrid exchange-correlation functionals. As the NGWFs are optimised in situ...
-
Cable-stayed bridges. Basic static schemes
PublikacjaThe paper presents an overview of shaping of cable-stayed bridges. Historical background, basic static sketches and overview of selected bridges are included. Selected natural solutions and interesting unrealized projects were presented. Basic ideas and most important principals are discussed. The examples and sketches were given an author's comment. Static diagrams of two pylon structures with three variants of the arrangement...
-
Buckling of braced frames
PublikacjaIn this paper the classical Winter model, developed originally for columns is applied for frame structures and compared with the results of parametric study of frame with bracing. Sensitivity analysis of critical loads of frame due to bracing stiffness is carried out and the threshold bracing stiffness for full bracing is found. In the non-linear statical analysis the forces in bracings are calculated.
-
The development of an underwater telephone for digital communication purposes
PublikacjaThe underwater telephone HTL-10 has been designed to provide voice and data communication between helicopter and submarines using acoustic waves. It works in a half-duplex mode and uses analogue power-efficient modulation in the form of a single side-band, suppressed carrier, in a wide range of frequencies. It generates the transmitted signal, and processes the received signals. It is implemented with the use of digital signal...
-
Minimal surfaces and conservation laws for bidimensional structures
PublikacjaWe discuss conservation laws for thin structures which could be modeled as a material minimal surface, i.e., a surface with zero mean curvatures. The models of an elastic membrane and micropolar (six-parameter) shell undergoing finite deformations are considered. We show that for a minimal surface, it is possible to formulate a conservation law similar to three-dimensional non-linear elasticity. It brings us a path-independent...
-
Stress–strain model of lower corroded steel plates of normal strength for fitness-for-purpose analyses
PublikacjaThis study investigates the mechanical properties of specimens made of normal strength steel subjected to lower marine immersed corrosion degradation levels (below 25 %). The specimens were corroded in laboratory conditions, and only natural factors were controlled to raise the corrosion rate (reaching the level of 1 mm/year). Three different thicknesses of plates made of normal strength of shipbuilding steel are investigated (between...
-
Wojciech Sadowski prof. dr hab. inż.
OsobyWojciech Sadowski (ur. 2.02.1954 r. w Ostaszewie), naukowiec, polski inżynier, profesor Politechniki Gdańskiej, specjalista z fizyki ciała stałego, nanotechnologii, optoelektroniki. Studia wyższe ukończył w 1979 r. w Leningradzkim Instytucie Elektrotechnicznym w Leningradzie w specjalności dielektryki i półprzewodniki, uzyskując tytuł zawodowy magistra inżyniera elektronika. Od 1979 r. pracuje na Politechnice Gdańskiej, pełniąc...
-
Badania i analizy kolejowych konstrukcji odciążających typu mostowego
PublikacjaW pracy przedstawiono i omówiono wybrane modele obliczeniowe, wyniki analiz teoretycznych oraz badań trzech typów kolejowych konstrukcji odciążających typu mostowego. Zaprezentowano modele obliczeniowe oraz metodykę badań in situ tego typu konbstrukcji. Przedstawiono wnioski dotyczące zaawansowanych metod obliczeniowych rozszerzonych badań in situ w celu diagnozowania rzeczywistej pracy obiektów mostowych.
-
Application of the Mathar method to identify internal stress variation in steel as a welding process result
PublikacjaThe paper deals with the method to identify internal stresses in two-dimensional steel members. Steel members were investigated in the delivery stage and after assembly, by means of electric-arc welding. In order to perform the member assessment two methods to identify the stress variation were applied. The first is a non-destructive measurement method employing local external magnetic field and to detecting the induced voltage,...
-
Deterioration of masonry structure investigated by a thermal camera with a qualitative assessment of thermal image processing
PublikacjaThermal imaging is contemporary remote sensing measurement technique, which provides an image of the temperature distribution in the measured object. The method is widely used, due to its mobility as well as the non-destructive character of the measurement. Infrared thermography is especially relevant in the inspection of insulation, what is more, it is a suitable device for detecting thermal bridges and structural changes, which...
-
State equations in the mathematical model of dynamic behaviour of multihull floating unit
PublikacjaPrzedstawiony artykuł dotyczy dynamiki wielokadłubowej jednostki pływającej typu katamaran poddanej wymuszeniom pochodzącym od falowania nieregularnego. Analiza dynamiki jednostki wielokadłubowej została przeprowadzona przy założeniu, że model układu jest modelem liniowym na który działa fala nieregularna. Model matematyczny takiego układu dynamicznego jest reprezentowany poprzez równania stanu. Zapisane zostały równania uwzględniające...
-
Non-linear FEM analysis of pounding-involved response of buildings under non-uniform earthquake excitation
PublikacjaThe aim of the paper is to show the results of the study investigating the influence of non-uniform earthquake excitation, due to spatial seismic effects connected with the propagation of seismic wave, on the pounding-involved response of two buildings. The three-dimensional non-linear FEM analysis has been conducted using the detailed models of colliding structures. Acceleration records for different structural supports have been...
-
Low-Cost Open-Hardware System for Measurements of Antenna Far-Field Characteristics in Non-Anechoic Environments
PublikacjaExperimental validation belongs to the most important steps in the development of antenna structures. Measurements are normally performed in expensive, dedicated facilities such as anechoic chambers, or open-test sites. A high cost of their construction might not be justified when the main goal of antenna verification boils down to demonstration of the measurement procedure, or rough validation of the simulation models used for...
-
Identyfikacja gatunku stali zastosowanej w obiektach budowlanych
PublikacjaEksploatacja istniejących metalowych konstrukcji budowlanych często związana jest z zagadnieniem koniecznej szczegółowej identyfikacji rodzaju materiału stalowego pod kątem je go cech wytrzymałościowych i składu chemicznego. Dostępne standardowe metody laboratoryjne zazwyczaj wymagają pobrania z konstrukcji próbek materiału do badań, co nie zawsze jest możliwe. W artykule zaprezentowano alternatywne metody oceny wymienionych cech...
-
Challenges in operating and testing loop heat pipes in 500–700 K temperature ranges
PublikacjaThe potential applications of loop heat pipes (LHPs) are the nuclear power space systems, fuel cell thermal management systems, waste heat recovery systems, medium temperature electronic systems, medium temperature military systems, among others. Such applications usually operate in temperature ranges between 500–700 K, hence it is necessary to develop an LHP system that will meet this requirement. Such a thermal management device...
-
Selection of Organic Coating Systems for Corrosion Protection of Industrial Equipment
PublikacjaThe most important element of corrosion protection in industrial conditions is the protective coating system. However, selecting the right coating can often be a real problem due to the sheer number of coating manufacturers and their products on the market. A quantitative approach based on the data mining technique used to analyze the obtained multi-site exposure data has been proposed. This was demonstrated by the example of the...
-
The retrofitting of ships by applying retractable bow hydrofoils: a case study
PublikacjaIncreasing environmental requirements and a relatively long ship life of 30 years mean more attention is needed to retrofit existing ships. One possibility is using hydrofoils to reduce the ship’s resistance and improve comfort and safety in rough sea conditions. This study investigates the influence of retractable bow hydrofoils on the seakeeping performance and operational conditions of a selected case study vessel (V-shaped...
-
4D Models in World Wide Web
PublikacjaThe paper presents some results of research curried out within the framework of the European project named "Cultural Heritage Through Time" (CHT2). One of the main project aims were to develop a methodology for sharing multi-temporal information via the Internet (webGIS) for remote analysis of structures and landscapes over time. Reported in this paper results are focused on testing two technologies (Hexagon and Esri) for online...
-
Random field modelling of mechanical behaviour of corroded thin steel plate specimens
PublikacjaThe objective of this work is to explore the possibility of corrosion degradation modelling of thin steel plate specimens with the use of random field approach. The mechanical properties are obtained via the nonlinear Finite Element Analysis with the use of an explicit dynamic solver. The fully nonlinear material model is adopted to obtain the proper stress-strain response. Sensitivity analysis considering the main statistical...
-
The effect of macro polymer fibres length and content on the fibre reinforced concrete
PublikacjaThe paper presents studies of a ready-mix concrete containing polymer fibres of three different lengths: 24, 38 and 54 mm. The performed tests allowed to determine the effect of fibre volume fraction and length on the concrete strength. The basic parameters of concrete mixture (consistency, air content and bulk density) were identified. Fibre reinforced concrete belongs to a group of composite materials. The polymer fibres are...
-
Performance of organic coatings upon cyclic mechanical load
PublikacjaA number of engineering structures fail due to the fatigue damage resulting from cyclic mechanical stress. However, as far as organic coatings are concerned this degradation factor remains underestimated. In the paper the authors propose a methodology combining global electrochemical impedance spectroscopy and local atomic force microscopy measurements for evaluation of coating resistance to an impact of repetitive mechanical stress. Typical...
-
Stability Analysis of the Floating Offshore Wind Turbine Support Structure of Cell Spar Type During its Installation
PublikacjaThe article presents the results of selected works related to the wider subject of the research conducted at the Faculty of Ocean Engineering and Ship Technology of the Gdansk University of Technology, which concerns design and technology of construction, towing, and settlement on the seabed, or anchoring, of supporting structures for offshore wind farms. As a result of this research, several designs of this type of objects were...
-
Acoustic journal bearing - A search for adequate configuration
PublikacjaClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
-
NetBaltic System-Heterogenous Wireless Network for Maritime Communications
PublikacjaIn case of maritime communications, we observe a growing interest in deployment of multitask satellite-based solutions and development of new maritime-specific systems intended for improvements in safety of e-navigation. Analysis of different types of currently used maritime communication systems leads, however, to a conclusion that neither global and still very expensive satellite systems nor cheaper, but short-ranged transmission...
-
The concept of research on ecological, energy and reliability effects of modified marine fuel oils application to supply compression-ignition engines in real conditions
PublikacjaWithin the article, basic assumptions of the research project financed by Regional Fund for Environmental Protection and Water in Gdansk were described. The project concerns the experimental investigations carried out on laboratory compression-ignition engine in conditions of its supply with a non-standard marine fuel oil. Configuration and measuring capability of laboratory test bed presently being constructed were introduced....
-
Speed Observer Structure of Induction Machine Based on Sliding Super-Twisting and Backstepping Techniques
PublikacjaThis paper presents an analysis of the two speed observer structures which are based on the backstepping and sliding super twisting approach. The observer stabilizing functions result from the Lyapunov theorem. To obtain the observer tuning gains the observer structure is linearized near the equilibrium point. The rotor angular speed is obtained from non-adaptive dependence. In the sensorless control system structure the classical...
-
Seismic Pounding Between Bridge Segments: A State-of-the-Art Review
PublikacjaEarthquake-induced structural pounding in bridge structures has been observed in several previous seismic events. Collisions occur at the expansion joints provided between adjacent decks or between the deck and abutment. Pounding between the structural elements may lead to severe damages and even to the unseating of the bridge in certain cases. Several investigations have been performed to study pounding in bridges under uniform...
-
Numerical Study of Concrete Mesostructure Effect on Lamb Wave Propagation
PublikacjaThe article presents the results of the numerical investigation of Lamb wave propagation in concrete plates while taking into account the complex concrete mesostructure. Several concrete models with randomly distributed aggregates were generated with the use of the Monte Carlo method. The influence of aggregate ratio and particle size on dispersion curves representing Lamb wave modes was analyzed. The results obtained for heterogeneous...
-
Impact of steel grade on a ship colliding with an offshore wind turbine monopile supporting structure
PublikacjaOffshore wind power is experiencing rapid development around the world. The number of installations and their size is growing. Thousands of monopile support structures with diameters of 10 m and weights of 2000 tons will be installed in the coming years. Offshore wind power installations, often located close to the shore and shipping routes, pose a new challenge to ship safety. The study analyses the damages from an accidental...
-
Techniczne aspekty implementacji nowoczesnej platformy e-learningowej
PublikacjaZaprezentowano aspekty techniczne implementacji nowoczesnej platformy nauczania zdalnego. Omówiono obszary funkcjonalne takie jak: system zarządzania nauczaniem, serwis informacyjny, dodatkowe oprogramowanie dydaktyczne oraz kolekcja zasobów multimedialnych. Przybliżono zagadnienia związane z bezpieczeństwem takiej platformy. Na końcu przedstawiono parametry techniczne wdrożonej na Politechnice Gdańskiej platformy eNauczanie.
-
Lossless Compression of Binary Trees with Correlated Vertex Names
PublikacjaCompression schemes for advanced data structures have become the challenge of today. Information theory has traditionally dealt with conventional data such as text, image, or video. In contrast, most data available today is multitype and context-dependent. To meet this challenge, we have recently initiated a systematic study of advanced data structures such as unlabeled graphs [1]. In this paper, we continue this program by considering...
-
The influence of the welding environment on the properties of Tekken joints made from S355J2C+N steel
PublikacjaThere are three main methods of underwater welding: dry, wet and intermediate between them, by using the local dry chamber. Due to low costs, the most common method is the wet welding with the use of covered electrodes. Water as a welding environment carries out a lot of problems. The first is limited visibility and instability of the welding arc. The biggest problem during underwater welding is high susceptibility to cold cracking,...
-
Designate CTOD Heat Affected Zone of butt weld, Report No: WOiO/II/76/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
Designate CTOD of Weld Metal of butt weld, No WOiO/II/108/2013
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability...
-
CTOD designation for WM and HAZ in butt joint made from S460 ML steel, Expertise No. WOiO/II/82/2015
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Designate of CTOD for WM and HAZ, report no: WOiO/II/122/2014
PublikacjaTypical (normative) testing of materials and/or welded joints do not answer on all questions about material or welded joint properties. In ship building and off-shore sectors, many strucures requires materials and joint with higher than typical fatigue resistance. Imact tests, which are carried out during welding technology qualification, gives answer about ductility, CTOD tests results about material or welded joint ability to...
-
Smooth least absolute deviation estimators for outlier-proof identification
PublikacjaThe paper proposes to identify the parameters of linear dynamic models based on the original implementation of least absolute deviation estimators. It is known that the object estimation procedures synthesized in the sense of the least sum of absolute prediction errors are particularly resistant to occasional outliers and gaps in the analyzed system data series, while the classical least squares procedure unfortunately becomes...
-
COMPARISON OF TWO MODELS OF CONDENSATION
PublikacjaIn the low-pressure part of steam turbine, the state path usually crosses the saturation line in penultimate stages. At least last two stages of this part of turbines operate in two –phase region. The liquid phase in this region in mainly created in the process of homogeneous and heterogeneous condensation. Several observations confirm however, that condensation often occurs earlier than it is predicted by theory i.e. before the...
-
Performance of zinc-rich coatings evaluated using AFM-based electrical properties imaging
PublikacjaThe paper presents the results of investigation of polyvinyl zinc-rich coating exposed to 97% relativehumidity atmosphere for 40 days. Condition of the coating and evolution of its protective properties weredetermined with the novel AFM-based approach capable of providing surface profiles, local dc currentmaps as well as local impedance spectra. The proposed technique allowed insight into the local changesof coating topography...
-
Diagnostic tolerances' evaluation method of the start-up exhaust temperature of a naval gas turbine
PublikacjaThe conducted investigations aimed to elaborate the method of marking diagnostic tolerances of the exhaust temperature of a gas turbine observed during engine's start-up process. The diagnostic tolerances were determined by means of statistical inference by creating the hypothesis about a normal distribution of the start-up exhaust temperature's dispersion in the initial operation moment, which was subsequently verified applying...
-
On ship roll resonance frequency
PublikacjaThe paper deals with the problem of modeling of rolling motion under a variety of excitation parameters. Special emphasis is put on the analysis and prediction of the frequency of the resonant mode of rolling, since it is often an essential issue in terms of motion of a ship related to her safety against capsizing or excessive amplitudes of roll. The research is performed for both free rolling and excited rolling and it is based...
-
Effect of wet Hydrogen Sulfide on Carbon Steels Degradation in Refinery Based on Case Study
PublikacjaMaterial degradation caused by wet hydrogen sulfide (Wet H2S) is one of the major issues in refineries. Carbon steel is the main construction material used in refineries and is subjected not only to thickness loss but the hydrogen is the major concern. H2S leads to high atomic hydrogen penetration in steel which causes degradation in the form of blistering and/or cracking (HIC/SOHIC) and stress cracking in the area of welds and...
-
Designing a High-sensitivity Microscale Triple-band Biosensor based on Terahertz MTMs to provide a perfect absorber for Non-Melanoma Skin Cancer diagnostic
PublikacjaNon-melanoma skin cancer (NMSC) is among the most prevalent forms of cancer originating in the top layer of the skin, with basal cell carcinoma (BCC) and squamous cell carcinoma (SCC) being its primary categories. While both types are highly treatable, the success of treatment hinges on early diagnosis. Early-stage NMSC detection can be achieved through clinical examination, typically involving visual inspection. An alternative,...
-
Investigation of natural frequencies of axially loaded thin-walled columns
PublikacjaThe paper deals with correlation between natural frequencies of two steel thin-walled columns and the corresponding applied load. The structures are made of cold-formed lipped channel sections. The columns lengths were assumed to follow two buckling patterns – global flexural and flexural-torsional buckling. In the thicker structure two material models were considered – linearly-elastic and elastic-perfectly plastic. Numerical...