Filtry
wszystkich: 5141
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: SHEAR STRENGTH PARAMETERS
-
Evaluation of susceptibility of high-strength steels to hydrogen delayed cracking
PublikacjaPrzedstawiono wyniki badań podatności na opóźnine pękanie wodorowe stali o wysokiej wytrzymałości w oparciu o próbę stałego obciążenia. Badano stal do pracy w podwyższonych temperaturach 26H2MF oraz stal do ulepszania cieplnego 34HNM w środowisku przepracowanego oleju silnikowego. Badano również stal 14HNMBCu i jej złącza spawane w środowisku wody morskiej przy polaryzacji katodowej.
-
Influence of pitting corrosion on strength of steel ships and offshore structures
PublikacjaPraca dotyczy wpływu korozji wżerowej na własności mechaniczne stali o zwykłej i podwyższonej wytrzymałości oraz na wytrzymałość stalowych konstrukcji przy obciążeniach statycznych i quasi- statycznych. Artykuł oparty jest głównie na japońskich publikacjach. W próbie rozciągania, korozja wżerowa obniża nieznacznie obciążenie odpowiadające granicy plastyczności Re(nieznacznie) i wytrzymałości na rozciąganie Rm (silniej, redukuje...
-
Mechanical Strength of MV Ship-switchgear During Fault Arc
PublikacjaIn the paper the analysis of pressure stressed in enclosure during fault arc inside switchgear is pre-sented as well. There is introduced the method based on determining stresses which are sum of tensile stresses (membrane) and deflection stresses. For tensile stresses nalysis the energy method, for unrestrainedly supported rectangular plate, was used. In the further part of the paper, the calculations and measurements results...
-
The initial selection of parameters for dynamic brake for car engine test dynamometer
PublikacjaThe article presents an analysis of the car engine loads. The aim of the analysis was to determine the parameters of the brake / electric motor on an engine test bad. Analysis of loads on the driving tests concerned on chassis dynamo to simulate them on an engine dynamometer. To check the range of dynamometer shaft angular acceleration inertial mass of a car was reduced on the crankshaft axis. The calculations of maximum shaft...
-
Analysis the Parameters of the Adaptive Controller for Quality Control of Dissolved Oxygen Concentration
PublikacjaThe wastewater treatment plant can be considered a dynamic large scale complex system, in which the most important control parameter is the dissolved oxygen concentration in the aerobic zone. The air is supplied to this zone by the aeration system. In the paper, both the sequencing batch reactor and the aeration system are modelled and used as plant of control performed by the cascade nonlinear adaptive control system extended...
-
Iterative‐recursive estimation of parameters of regression models with resistance to outliers on practical examples
PublikacjaHere, identification of processes and systems in the sense of the least sum of absolute values is taken into consideration. The respective absolute value estimators are recognised as exceptionally insensitive to large measurement faults or other defects in the processed data, whereas the classical least squares procedure appears to be completely impractical for processing the data contaminated with such parasitic distortions. Since...
-
The influence of drying parameters on wood properties
PublikacjaResults of influence of gas-steam mixture drying process on wood mechanical properties are presented. Wood species, namely pine (Pinus sylvestris L.) and beech (Fagus silvatica L.) from the northern part of Pomerania region in Poland, were subject of steam kiln-drying process in a laboratory kiln specially arranged for that reason.
-
The influence of drying parameters on wood properties
PublikacjaThe influence of drying conditions on wood properties is presented. The classical approach was used to determine energetic effects (cutting forces and cutting power) of wood sawing process on the basis of the wood specific cutting resistance, material constant. Before mashining wood material (soft and hard) was dryied at various conditions using air at 25oC, air-steam meaxture at 80oC and steam at 110oC.
-
Selection of the tunnel thuster main parameters.
PublikacjaPrzedstawiono przegląd podstawowych odmian konstrukcyjnych sterów strumieniowych urządzeń zalecanych przez producentów. Z uwagi na znaczne różnice wartości otrzymywane z wymienionych metod, zamieszczono także wyniki analizy statystycznej sterów strumieniowych zastosowanych na statkach zbudowanych w Stoczni Gdynia w latach1995-2002. Porównanie wyników poszczególnych metod z parametrami sterów zastosowanych na wymienionych...
-
Application of total parameters in environmental analytics
PublikacjaPrzedstawiono klasyfikację technik oznaczania tzw. parametrów sumarycznych w próbkach środowiskowych (powietrze, woda, gleba) oraz obszar wykorzystania parametrów sumarycznych w analityce środowiskowej.
-
Frequency Diagnostics of Transformer Insulating Parameters
PublikacjaIn the article is presented experimental analysis and diagnostics of insulating system oil-paper for power transformers, mainly by progressive frequency method – dielectric spectroscopy. In the 1-st part of the article is described base theory about measurement and diagnostics insulating part (oil and paper) of power transformers. In the 2-nd part of article is described measuring method of insulating frequency diagnostics - frequency...
-
A highly-efficient technique for evaluating bond-orientational order parameters
PublikacjaWe propose a novel, highly-efficient approach for the evaluation of bond-orientational order parameters (BOPs). Our approach exploits the properties of spherical harmonics and Wigner 3jj-symbols to reduce the number of terms in the expressions for BOPs, and employs simultaneous interpolation of normalised associated Legendre polynomials and trigonometric functions to dramatically reduce the total number of arithmetic operations....
-
Establishing Relationships between Parameters of the controlled Compaction Soil by Using Various In-Situ Tests
PublikacjaThe aim of research was evaluating reliable correlations between chosen soil parameters describing state of surface layers of soil. The paper presents site comparative tests based on the light falling weight deflectometer (LFWD), the static plate load tester (VSS), the dynamic probing light tester (DPL) and the bearing ratio tester (CBR in-situ) with relationships between soil state parameters. All featured in-situ...
-
Non-conventional approach in single-sided lapping process: kinematic analysis and parameters optimization
PublikacjaThe lapping process is strongly affected by a number of input parameters. One of the fundamental mechanical processes in lapping is the abrasive effect of particles. In order to examine the influence of the kinematic parameters on the lapping uniformity of unconventional single-sided machine, numerical simulations of particles sliding trajectories are performed. Changing the kinematic parameters, e.g., rotational velocities or...
-
Advanced sensitivity analysis of the impact of the temporal distribution and intensity of rainfall on hydrograph parameters in urban catchments
PublikacjaKnowledge of the variability of the hydrograph of outflow from urban catchments is highly important for measurements and evaluation of the operation of sewer networks. Currently, hydrodynamic models are most frequently used for hydrograph modeling. Since a large number of their parameters have to be identified, there may be problems at the calibration stage. Hence, sensitivity analysis is used to limit the number of parameters....
-
Traffic model for evaluation of call processing performance parameters in IMS-based NGN
PublikacjaIn the modern world requirements for accurate and fast information distribution are becoming more and more important, which creates a strong necessity for appropriate telecommunication network architecture. Proposition of such an architecture is the Next Generation Network (NGN) concept, which in order to guarantee Quality of Service (QoS), should be correctly designed and dimensioned. For this reason proper traffic models must...
-
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublikacjaThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
Scale effect in shaft friction from direct shear tests
PublikacjaPrzeanalizowano wartości maksymalne tarcia uzyskane w aparacie bezpośredniego ścinania w kontakcie konstrukcja-grunt dla piasków kwarcowych i węglanowych oraz gładkiego i szorstkiego kontaktu. Badania przeprowadzono przy regulowanej sztywności normalnej kontaktu, przy różnej składowej normalnej naprężenia w kontakcie i różnym zagęszczeniu gruntu. Określono efekt skali jako stosunek wartości tarcia mobilizowanego na modelu do tarcia...
-
On shear correction factors in the non-linear theory of elastic shells
PublikacjaW pracy wyprowadzono analitycznie wartości korekcyjnych współczynników ścinania dla ścinania poprzecznego oraz dla momentów owinięcia w ramach nieliniowej sześcioparametrowej teorii powłok. Wartości wyprowadzono poprzez odpowiednie sformułowanie komplementarnej energii sprężystej. Na drodze analizy przy pomocy MES, badano wpływ wartości współczynników na położenie punktów bifurkacji, deformacje, całkowitą energię sprężystą układu...
-
FE-analysis of contractant shear zones in loose granular materials
PublikacjaW artykule przedstawiono wyniki numerycznej analizy stref ścinania w materiałach granulowanych luźnych. Obliczenia wykonano dla 4 różnych problemów brzegowych: ścinania warstwy między dwoma bardzo szorstkimi ścianami, ściskania w płaskim stanie odkształcenia, dwuosiowego ściskania, odporu na ściankę. Obliczenia wykonano stosując metodę elementów skończonych na bazie mikropolarnego prawa hipoplastycznego.
-
Discrete analysis of micro-structural events in granular shear zones
PublikacjaW artykule pokazano rozwój różnych zjawisk mikrostrukturalnych na poziomie ziarna podczas parcia pasywnego piasku na sztywną ściankę przemieszczającą się poziomo. Obliczenia wykonano stosując metodę DEM. Wyniki na poziomie globalnym porównano z wynikami MES. Szczególna uwagę zwrócono na rozwój łańcuchów sił miedzy ziarnami.
-
Study of some micro-structural phenomena in granular shear zones
PublikacjaW artykule pokazano wyniki dyskretne zachowania się ziaren materiałów granulowanych w strefie ścinania uzyskane metodą DEM. Wyniki porównano z wynikami MES na bazie mikropolarnego hipoplastycznego prawa konstytutywnego. Szczególną uwagę zwrócono w obliczeniach na zjawiska mikrostrukturalne w strefie ścinania takie jak: wiry, łańcuchy sił, lokalne zmiany porowatości.
-
Discrete simulations of shear zone pattern in earth pressure problems
PublikacjaW artykule przedstawiono wyniki dyskretnych symulacji naporu piasku na ściankę szczelną. Obliczenia wykonano stosując metodę elementów dyskretnych z kulami uwzględnieniem momentów kontaktu. Wyniki symulacji numerycznych porównano z wynikami doświadczalnymi.
-
Evolution of shear localisation in earth pressure problems of a retaining wall
PublikacjaPrzedstawiono wyniki numerycznej analizy formacji stref ścinania w materiale sypkim podczas problemów parcia i odporu gruntu za ścianą oporową. Zachowanie suchego piasku podczas testów ściskania w płaskim stanie odkształcenia było analizowane stosując metodę elementów skończonych i mikropolarne hypoplastyczne prawo konstytutywne. Podczas obliczeń numerycznych zwrócono szczególną uwagę na wpływ różnych przemieszczeń ściany na lokalizację...
-
Effect of boundary conditions in shear testers on properties of bulk solids.
PublikacjaPrzedstawiono wpływ warunków brzegowych w dwóch różnych aparatach ścinania na wielkość odkształceń i naprężeń. Obliczenia wykonano przy zastosowaniu metody elementów skończonych i mikropolarnego prawa hipoplastycznego.
-
Numerical modeling of shear localizations during granular flow in silos.
PublikacjaW artykule przedstawiono wyniki numerycznej analizy MES dotyczącej przepływów materiałów sypkich w silosach. Omówiono różne metody opisu lokalizacji odkształceń stycznych wewnątrz materiałów. Wyniki porónano z wynikami doświadczalnymi.
-
FE-analysis of shearing of granular bodies in a direct shear box
PublikacjaW artykule przedstawiono wyniki numerycznej obszernej analizy testu bezpośredniego ścinania. w materiałach granulowanych. Obliczenia wykonano stosując metodę elementów skończonych i mikropolarne hipoplastyczne prawo konstytutywne. Analizę wykonano dla różnego poziomu obciażenia, długości charakterystycznej, wskaźnika porowatości, długości próbki W analizie uwzględniono lokalizacje odkształceń stycznych.
-
ANALYSIS OF THE IMPACT OF MASS FLOW EXTRACTION ON THE CHANGE OF PARAMETERS IN A LABYRINTH SEAL USING THE STODOLA METHOD
PublikacjaLabyrinth seals are an important element of a steam turbine set design. The use of diagnostic extraction makes it possible to control the operation of a seal by providing information on the thermodynamic parameters along the length of the seal. Diagnostic extraction has a considerable impact on the change of the parameters, the amount of the extracted mass. This article describes the dependence of pressure in the clearance downstream...
-
ANALYSIS OF THE IMPACT OF MASS FLOW EXTRACTION ON THE CHANGE OF PARAMETERS IN A LABYRINTH SEAL USING THE STODOLA METHOD
PublikacjaLabyrinth seals are an important element of a steam turbine set design. The use of diagnostic extraction makes it possible to control the operation of a seal by providing information on the thermodynamic parameters along the length of the seal. Diagnostic extraction has a considerable impact on the change of the parameters, the amount of the extracted mass. This article describes the dependence of pressure in the clearance downstream...
-
Controlled Random Search Applied to Parameters Estimation of the Longitudinal Solutes Transport Model for Rivers
PublikacjaNumerical computations are presented for the longitudinal transport of passive, conservative solutes in an actual river with the inclusion of geometrical complexities of river channels. A special emphasis is put on the method of the identification of model parameters which is based on a specially designed optimisation procedure using random control search algorithm. Two different situations are considered namely a linear version...
-
A method of determining and visualizing safe motion parameters of a ship navigating in restricted waters
PublikacjaThe paper presents a method of displaying ship collision avoidance information which is based on an unconventional Collision Threat Parameters Area (CTPA) technique. The solution presented here extends CTPA's functionality from past works by supporting navigation in restricted waters and handling ship domains analytically instead of numerically. It visualizes potential navigational threats as well as possible collision avoidance...
-
A simplified behavioral MOSFET model based on parameters extraction for circuit simulations.
PublikacjaThe paper presents results on behavior modeling of general purpose Metal-Oxide Semiconductor Field-Effect Transistor (MOSFET) for simulation of power electronics systems requiring accuracy both in steady-state and in switching conditions. Methods of parameters extraction including nonlinearity of parasitic capacitances and steady-state characteristics are based on manufacturer data sheet and externally measurable characteristics....
-
Development and evaluation of thermosensitive hydrogels with binary mixture of Scutellariae baicalensis radix extract and chitosan for periodontal diseases treatment.
PublikacjaScutellaria baicalensis root displays anti-inflammatory and antibacterial properties due to the presence of flavonoids, particularly baicalin, baicalein, and wogonin. Our work aimed at developing thermosensitive hydrogels containing a binary mixture of S. baicalensis radix lyophilized extract and chitosan as a novel approach for periodontal diseases treatment....
-
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry - How to apply optical technologies in the diagnosis of reinforced concrete elements?
PublikacjaThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry
PublikacjaThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
Force transfer and stress distribution in short cantilever deep beams loaded throughout the depth with a various reinforcement
PublikacjaDeep beams used as the main reinforced concrete structural elements which taking over the load and stiffening construction are often found in high-rise buildings. The architecture of these buildings is sometimes sophisticated and varied, arouse the admiration of the majority of recipients, and thus causing an engineering challenge to correctly design the structural system and force transfer. In such structures is important to shape...
-
Ground tire rubber thermo-mechanically devulcanized in the presence of waste engine oil as asphalt modifier
PublikacjaCross-linked elastomers network is main limitation for industrial usage of ground tire rubber (GTR) as asphalts’ and road pavements modifier. GTR was thermo-mechanically devulcanized via extrusion in the presence of waste engine oil (WEO) at temperature ranges from 150 to 280 °C. Combined impact of WEO content and extruder barrel temperature on the change of cross-linked structure of degraded GTR (DTGR) was investigated through...
-
A Generalized Framework Towards Structural Mechanics of Three-layered Composite Structures
PublikacjaThree-layered composite structures find a broad application. Increasingly, composites are being used whose layer thicknesses and material properties diverge strongly. In the perspective of structural mechanics, classical approaches to analysis fail at such extraordinary composites. Therefore, emphasis of the present approach is on arbitrary transverse shear rigidities and structural thicknesses of the individual layers. Therewith...
-
Development and validation of lumbar spine finite element model
PublikacjaThe functional biomechanics of the lumbar spine have been better understood by finite element method (FEM) simulations. However, there are still areas where the behavior of soft tissues can be better modeled or described in a different way. The purpose of this research is to develop and validate a lumbar spine section intended for biomechanical research. A FE model of the 50th percentile adult male (AM) Total Human Model for Safety...
-
Designing of Parking Spaces on Parking Taking into Account the Parameters of Design Vehicles
PublikacjaNowadays, in all cities, there is an acute problem of a lack of parking spaces. The number of vehicles is constantly increasing not only in big cities and megacities, but also in small towns of the country, and there are not enough parking places—the pace of solving the problem is several times slower than the growth rate of transport among citizens. The paper is dedicated to the determination of an optimal size of a parking place...
-
SPECTRAL-BASED MODAL PARAMETERS IDENTIFICATION WITH MULTIPLE PARTICLE SWARMS OPTIMIZATION
PublikacjaThe paper presents usage of a Particle Swarm Optimization [1] based algorithm for spectral-based modal parameters identification. The main algorithm consists of two groups of swarms, namely, scouts and helpers. For the first group additional penalizing process is provided to force separation of scouting swarms in frequency space. The swarms have an ability to communicate with each other. At first stage, each swarm focuses on a...
-
The content of biogenic amines in Rondo and Zweigelt wines and correlations between selected wine parameters
PublikacjaThe purpose of this study was to evaluate the content of biogenic amines (BAs) in wines using dispersive liquid–liquid microextraction–gas chromatography–mass spectrometry (DLLME-GC–MS). An additional objective was to assess the correlations between selected parameters characterizing the samples such as the content of BAs, sugars, and organic acids, pH, and total acidity. Wines produced from the same grape variety in which alcoholic...
-
Analysis of the relationship between the length of eye fixation and the parameters of advertisements visible from the road
PublikacjaIn Poland, many advertising signs addressed to motorists are located along the roadside. Advertisements do not serve any traffic related purpose and can distract drivers making them less reliable and as a consequence, reduce road safety. The existing regulations only apply to the carriageway. The research is conducted as part of the RID project. The objective of the RID project is to create a "Manual for positioning roadside advertising...
-
Modeling and Strength Calculations of Parts Made Using 3D Printing Technology and Mounted in a Custom-Made Lower Limb Exoskeleton
PublikacjaThis study is focused on the application of 3D-printed elements and conventional elements to create a prototype of a custom-made exoskeleton for lower limb rehabilitation. The 3D-printed elements were produced by using Fused Deposition Modeling technology and acrylonitrile butadiene styrene (ABS) material. The scope of this work involved the design and construction of an exoskeleton, experimental testing of the ABS material and...
-
STRENGTH OF MATERIALS
Czasopisma -
Effect of temperature and ionic strength on volumetric and acoustic properties of solutions of urea alkil derivatives in aqueous NaCl
PublikacjaThe present work was undertaken to study volumetric and acoustic properties for diluted solutions of tetramethylurea in pure water and for urea, n-propylurea, n-butylurea and tetramethylurea in 0.5 or 1 moldm3 aqueous solutions of sodium chloride. This paper presents measured values of densities and sound velocities at T = (288.15, 298.15 and 308.15) K. From these data the apparent molar volumes, , adiabatic compressibilities,...
-
Influence of silver-core gold-shell nanoparticle parameters on the variation of surface-enhanced Raman spectra
PublikacjaThe detection of molecules by surface-enhanced Raman spectroscopy (SERS) is dependent on the nanomaterial used to induce the enhancement effect. This depends on a variety of parameters of the substrate such as the metal used for their creation, their shape, size and size distribution, concentration, as well as the parameters of the solution, such as packing of the nanoparticles, the complexity of the sample, the solvent, etc. It...
-
Heuristic Method of Safe Manoeuvre Selection Based on Collision Threat Parameters Areas
PublikacjaThis paper is a continuation of papers dedicated to a radar-based CTPA (Collision Threat Parameters Area) display designed to support safe manoeuvre selection. The display visualizes all the ships in an encounter and presents situational overview from the own ship’s point of view. It calculates and displays information on unsafe or unrealistic own ship’s course & speed allowing a user to select a safe manoeuvre. So far only the...
-
Combined analysis of whole human blood parameters by Raman spectroscopy and spectral-domain low-coherence interferometry
PublikacjaIn this article the simultaneous investigation of blood parameters by complementary optical methods, Raman spectroscopy and spectral-domain low-coherence interferometry, is presented. Thus, the mutual relationship between chemical and physical properties may be investigated, because low-coherence interferometry measures optical properties of the investigated object, while Raman spectroscopy gives information about its molecular...
-
ANALYSIS OF IMPACT of SHIP model parameters on changes of control quality index in ship dynamic positioning system
PublikacjaIn this work there is presented an analysis of impact of ship model parameters on changes of control quality index in a ship dynamic positioning system designed with the use of a backstepping adaptive controller. Assessment of the impact of ship model parameters was performed on the basis of Pareto-Lorentz curves and ABC method in order to determine sets of the parameters which have either crucial, moderate or low impact on objective...