wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: COMPARISON
-
Experimental study of boiling heat transfer in the stagnation point of water microjet
PublikacjaIn the paper presented is a comparison of computational model with experimental data. Numerical model of liquid film with phase change in the stagnation zone due to impingement of the microjet is more widely presented in authors previous work. The radius on which theevaporation process is taking place can be determined from the energy balance on the element of the plate. That radius has also been confirmed experimentally in the...
-
Coupled-Resonator Waveguide Filter in Quadruplet Topology With Frequency-Dependent Coupling - A Design Based on Coupling Matrix
PublikacjaThis letter presents an application of a recently developed coupling matrix synthesis technique to design of coupled-resonator filters with dispersive inter-resonator couplings. This technique is used to design a novel coupled-cavity bandpass filter. Measurements validate the design and confirm effectiveness of the synthesis method. The filter is a four-pole generalized Chebyshev filter with three transmission zeros. Resonators...
-
Performance Evaluation of Preemption Algorithms in MPLS Networks
PublikacjaPreemption is a traffic engineering technique in Multiprotocol Switching Networks that enables creation of high priority paths when there is not enough free bandwidth left on the route. Challenging part of any preemption method is to select the best set of paths for removal. Several heuristic methods are available but no wider comparison had been published before. In this paper, we discuss the dilemmas in implementing preemption...
-
The Reactivity of the Imine Bond within Polynuclear Nickel(II) Complexes
PublikacjaThree novel Ni complexes with the Schiff base ligand 2-methoxy-6-(E-2-pyridyliminomethyl)-phenol (L1) are described. In comparison with the similar 2-(pyridine-2-ylimino-methyl)phenol (pymp), the mode of coordination of L1 is altered due to the presence of methoxy substituent introducing the sterical hindrance. During the synthesis of the complexes, partial hydrolysis of the ligand was observed. Since such immediate hydrolysis...
-
Detection of damages in a rivetted plate
PublikacjaThe paper presents the results of damage detection in a riveted aluminium plate. The detection method has been based on Lamb wave propagation. The plate has been analysed numerically and experimentally. Numerical calculations have been carried out by the use of the time-domain spectral finite element method, while for the experimental analysis laser scanning Doppler vibrometry (LSDV) has been utilised. The panel has been excited...
-
Deep Learning-Based LOS and NLOS Identification in Wireless Body Area Networks
PublikacjaIn this article, the usage of deep learning (DL) in ultra-wideband (UWB) Wireless Body Area Networks (WBANs) is presented. The developed approach, using channel impulse response, allows higher efficiency in identifying the direct visibility conditions between nodes in off-body communication with comparison to the methods described in the literature. The effectiveness of the proposed deep feedforward neural network was checked on...
-
Immunosuppressive properties of amino acid and peptide derivatives of mycophenolic acid
PublikacjaMycophenolic acid (MPA) was coupled with amino acids and biologically active peptides including derivatives of tuftsin to modify its immunosuppressive properties. Both amino acid unit in the case of simple MPA amides and modifications within peptide moiety of MPA - tuftsin conjugates influenced the observed activity. Antiproliferative potential of the obtained conjugates was investigated in vitro and MPA amides with threonine methyl...
-
Taq DNA polymerase fused with DNA binding protein with increased resistance to inhibitors from clinical samples
PublikacjaNowadays PCR method is commonly used in molecular diagnostic. However, in many cases PCR is limited, by the presence of inhibitory substances in biological, soil or food samples Efficiency and fidelity of amplification is strongly connected with DNA polymerase and reaction conditions. To meet the requirements of modern diagnostic methods it is essential to seeking for new DNA polymerases with better properties useful in these field....
-
Mobile satellite measurements on the Pomeranian Metropolitan Railway
PublikacjaThis paper presents the process of organization and execution of the mobile satellite measurements conducted on the tracks of the Pomeranian Metropolitan Railway before officially entry the line into operation. These measurements allowed for the accurate identification of the actual geometric shape of the line. In the paper the issues of both design and construction phase of this railway line has been described. Moreover, the geodetic...
-
Application of the ‘CPT 2012’model of AFNOR standard for column design in Poland–Jazowa case study
Publikacjahis paper presents the ‘CPT 2012’ model incorporated into the AFNOR NF P94-262:2012-07, French standard for pile design fully compatible with Eurocode 7, to the wider Polish audience. The bearing capacity of three reference columns for Vistula Marshlands have been calculated according to ‘CPT 2012’ model and AFNOR recommendations. Then, the design resistances have been compared with ultimate column bearing capacity measured during...
-
Fabrication, structural and electrical properties of Sr(V,Nb)O 3-δ perovskite materials
PublikacjaThe SrV1-xNbxO3-δ materials with different niobium content in perovskite B-sublattice were prepared by a solid-state reaction process. The microstructure and phase compositions of obtained samples were analyzed by the X-ray diffraction technique (XRD) and scanning electron microscopy (SEM). The electrical conductivity of samples was measured by a DC 4-wire method in range of 100–600 °C in different gas conditions. The oxidation...
-
Improving all-reduce collective operations for imbalanced process arrival patterns
PublikacjaTwo new algorithms for the all-reduce operation optimized for imbalanced process arrival patterns (PAPs) are presented: (1) sorted linear tree, (2) pre-reduced ring as well as a new way of online PAP detection, including process arrival time estimations, and their distribution between cooperating processes was introduced. The idea, pseudo-code, implementation details, benchmark for performance evaluation and a real case example...
-
Towards Audio Signal Equalization Based on Spectral Characteristics of a Listening Room and Music Content Reproduced
PublikacjaThis study presents investigations of the influence of the room acoustics on the frequency characteristic of the audio signal playback. First, the concept of a novel spectral equalization method of the room acoustic conditions is introduced. On the basis of the room spectral response, a system for room acoustics compensation based on an equalizer designed is proposed. The system settings depend on music genre recognized automatically....
-
Design optimization of novel compact circular polarization antenna
PublikacjaThe paper describes a structure and a design optimization procedure of a miniaturized circular polarization antenna with elliptical ground plane slots and feed line with stepped-impedance stubs. Constrained optimization of all antenna parameters is executed in order to explicitly reduce the antenna size while maintaining required impedance axial ratio bandwidth of 5 GHz to 7 GHz at the same time. The size of the optimized antenna...
-
Investigation of educational processes with affective computing methods
PublikacjaThis paper concerns the monitoring of educational processes with the use of new technologies for the recognition of human emotions. This paper summarizes results from three experiments, aimed at the validation of applying emotion recognition to e-learning. An analysis of the experiments’ executions provides an evaluation of the emotion elicitation methods used to monitor learners. The comparison of affect recognition algorithms...
-
COMPARATIVE STUDY OF TRADITIONAL AND VIRTUAL TEAMS
PublikacjaThe paper presents two kinds of cooperating teams: traditional and virtual, and proposes a new measure of the team virtuality level. Some representative teamwork characteristics, such as team member competencies, team diversity, leadership, and team decision-making are analyzed and compared depending on the degree of virtuality. Moreover, the team climate as one of the team performance measures is also analyzed and compared in...
-
Identification of Bodner-Partom Viscoplastic Model Parameters for Some Aluminum Alloys at Elevated Temperature
PublikacjaThe paper presents the identification process of inelastic (viscoplastic) properties for two aluminum alloys at a temperature of 120°C. The material parameters are calculated on the basis of uniaxial tension tests. Twelve tests at elevated temperature for each alloy have been performed—three tests for four different strain rates. The main purpose of the paper is to identify the Bodner-Partom viscoplastic model parameters for two...
-
RECSYS CHALLENGE 2015: a BUY EVENT PREDICTION IN THE E-COMMERCE DOMAIN
PublikacjaIn this paper we present our approach to RecSys Challenge 2015. Given a set of e-commerce events, the task is to predict whether a user will buy something in the current session and, if yes, which of the item will be bought. We show that the data preparation and enrichment are very important in finding the solution for the challenge and that simple ideas and intuitions could lead to satisfactory results. We also show that simple...
-
An odor-sensing system - powerful technique for foodstuff studies
PublikacjaThis work examines gas sensor array technology combined with multivariate data processing methods and demonstrates a promising potential for rapid, non-destructive analysis of food. Main attention is focused on detailed description of sensor used in e-nose instruments, construction, and principle of operation of these systems. Moreover, this paper briefly reviews the progress in the field of artificial olfaction and future trends...
-
Processing, mechanical and thermal behavior assessments of polycaprolactone/agricultural wastes biocomposites
PublikacjaIn this paper, brewer’s spent grain (BSG) was applied as potential lignocellulose biofiller in biocompos-ites based on polycaprolactone (PCL). The PCL/BSG biocomposites filled with varying content of biofillerswere prepared via low-temperature melt-compounding. These conditions allow limiting thermal degra-dation of used biofillers during processing. The influence of biofiller content (ranging from 25 to 200parts by weight on 100...
-
The Course and the Effects of Agricultural Biomass Pyrolysis in the Production of High-Calorific Biochar
PublikacjaThe thermal pyrolysis of agriculture biomass has been studied in a fixed-bed reactor, wherethe pyrolysis was conducted at a steady temperature of 800◦C. This work analyses the pyrolysisproducts of six agricultural wastes: pistachio husks, walnut husks, sunflower hulls, buckwheat husks,corncobs and coconut shells. The conducted research compared examples of large waste biomassstreams from different parts of the world as a potential...
-
Shape-controllable synthesis of GdVO4 photocatalysts and their tunable properties in photocatalytic hydrogen generation
PublikacjaNovel visible light responsive materials for water splitting are essential for the efficient conversion of solar energy into hydrogen bond energy. Among other semiconductors, gadolinium orthovanadate has appropriate conduction and valence band edges positioned to split water molecules and a narrow band gap that allows the use of visible light for hydrogen generation. Thus, we present here that hydrogen evolution under visible light...
-
Three-dimensional numerical investigation of hybrid nanofluids in chain microchannel under electrohydrodynamic actuator
PublikacjaEnergy efficiency enhancement methods have received considerable attentionwithin the industry and scientific community, owing to the rising concern ofglobal energy sustainability. The present article attempts to scrutinize the effectsof electrohydrodynamics and nanofluids on the rate of heat transfer and fluidflow in the 3-D chain microchannels. Improved heat exchangers (e.g., chainmicrochannel) would have a key role in increasing...
-
Botanical and geographical origin characterization of polish honeys by headspace SPME-GCxGC-TOFMS
PublikacjaVolatile organic compounds (VOCs) composition of Polish honeys obtained from various geographical regions was studied. Headspace solid phase microextraction (HS-SPME) using Divinylbenzene/Carboxen/Polydimethylsiloxane-coated fibers was used in combination with comprehensive two-dimensional gas chromatography-time-of-flight mass spectrometry (GC× GC-TOFMS) because of the complexity of the samples. Acacia, linden, rapeseed, buckwheat...
-
Characterization of Arctic Driftwood as Naturally Modified Material. Part 1: Machinability
PublikacjaArctic driftwood has reached the coast of Iceland for centuries. This material was used by the inhabitants of the island as a building material for houses, boats, churches and pasture fences. Nowadays, the driftwood is used in the furniture industry, for the finishing of internal and external walls of buildings and also by artists. The properties of driftwood differ to that of original resource due the long-term effects of exposure...
-
Mechanical Properties of Bio-Composites Based on Epoxy Resin and Nanocellulose Fibres
PublikacjaThe aim of our research was to investigate the effect of a small nanocellulose (NC) addition on an improvement of the mechanical properties of epoxy composites. A procedure of chemical extraction from pressed lignin was used to obtain nanocellulose fibers. The presence of nanoparticles in the cellulose pulp was confirmed by FTIR/ATR spectra as well as measurement of nanocellulose particle size using a Zetasizer analyzer. Epoxy...
-
Application of Electronic Nose Based on Fast GC for Authenticity Assessment of Polish Homemade Liqueurs Called Nalewka
PublikacjaThe possibility of application of electronic nose based on fast GC for differentiation of three types of cherry liqueurs, namely Polish homemade liqueurs called nalewka, commercially available liqueurs labeled as nalewka, and commercial liqueurs, was investigated. This device was equipped with two parallel connected columns with different stationary phases coupled to two ultrasensitive flame ionization detectors (μ-FIDs). Four...
-
Potrzeba wykorzystania narzędzi Enterprise Project Management w przedsiębiorstwie między narodowym - studium przypadku
PublikacjaW artykule przedstawiono wyniki badań dotyczące projektu wdrożenia narzędzia informatycznego, które usprawni proces planowanie pracy i zarządzanie zasobami w filiach zagranicznych, mającego znamiona systemu Enterprise Project Management - do wspomagania zarządzania projektami. Omówiono zalety oraz wady tego typu rozwiązań w stosunku do tradycyjnych sposobów zarządzania. Wskazano szanse i zagrożenia dla rozwoju przedsiębiorstw wynikające...
-
LLA : A New Anypath Routing Scheme Providing Long Path Lifetime in VANETs
PublikacjaVehicular ad-hoc networks (VANETs) are a promising solution to improve the road traffic safety, reduce the environmental pollution, or simply provide the on-board infotainment services. However, these actions are often not possible due to high mobility of vehicles causing frequent failures of VANET links. In this paper, we focus on anypath routing to improve the reliability of multihop VANET communications. In particular, the paper...
-
Efficiency of Wastewater Treatment in Single-Family Constructed Wetlands in Kaszuby Lake District
PublikacjaIn the paper results of investigation upon three different configurations of single family treatment wetlands were presented. It was indicated that the application of treatment wetlands for single family effluent is a effective and sustainable solution for wastewater treatment in the rural areas. In spite of the receiving higher concentration of pollutants in comparison to the TWs operated in Europe and USA analysed TWs ensure...
-
Red Algae – An Alternative Source of Carbon Material for Energy Storage Application
PublikacjaNew electrode material obtained by pyrolysis of aquatic biomass macro (red algae) soaked with glucose solution has been characterized by SEM, EDX and Raman spectroscopy. Graphitized carbon was identified by Raman spectroscopy. Galvanostatic cyclic polarization of the materials in contact with 1M LiPF6 electrolyte in EC:DMC (1:1 v/v) and Li as a counter electrode was performed. Specific capacity of the novel material was enhanced...
-
Stability and limit load analysis of a cold-formed channel section column
PublikacjaThe paper presents stability and limit load analysis of a steel column 1440 mm high of a cold-formed channel section, subjected to a combination of compression and bending. Experimental results were compared to the resistance of a code procedure and to the outcome of numerical non-linear analysis. Comparison was made of numerical solutions by means of static (Riks) and dynamic (Explicit and Implicit) methods. Perfectly elastic...
-
Mechanical properties of PVDF-coated fabric under tensile tests
PublikacjaThis article describes the laboratory tests necessary to identify the mechanical properties of the polyvinylidene fluoride (PVDF)-coated fabrics named Precontraint 1202S and Precontraint 1302S. First, a short survey of the literature concerning the description of coated woven fabrics is presented. Second, the material parameters for PVDF-coated fabrics are specified on the basis of biaxial tensile tests. A comparison of the 1:1...
-
Use of Sensory Analysis Methods to Evaluate the Odor of Food and Outside Air
PublikacjaSensory analysis is applied in many areas of daily life. It is used to carry out the sensory evaluation of foodstuffs or other products and to evaluate the properties of odors present in the environment. The authors attempt to summarize the knowledge on the classification and application of sensory analysis methods to evaluate the odor nuisance of air, which allows the identification of sensory impressions and determination of...
-
Control design for slow speed positioning
PublikacjaThe problem under study is a synthesis of position and heading control system for low frequency model of surface vessel described by 3 DOF mathematical model. The recursive vectorial backstepping control design was used to keep fixed position and heading in presence of wave disturbances. The controller has been simulated on computer model of scaled supply vessel. It has been assumed that the actuators produce generalized forces...
-
Improvement of Fingerprinting Method based on Hill Cipher by using Frequency Domain
PublikacjaThe main goal of this paper is to present the advantages of a digital fingerprinting in a frequency domain over a pixel domain, in case of VoD services (Video on Demand). The paper presents basic issues of a multimedia data protection by digital fingerprinting. It also describes threats to embedded fingerprints from both collusion attacks and from a transmission itself. Possible solution was presented on the example of the DCT...
-
Polyarmonic model of synchronous generator for analysis of autonomous power generation systems
PublikacjaAbstract: This paper presents the polyharmonic modelling of synchronous generator (SG) in machine variables. The simple geometry and windings physical layout has been used for inductance calculations of a salient-pole SG. The main advantage of this model is the ease of describing an autonomous power generation system (APGS) in terms of its topology and thus providing effective analysis at the static and dynamic states, both for...
-
rigid polyurethane foams modified with selected nanofillers
PublikacjaThe nanofillers: natural montmoryllonite (MMT) - Bentonite, natural MMT modified with a quaternary ammonium salt - Cloisite30B, has been used in rigid polyurethane foams (PUFs). The influence of fillers amounts on processing parameters, physical-mechanical properties (density, water absorption, brittleness and compression strength) and thermal properties (thermal stability, fire behaviours) of such foams has been analysed. The...
-
The role and importance of WIMAX mobile system as a high-performance data transfer technology in wireless sensor networks for wide area monitoring applications
PublikacjaThe study discuses basic features and functional design of WiMAX Mobile system, based on the IEEE 802.16e (Release 1.5 Rev. 2.0) standard. The analysis has been made in terms of ability to use this system to transmit video stream related to monitoringof large agglomeration areas. What is more, the study includes comparison of technical parameters of WiMAX Mobile system with competitive systems such as: HSPA+ and UMTS-LTE, which...
-
New Alternative Passive Networks to Improve the Range Output Voltage Regulation of the PWM Inverters
PublikacjaThis paper presents different topologies of buck-boost converters with passive input networks that have alternative topologies; this is known in the literature as a Z-source inverter. Alternative passive networks were named by the authors as T-inverters; these improve output voltage regulation of the PWM inverters. T-inverter has fewer reactive components in comparison to conventional Z-source inverter. The most significant advantage...
-
Crack Mouth Opening Displacement for EH36 Shipbuilding Steel Measurements
PublikacjaThe dataset titled EH36 steel for shipbuilding (plate thicnkness 50mm) - CMOD - force record, a0/W = 0.6 contains CMOD (Crack Mouth Opening Displacement) - Force record which is the base for evaluation of fracture toughness of structural steel. Bend specimens witch Bx2B section (B= 50mm), and relative initial crack length a0 / W = 0.60 were used. The test was carried out at ambient temperature in accordance to ISO 12135 standard....
-
In situ transformation boosts the pseudocapacitance of CuNi-MOF via cooperative orientational and electronic governing
PublikacjaThe disordered arrangement and thereof inferior conductivity of 2D MOF sheets seriously hinder their practical application. Herein, we propose in situ transformation strategy to architect vertically oriented bimetallic CuNi-MOF as a self-supporting electrode, leading to a decuple high specific capacitance of 1262 C g-1 in comparison with the pristine Ni-MOF powder of 114 C g-1 at 2 A g-1. DFT calculations reveal that introduction...
-
Stress Detection of Children With ASD Using Physiological Signals
PublikacjaThis paper proposes a physiological signal-based stress detection approach for children with autism spectrum disorder (ASD) to be used in social and assistive robot inter- vention. Electrodermal activity (EDA) and blood volume pulse (BVP) signals are collected with an E4 smart wristband from children with ASD in different countries. The peak count and signal amplitude features are derived from EDA signal and used in order to detect...
-
Comparative analysis of numerical with optical soliton solutions of stochastic Gross–Pitaevskii equation in dispersive media
PublikacjaThis article deals with the stochastic Gross–Pitaevskii equation (SGPE) perturbed with multiplicative time noise. The numerical solutions of the governing model are carried out with the proposed stochastic non-standard finite difference (SNSFD) scheme. The stability of the scheme is proved by using the Von-Neumann criteria and the consistency is shown in the mean square sense. To seek exact solutions, we applied the Sardar subequation...
-
MRAS-Based Switching Linear Feedback Strategy for Sensorless Speed Control of Induction Motor Drives
PublikacjaThis paper presents a newly designed switching linear feedback structure of sliding mode control (SLF-SMC) plugged with an model reference adaptive system (MRAS) based sensorless fieldoriented control (SFOC) for induction motor (IM). Indeed, the performance of the MRAS depends mainly on the operating point and the parametric variation of the IM. Hence, the sliding mode control (SMC) could be considered a good control alternative...
-
Application of Fast Cameras to String Vibrations Recording
PublikacjaA hardware and software solution for guitar string vibration measurement by fast cameras is described. Orthogonal setup for 3D image acquisition is proposed capable to capture several thousand image frames per second. Dedicated image processing algorithm was developed and described in the paper, aimed at tracking the movement of some selected points along the string. Fast and accurate tracking results provided a detailed information...
-
Investigations of the optical activity of nonlinear crystals by means of dual-wavelength polarimeter
PublikacjaA dual-wavelength method in high accuracy polarimetry has been successfully tested and applied to measure optical activity (OA) of nonlinear crystals. In proposed polarimetric scheme two neighboring semiconductor laser wavelengths (635 and 650 nm) are used, which increases number of parameters measured simultaneously and improves the data processing. By neglecting dispersion of eigen wave ellipticity in crystals, more efficient...
-
Modelling of Objects Behaviour for Their Re-identification in Multi-camera Surveillance System Employing Particle Filters and Flow Graphs
PublikacjaAn extension of the re-identification method of modeling objects behavior in muti-camera surveillance systems, related to adding a particle filter to the decision-making algorithm is covered by the paper. A variety of tracking methods related to a single FOV (Field of Vision) are known, proven to be quite different for inter-camera tracking, especially in case of non-overlapping FOVs. The re-identification methods refer to the...
-
Electromagnetic plane wave scattering from a cylindrical object with an arbitrary cross section using a hybrid technique
PublikacjaA hybrid technique combining finite-element and mode-matching methods for the analysis of scattering problems in open and closed areas is presented. The main idea of the analysis is based on the utilization of the finite-element method to calculate the post impedance matrix and combine it with external excitation. The discrete analysis, which is the most time- and memory-consuming, is limited here only to the close proximity of...
-
The QDMC Model Predictive Controller for the Nuclear Power Plant Steam Turbine Control
PublikacjaThere are typically two main control loops with PI con trollers operating at each turbo-generator set. In this paper a model predictive controller QDMC for the steam turbine is proposed - instead of a typical PI controller. The QDMC controller utilize a step-response model for the controlled system. This model parameters are determined, based on the simplified and linear model of turbo-generator set, which parameters are identified...