Wyszukiwarka
Filtry
wszystkich: 1736
-
Katalog
- Publikacje 1302 wyników po odfiltrowaniu
- Czasopisma 29 wyników po odfiltrowaniu
- Konferencje 1 wyników po odfiltrowaniu
- Osoby 18 wyników po odfiltrowaniu
- Projekty 1 wyników po odfiltrowaniu
- Kursy Online 21 wyników po odfiltrowaniu
- Wydarzenia 4 wyników po odfiltrowaniu
- Dane Badawcze 360 wyników po odfiltrowaniu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: tandem mass spectrometry
-
LCT, PIV and IR Imaging Detection in Selected Technical and Biomedical Applications
PublikacjaPaper presents the brief summary of the history of Thermochromic liquid crystals (TLC), Particle Image Velocimetry (PIV) and Infrared Imaging Themography (IR). Principal methods and tools are described and some examples are presented. With this objective, a new experimental technique have been developed and applied to the study of heat and mass transfer and for biomedical diagnosis. Selected results of experiments using these methods...
-
Compact satellite hydraulic unit
PublikacjaThe article describes the design and operation of a prototype hydraulic unit. It is based on an inversed kinematics, satellite pump in which the body rotates around the shaft. The pump is placed inside the electric motor. Thanks to that the compact and low mass construction was achieved. Thanks to new commutation unit with enlarged channels, lower pressure losses were obtained. The article presents the construction and results...
-
Degradation of modified TPS in natural and industrial compost
PublikacjaThe aim of the study was to determine in the pilot studies the degree of decomposition of modified by us thermoplasic starch (potato starch).Commercial and new obtained by us foils were tested in an open roofing at normal weather conditions. The most visible changes were observed in TPS modified by epoxidized soybean oil and arabic gum contrary to commercial foils where there was no mass change observed.
-
Kinetics of pollutants removal in hybrid treatment wetlands – Case study comparison
PublikacjaRecent years have seen an increasing interest in hybrid constructed wetland (HCW) systems for domestic sewage treatment. This paper is focused on kinetics of removal of the main pollutants occurring in wastewater i.e. organics expressed as chemical oxygen demand, biochemical oxygen demand and total nitrogen. The purpose of the article is to compare different HCW configurations in terms of mass removal rates (MRR) and removal rate...
-
Dynamic analysis of the railway bridge span under moving loads
PublikacjaThe first part of this paper provides a review of the state of knowledge of the dynamic behaviour of railway bridges under moving loads. Particular attention is paid to developments in modelling railway bridge loading and dynamic vehicle-span (structure) interaction. The most important aspects determining the advancements in this area of knowledge are identified. The contemporary techniques for defining bridge span finite element...
-
EXPERIENCE-ORIENTED SMART EMBEDDED SYSTEM
PublikacjaThe Experience-Oriented Smart Embedded System (EOSES) is proposed as a new technological platform providing a common knowledge management approach that allows mass embedded systems for experiential knowledge capturing, storage, involving, and sharing. Knowledge in the EOSES is represented as SOEKS, and organized as Decisional DNA. The platform is mainly based on conceptual principles from Embedded Systems and Knowledge Management....
-
Examination of Spectral Properties of Medicinal Plant Leaves Grown in Different Lighting Conditions Based on Mint Cultivation
PublikacjaCultivation in controlled environmental conditions can provide good quality medicinal herbs with consistent properties. A sensing system that can determine the contents of medicinal substances in plants using spectral characteristics of leaves would be a valuable tool. Viability of such sensing approach for mint had to be confirmed experimentally, as no data correlating contents of medicinal substances with spectral characteristics...
-
The Action Mechanisms, Anti-Cancer and Antibiotic-Modulation Potential of Vaccinium myrtillus L. Extract
PublikacjaHerbal medicinal products containing Vaccinium myrtillus L. (bilberry) fruits and fruit extracts are widely available in the market. Although bilberry leaves and stems are considered as bio-waste, they contain much higher levels of phenolic compounds than fruits. The study aimed to investigate the antimicrobial and anticancer potential of aerial part extracts from Vaccinium myrtillus L. (V. myrtillus, VM) plants harvested at high...
-
Badania nad rozdzielaniem grupowym i analityką składu grupowego olejów bazowych i smarowych, zwłaszcza o szerokim zakresie polarności składników
PublikacjaRozprawa to studia i badania nad rozdzielaniem i analityką składu grupowego olejów bazowych i smarowych o szerokim zakresie polarności składników. Studium literatury wykazało brak metodyk badania udziału frakcji naftowej i roślinnej w takich olejach oraz nieadekwatność w tym celu HPLC. Pierwsza część pracy to badania nad opracowaniem wielokrotnie zastosowanej w praktyce terenowej metodyki i wyposażenia dla zastosowania fluorescencji...
-
Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters
Dane BadawczeThe data set contains the simulation files related to the research paper “Numerical Study of the Impinging Jets Formed by an Injector with Different Nozzle Diameters”, https://doi.org/10.4271/2022-01-1080.
-
Functional properties of packaging materials from chemical modified stach.
PublikacjaThis work is focused on study of the mechanical and barrier properties of films obtained from potato starch modified with sodium tetrahydroxozincate generated in situ. The results show that the chemical modification of starch improved the water vapor permeability by about 25%, unfortunately decreased the elongation at break by 60%, when compared with unmodified starch films. However, placitization of films with glycerol at a concentration...
-
ThreSpect – A Program for the Determination of the Appearance Energies of Neutral and Ionized Species
PublikacjaCollisions of photons and charged particles with molecules lead to their excitation, ionization, and dissociation into neutral and ionized fragments. Accurately determining thresholds of the formation of particular products plays a vital role in analyzing processes occurring during these interactions. Therefore, we present a computer program, “ThreSpect,” that allows calculating threshold energies of various species generated in...
-
O możliwościach kształtowania właściwości dynamicznych konstrukcji kładek dla pieszych
PublikacjaW artykule przedstawiono doświadczenia własne autora związane ze „strojeniem” dynamicznym konstrukcji kładek dla pieszych. W celu potwierdzenia poprawności założeń przeprowadzono szereg złożonych analiz dynamicznych wykorzystujących nieliniowe procedury i modele. Opisano zrealizowane przykłady.
-
Modelowanie i symulacja ruchu pojazdu zabytkowego podczas hamowania
PublikacjaOpracowano model samochodu zabytkowego z wykorzystaniem metody masa-sprężyna, służącego do symulacji procesu hamowania pojazdu zabytkowego z możliwością pomiaru drogi hamowania. Konfiguracja sieci połączeń między punktami mas elementów zawieszenia oraz opony okazuje się mieć bardzo duży wpływ na zachowanie symulowanego samochodu podczas hamowania. Poprawność symulacji sprawdzono porównując wyniki uzyskane z symulacji oraz z pomiarów...
-
Application of quartz crystal microbalance and dynamic impedance spectroscopy to the study of copper corrosion inhibitors
PublikacjaThe study investigates the application of Dynamic Electrochemical Impedance Spectroscopy (DEIS) and Electrochemical Quartz Crystal Microbalance (EQCM) techniques to examine the corrosion inhibition of copper by Benzotriazole and Sodium Folate in a 0.1 M NaCl solution. DEIS, an advanced version of Electrochemical Impedance Spectroscopy (EIS), allows for real-time monitoring of non-stationary electrochemical systems,...
-
Thermo-Chemical Decomposition Study of Polyurethane Elastomer Through Glycerolysis Route with Using Crude and Refined Glycerine as a Transesterification Agent
PublikacjaDue to the increasing amount of polyurethane waste, chemical recycling of these materials is a topic of growing interest for many researchers. The primary pur- pose of polyurethane feedstock recycling is to recover the starting polyol. In this study glycerolysis using glycerine from two sources and two purity grades is proposed as a method of chemical recycling. The main effort of this paper focuses on the employment of commercial...
-
Automated Valuation Model based on fuzzy and rough set theory for real estate market with insufficient source data
PublikacjaObjective monitoring of the real estate value is a requirement to maintain balance, increase security and minimize the risk of a crisis in the financial and economic sector of every country. The valuation of real estate is usually considered from two points of view, i.e. individual valuation and mass appraisal. It is commonly believed that Automated Valuation Models (AVM) should be devoted to mass appraisal, which requires a large...
-
Influence of finishing colour on the efficiency of automated production line for wooden doors
PublikacjaPorta KMI Poland S.A. company has implemented a fully automated intelligent technological line TechnoPORTA for customized mass-production of technical door leaves. Each door leaf is provided with a unique QR code. It allows the line modules to individually adjust the machining parameters to the currently processed element according to the IT controlling system. Before en-tering the TechnoPorta line, the door leaves are not sorted,...
-
Bio‐polyols synthesized by liquefaction of cellulose: Influence of liquefaction solvent molecular weight
PublikacjaCurrently, the plastics industry including polyurethanes is based on the use of petrochemicals. For this reason, scientists are looking for new types of renewable resources for the substitution of petrochemical substances. This work aims to evaluate the effect of polyethylene glycols (PEG) with different molecular mass impact on properties of bio-based polyols synthesized via biomass liquefaction of cellulose. To date, research...
-
An advanced thermal-FSI approach of an evaporation of air heat pump
PublikacjaThe paper presents selected problems of numerical modeling of an advanced thermal-FSI approach of evaporator of air heat pomp. The example of a fin-tube evaporator has been studied, focusing on obtaining of heat exchanger characteristics applying two-phase flow model for the in-tube refrigerant flow. Special attention is given to heat transfer between separated medium for different air velocity and changed refrigerant mass flow...
-
Transparent thin films of Cu-TiO2 with visible light photocatalytic acitivity
PublikacjaThin films of Cu–TiO2 with a high level of transparency were prepared by a dip-coating procedure on the glass surface. CuCl2 was used as a copper precursor added during sol – gel synthesis of TiO2. The extension of optical absorption into the visible region of as-prepared thin films was indicated by UV/Vis spectroscopy. Only the anatase phase was detected by X-ray di ffraction analysis (XRD). The presence of copper in the structure...
-
Influence of Diosmin Treatment on the Level of Oxidative Stress Markers in Patients with Chronic Venous Insufficiency
PublikacjaOxidative stress plays an important role in the pathophysiology of many human disorders, while antioxidants prevent the development of various adverse symptoms. Diosmin is a natural flavonoid applied in vascular system disorders, especially in chronic venous insufficiency (CVI), and it plays a significant part in the alleviation of CVI symptoms. Due to antioxidant activity, it also has the ability to scavenge the oxygen free radicals...
-
The use of innovative application in creating new marketing space for cultural and entertainment events in the local market
PublikacjaThe following article describes the problems concerning marketing of mass events in the local market and potential solutions. In the first part the barriers that occur in communication between the organizers and the articipants are defined. In the process of identifying problems the results of research conducted for the needs article were used. In following sections the solution with use of Smartphone app is shown. The features that...
-
Homoisocitrate dehydrogenase from Candida albicans: properties, inhibition, and targeting by an antifungal pro-drug
PublikacjaThe LYS12 gene from Candida albicans, coding for homoisocitrate dehydrogenase was cloned and expressed as a His-tagged protein in Escherichia coli. The purified gene product catalyzes the Mg2+- and K+-dependent oxidative decarboxylation of homoisocitrate to alpha-ketoadipate. The recombinant enzyme demonstrates strict specificity for homoisocitrate. SDS-PAGE of CaHIcDH revealed its molecular mass of 42.6±1 kDa, while in size-exclusion...
-
Structure and properties of liquid Al–Cu alloys: Empirical potentials compared
PublikacjaWe report on the structure and mass transport properties of liquid Al–Cu alloys predicted by two recently-developed empirical many-body potentials: MEAM (Jelinek et al., 2012) and EAM-ADP (Apostol and Mishin, 2011), and by the well-known Gupta potential. Total and partial pair correlation functions, angular distribution functions, densities, coordination numbers and self-diffusion coefficients are compared with published experimental...
-
Stability Assessment of Coastal Cliffs Incorporating Laser Scanning Technology and a Numerical Analysis
PublikacjaWe investigated the cli coast in Jastrzebia Gora, Poland. The measurements that were taken between 2014 and 2018 by applying terrestrial, mobile, and airborne laser scanning describe a huge geometric modification involving dislocations in a 2.5 m range. Dierential maps and a volumetric change analysis made it possible to identify the most deformed cli’s location. Part of the monitoring of coastal change involved the measurement...
-
Polyurethane Glycerolysate as a Modifier of the Properties of Natural Rubber Mixtures and Vulcanizates
PublikacjaChemical recycling of polyurethanes can be realized in several different ways, but the most important methods are glycolysis and glycerolysis. Both methods permit recovery of polyols (when the process is realized with the mass excess of depolymerizing agent) or substitutes of polyols, which contain urethane moieties in the main chains and terminate mainly in hydroxyl groups (when the process is realized with the mass excess of...
-
Flow boiling intensification in minichannels by means of mechanical flow turbulising inserts
PublikacjaThe work presents the results of experimental investigation on heat transfer in minichannels. Refrigerant R123 was used as a test fluid. Single vertical silver tubes of 380 mm length and 2.3 mm diameter were examined with two variants of turbulising inserts. A wide range of parameters was considered, namely mass flux G=534-3011 kg/(m2s), heat flux qw=28.5-68.4 kW/m2, saturation temperature Tsat=23-86 stC and the full range of vapour...
-
An optimal designed experiment for the alkaline hydrolysis of feather keratin
PublikacjaFeathers, burdensome waste from the poultry industry, can be a cheap source of keratin, a protein with excellent physico- chemical, biological, and mechanical properties. Acid and alkaline hydrolyses are usually adopted for isolation of keratin from its natural resources. This study aimed at assessing the statistically significant effect of input variables in the alkaline hydrolysis of keratin from chicken feathers on the process...
-
Mobility Oriented Development (MOD): Public-Private Partnership in Urban Parking & Traffic Management with the Use of Autonomous Automobiles, Car-Sharing, Ridesharing Modes of Transport & Mobility as a Service (MaaS)
PublikacjaThe focus of the following research are relations between mobility technologies and metropolitan (urban and suburban) spatial structures. In this paper the author discusses various urban modes of transport (automobile, mass transit) in the context of emerging technical (autonomous vehicles, self-driving cars and driverless shuttles) and organizational (carpooling, ridesharing, car-sharing, on-demand mobility) solutions for " mobility...
-
Interactions of positrons with atoms and molecules
PublikacjaThe positron is the antiparticle of the electron. It has the same mass as the electron, but opposite charge. The understanding of the interactions of positrons with normal matter, like atoms and molecules, is of interest in various scientific fields, like nuclear medicine, plasma physics and astronomy. In this talk we will give a short introduction to some theoretical methods to describe the interactions of positrons with atoms...
-
Inauguracja Obchodów 30-lecia WZiE
WydarzeniaDnia 13.10.2022 r. o godz. 17.00 w Auli Politechniki Gdańskiej odbędzie się koncert Akademickiego Chóru PG oraz Polskiej Filharmonii Kameralnej w Sopocie pod batutą prof. Mariusza Mroza.
-
Seasonal changes of mercury speciation in the coastal sediments
PublikacjaPurpose Mercury speciation in sediments is linked to environmental conditions and processes. Domination of particular mercury species depends on its source, displays considerable seasonal behavior, and may be further modified due to oxygen levels, icing conditions, or the input of fresh organic matter. The purpose of this study was to examine the coastal area of the Gulf of Gdańsk in terms of mercury contamination and the influence...
-
Singular curves in the resultant thermomechanics of shells
PublikacjaSome geometric and kinematic relations associated with the curve moving on the shell base surface are discussed. The extended surface transport relation and the extended surface divergence theorems are proposed for the piecewise smooth tensor fields acting on the regular and piecewise regular surfaces. The recently formulated resultant, two-dimensionally exact, thermodynamic shell relations - the balances of mass, linear and angular...
-
New trends in a development of the contemporary lighting forms within the urban environment
PublikacjaThis paper presents selected issues on the design of urban lighting forms including street luminaires within the urban environment. The purpose of this paper is to show the evolution of urban lighting forms, in terms of their performance, character, and in the context of the progression of new lighting technologies. The authors discuss chosen aspects related to the development of lighting forms and the changing role of lighting...
-
Influence of magnetic field on wear in high frequency reciprocatingsliding contacts
PublikacjaResults of experimental studies concerning the influence of permanent magnetic field on wear of dry sliding contact operating at short stroke and high frequency are presented. It was found that horizontal magnetic field with different orientations relative to the sliding direction is affecting performance of the contact. The increase in frequency of sliding reduces accumulated mass loss and lowers the surface roughness of the wear...
-
Study of the influence of thermal factors on the welding process of polyethylene gas pipelines,
PublikacjaA one-dimensional calculation scheme is proposed with the help of which it is possible to determine and set the technological parameters with the accuracy to be realized in production conditions: the temperature of the heating element and the heating time, which allows maximum mechanization of the technological operations of polyethylene gas pipelines welding. The numerical value of the coefficient of temperature for polyethylene...
-
Modeling of Human Tissue for Medical Purposes
PublikacjaThe paper describes the possibilities offered for medicine by modeling of human tissue using virtual and augmented reality. It also presents three proposals of breast modeling for the use in clinical practice. These proposals are the result of arrangements of medical and computer scientists team (the authors) and will be pursued and implemented in the near future. There is included also a brief description of the most popular methods...
-
TIME-OF-FLIGHT DIFFERENTIAL ELECTRON SCATTERING FROM MOLECULAR TARGETS: BENCHMARK CROSS SECTIONS
PublikacjaWe report time-of-flight differential cross section (DCS) measurements for the electron impact excitation transition in H2. In this work, agreement between available theory and experiment is excellent overall, and marks a transition in electron molecule scattering where differential scattering of excitation is found to be in such precise agreement. We also prove that the newly built apparatus can be used for accurate measurement...
-
Modeling BIM Objects From Point Clouds. Examples
PublikacjaThe article presents several ways to obtain BIM (Building Information Modeling) models from point clouds using standard commands in Revit 2018. In Revit geometric forms are possible to obtain in project, family or conceptual environments. Efficient modeling requires knowledge of methods of creating families and components in these environments and ways to combine them. Modeling methods with system and loadable families are presented,...
-
Experimental study on plate modal parameters
PublikacjaTest doświadczalny jest częścią systemu diagnostycznego. Autorzy badają wpływ dodatkowej masy na parametry modalne wolno popartej stalowej płytyi. Artykół przedstawia technikę wyznaczania parametrów modalnych dla systemów monitorowania konstrukcji.The experimental test introduced in the paper is the part of the diagnostic system. The authors investigate the influence of the additional mass on modal parameters of simply supported...
-
Application of a cellular automaton to simulations of granular flow in silos
PublikacjaA cellular automaton based on a gas model of hydrodynamics was used to calculate the kinematics of non-cohesive granular materials during confined flow in a mass flow and funnel flow model silo. In the model, collisions of particles were taken into account during granular flow. In addition, a simplified automaton was used wherein granular flow was assumed as an upward propagation of holes through a lattice composed of cells representing...
-
Simulation of a linear pneumatic actuator with 32 mm piston diameter, 12 mm piston rod diameter and 25 mm stroke
Dane BadawczeThe aim of the simulation was to determine the dynamics of linear pneumatic actuators with different sizes and flow properties. The simulation used the actuator dynamics model as described in [1] and the St Venant - Wantzel's mass flow rate model. The simulation experiment was to calculate the pressure changes in both chambers of the actuator as well...
-
Simulation of a linear pneumatic actuator with 63 mm piston diameter, 20 mm piston rod diameter and 100 mm stroke
Dane BadawczeThe aim of the simulation was to determine the dynamics of linear pneumatic actuators with different sizes and flow properties. The simulation used the actuator dynamics model as described in [1] and the St Venant - Wantzel's mass flow rate model. The simulation experiment was to calculate the pressure changes in both chambers of the actuator as well...
-
Simulation of a linear pneumatic actuator with 32 mm piston diameter, 14 mm piston rod diameter and 500 mm stroke
Dane BadawczeThe aim of the simulation was to determine the dynamics of linear pneumatic actuators with different sizes and flow properties. The simulation used the actuator dynamics model as described in [1] and the St Venant - Wantzel's mass flow rate model. The simulation experiment was to calculate the pressure changes in both chambers of the actuator as well...
-
Simulation of a linear pneumatic actuator with 63 mm piston diameter, 25 mm piston rod diameter and 50 mm stroke
Dane BadawczeThe aim of the simulation was to determine the dynamics of linear pneumatic actuators with different sizes and flow properties. The simulation used the actuator dynamics model as described in [1] and the St Venant - Wantzel's mass flow rate model. The simulation experiment was to calculate the pressure changes in both chambers of the actuator as well...
-
Simulation of a linear pneumatic actuator with 63 mm piston diameter, 20 mm piston rod diameter and 200 mm stroke
Dane BadawczeThe aim of the simulation was to determine the dynamics of linear pneumatic actuators with different sizes and flow properties. The simulation used the actuator dynamics model as described in [1] and the St Venant - Wantzel's mass flow rate model. The simulation experiment was to calculate the pressure changes in both chambers of the actuator as well...
-
Simulation of a linear pneumatic actuator with 100 mm piston diameter, 25 mm piston rod diameter and 500 mm stroke
Dane BadawczeThe aim of the simulation was to determine the dynamics of linear pneumatic actuators with different sizes and flow properties. The simulation used the actuator dynamics model as described in [1] and the St Venant - Wantzel's mass flow rate model. The simulation experiment was to calculate the pressure changes in both chambers of the actuator as well...
-
Simulation of a linear pneumatic actuator with 100 mm piston diameter, 32 mm piston rod diameter and 25 mm stroke
Dane BadawczeThe aim of the simulation was to determine the dynamics of linear pneumatic actuators with different sizes and flow properties. The simulation used the actuator dynamics model as described in [1] and the St Venant - Wantzel's mass flow rate model. The simulation experiment was to calculate the pressure changes in both chambers of the actuator as well...
-
Simulation of a linear pneumatic actuator with 63 mm piston diameter, 20 mm piston rod diameter and 500 mm stroke
Dane BadawczeThe aim of the simulation was to determine the dynamics of linear pneumatic actuators with different sizes and flow properties. The simulation used the actuator dynamics model as described in [1] and the St Venant - Wantzel's mass flow rate model. The simulation experiment was to calculate the pressure changes in both chambers of the actuator as well...