Filtry
wszystkich: 2244
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: THE BEST SPINDLE SPEED
-
Investigation of Weigh-in-Motion Measurement Accuracy on the Basis of Steering Axle Load Spectra
PublikacjaWeigh-in-motion systems are installed in pavements or on bridges to identify and reduce the number of overloaded vehicles and minimise their adverse eect on road infrastructure. Moreover, the collected trac data are used to obtain axle load characteristics, which are very useful in road infrastructure design. Practical application of data from weigh-in-motion has become more common recently, which calls for adequate attention to...
-
Analysis of Residual Stresses and Dislocation Density of AA6082 Butt Welds Produced by Friction Sir Welding
PublikacjaThe Friction Stir Welding (FSW) method was employed to join AA6082 sheets. The welds were produced with different tool traverse speed (200 and 250 mm/min), rotational speed (1000 and 1250 RPM) and tool tilt angle (0 and 2 deg). Based on the analysis of XRD patterns, the total precipitation volume fractions in the nugget zones and the base material were calculated. The FSW process resulted in a reduction in the fraction of precipitates...
-
Energy Management for PV Powered Hybrid Storage System in Electric Vehicles Using Artificial Neural Network and Aquila Optimizer Algorithm
PublikacjaIn an electric vehicle (EV), using more than one energy source often provides a safe ride without concerns about range. EVs are powered by photovoltaic (PV), battery, and ultracapacitor (UC) systems. The overall results of this arrangement are an increase in travel distance; a reduction in battery size; improved reaction, especially under overload; and an extension of battery life. Improved results allow the energy to be used efficiently,...
-
Contribution of dynamic vehicle loads to pavement failure
PublikacjaPavement surfaces are not ideally even, which causes dynamic loads of vehicle axles. Distribution of dynamic loads of a given axle is similar to normal distribution and can be described by static load and dynamic load coefficient. The dynamic load coefficient depends on road profile, vehicle speed, properties of suspensions and static load of axle. While for a given road section road profile remains constant, vehicle speed and...
-
Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082
PublikacjaThe friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
-
Research of Emergency Modes of Wind Power Plants Using Computer Simulation
PublikacjaThe aim of this study is to investigate changes in the wind power plant energy production parameters under the conditions of sudden wind changes and voltage drop. To achieve these goals, a simulation of operation of wind power plants was performed. Twelve wind turbines with variable rotational speed equipped with a Fuhrländer FL 2500/104 asynchronous double-fed induction generator (DFIG) were used, each with an installed capacity...
-
Tensile strength test of PE foils modified with zinc oxide and zinc salts
Dane BadawczeThis dataset contains the results of PE foils mechanical tests, in which the material was evaluated for strength and extensibility at the moment of breaking and based on the same tests preceded by material fatigue in 50 stretching cycles. The principle of the method is to stretch the test sample placed in the clamps of the stretching apparatus at a...
-
Współczynniki strat energetycznych w elementach napędu hydrostatycznego
PublikacjaW każdym układzie napędowym należy zastąpić obraz przepływu mocy opisany dotychczas powszechnie stosowanym wykresem Sankey’a spadku mocy zgodnego z kierunkiem przepływu mocy proponowanym przez autora wykresem wzrostu mocy w układzie przeciwnego do kierunku przepływu mocy. Należy więc opisywać straty i sprawność energetyczną a także pole pracy każdego silnika i układu napędowego jako zależne od wielkości fizycznych niezależnych...
-
Titania nanotubes infiltrated with conducting polymer PEDOT modified by Prussian Blue – a novel type of organic-inorganic heterojunction characterised with enhanced photoactivity.
PublikacjaA highly ordered p–n heterojunction was formed based on titania nanotubes containing a conducting polymer with Prussian blue matrix. The study demonstrates, for the first time, cases when a composite based on titania array scaffolding and Prussian blue embedded in PEDOT exhibits reversible FeII/FeIII redox activity. Highly enhanced photoactivity and capacitance of the obtained material are depicted in comparison to pristine titania....
-
Observation value analysis - integral part of Bayesian diagnostics
PublikacjaDetailed subject of the research is to analyse the value of the observation, which is a part of preposterior analysis. For the presented network, the main objective was to determine, conducting of which of three tests is the most valuable from the perspective of determining possible need or possibility to omission expensive technical expertise. The main advantage of preposterior analysis is answering the question which of the considered...
-
Assessment of risks introduced to safety critical software by agile practices - a software engineer's perspective
PublikacjaIn this article we investigate the problem of applying agile practices into safety-critical projects.The goal of our research is to investigate potential benefits from introducing agile practicesinto safety-critical environment and to present a solution providing for balancing agileapproach with more disciplined assurance techniques, bringing the best of the two worlds together.In the article we present the supporting ideas such...
-
Design analysis of Tesla micro-turbine operating on a low-boiling medium
PublikacjaThis paper presents results of the design analysis of a Tesla bladeless turbine intended for a co-generating micro-power plantof heat capacity 20 kW, which operates in an organic Rankine cycle on a low-boiling medium. Numerical calculations of flowin several Tesla turbine models were performed for a range of design parameters. Results of investigations exhibit interestingfeatures in the distribution of flow parameters within the...
-
Search for the most useful geometry of an acoustic journal bearing
PublikacjaComputer simulations of a number of journal bearing’s geometries utilising acoustic levitation were carried out. The choice of the best geometry depended on the ability of a deformed shape, created by piezo-electric elements, to facilitate squeeze film ultrasonic levitation, and also to create three evenly distributed diverging aerodynamic gaps. Deformations of analysed variants of the bearing’s shape were generated by numerical...
-
Alhassan Ali Ahmed
OsobyAlhassan Ali Ahmed BSc of pharmacy, MSc in Bioinformatics and Biotechnology, and currently doing his PhD in Bioinformatics and Machine Learning. Alhassan has considerable experience in the pharmaceutical industry as he worked before in different positions such as; Community pharmacist, Medical advisor, Antibiotics production specialist, Quality assurance specialist, Key account manager for Immunotherapeutic medications, and currently,...
-
Real-time generator of AIS/ARPA/GPS data
PublikacjaThe paper presents a real-time generator of AIS/ARPA/GPS position data in the standardized NMEA 0183 text format. Position data are produced by a set of various types of ships simulated on the Polish part of the Baltic Sea and are generated on defined IP/UDP addresses and RS-232 ports. In the simulation an extensive set of input parameters is taken into account including the number of particular types of ships, their dimensions,...
-
Enhanced Eye-Tracking Data: a Dual Sensor System for Smart Glasses Applications
PublikacjaA technique for the acquisition of an increased number of pupil positions, using a combined sensor consisting of a low-rate camera and a high-rate optical sensor, is presented in this paper. The additional data are provided by the optical movement-detection sensor mounted in close proximity to the eyeball. This proposed solution enables a significant increase in the number of registered fixation points and saccades and can be used...
-
CMOS implementation of an analogue median filter for image processing in real time
PublikacjaAn analogue median filter, realised in a 0.35 μm CMOS technology, is presented in this paper. The key advantages of the filter are: high speed of image processing (50 frames per second), low-power operation (below 1.25 mW under 3.3 V supply) and relatively high accuracy of signal processing. The presented filter is a part of an integrated circuit for image processing (a vision chip), containing: a photo-sensor matrix, a set of...
-
Application in circular sawing machines of the experimental results of investigations of the chip removing system operation
PublikacjaThe experimental results of the chip removing system operation are presented. The main aim of them was to optimize suction system of the panel saw Fx3 and its follower Fx550. The attention was focused on the upper casing, which was the part of removing system. Within the framework of the work a systematic experimental study of pressure distribution in the casing during operation of the selected rotational speed of saw blade with...
-
Analog CMOS processor for early vision processing with highly reduced power consumption
PublikacjaA new approach to an analog ultra-low power visionchip design is presented. The prototype chip performs low-levelconvolutional image processing algorithms in real time. Thecircuit is implemented in 0.35 μm CMOS technology, contains64 x 64 SIMD matrix with embedded analogue processors APE(Analogue Processing Element). The photo-sensitive-matrix is of2.2 μm x 2.2 μm size, giving the density of 877 processors permm2. The matrix dissipates...
-
Characteristics of an image sensor with early-vision processing fabricated in standard 0.35 µm CMOS technology
PublikacjaThe article presents measurement results of prototype integrated circuits for acquisition and processing of images in real time. In order to verify a new concept of circuit solutions of analogue image processors, experimental integrated circuits were fabricated. The integrated circuits, designed in a standard 0.35 µm CMOS technology, contain the image sensor and analogue processors that perform low-level convolution-based image...
-
Comparison of Tracking Methods in Respect of Automation of Animal Behavioral Test
PublikacjaAutomation in experiments carried out on animals is getting more and more important in research. Computers take over laborious and time-consuming activities like recording and analysing images of experiment scene. The first step in an image analysis is finding and distinguishing between the observed animals, and then tracking all objects during the experiment. In this paper four tracking methods are presented. Quantitative and...
-
A multistage turbine for a micro power plant
PublikacjaThis paper presents results of a design analysis of a multi-stage turbine for the cogeneration micro-power plant working in accordance with Organic Rankine Cycle (ORC). The heat power of the plant is assumed equal to 20 kW and the corresponding available electric output is estimated to be of about 3 kW. Different variants of the radial and axial-flow turbines have been considered, while the detailed results of the calculations...
-
Application of wireless communication to small WECS with induction generator
PublikacjaWind energy conversion systems (WECS) seem to be self-evident elements of the future smart grids. Among many generator types the squirrel cage induction generator (SCIG) characterizes robustness and low cost. A full-scale power converter can perform smooth grid connection over wide speed range of multiple-stage geared SCIG. Increasing number of sensors can improve the WECS control and diagnostics but increasing number of thin wires...
-
Numerical investigation on the performance of a small counter-rotating wind turbine
PublikacjaThe article presents the results of the investigation on the performance of a small counter-rotating wind turbine. The wind turbine has been simulated using Computational Fluid Dynamics methods. Actuator Line Model has been successfully used to represent rotors in the computational domain. A parametric study has been carried out, taking into account changes in the tip speed ratio of the rotors while maintaining a constant distance...
-
Emotion Recognition - the need for a complete analysis of the phenomenon of expression formation
PublikacjaThis article shows how complex emotions are. This has been proven by the analysis of the changes that occur on the face. The authors present the problem of image analysis for the purpose of identifying emotions. In addition, they point out the importance of recording the phenomenon of the development of emotions on the human face with the use of high-speed cameras, which allows the detection of micro expression. The work that was...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublikacjaPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
A bound on the number of middle-stage crossbars in f-cast rearrangeable Clos networks
PublikacjaIn 2006 Chen and Hwang gave a necessary and sufficient condition under which a three-stage Clos network is rearrangeable for broadcast connections. Assuming that only crossbars of the first stage have no fan-out property, we give similar conditions for f-cast Clos networks, where f is an arbitrary but fixed invariant of the network. Such assumptions are valid for some practical switching systems, e.g. high-speed crossconnects....
-
Approximate models and parameter analysis of the flow process in transmission pipelines
Publikacjathe paper deals with the problem of early leak detection in transmission pipelines. First we present the derivation of state-space equations of the flow process in the pipelines. This description is then aggregated in order to obtain a principal model. Next, the problem of process model parameterization is addressed, taking into account the maximization of a model stability margin. The location of the maximum is determined using...
-
One Europe, one product, two prices - the price disparity in the EU
PublikacjaThe price dispersion in the European Union in the last fifteen years (1990-2005) is analysed. The analysis of price convergence is examined on aggregate and disaggregate levels. The macro approach is based on Comparative Price Level index calculated as the ratio between PPPs and exchange rate. The disaggregate analysis utilizesactual prices of 148 individual products sold in the 15 capital cities of the EU. The calculations comprise...
-
Decahedral-shaped anatase titania photocatalyst particles: Synthesis in a newly developed coaxial-flow gas-phase reactor
PublikacjaDecahedral-shaped anatase particles (DAPs) were prepared by a gas-phase process consisting of titanium(IV) chloride oxidation. The use of a coaxial-flow gas-phase reactor resulted in high reaction yield (ca. 70%) and good reproducibility of DAPs production. The influence of controlled and resultant preparation parameters on the process course and on DAPs properties (such as specific surface area, particle size and particle morphology)...
-
Studies on Treatment of Bitumen Effluents by Means of Advanced Oxidation Processes (AOPs) in Basic pH Conditions
PublikacjaThe paper presents the results of studies on chemical treatment of effluents from production of bitumen of petroleum origin. Due to the presence of sulfide ions, the pH of these effluents is strongly alkaline. Several Advanced Oxidation Processes (AOPs) were studied, including the use of hydroxyl and sulfate radicals oxidants, the hydrodynamic cavitation as well as sonocavitation. The best processes allow to obtain 45% reduction...
-
Studies on treatment of bitumen effluents by means of Advanced Oxidation Processes (AOPs) in basic pH conditions
PublikacjaThe paper presents the results of studies on chemical treatment of effluents from production of bitumen of petroleum origin. Due to the presence of sulfide ions, the pH of these effluents is strongly alkaline. Several Advanced Oxidation Processes (AOPs) were studied, including the use of hydroxyl and sulfate radicals oxidants, the hydrodynamic cavitation as well as sonocavitation. The best processes allow to obtain 45% reduction...
-
Multipath routing for quality of service differentiation and network capacity optimization in broadband low-earth orbit systems
PublikacjaThis paper shows the importance of employing multiple different paths for routing in Inter-Satellite Link (ISL) networks in broadband Low-Earth Orbit (LEO) satellite systems. A theoretical analysis is presented and a routing concept is proposed to demonstrate three facts that make multipath routing especially important in broadband LEO networks: (1) differences in the propagation delays have a much greater impact on end-to-end...
-
Performance Evaluation of Preemption Algorithms in MPLS Networks
PublikacjaPreemption is a traffic engineering technique in Multiprotocol Switching Networks that enables creation of high priority paths when there is not enough free bandwidth left on the route. Challenging part of any preemption method is to select the best set of paths for removal. Several heuristic methods are available but no wider comparison had been published before. In this paper, we discuss the dilemmas in implementing preemption...
-
Nilpotent singularities and chaos: Tritrophic food chains
PublikacjaLocal bifurcation theory is used to prove the existence of chaotic dynamics in two well-known models of tritrophic food chains. To the best of our knowledge, the simplest technique to guarantee the emergence of strange attractors in a given family of vector fields consists of finding a 3-dimensional nilpotent singularity of codimension 3 and verifying some generic algebraic conditions. We provide the essential background regarding...
-
Vapor correction of FTIR spectra – A simple automatic least squares approach
PublikacjaFTIR spectroscopy is one of the best techniques to study intermolecular interactions. However, such an application requires high quality spectra with as little noise as possible, which are often difficult to obtain. One of the main sources of unwanted interference is water vapor. Here a robust method is proposed for automatic, fast and reliable vapor correction of FTIR spectra. The presented least squares approach of vapor subtraction...
-
Modelowanie kratownicy z kształtowników giętych na zimno z mimośrodami dodatnimi w węźle = Modelling of truss with cold-formed section and positive eccentricyty in the node.
PublikacjaThe topic of this research is establishing load-carrying capacity of compressed and tensed chords of trusses made of cold-formed open cross-sections. Occurrence of bending in the truss’ chord is the result of specific production technology assumed by the designer and producer of lattice girder’s systems. The aim of this research is to present methodology of conduct while creating numerical models that best depict the behaviour...
-
Accelerating Video Frames Classification With Metric Based Scene Segmentation
PublikacjaThis paper addresses the problem of the efficient classification of images in a video stream in cases, where all of the video has to be labeled. Realizing the similarity of consecutive frames, we introduce a set of simple metrics to measure that similarity. To use these observations for decreasing the number of necessary classifications, we propose a scene segmentation algorithm. Performed experiments have evaluated the acquired...
-
Modeling of truss with cold-formed section and positive eccentricity in the node
PublikacjaThis work is dedicated to establishing the load carrying capacity of tensed and compressed truss’ nodes made of cold-formed open cross sections. The occurrence of bending in the truss’ nodes is the result of a specific production technology for system lattice girders assumed by the designer and the producer. The aim of this research is to present the methodology of conduct for creation of computational models that best depict the...
-
Multicriteria Decision Analysis and Grouping of Analytical Procedures for Phthalates Determination in Disposable Baby Diapers
PublikacjaThis study presents the application of one of the tools from the multicriteria decision analysis set (MCDA), the Technique for Order Preference by Similarity to Ideal Solution (TOPSIS). Selected green analytical chemistry metrics were used to rank analytical procedures for the phthalate determination in disposable baby diapers. Nine analytical procedures were assessed in order to find one that has the lowest environmental impact...
-
Zintegrowane działania komunikacyjne w internecie na przykładzie marki Żywiec Zdrój Smako-Łyk
PublikacjaArtykuł ma na celu ukazanie przykładów angażowania polskich internautów w kampanie komunikacji marketingowej realizowane dla marki Żywiec Zdrój Smako-Łyk. Analizie poddano treści odnoszące się bezpośrednio do marki oraz wybranych kampanii online prowadzonych w latach 2009–2015. W ostatnich latach w Polsce można obserwować coraz więcej kampanii wykorzystujących potencjał, jaki mają w sobie internauci. Cenne pomysły można pozyskać...
-
Badania mieszanek mineralno-asfaltowych w niskiej temperaturze
PublikacjaW artykule przedstawiono metody badań w niskiej temperaturze betonu asfaltowego przeznaczonego do warstwy ścieralnej. Przedstawione zostały wyniki badań dla 4 różnych metod badawczych: zginania, pełzania, pośredniego rozciągania oraz rozciągania termicznego przy ograniczonym odkształceniu (test TSRST). Próbki betonu asfaltowego były przygotowywane w laboratorium z wykorzystaniem 3 rodzajów asfaltów: asfaltu zwykłego, asfaltu modyfikowanego...
-
Continuous wave sonar with hyperbolic frequency modulation keyed by pseudo-random sequence
PublikacjaA CW FM type sounding signal is used in the classical solution of silent sonar. While the signal provides a relatively simple implementation of digital signal processing, and ensures good detection conditions, unfortunately, in the presence of the Doppler effect, distance measurement results tend to be wrong. This is due to the fact that the received signal’s instantaneous frequency value is dependent both on the distance to the...
-
Performance evaluation of the parallel object tracking algorithm employing the particle filter
PublikacjaAn algorithm based on particle filters is employed to track moving objects in video streams from fixed and non-fixed cameras. Particle weighting is based on color histograms computed in the iHLS color space. Particle computations are parallelized with CUDA framework. The algorithm was tested on various GPU devices: a desktop GPU card, a mobile chipset and two embedded GPU platforms. The processing speed depending on the number...
-
Modern Platform for Parallel Algorithms Testing: Java on Intel Xeon Phi
PublikacjaParallel algorithms are popular method of increasing system performance. Apart from showing their properties using asymptotic analysis, proof-of-concept implementation and practical experiments are often required. In order to speed up the development and provide simple and easily accessible testing environment that enables execution of reliable experiments, the paper proposes a platform with multi-core computational accelerator:...
-
Sensorless induction motor drive with voltage inverter and sine-wave filter
PublikacjaThis paper presents a speed sensorless control system of an induction motor with an output LC filter. It is known that the parameters design of the filter gives sine wave motor supply voltage but complicates control and estimation process. The reason is that the voltage drop and phase shift between filter input and output signals are imposed, and hence the motor voltages and currents differ from the inverter output waveforms. To...
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublikacjaThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
A correlation between electron-hole pair radii and magnetomodulation of exciplex fluorescence in electron donor-electron acceptor organic systems
PublikacjaElectric field dependencies of electromodulated photoluminescence and magnitudes of the magnetic-field effect on photoluminescence havebeen measured in vacuum-evaporated films of m-MTDATA [4,4',4"-tris(N-(3-methylphenyl)-N-phenylamino)triphenylamine]:bathophe-nanthroline, m-MTDATA:BCP (bathocuproine), as well as 4,4',4"-tris[2-naphthyl(phenyl)amino]triphenylamine:BCP. The Sano-Tachiya-Noolandi-Hong extension of standard Onsager...
-
Feedback Control of Multiphase Induction Machines with Backstepping Technique
PublikacjaThe paper presents the control possibility of five phase induction machines. In the proposed solution the machine model vector form is not transformed to the (dq)-coordinate system, that is connected to rotor flux vector, but utilizes the stationary system ( αβ ). Moreover, the nonlinear model linearization is based on demonstrated nonlinear variables transformation for i-orthogonal ( αβ )(n) planes. By introducing the backstepping...
-
Extended duration running and impulse loading characteristics of an acoustic bearing with enhanced geometry
PublikacjaThis paper presents performance during prolonged running of the acoustic bearing when PZTs are switched off and when they are switched on. The effect of active PZT on shaft’s displacements in X and Y directions is clearly demonstrated. Performance of the acoustic bearing was also assessed when an impulse force was applied to the running shaft at speed. Once again the benefits of having PZTs active are beyond doubt. The instability...