Filtry
wszystkich: 1092
-
Katalog
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: plate/beam%20theory
-
Thermal Instability of Gold Thin Films
PublikacjaThe disintegration of a continuous metallic thin film leads to the formation of isolated islands, which can be used for the preparation of plasmonic structures. The transformation mechanism is driven by a thermally accelerated diffusion that leads to the minimalization of surface free energy in the system. In this paper, we report the results of our study on the disintegration of gold thin film and the formation of nanoislands...
-
A Wideband Rotary-Joint-Free H-Plane Horn Antenna With 360° Steerable Radiation Pattern Using Gap Waveguide Technology
PublikacjaConsidering the limitations of electronically steerable antennas such as limited steering span, gain degradation for large steering angles, complexity, and cost, this article is focused on the design of a simple mechanically steerable H-plane horn antenna. It is shown that since there is no need for an electrical connection between the top and bottom sections of a gap waveguide (GWG), if a sectoral horn is properly designed and realized...
-
Cyclic deformation and fracture behaviour of additive manufactured maraging steel under variable-amplitude loading
PublikacjaThe cyclic deformation and fracture behaviour of 18Ni300 maraging steel produced by laser beam powder bed fusion is studied under variable-amplitude loading. The tests were conducted under fully-reversed strain-controlled conditions with a loading sequence comprising three ascending cycles and three descending cycles repeated sequentially until failure. After the tests, fracture surfaces were examined using height and volume surface...
-
BACTERIAL INACTIVATION VIA LASER-DRIVEN GOLD NANOPARTICLE HEATING: SIMULATION AND ANALYSIS
PublikacjaThis study utilizes CFD technique to simulate the inactivation of E. coli bacteria within a microfluidic chamber, employing gold nanoparticles irradiated by a laser beam. Employing a single-phase model, the presence of bacteria is considered by treating thermal properties in the governing equations as effective, combining those of water and bacteria using established correlations from scientific literature. The conversion of light...
-
Schemes of transmission of classical information via quantum channels with many senders: Discrete- and continuous-variable cases
PublikacjaSuperadditivity effects in the classical capacity of discrete multiaccess channels and continuous variable (CV) Gaussian MACs are analyzed. Several examples of the manifestation of superadditivity in the discrete case are provided, including, in particular, a channel which is fully symmetric with respect to all senders. Furthermore, we consider a class of channels for which input entanglement across more than two copies of the...
-
Nonlinear finite element modeling of vibration control of plane rod-type structural members with integrated piezoelectric patches
PublikacjaThis paper addresses modeling and finite element analysis of the transient large-amplitude vibration response of thin rod-type structures (e.g., plane curved beams, arches, ring shells) and its control by integrated piezoelectric layers. A geometrically nonlinear finite beam element for the analysis of piezolaminated structures is developed that is based on the Bernoulli hypothesis and the assumptions of small strains and finite...
-
On local buckling of cold-formed channel members
PublikacjaThe paper deals with local buckling of the compressed flanges of cold-formed thin-walled channel beams subjected to pure bending or axially compressed columns. Arbitrarily shaped flanges of open cross-sections and the web-flange interactions are taken into account. Buckling deformation of a beam flange is described by displacement related to torsion of the flange about the line of its connection with the web. Total potential energy...
-
Computational fluid dynamics simulation of heat transfer from densely packed gold nanoparticles to isotropic media
PublikacjaThis work aims to determine and compare heat generation and propagation of densely packed gold nanoparticles (Au NPs) induced by a resonant laser beam (532 nm) according to the Mie theory. The heat flux propagation is transferred into the materials, which here are: silica glass; soda-lime-silica glass; borosilicate glass; polymethyl methacrylate (PMMA); polycarbonate (PC); and polydimetylosiloxane (PDMS). This analysis aims to...
-
Mechanical Properties of Twisted Carbon Nanotube Bundles with Carbon Linkers from Molecular Dynamics Simulations
PublikacjaThe manufacturing of high-modulus, high-strength fibers is of paramount importance for real-world, high-end applications. In this respect, carbon nanotubes represent the ideal candidates for realizing such fibers. However, their remarkable mechanical performance is difficult to bring up to the macroscale, due to the low load transfer within the fiber. A strategy to increase such load transfer is the introduction of chemical linkers...
-
Influence of Selected Warm Mix Asphalt Additives on Cracking Susceptibility of Asphalt Mixtures
PublikacjaWarm mix asphalt (WMA) has been widely accepted as a future asphalt paving technology. Besides clear advantages, there are still some concerns regarding durability and long-term performance of pavements made with this type of asphalt mixtures. One of the most important issues is low temperature behaviour of WMA because certain additives used for temperature reduction can aect bitumen properties. This paper presents the evaluation...
-
Individual contributions of M X-ray line from Cu- and Co-like tungsten ions and L X-ray line from Ne-like molybdenum ions – Benchmarks for new approach to determine the high-temperature tokamak plasma parameters
Publikacja -
Energy shift of the Lβ2 line as an ionization diagnostic for the dense plasma in the PFRP
Publikacja -
Modeling of soft N, M and L X-ray lines from tungsten relevant to plasma parameters in the WEST tokamak
Publikacja -
Elastic cross-section calculations for electron collisions with XY4 (X=Si,Ge; Y=H, F, Cl, Br, I) molecules
PublikacjaObliczano elastyczne przekroje czynne dla tetraedrycznych związków krzemu i germanu. Otrzymane wyniki porównano z innymi dostępnymi wynikami obliczeń oraz z danymi doświadczalnymi; dla energii powyżej 100 eV uzyskano zadowalającą zgodność.
-
Theoretical Auger and photoionization studies for open shell atoms andions.
PublikacjaWykorzystano program komputerowy RATIP do badań własności atomów i jonów o dowolnej konfiguracji. Położono nacisk na obliczenia szeregu własności elektronów Augera i fotojonizacji, aby dokonać porównań z ostatnio wykonywanymi doświadczeniami.
-
Dissolution of Nb-doped hydroxyapatite prepared via low-temperature mechanochemical method: Spectroscopy studies
PublikacjaCalcium phosphate glass ceramics with nominal hydroxyapatite stoichiometry doped with niobium were synthesized using simple as well as low-temperature mechanochemical method and then in the form of compressed pellet were submitted to the static dissolution process in distilled water for one month. The results of structural analysis, performed mainly on the base of spectroscopic methods such as: infrared absorption spectroscopy,...
-
Nano-structured Pt embedded in acidic salts of heteropolymolybdate matrices: MS EXAFS study
PublikacjaA structural study of Pt nano-catalysts is presented in the paper. The innovation in the case of the considered catalytic materials resides in the use a meso-microporous inorganic matrix of heteropolyacid salt of composition X2.5H0.5YMo12O40 where X = Rb, Cs and Y = P, Si as a catalyst support. Metallic nanoparticles were created by platinum ions reduction in a hot H2/Argon stream and were mainly located into matrix pores. As the...
-
Annihilation rates of low-energy positron scattering from simple diatomic molecules
PublikacjaWe discuss the calculations of Zeff coefficients for a series of diatomic molecules over the range of energies below the positronium formation. During the development of a general code for polyatomic, nonlinear molecules colliding with positrons, it was discovered that the earlier one, employed only for diatomic molecules, had an error. The error is corrected and the corrected results are presented here. We also discuss a way of...
-
Correlation–polarization effects in electron/positron scattering from acetylene: A comparison of computational models
PublikacjaDifferent computational methods are employed to evaluate elastic (rotationally summed) integral and differential cross sections for low energy (below about 10 eV) positron scattering off gas-phase C2H2 molecules. The computations are carried out at the static and static-plus-polarization levels for describing the interaction forces and the correlation–polarization contributions are found to be an essential component for the correct...
-
Polarisation effects in low-energy positron–molecule scattering
PublikacjaThe UK molecular R-matrix method has been adapted to treat positron collisions from polyatomic targets. A simple empirical enhancement factor which corrects for the underestimation of electron–positron polarisation and correlation effects in the calculations performed with the static-plus-polarization model at low scattering energies is presented. Application of this model to positron scattering from carbon dioxide at energies...
-
The microbial and sensory quality of mackerel hot smoked in mild conditions
PublikacjaThe quality indices of Atlantic mackerel, hot smoked at core temperature not exceeding 60°C, containing 14–27 g salt and 580–670 g water per kg meat, was determined just after smoking and during storage. The aerobic plate count after smoking, chilling and packing in cardboard boxes was 0–12 cfu/25 cm2of the skin of the smoked fish and 10–240 cfu/g of flesh. It was 1.9 log cycle lower than that in the frozen raw material. At 2°C,...
-
A comparative analysis of phenotypic and genotypic methods for the determination of the biofilm-forming abilities of Staphylococcus epidermidis
PublikacjaThe collection of 146 Staphylococcus epidermidis strains isolated from the nasopharynx of lung cancer patients has been studied for the ability of slime secretion and biofilm formation using the Congo red agar (CRA) test and the microtiter plate (MtP) method, respectively. The prevalence of the icaAD and the aap genes was also analyzed. Some isolates (35.6%) were biofilm positive by the MtP method, while 58.9% of isolates exhibited...
-
Fabrication and Significant Photoelectrochemical Activity of Titania Nanotubes Modified with Thin Indium Tin Oxide Film
PublikacjaOrdered titanium dioxide nanotubes (TiO2NTs) modified with indium tin oxide (ITO) films were obtained via magnetron sputtering, in which ITO plate was used as a target, onto the as-anodized titania support followed by the calcination process. The morphology of fabricated material with deposited oxide was investigated using scanning electron microscopy. Raman and UV–Vis spectroscopies were utilized to characterize crystalline phase...
-
Fracture Energy of Bonded Joints with 2D Elastic Adhesive Layer
PublikacjaWhen bonded joint is subjected to mode I fracture loading, the adhesive joints analytical solutions treats the adhesive layer, usually, as not existing or 1D Hooke elastic layer. In the case of 1D elastic layer, represented as Hookes spring element, is acting, only, in direction contrary to the applied load. Basing on the information yielded from sensitive laser profilometry technique, where deflections of bonded part of the joint...
-
A comparative analysis of phenotypic and genotypic methods for the determination of the biofilm-forming abilities of Staphylococcus epidermidis
PublikacjaThe collection of 146 Staphylococcus epidermidis strains isolated from the nasopharynx of lung cancer patients has been studied for the ability of slime secretion and biofilm formation using the Congo red agar (CRA) test and the microtiter plate (MtP) method, respectively. The prevalence of the icaAD and the aap genes was also analyzed. Some isolates (35.6%) were biofilm positive by the MtP method, while 58.9% of isolates exhibited...
-
Nonlocal elasticity analysis of moderately thick porous functionally graded plates in a hygro-thermal environment
PublikacjaThis work performs a novel quasi three-dimensional (3D) bending analysis for a moderately thick functionally graded material (FGM) made of nanoceramics and metal powders, in presence of porosities due to some incorrect manufacturing processes. Such porosities can appear within the plate in two forms, namely, even and uneven distributions. The modeled system assumes a polymer matrix where both shear and transverse factors coexist....
-
Chemical, Physical, and Mechanical Properties of 95-Year-Old Concrete Built-In Arch Bridge
PublikacjaThis research aimed to determine the durability and strength of an old concrete built-in arch bridge based on selected mechanical, physical, and chemical properties of the concrete. The bridge was erected in 1925 and is located in Jagodnik (northern Poland). Cylindrical specimens were taken from the side ribs connected to the top plate using a concrete core borehole diamond drill machine. The properties of the old concrete were...
-
Torque capacity of multidisc wet clutch with reference to friction occurrence on its spline connections
PublikacjaIn this article developed mathematical model that includes friction occurrence on spline connections is presented. The work also contains results of experimental research on torque capacity of multidisc wet clutch. These results are expressed as a function of contact pressure for different number of friction surfaces. Due to increased interest in research concerning multidisc wet clutches it is essential to determine impact of...
-
Numerical analysis of high temperature minichannel heat exchanger for recuperative microturbine system
PublikacjaConsidering the development of energy sector, distributed small-scale power generation, e.g., gas micro-CHP, is attracting considerable interest. In such installations, the heat exchanger is one of the key components possessing a significant influence on overall performance. Most studies concentrate on units operating below 900C, which do not fulfil the requirements of gas micro-CHP. Therefore, there remains a challenge to design...
-
Influence of Annealing Atmospheres on Photoelectrochemical Activity of TiO2 Nanotubes Modified with AuCu Nanoparticles
PublikacjaIn this article, we studied the annealing process of AuCu layers deposited on TiO2 nanotubes (NTs) conducted in various atmospheres such as air, vacuum, argon, and hydrogen in order to obtain materials active in both visible and UV–vis ranges. The material fabrication route covers the electrochemical anodization of a Ti plate, followed by thin AuCu film magnetron sputtering and further thermal treatment. Scanning electron microscopy...
-
A Numerical Study on Baseline-Free Damage Detection Using Frequency Steerable Acoustic Transducers
PublikacjaIn structural health monitoring (SHM) a considerable amount of damage detection algorithms based on guided waves (GW) have been developed. Most of them rely on extensive transducer networks, besides preliminary reference measurements of the structures. This originated a growing demand for hardware simplification and cost reduction of the wave-based SHM methods, driving the conception of new solutions enabling both: the reduction...
-
A Colorimetric Microplate Assay for DNA-Binding Activity of His-Tagged MutS Protein
PublikacjaA simple microplate method was designed for rapid testing DNA-binding activity of proteins. The principle of the assay involves binding of tested DNA by his-tagged protein immobilized on a nickel-coated ELISA plate, following colorimetric detection of biotinylated DNA with avidin conjugated to horseradish peroxidase. The method was used to compare DNA mismatch binding activities of MutS proteins from three bacterial species. The...
-
The influence of external interference on AFM imaging, the use of a protective helmet
Dane BadawczeThis collection is of purely practical importance, showing how the presence of external disturbances can adversely affect the quality of imaging with an atomic force microscope. For this reason, it is also advisable to provide a link to a workshop-like study [1] as well as a huge number of commercial solutions available after entering the keyword "AFM...
-
Linear and nonlinear impedance of alkali and iron doped silicate-lead glasses
Dane BadawczeLinear and nonlinear impedance was studied for lead-silicate glass samples doped with iron ions and alkaline oxides. The compositions of glasses were as follows: (in %mol) 50% SiO2, 25% PbO, 15% Fe2O3 and 15% one of alkaline oxides: Na2O, K2O, Li2O. All samples were prepared by the conventional melt quenching technique. The substrates were powdered...
-
A geophysical, geochemical and microbiological study of a newly discovered pockmark with active gas seepage and submarine groundwater discharge (MET1-BH, central Gulf of Gdańsk, southern Baltic Sea)
PublikacjaHigh-resolution bathymetric data were collected with a multi-beam echosounder in the southern part of the Baltic Sea (region MET1, Gulf of Gdańsk) revealing the presence of a 10 m deep and 50 m in diameter pockmark (MET1-BH) on the sea bottom (78.7 m). To date, no such structures have been observed to reach this size in the Baltic Sea. The salinity of the near-bottom water in the pockmark was about 2 PSU (about 31.22 mmol/l...
-
Application of twin-plane ECT sensor for identification of the internal imperfections inside concrete beams
PublikacjaThe main purpose of this paper is to investigate application of special construction of Electrical Capacitance Tomography (ECT) sensor to concrete beams internal homogeneity tests. Identification of internal imperfection inside the concrete beams is one of the main problems related to analysis of the construction structure bearing capacity. Therefore, this paper shows attempts to study the measurement prospects for this non-invasive,...
-
Strain energy density and entire fracture surface parameters relationship for LCF life prediction of additively manufactured 18Ni300 steel
PublikacjaIn this study, the connection between total strain energy density and fracture surface topography is investigated in additively manufactured maraging steel exposed to low-cycle fatigue loading. The specimens were fabricated using laser beam powder bed fusion (LB-PBF) and examined under fully-reversed strain-controlled setup at strain amplitudes scale from 0.3% to 1.0%. The post-mortem fracture surfaces were explored using a non-contact...
-
A Diagnostic Method Based on Deflection Analysis for Monitoring Post-elastic Response of Beams
PublikacjaA non-destructive diagnostic method based on deflection analysis for monitoring the post-elastic response of beams was developed, and a diagnostic indicator was proposed. The indicator was defined as the second moment of the normalised curvature function about the mid-span, where the curvature was computed from the normalised deflection function. Elastic reference values of the indicator were computed for simply supported beams...
-
Advanced Monte Carlo simulator of the polarization-sensitive optical coherence tomography systems
PublikacjaSimulations of the optical coherence tomography (OCT) systems using the Monte Carlo method is a widely explored research area. However, there are several difficulties that need to be overcome in order to properly model the OCT imaging with the Monte Carlo algorithm. First of all, the temporal and the spatial coherence of the scattered light need to be considered, since OCT is based on the interference phenomenon. For the same reason,...
-
Effect of selective laser treatment on initiation of fatigue crack in the main part of an undercarriage drag strut
PublikacjaThis paper presents the results of material characterization and a fatigue test conducted for a laser-re-melted drag strut used in an aircraft landing gear. The drag strut was re-melted with a CO2 laser beam. Eight re-melted paths were made in the form of spiral lines along the axis of the drag strut. Next, the drag strut was subjected to variable loads on a testing machine simulating loads occurring when an aircraft lands. The...
-
Seafloor characterisation using multibeam sonar echo signal processing and image analysis
PublikacjaThe authors propose the approach to multibeam seafloor characterisation which relies on the combined, concurrent use of two different techniques of multibeam sonar data processing. The first one is based on constructing the grey-level sonar images of seabed using the echoes received in the consecutive beams. Then, the parameters describing the local region of sonar image, namely, the local standard deviation of a grey level, and...
-
Non-Linear Analysis of Structures Utilizing Load-Discretization of Stiffness Matrix Method with Coordinate Update
PublikacjaThis paper proposes a stiffness method based structural analysis algorithm for geometrically non-linear structures. In this study, the applied load on the joints has been discretized to a sequence of a few loadings applied. Each loading step produces incremental external nodal displacements, which are added to the corresponding coordinates to get a new geometrical shape of the structure. This process is iteratively repeated until...
-
Flexomagneticity in buckled shear deformable hard-magnetic soft structures
PublikacjaThis research work performs the first time exploring and addressing the flexomagnetic property in a shear deformable piezomagnetic structure. The strain gradient reveals flexomagneticity in a magnetization phenomenon of structures regardless of their atomic lattice is symmetrical or asymmetrical. It is assumed that a synchronous converse magnetization couples both piezomagnetic and flexomagnetic features into the material structure....
-
Laser-assisted modification of titanium dioxide nanotubes in a tilted mode as surface modification and patterning strategy
PublikacjaElectrochemical anodization is regarded as a facile and easily scalable fabrication method of titania nanotubes (TiO2NTs). However, due to the extended duration of calcination and further modifications, much faster alternatives are highly required. As a response to growing interest in laser modification of nanotube arrays, a comprehensive investigation of pulsed-laser irradiation and its effect onto TiO2NT properties has been carried out....
-
Data Compression in Ultrasonic Network Communication via Sparse Signal Processing
PublikacjaThis document presents the approach of using compressed sensing in signal encoding and information transferring within a guided wave sensor network, comprised of specially designed frequency steerable acoustic transducers (FSATs). Wave propagation in a damaged plate was simulated using commercial FEM-based software COMSOL. Guided waves were excited by means of FSATs, characterized by the special shape of its electrodes, and modeled...
-
Non-linear static stability of bi-layer carbon nanosheets resting on an elastic matrix under various types of in-plane shearing loads in thermo-elasticity using nonlocal continuum
PublikacjaIn this research, the shear and thermal buckling of bi-layer rectangular orthotropic carbon nanosheets embedded on an elastic matrix using the nonlocal elasticity theory and non-linear strains of Von-Karman was studied. The bi-layer carbon sheets were modeled as a double-layered plate, and van der Waals forces between layers were considered. The governing equations and boundary conditions were obtained using the first order shear...
-
Experimental and analytical thermal study of PTFE composite sliding against high carbon steel as a function of the surface roughness, sliding velocity and applied load
PublikacjaThis study investigates the contact temperatures caused by frictional heating of sliding parallel pairs. In this case the materials studied are a PTFE composite in contact with a high carbon steel plate. These materials are commonly used for industrial applications, in particular as the main contacting components within a scroll expander system. The expected contact temperature values are important to be quantified in order to...
-
Influence of the notch rounding radius on estimating the elastic notch stress concentration factor in a laser welded tee joint
PublikacjaIn recent years an increased interest of industry in sandwich-type metal structures can be observed. These structures consist of thin plates of 2.5 mm in thickness separated by stiffeners of different shapes and forms. Welds joining the plates and stiffeners are made on the outer side of the plates using laser welding technique. A locally focused source of heat causes the plate to melt creating a very narrow and elongated joint....
-
Parametric study of fluid flow and heat transfer over louvered fins of air heat pump evaporator
PublikacjaTwo-dimensional numerical investigations of the fluid flow and heat transfer have been carried out for the laminar flow of the louvered fin-plate heat exchanger, designed to work as an air-source heat pump evap- orator. The transferred heat and the pressure drop predicted by simulation have been compared with the corresponding experimental data taken from the literature. Two dimensional analyses of the louvered fins with varying...
-
Experimental and numerical identification of corrosion degradation of ageing structural components
PublikacjaThe study presents experimental and numerical identification of corrosion degradation of thin-walled structural components employing guided wave propagation. The steel structural components are subjected to through-thickness varying corrosion degradation levels. The developed approach using the non-destructive guided wave-propagation quantifies the equivalent average corrosion degradation level by exploring a limited number of...