Wyszukiwarka
Wyniki wyszukiwania dla: LOW NOISE ROAD SURFACE
-
Poroelastic Low Noise Road Surfaces
PublikacjaNoise is one of the most important problems related to road traffic. During the last decades, noise emitted by engine and powertrain of vehicles was greatly reduced and tyres became a clearly dominant noise source. The paper describes the concept of low noise poroelastic road surfaces that are composed with mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and are much more flexible...
-
Potential reduction of traffic noise by the means of increased fleet of electric vehicles using a combination of low-noise tyres and low-noise road surfaces
PublikacjaIn the future, the number of zero-emission vehicles like electric and plug-in hybrid vehicles (in electric mode) is expected to be a substantial part of the vehicle fleet. In Norway, such vehicles already account for approximately 20 % of all new cars sold. Since these vehicles emit negligible noise related to the power-train, the tyre/road noise is the dominating noise source. In the LEO project, tyres designed for such cars have...
-
Tyre/road noise reduction by a poroelastic road surface
PublikacjaLow noise road surfaces of existing types may in favourable cases and in new conditions provide up to 7 dB of noise reduction. For higher noise reductions, innovative solutions must be sought. Poroelastic road surfaces (PERS) may be such a solution, which currently is studied in the EU project PERSUADE. This paper presents results of trials with a PERS version prefabricated by one of the project partners. Tests were made in a laboratory...
-
Tyre/road noise reduction of poroelastic road surface tested in a laboratory
PublikacjaA so-called poroelastic road surface (PERS) is being developed in Europe. This contains a large percentage of rubber particles mixed with hard aggregate (stone and sand) and bound with polyurethane. This gives high air void content (around 30 %), high elasticity and smooth texture, all of which should give low noise properties. Inthis experiment anominally 30 mm thick sample of PERS was mounted on a steel drum. Various car tyres...
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublikacjaRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
Ultra Low Noise Poroelastic Road Surfaces
PublikacjaNoise is one of the most important environmental problems related to road traffic. During the last decades, the noise emitted by the engines and powertrains of vehicles was greatly reduced and tires became a clearly dominant noise source. The article describes the concept of low noise poroelastic road surfaces that are composed of mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and...
-
Biological hazards in low noise, poroelastic road surfaces
PublikacjaDrainage pavements as well as poroelastic pavements ("PERS") are a very efficient way to decrease traffic noise by reducing tire/road noise at the source as well as noise propagation over the road surface. Many noise generating mechanisms at the tire/road interface are very much reduced by road porosity (pipe resonance, "air pumping", Helmholtz resonance and the horn effect). A well-designed porous or poroelastic road surface may...
-
Low Noise Poroelastic Road Pavements Based On Bituminous Binder
PublikacjaTire/road noise is the dominant source of traffic noise. It depends both on the tire design and on the characteristics of road pavements as well as on the vehicles’ operating conditions. Due to the fact that conventional (pneumatic) car tires have almost reached the limits of their ability to further reduce their noisiness, it is widely believed that the additional reduction of tire noise will be possible mainly through modifications...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublikacjaThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Low noise poroelastic road pavements based on modified asphalt binder
PublikacjaTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublikacjaPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
Inhomogeneity of low-noise wearing courses evaluated by tire/road noise measurements using the close-proximity method
PublikacjaPerforming numerous analyses of tire/road noise measurements on low-noise pavements during the last several years, the authors observed significant inhomogeneity of the wearing course in numerous cases, while similar problems were almost non-existent when dense pavements were measured. Three main causes of low-noise pavement inhomogeneity can be defined. The first one is imperfections in the technology used for asphalt mix production...
-
Tyre/road noise of passenger car tyres, including tyres for electric vehicles - road measurements
PublikacjaThe paper presents the results from CPX measurements of tyre/road noise performed for selected passenger car tyres, including the tyres especially designed for electric vehicles. The tyres have been measured when rolling on several typical road surfaces in Norway and in Poland. In addition, the tyres have been measured on some very low noise road surfaces, such as a the poroelastic road surface (PERS). The measurement results...
-
PERS - QUIET ROAD SURFACE FOR URBAN AREAS
PublikacjaTraffic noise is one of the most important environmental problems in densely populated urban areas. At low speeds the tyre/road interaction dominates all other sources. It is anticipated that when electric and hybrid vehicles gain dominance in city traffic, the importance of tyre/road noise will still increase as electric engines are much less noisy than combustion engines. On the other hand, electric and hybrid urban vehicles...
-
Comparison of road and laboratory measurements of tyre/road noise
PublikacjaTyre/road noise is one of the major environmental problems related to road traffic. There are several measuring methods of tyre/road noise that may be carried out on the road (for example Coast-down and Close Proximity Method) or in the laboratory (Drum Method). Road measurements are preferred for evaluations of pavement properties while laboratory methods are mostly used to evaluate tyres. One of the biggest problems associated...
-
Tire/Road Noise On Poroelastic Road Surfaces - Results Of Laboratory Measurements
PublikacjaTire/road noise is the most important part of traffic noise for medium and high speed driving both in the case of passenger cars and trucks. The potential to make modification of tires that significantly reduce tire/road noise in nearly over, at least for conventional tires so the only promising action is to improve road pavements. One of the innovative solutions is poroelastic road pavement (PERS) that reduces airflow related...
-
Pavement ageing influence on tyre/road noise
PublikacjaRoad surface should be constructed in a way that ensures safe and comfortable traffic conditions, not only when it is newly paved but also during its entire lifetime. An important factor in the asphalt mixture design process is also the expected pavement durability and stability of pavement properties over time. In many countries, road surface starts to play a significant role in traffic noise reduction actions. Selecting a particular...
-
INFLUENCE OF MEASURING CONDITIONS ON TYRE/ROAD NOISE
PublikacjaA decisive factor for the development of tyres and road surfaces is the ability to conduct representative and reproducible measurements of selected characteristics related to the interaction of tyres and road surfaces. In terms of tyre/road noise measurements in Europe two methods described in ISO/FDIS 11819-2 and ECE Regulation No.117 are used. The latter is compulsory for assigning the tyre noise labels. The methodologies differ...
-
Temperature influence on tyre/road noise of selected tyres
PublikacjaAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
Temperature influence on tire/road noise evaluated by the drum method
PublikacjaAmbient air and road surface temperatures substantially affect the road vehicle noise emission. The temperature influence on tire/road noise depends mainly on tire-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tires. The correction procedures for temperature effect are still under consideration and preparation. Laboratory experiment was prepared to...
-
Temperature influence on tyre/road noise frequency spectra
PublikacjaThe correction for temperature effect on measured tyre/road noise is very important as it may be one of the main sources of errors in measurement results due to substantial influence of this parameter on obtained values. The latest version of the Technical Specification ISO/CD TS 13471-1 about Temperature Corrections contains a proposal of correction procedure for normalizing measured noise levels to a reference air temperature...
-
Sound quality metrics applied to road noise evaluation
PublikacjaRoad noise monitoring systems typically measure sound levels in specific time periods. The more insightful approach suggests to measure also the nature of noise. Sound quality of sounds such as car noise can be objectively evaluated by several parameters. One of them is psychoacoustic annoyance, described by loudness, tone color, and the temporal structure of sound. In this paper the assessment of several sound quality parameters, such...
-
Speed dependency of temperature effects on road traffic noise
PublikacjaRecently, a new literature review on the influence of temperature on tire/road noise became available, based on a compilation of large amounts of data from empirical research. This review showed that the effect of temperature is roughly double of that previously assumed and taken account of in international standards. This makes temperature one of the main sources of error in measurement results. Furthermore, it suggested that...
-
The contribution of tire/road noise to the overal noise of cars and motocycles
PublikacjaOmówiono wływ hałasu opon i hałasu jednostki napędowej na całkowity hałas generowany przez pojazd. Zaprezentowano opracowany w Katedrze pojazdów i Maszyn Roboczych PG program VENOM do symulacji halasu pojazdów w ruchu drogowym. Przy pomocy tego programu określono wpływ zmiennych warunków ruchu drogowego na hałas generowany przez pojazd. Uwzględnioino przyspieszanie na poszczególnych biegach, hamowanie z różnymi prędkościami oraz...
-
Tyre/road noise. Reference book.
PublikacjaKsiążka przedstawia zagadnienia związane z hałasem opon samochodowych poruszających się po nawierzchniach drogowych. Zawiera rozdziały poświęcone budowie opon, budowie nawierzchni drogowych, akustyce, mechanizmom generowania hałasu, wpływie czynników eksploatacyjnych i konstrukcyjnych na hałas opon, metodom pomiarowym, modelowaniu, metodom ograniczania hałasu opon, zagadnieniom prawnym i normalizacyjnym. Jest kompletnym przewodnikiem...
-
Reduction of road traffic noise by source measures — present and future strategies
PublikacjaThe current trend worldwide is less focused on reducing road traffic noise. This is in strong contrast to the severe impact of traffic noise to the general health and quality of life. A more holistic and combined strategy is needed. Current international rules and regulations regarding vehicles and tyres are not sufficient to reduce traffic noise levels in an effective way. Calculations show that these regulations will only yield...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublikacjaTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
Investigation of the road noise source employing an automatic noise monitoring station
PublikacjaThe paper presents a pilot investigation of noise source models in two selected localizations in the context of future dynamic noise map creation. The experiments were carried out using the automatic noise monitoring station engineered at the Multimedia Systems Departmentof the Gda´nsk University of Technology. The results of the noise measurements employing monitoring stations and its comparison to the reference values are depicted....
-
EVALUATION OF SOUND QUALITY FEATURES ON ENVIRONMENTAL NOISE EFFECTS – A CASE STUDY APPLIED TO ROAD TRAFFIC NOISE
PublikacjaThe paper shows a study on the relationship between noise measures and sound quality (SQ) features that are related to annoyance caused by the traffic noise. First, a methodology to perform analyses related to the traffic noise annoyance is described including references to parameters of the assessment of road noise sources. Next, the measurement setup, location and results are presented along with the derived sound quality features....
-
Modeling the effect of electric vehicles on noise levels in the vicinity of rural road sections
PublikacjaNumerous European countries experience a steady increase in the share of electric (EV) and hybrid electric (HEV) vehicles in the traffic stream. These vehicles, often referred to as low- or zero-emission vehicles, significantly reduce air pollution in the road environment. They also have a positive effect on noise levels in city centers and in the surroundings of low-speed roads. Nevertheless, issues related to modeling noise from...
-
ROSANNE Project: New Procedure for Noise Characterisation of Road Surfaces in Europe
PublikacjaROSANNE is a collaborative project in the 7th EU Framework Programme which aims at harmonising measurement methods for skid resistance, noise emission and rolling resistance of road pavements as a preparation for standardization. The project started in November 2013 and is developing and improving standards in the field of working group CEN/TC 227/WG 5. Regarding the influence of the pavement on the road traffic noise emission,...
-
Tire/road noise - generation, measurement, and abatement
PublikacjaPodano określenia i definicje dotyczące hałasu opon samochodowych. Omówiono mechanizmy generowania tego hałasu oraz zasady modelowania. Przedstawiono metody pomiaru hałasu opon oraz stosowane systemy pomiarowe. Podano normy dotyczące hałasu opon. Omówiono wpływ opony i nawierzchni na hałas generowany przez toczące się koło ogumione. Zaprezentowano koła kompozytowe oraz opony z bieżnikiem poroelastycznym generujące niski poziom...
-
Reduction of Tire Rolling Resistance by Optimization of Road Surfaces and Tires
PublikacjaDuring interaction between tire and road surface three very important phenomena are always in effect. One of them (very desirable) is friction that is important for traction, braking and cornering. Two other phenomena are not desirable at all, that is rolling resistance and noise. This paper discusses relations between road surface and tire parameters versus tire rolling resistance. Road surface texture, porosity, impedance, strength...
-
Rolling Resistance And Tire/Road Noise on Rubberized Asphalt Pavement In Poland
PublikacjaThe paper presents results of tire/road noise and rolling resistance measurements performed on stone-matrix asphalt (SMA) that contains rubberized asphalt developed and produced by the company in Poland. Bituminous binder was modified with polymer and additive of crumb rubber. First observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger car...
-
Rolling resistance and tyre/road noise on rubberised asphalt pavement in Poland
PublikacjaThe paper presents results of tyre/road noise and rolling resistance measurements performed on stone mastics asphalt (SMA) that contains rubberised asphalt, developed and produced by a refinery in Poland. Bituminous binder was modified with polymer and addition of crumb rubber. The first observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger...
-
Tyre/road noise measurements on ISO tracks using the modified CPX method
PublikacjaTyre rolling noise test method specified in the UNECE Regulation 117 is directly used in the Tyre Labelling Directive. Noise level specified on EU Tyre Label of each new tyre available on the European market was determined based on vehicle coast-by noise measurements performed on the standard reference road surface proscribed in the ISO 10844:2014. Available data from investigations by the vehicle and tyre industry and results...
-
Directivity of tire/road noise emission for selected tires and pavements
PublikacjaPraca pośwoęcona jest kierunkowości emisji hałasu opon i nawierzchni drogowych. Opony są dominującym źródłem haasu w pojaździe poruszającym się w typowych warunkach ruchu drogowego. Hałas ten nie jest bezkierunkowy jak to przyjmuje się w modelach obliczeniowych hałasu. Takie założenia wynikają z ograniczonej dostępności danych dotyczących kierunkowości i mogą prowadzić do niedokładności przy prognozowaniu hałasu drogowego. Praca...
-
Selective monitoring of noise emitted by vehicles involved in road traffic
PublikacjaAn acoustic intensity probe was developed measures the sound intensity in three orthogonal directions, making possible to calculate the azimuth and elevation angles, describing the sound source position. The acoustic sensor is made in the form of a cube with a side of 10 mm, on the inner surfaces of which the digital MEMS microphones are mounted. The algorithm works in two stages. The first stage is based on the analysis of sound...
-
Initial Field Validation of Poroelastic Pavement Made with Crumb Rubber, Mineral Aggregate and Highly Polymer-Modified Bitumen
PublikacjaTire/road noise in most driving conditions dominates other sources of traffic noise. One of the most efficient ways of reducing tire/road noise is to use the so-called “low noise pavement”. According to numerous studies, at present, poroelastic road pavement that is composed of rubber and mineral aggregate and polyurethane or bituminous binder gives the best noise reduction up to 12 dB. Unfortunately, there are many problems with...
-
Certification of vehicles used for tire/road noise evaluation by CPX method
PublikacjaJednym ze sposobów oceny hałasu opon i nawierzchni drogowych jest metda CPX polegająca na pomiarze hałasu w polu bliskim miejsca współpracy opony z nawierzchnią. Aby uzyskać wysoką dokładność pomiarów niezbędne jest ustanowienie procedur ustanowienie procedur certyfikacyjnych sprzętu pomiarowego a więc głównie pojazdu badawczego. Praca dotyczy procedur certyfikacyjnych wypracowanych przez Grupę Roboczą WG33 ISO/TC43/SC1 oraz w...
-
Tire/road noise measuring principles according to the Close Proximity Method
PublikacjaW pracy podano metody badania hałasu opon samochodowych. Omówiono przyczepy pomiarowe zbudowane w Politechnice Gdańskiej oraz systemy pomiarowe stosowane do pomiaru hałasu opon zgodnie z metodą CPX.
-
Road noise mapping in the city area: measurements compared to model-based estimations
PublikacjaThe paper presents an approach to the verification of noise prediction models in selected localization in the city of Gdansk. The experiments described include a comparison between environmentalmeasurement results performed in the terrain and the noise level prediction results. The NMPB-96 (Nouvelle Méthode de Prévision du Bruit) and Harmonoise models outcomes provide the subject ofthe analysis. The proposed solution of continuous...
-
Tyre/road noise measurements on ISO tracks according to the UNECE Regulation 117
PublikacjaWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on 3 ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance, and this directive is based on the measurement procedures defined in the UN ECE Reg.117. The same test car, test tyres and measurement equipment as well as personnel were used...
-
An in-depth look at the tire rubber hardness influence on tire/road noise measurements
PublikacjaWhen assessing the acoustic quality of a road pavement with the close-proximity (CPX) or the on-board sound intensity (OBSI) method, the rubber hardness of the reference tire substantially affects the measurement. Practical experience shows that measurement tires can get significantly harder within a single measurement season. This is why one would like to normalize measurements to a reference rubber hardness. The recently published...
-
Noise Generated by Tyres Designet for Electric Vehicles - Results of Laboratory Experiments
PublikacjaA few years ago, electric and hybrid vehicles were rarely seen on public roads and were considered more as exotic curiosities or even as a sign of extravagance than a practical means of transport. Nowadays the situation has changes significantly. This was caused both by the technical development and legislative actions, as well as the organizational nature promoting the purchace and use of low emission vehicles. Electric vehicles...
-
Comparison of pavement noise properties on selected road sections using different CPX measuring systems: self-powered vehicle and special test trailer
PublikacjaThe recently published ISO standard intended to measure the noise properties of road surfaces in a standardized method (ISO 11819-2:2017) precisely defines measurement procedure of the influence of road surface on traffic noise. According to it, two types of test vehicles may be utilized: a self-powered vehicle fitted with one or more test tyres and a trailer towed by a separate vehicle with one or more test tyres mounted on the...
-
Driver influence on tyre/road noise generated by vehicle in road traffic.Wpływ kierowcy na hałas generowany przez pojazd w ruchu drogowym.
PublikacjaW pracy omówiono wkływ stylu jazdy kierowcy oraz stanu technicznego wybranych zespołów pojazdu na jego hałas generowany w ruchu drogowym. Wpływ został przeanalizowany w aspekcie takich parametrów, jak: prędkość jazdy, obciążenie kół siłami wzdłużnumi i poprzecznymi, ciśnienie w ogumieniu, obciążenie pionowe kół, zbieżność i inne.
-
Poroelastic Road Surfaces - State of The Art
PublikacjaPoroelastic Road Surfaces (PERS) constitute a specific group of pavements containing a great amount of crumbled rubber. In most cases rubber aggregate constitutes about 20% of the mixture (by weight) and a polyurethane resin is used as a binder. As a result, PERS is characterized by a much higher elasticity than asphalt and a high porosity typical for drainage pavements. Due to this, tire/road noise is greatly reduced and on top...
-
The importance of the bottom layer in double-layer porous asphalt for noise reduction
PublikacjaDouble-layer porous asphalt concrete (DPAC) surfaces are generally considered to be the acoustically most effective low noise road surfaces ready for implementation. While DPAC used on highways in warm climates may have an average life of around 8 years, in Scandinavia with severe winter climate DPAC usually survive only about 3 years; partly due to wear of studded tyres. An ongoing project in Sweden, applying DPAC and single-layer...
-
Dawid Ryś dr hab. inż.
OsobySZKOLENIA Szkolenie dotyczące metodyki zarządzania projektami PRINCE 2. Certyfikat kwalifikacji. Szkolenie dotyczące Mikromechaniki Pracy Mieszanek Mineralno-Asfaltowych Szkolenie doyczące interakcji koło pojazdu-nawierzchnia
-
The best porous asphalt pavement in Sweden so far
PublikacjaIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Further development of the poroelastic road surface within the new Polish project SEPOR
PublikacjaRoad surfaces have a direct impact on noise generated by rolling tyres, the main and dominant source of noise of moving vehicles. Road surface texture, porosity and stiffness/elasticity govern the pavement contribution to tyre/road noise the most. An experimental PoroElastic Road Surface (PERS) is a wearing course with a high content of interconnected voids (pores) and with an elastic behavior due to the use of small particles...
-
LOW NOISE TIRES FOR HYBRID AND ELECTRIC VEHICLES
PublikacjaLow Emission Vehicles that are hybrid and electric cars may benefit from specially designed tires that are optimized for driving conditions typical for such vehicles. It is possible that in the future Low Emission Vehicles, especially passenger cars, will substitute conventional vehicles in all applications, however for the time being they are mostly used in urban and suburban areas. Urban traffic has a rather low demand for grip...
-
The influence of road surface unevenness on tyre rolling resistance
PublikacjaThe geometric characteristics of road surface substantially affect the interaction between tyre and road. Depending on pavement texture wavelength, the texture chiefly affects tyre/road friction, rolling resistance, interior and exterior noise, tyre wear, and ride comfort. The article presents results of investigations on the influence of road surface unevenness on the rolling resistance of passenger car and truck tyres. The tests...
-
HOW EFFICIENT IS NOISE LABELING OF TIRES?
PublikacjaSince 2012 all new tires in Europe must be labeled. The label contains general information about tire performance concerning rolling resistance (that corresponds to fuel economy), noise emission and wet grip (only for passenger car tires). Measurements of noise performance of tires must be performed according to the Annex 3 of the Regulation No 117 of the Economic Commission for Europe of the United Nations. The regulation specifies...
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublikacjaPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Final report on noise and rolling resistance
PublikacjaWork Package 6 deals with environmental impacts of PERS use, including noise and rolling resistance. This report covers preliminary noise tests performed in the laboratory and at the road test sites. The obtained results indicate that PERS material reduce noise considerably - up to 12 dB in comparison to SMA16 reference surface. Noise reduction properties are especially visible in the case of factory produced PERS slabs supplied...
-
Acoustic evaluation of road surfaces using different Close Proximity testing devices
PublikacjaAccording to the valid standard, Close Proximity (CPX) method intends to evaluate the influence of road surfaces on traffic noise. Measurements may be carried out with the use of a self-powered vehicle or a special test trailer equipped with testing tyre towed by another vehicle. Two different testing devices took part in the research organized in Poland in order to determine the ranking of road surfaces in terms of acoustic parameters....
-
Risks related to car fire on innovative Poroelastic Road Surfaces-PERS
PublikacjaTo reduce tyre/road noise, the concept of poroelastic road surfaces (PERS) was invented. PERS is a road surface material that is porous, and at the same time, it is flexible because of the substantial amount of rubber granulate content (from 20% to 85%). The rubber and stone particles are bound by polyurethane resin instead of bitumen. It was feared that in case of fire, because of the high content of rubber and polyurethane, there...
-
Road texture influence on tyre rolling resistance
PublikacjaTyre performance, one of the critical factors for vehicle users, is strongly related to theroad surface characteristics, most notably to the pavement texture. Phenomena that occur at the tyre/road interface affect tyre friction (skid resistance), rolling resistance, tyre wear and tyre/road noise. This article deals with relationship between surface texture and rolling resistance of light and heavy vehicle tyres. Mean profile depth...
-
Poroelastic Material for Urban Roads Wearing Courses
PublikacjaConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Poroelastic Material for Urban Roads Wearing Courses
PublikacjaConventional road materials used for producing wearing courses of roads are based on mineral aggregate and bituminous or Portland cement binders. The road materials must be optimized for different properties, including skid resistance, durability, rolling resistance and tire/road noise. Unfortunately, it seems that within classic technologies it is very difficult to achieve further reduction of tire/road noise. Innovative porous...
-
Performance of Noise Map Service Working in Cloud Computing Environment
PublikacjaIn the paper a noise map service designated for the user interested in environmental noise subject is presented. It is based on cloud computing. Noise prediction algorithm and source model, developed for creating acoustic maps, are working in cloud computing environment. In the study issues related to noise modeling of sound propagation in urban spaces are discussed with a special focus on road noise. Examples of results obtained...
-
The effect of tire aging on acoustic performance of CPX reference tires
PublikacjaReduction of tire/road noise is one of the biggest environmental challenges of road traffic. To reduce that noise it is necessary to perform acoustic measurements on the base of wellproven standard procedures. One method of measurements that is in common use, namely the Close Proximity Method (CPX), is described in standard ISO-DIS 11819-2. As this method is used to classify road surfaces regarding their influence on vehicle noise,...
-
Machine learning applied to acoustic-based road traffic monitoring
PublikacjaThe motivation behind this study lies in adapting acoustic noise monitoring systems for road traffic monitoring for driver’s safety. Such a system should recognize a vehicle type and weather-related pavement conditions based on the audio level measurement. The study presents the effectiveness of the selected machine learning algorithms in acoustic-based road traffic monitoring. Bases of the operation of the acoustic road traffic...
-
Machine learning applied to acoustic-based road traffic monitoring
PublikacjaThe motivation behind this study lies in adapting acoustic noise monitoring systems for road traffic monitoring for driver’s safety. Such a system should recognize a vehicle type and weather-related pavement conditions based on the audio level measurement. The study presents the effectiveness of the selected machine learning algorithms in acoustic-based road traffic monitoring. Bases of the operation of the acoustic road traffic...
-
Acoustic lifecycle study of the double-layer porous asphalt on E4 in Huskvarna, Sweden
PublikacjaIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed on the E4 motorway through the Swedish city Huskvarna. Earlier experience in Sweden indicated that it was feasible to obtain a high initial noise reduction but due to the widespread use of studded tires in winter, clogging and ravelling created losses of around 2 dB per year, with an expected acoustical lifetime of only 3 years. However, the improved...
-
Classifying type of vehicles on the basis of data extracted from audio signal characteristics
PublikacjaThe aim of this study is to find and optimize a feature vector for an automatic recognition of the type of vehicles, extracted form an audio signal. First, the influence of weather-based conditions of road surface on spectral characteristic of the audio signal recorded from a passing vehicle in close proximity to the road is discussed. Next, parameterization of the recorded audio signal is performed. For that purpose, the MIRtoolbox,...
-
Comparing traffic intensity estimates employing passive acoustic radar and microwave Doppler radar sensor
PublikacjaThe purpose of our applied research project is to develop an autonomous road sign with built-in radar devices of our design. In this paper, we show that it is possible to calibrate the acoustic vector sensor so that it can be used to measure traffic volume and count the vehicles involved in the traffic through the analysis of the noise emitted by them. Signals obtained from a Doppler radar are used as a reference source. Although...
-
Degradation of reference tyres used for CPX measurements
PublikacjaMeasurements of tyre/road noise using the Close Proximity Method are based on reference tyres that are described in ISO/TS 11819-3. The standard specifies two tyres, namely "P1" and "H1" that should be used during measurements. To be used for measurements each tyre must fulfill certain conditions that are listed in the standard. The conditions are related to the tread pattern depth and rubber hardness. During experiments performed...
-
Reduction of noise and rolling resistance by horizontal grinding of asphalt pavements
PublikacjaGrinding of cement concrete pavements to reduce unevenness and noise is common since a long time. Grinding is then made with wheels equipped with diamond blades rotating in the vertical plane. This creates narrow vertical/longitudinal grooves in the pavement. It is not applied to asphalt pavements. In this paper an alternative type of grinding is studied. In this case plates with diamond heads rotate in the same plane as the pavement,...
-
Experimental validation of the rolling resistance measurement method including updated draft standard
PublikacjaThe main objective of ROSANNE is the harmonisation and standardisation of the measurement of skid resistance, noise emission and rolling resistance of road pavements. Regarding rolling resistance characterisation, a draft for standardization of a harmonized procedure for classification of road surfaces across Europe has been prepared within WP3 (deliverable 3.5). The procedure deals with the direct measurement on real roads of...
-
COMPARISON OF NOISE EMISSION OF HCT AND CLASSIC VEHICLE COMBINATIONS FOR TIMBER TRANSPORTATION IN SWEDEN
PublikacjaBy means of a special simulation tool, the noise emission of a high-capacity heavy vehicle (11 axles) was compared to that of a classic heavy vehicle (a truck-dolly-semitrailer with 8 axles). The two cases are designated “Extended vehicle” versus “Classic vehicle” in this study, having total lengths of 34 and 25 m, respectively. The Classic vehicle represents the most common articulated heavy vehicle configuration for transport...
-
Creating dynamic maps of noise threat using pl-grid infrastructure; materiały konferencyjne
PublikacjaThis paper presents functionality and operation results of the system for creating dynamic maps of noise thread with the use of the PL-Grid infrastructure integrated with distributed sensors network for measuring, modeling and rendering noise level distribution. The work presented provides a demonstration of the services being prepared within the PLGrid Plus project. Specific computational environments, so called domain grids,...
-
The EU Tyre Noise Label: The problem with measuring the noise level of only a few of all tyre variants
PublikacjaThe STEER project, described in another Inter-Noise 2022 paper, has evaluated the performance of the noise label of the European tyre label. The major finding was that uncertainties of the tyre/road noise measurements were higher than should be accepted. One of the worst uncertainty sources was found to be the common practice to measure only some tyres of all sizes or variants within a tyre line, to save money. Generally, only...
-
Design of poroelastic wearing course with the use of direct shear test
PublikacjaPoroelastic Road Surfaces (PERS) are characterized by porous structure with at least 20% of air void content and stiffness almost 10 times lower than typical asphalt course. Such properties enable noise reduction up to 12 dB in comparison to SMA 11 mixture. However, the main disadvantage of previously used poroelastic mixtures, based on resin type binders, was their low durability, which resulted in raveling and delamination from...
-
Creating Dynamic Maps of Noise Threat Using PL-Grid Infrastructure
PublikacjaThe paper presents functionality and operation results of a system for creating dynamic maps of acoustic noise employing the PL-Grid infrastructure extended with a distributed sensor network. The work presented provides a demonstration of the services being prepared within the PLGrid Plus project for measuring, modeling and rendering data related to noise level distribution in city agglomerations. Specific computational environments,...
-
Marek Pszczoła dr hab. inż.
OsobyI am a Faculty member (Department of Highway and Transportation Engineering) at the Faculty of Civil and Environmental Engineering, Gdansk University of Technology, Poland). My main research interests include: low-temperature properties of asphalt mixtures, low temperature cracking assessment of pavement structures, road materials properties, thermal stress analysis, design of pavement structures, airfield design and analysis....
-
Application of autoencoder to traffic noise analysis
PublikacjaThe aim of an autoencoder neural network is to transform the input data into a lower-dimensional code and then to reconstruct the output from this code representation. Applications of autoencoders to classifying sound events in the road traffic have not been found in the literature. The presented research aims to determine whether such an unsupervised learning method may be used for deploying classification algorithms applied to...
-
Improving the CPX method by specifying reference tyres and including corrections for rubber hardnes and temperature
PublikacjaRecently completed work in the EU project ROSANNE and in working group ISO/TC43/SC1/WG33 has allowed substantial improvements to measurements made by the Close-Proximity (CPX) method, intended for measurement of noise properties of road surfaces.The paper summarizes the experimental work and describes the conclusions and implementation in ISO/FDIS 11819-2 (CPX method) and in the supporting ISO (draft) Technical Specifications 11819-3...
-
Economical methods for measuring road surface roughness
PublikacjaTwo low-cost methods of estimating the road surface condition are presented in the paper, the first one based on the use of accelerometers and the other on the analysis of images acquired from cameras installed in a vehicle. In the first method, miniature positioning and accelerometer sensors are used for evaluation of the road surface roughness. The device designed for installation in vehicles is composed of a GPS receiver and...
-
Scientific research in the Department of Machine Design and Automotive Engineering
PublikacjaShort descriptions of various research subjects taken up at the Department of Machine Design and Automotive Engineering are included in the paper. The subjects cover a wide range of bearing systems and tribology research and the research on tires and road surfaces. A third field of activity is biomedical engineering – with the attempts to improve methods of modelling biological materials in FEM calculations. The Department has...
-
Investigation of Acoustic Properties of Poroelastic Asphalt Mixtures in Laboratory and Field Conditions
PublikacjaMeasures for the improvement of acoustic conditions in the vicinity of roads include the construction of pavement structures with low-noise surfaces with optimal macrotexture and the highest possible sound absorption coefficient. Laboratory evaluation of acoustic properties of a designed asphalt mixture before its placement in the pavement is a good solution. Currently, the most popular method for the determination of the sound...
-
Detection of the Incoming Sound Direction Employing MEMS Microphones and the DSP
PublikacjaA 3D acoustic vector sensor based on MEMS microphones and its application to road traffic monitoring is presented in the paper. The sensor is constructed from three pairs of digital MEMS microphones, mounted on the orthogonal axes. Signals obtained from the microphones are used to compute sound intensity vectors in each direction. With this data, it is possible to compute the horizontal and vertical angle of an incoming sound....
-
WSN for intelligent street lighting system
PublikacjaIn this article authors propose to apply WSN to intelligent street lighting system. As a result of such a combination one obtains a system designed to increase functionality of light installations for a wide range of applications and introduce a platform for new additional services, which meets current and future user needs. The system is composed of WSN nodes integrated with light sources based on high power LED diodes, which...
-
Noise measurements on low noise pavements - problems with inhomogeneity of wearing course
PublikacjaDuring the last several years, when performing numerous CPX noise measurements on low noise pavements,significant inhomogeneity of the wearing course was observed in numerous cases. Similar problems were almost not existing regarding to the dense pavements.In general three main reasons of inhomogeneity can be defined. The first one are imperfections in technology of production of a asphalt mix or/and errors made already during...
-
Detection of Water on Road Surface with Acoustic Vector Sensor
PublikacjaThis paper presents a new approach to detecting the presence of water on a road surface, employing an acoustic vector sensor. The proposed method is based on sound intensity analysis in the frequency domain. Acoustic events, representing road vehicles, are detected in the sound intensity signals. The direction of the incoming sound is calculated for the individual spectral components of the intensity signal, and the components...
-
Cycling as a Sustainable Transport Alternative in Polish Cittaslow Towns
PublikacjaIt is well known that growing motor traffic in urban areas causes air pollution and noise which affects the environment and public health. It is hardly surprising then that cycling should be used as an alternative mode of transport, not just in major cities but also in smaller ones including those that are members of the Cittaslow network. Their approach is based on sustainable development, care for the environment and transport...
-
Representativity of ISO test track surface based on controlled pass-by measurements
PublikacjaWithin the Polish-Norwegian research project ELANORE, a limited Round Robin Test has been performed on four ISO tracks in Northern Europe. The basic objective of the project is to improve the EU directive on labelling of tyres for noise and rolling resistance. This directive is based on the measurement procedures proscribed in the UNECE Reg.117. Measurements on 3 ISO tracks were performed in 2021 and presented at InterNoise 2022....
-
Assessment of Supercapacitor’s Quality by Means of Low Frequency Noise
PublikacjaLow frequency noise is a well-known tool for quality and reliability assessment of electronic devices. This phenomenon is observed in different electrochemical devices as well (e.g., smart windows, electrochemical corrosion processes). Thus, we can assume that the same tool can be used to asses quality of supercapacitors. Their quality is usually determined only by capacitance and/or equivalent series resistance (ESR), or impedance....
-
Dedicated power supply subsystem for ultra-low noise preamplifiers
PublikacjaIn field of electronics there is need for low-noise amplifiers. Noise have the most important influence on analog circuits. Therefore exist necessity to develop new ultra-low noise power supplies, which can cooperate with specified amplifiers and preamplifiers. It is very common that professional power supplies are very expensive and still have disadvantages. This paper proposes simple and inexpensive solution, which fulfill specific...
-
Visual Traffic Noise Monitoring in Urban Areas
PublikacjaThe paper presents an advanced system for railway and road traffic noise monitoring in metropolitan areas. This system is a functional part of a more complex solution designed for environmental monitoring in cities utilizing analyses of sound, vision and air pollution, based on a ubiquitous computing approach. The system consists of many autonomous, universal measuring units and a multimedia server, which gathers, processes and...
-
Counting and tracking vehicles using acoustic vector sensors
PublikacjaA method is presented for counting vehicles and for determining their movement direction by means of acoustic vector sensor application. The assumptions of the method employing spatial distribution of sound intensity determined with the help of an integrated 3D intensity probe are discussed. The intensity probe developed by the authors was used for the experiments. The mode of operation of the algorithm is presented in conjunction...
-
Road surface roughness estimation employing integrated position and acceleration sensor
PublikacjaAssessment of a surface quality being an essential task for the authorities supervising the roads provides the subject of the paper. Information about riding quality of a pavement, important for drivers, both in terms of their comfort and safety is collected during experiments employing mobile sensors. The paper describes the use of a miniature position and acceleration sensor for evaluation of the roughness of the road surface....
-
The impact of the Tri-City Ring Road on surface water of small endorheic wetlands
PublikacjaThe paper presents the results of the impact of the Tri-City Ring Road on small endorheic catchment basins. Particular attention was paid to pollution discharged from the road to the surface water, as well as changes in hydrological conditions in the vicinity of the road. In the study, surface water samples were analysed in terms of their electrolytic conductivity, pH and content of major minerals. GIS was also used to study transformation...
-
A review of design approaches for the implementation of low-frequency noise measurement systems
PublikacjaElectronic noise has its roots in the fundamental physical interactions between matter and charged particles, carrying information about the phenomena that occur at the microscopic level. Therefore, Low-Frequency Noise Measurements (LFNM) are a well-established technique for the characterization of electron devices and materials and, compared to other techniques, they offer the advantage of being non-destructive and of providing...
-
Assessment of Fuel Cells’ State of Health by Low-Frequency Noise Measurements
PublikacjaWe proposed applying low-frequency (flicker) noise in proton-exchange membrane fuel cells under selected loads to assess their state of health. The measurement set-up comprised a precise data acquisition board and was able to record the DC voltage and its random component at the output. The set-up estimated the voltage noise power spectral density at frequencies up to a few hundred mHz. We observed the evolution of the electrical...
-
Low-frequency noise in ZrS3 van der Waals semiconductor nanoribbons
PublikacjaWe report the results of the investigation of low-frequency electronic noise in ZrS3 van der Waals semiconductor nanoribbons. The test structures were of the back-gated field-effect-transistor type with a normally off n-channel and an on-to-off ratio of up to four orders of magnitude. The current–voltage transfer characteristics revealed significant hysteresis owing to the presence of deep levels. The noise in ZrS3 nanoribbons...
-
Low-Temperature Requirements for Bitumen in Central East European Road Construction
PublikacjaThe paper presents the proposition of special assessment of lowtemperature requirements for bitumens in the region of Central and Eastern Europe where there is a moderate transitional area from sea to the continental type of climate. The results of the research program conducted on the road neat bitumens, Styrene-Butadiene-Styrene polymer and polymer-rubber modified bitumen, and multigrade bitumen types were presented and discussed....
-
Shipping Low Frequency Noise and Its Propagation in Shallow Water
PublikacjaOne of the most significant factor influencing acoustical climate of the sea is underwater noise generated by moving ships. If the considered sea area has features of the shallow water, namely the wave frequency fulfils relation f < 10c/h, where c denotes phase speed of sound, and h is depths of the sea, then in certain distance from the wave source specific image of sound pressure distribution in the mean of wave modes appears....