Filtry
wszystkich: 1799
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: STEEL-CONCRETE SPECIMEN
-
Corrosion behavior of concrete produced with diatomite and zeolite exposed to chlorides
PublikacjaChloride induced reinforcement corrosion is widely accepted to be the most frequent mechanism causing premature degradation of reinforced concrete structures. The electrochemical impedance of reinforcing steel in diatomite- and zeolite-containing concrete exposed to sodium chloride was assessed. Chemical, physical and mineralogical properties of three concrete samples (20% diatomite, 20% zeolite, and a reference containing neither)...
-
Analiza kosztów i czasu budowy domu jednorodzinnego w technologii drewna krzyżowo klejonego CLT
Publikacja-
-
FE analysis of support-specimen interaction of compressive experimental test
PublikacjaThe objective of this work is to investigate the support-specimen interaction during the compressive experimental testing of stiffened plates. The interaction is analyzed employing the nonlinear Finite Element Method using the commercial software ANSYS. The connection between the stiffened plate and testing supports is modelled with the use of contact elements, where several possible interaction scenarios are investigated, and...
-
Remote sensing and photogrammetry techniques in diagnostics of concrete structures
PublikacjaRecently laser scanning technologies become widely used in many areas of the modern economy. In the following paper authors show a potential spectrum of use Terrestrial Laser Scanning (TLS) in diagnostics of reinforced concrete elements. Based on modes of failure analysis of reinforcement concrete beam authors describe downsides and advantages of adaptation of terrestrial laser scanning to this purpose, moreover reveal under which...
-
Optical flow method for measuring deformation of soil specimen subjected to torsional shearing
PublikacjaIn this study optical flow method was used for soil small deformation measurement in laboratory tests. The main objective was to observe how the deformation distributes along the whole height of cylindrical soil specimen subjected to torsional shearing (TS test). The experiments were conducted on dry non-cohesive soil specimens under two values of isotropic pressure. Specimens were loaded with low-amplitude cyclic torque to analyze...
-
Finite element models used in diagnostics of transverse cracks in bridge approach pavement
Dane BadawczeTransverse cracks in the asphalt pavement were observed on bridge structures next to single-module expansion joints with a 5 meter approach slab set at the depth of 1 m. The finite element (FE) models of the approach pavement were created to investigate the reasons of premature cracking and crack initiation mechanism over the back edge of the abutment...
-
Unstability of 4-CMC in human serum specimen
Publikacja -
Standard and modified falling mass impact tests on preplaced aggregatefibrous concrete and slurry infiltrated fibrous concrete
PublikacjaAlthough several studies have been conducted to evaluate the impact response of concrete using theAmerican Concrete Institute (ACI) 544-2R falling mass impact test, the variations in test results are themain drawback of this testing method. This study aims to reduce the variations in experimental impacttest results by introducing two simple test setup modifications; (1) using coarse or fine aggregate bed-ding as an alternative...
-
Complex Steel Structures 2022
Kursy Online -
Modelling reinforced concrete beams under mixed shear-tension failure with different continuous FE approaches
PublikacjaThe paper presents quasi-static numerical simulations of the behaviour of short reinforced concrete beams without shear reinforcement under mixed shear-tension failure using the FEM and four various constitutive continuum models for concrete. First, an isotropic elasto-plastic model with a Drucker-Prager criterion defined in compression and with a Rankine criterion defined in tension was used. Next, an anisotropic smeared crack...
-
Assessment of crack resistance of S355J2+N steel according to SEP 1390 standard
PublikacjaThe aim of the study was to evaluate the weldability of S355J2+N steel by bending test according to SEP 1390. In the specimen from S355J2+N steel 3 external cracks were found, 1 of which were stopped in the fusion line and 2 in heat affected zone. Results of bending test for investigated grade of steel are positive.
-
EXPERIMENTAL EVALUATION OF DLC/STEEL SLIDING CONTACTS’ OPERATIONAL ENVELOPE
PublikacjaIn an industrial project concerning sliding bearings, a sliding pair was selected of high alloy steel vs. industrial grade DLC coated high alloy steel as a basis for an innovative design of high performance sliding bearings lubricated with a synthetic oil for use in geared transmission units. The development process required credible data on the ultimate resistance of the sliding pair to very high contact stress. An experimental...
-
Concrete Operators
Czasopisma -
Debonding Detection in Reinforced Concrete Beams with the Use of Guided Wave Propagation
PublikacjaOne of the most frequent damage of the reinforced concrete structures is debonding between steel bar and concrete cover. In the case of debonding occurrence not only the strength of the structure decreases, but also it is more vulnerable to corrosion damages. For this reason fast and effective methods of debonding detection in an early stage of its development need a significant boost. The paper presents analytical and experimental...
-
Experimental investigations on concrete beams reinforced with CFRP lamellas
PublikacjaPaper presents experimental investigation made on two concrete beams reinforced with internal Carbon Fibre Reinforced Polymer (CFRP) lamellas (i.e. strips, bands). The reinforcement geometrical arrangement was similar as in normal concrete beams reinforced with steel bars and stirrups. The beams were destroyed by the shear forces, as intended. Obtained load-carrying capacities were lower as expected: below 40% of a calculated value....
-
Stan graniczny nośności dźwigara żelbetowego mostu na zginanie według norm PN-EN 1992-2 oraz PN-S-10042:1991
PublikacjaPraca włącza się w bogaty w ostatnich latach w krajowym piśmiennictwie nurt porównań dwóch generacji norm projektowania mostów z betonu: polskiej - wycofanej, aczkolwiek powszechnie stosowanej oraz europejskiej – wciąż jeszcze wdrażanej do praktyki projektowej. Nowością w stosunku do dotychczasowych publikacji polskich jest szersze ujęcie różnic pomiędzy obydwiema generacjami norm. Poza rozpatrywanymi przez wielu autorów różnicami...
-
COLD CRACKING OF S460N STEEL WELDED IN WATER ENVIRONMENT
PublikacjaThis paper shows results of weldability testing of fine-grained high -strength low- alloy S460N steel welded in water environment by covered electrodes. The tests were carried out by using the CTS test specimens with fillet welds. Four specimens were welded under water and one specimen in air. Welded joints were subjected to non-destructive visual and penetration tests. The accepted joints were then subjected to macroscopic and...
-
Influence of stirrups in a concrete shell on strengthening reinforced concrete column
PublikacjaTwelve concrete columns, with a 150x150mm square section and three columns with a circular section (d=200mm), are tested to investigate the effect of strengthening by RC jacket. Based on a confined concrete model for axial static loading, an analytical methods, reported in the literature are proposed to predict the behavior of columns with RC jacket. The results support the conception that the effect of strengthening depends...
-
Influence of selected additives and admixtures on underwater concrete and the environment
PublikacjaThe intensive civilization development has an influence on searching for new possibilities connected with extension of city agglomerations, both the areas of flat building and the industrial areas. One of the most interesting solution is to use water reservoirs, rivers and sea areas. The extension of buildings has an influence on building materials, especially hydrotechnical, which means development of production of hydrotechnical...
-
Experiments and calibration of a bond-slip relation and efficiency factors for textile reinforcement in concrete
PublikacjaTextile reinforcement yarns consist of many filaments, which can slip relative each other. At modelling of the global structural behaviour, interfilament slip in the yarns, and slip between the yarns and the concrete can be considered by efficiency factors for the stiffness and strength of the yarns, and by applying a bond-slip relation between yarns and concrete. In this work, an effective and robust method for calibration of...
-
Complex Steel Structures (2022/23)
Kursy Online -
Complex Steel Structures (2023/24)
Kursy Online -
Experimental tests of reinforced concrete deep-beams
PublikacjaThe paper presents results of experimental research of the reinforced concrete deep beam with a spatial arrangement. Tested structural elements consist of the cantilever deep beam loaded on the height and transverse deep beam with hanging on it another one. The analysis includes crack morphology, effort of steel and load distribution. The article verified effectiveness of two different kind of reinforcement in both tested deep...
-
Simple empirical formula to estimate the main geomechanical parameters of preplaced aggregate concrete and conventional concrete
PublikacjaPreplaced aggregate concrete (PAC) or two-stage concrete is a specific type of concrete successfully employed in many projects including underwater concrete structures, massive concrete structures, structures made of reinforced concrete, and improvement of concrete structures. PAC is significantly different than the conventional concrete. In this type of concrete, aggregates are initially poured into the mold, the voids between...
-
Evaluation of Mechanical Properties of Two-Stage Concrete and Conventional Concrete Using Nondestructive Tests
PublikacjaDifferent types of concrete mixtures are used as building materials. The manufacturing process of two-stage concrete (TSC) differs from that of conventional concrete. This study investigated conventional mechanical properties derive empirical relations for estimation of the mechanical parameters of TSC and conventional concrete mixtures. TSC was used to prepare 216 specimens and conventional concrete was used to prepare 108 specimens...
-
Deterioration and Protection of Concrete Elements Embedded in Contaminated Soil: A Review
PublikacjaCoating materials are considered one of the most antique materials of human civilization; they have been used for decoration and the protection of surfaces for millennia. Concrete structures—due to their permanent exposure to different types of environments and contaminants—require the use of coatings that contribute to its preservation by reducing the corrosion of its components (steel and aggregates). This article intends to...
-
Concrete-filled FRP tubular members in marine and bridge structures
PublikacjaConcrete core of the concrete-filled tubes (CFTs) with circular cross-section is in the case of an axial compression subjected to a spatial state of compressive stresses. This state leads to enhancement in the concrete strength. The enhancement is utilized in Eurocode 4 design procedures for CFSTs (i.e. CFTs with tube made of steel). The structural design of CFFTs (i.e. CFTs with tube made of Fibre Reinforced Polymer - FRP) is...
-
Steel in Translation
Czasopisma -
Deformations of the steel schell of a vertical cylindrical tank caused by underpressure
PublikacjaUnderpressure in a tank with a fixed roof may arise in the final stage of its construction as well as during its usage. This article presents stages of deformations of the tank shell and their development from the occurrence of the first deformation to either removal of the causes of underpressure or cracking of the steel shell.
-
The Application of Fibres from Recycled Postconsumer Tyres for Concrete Reinforcement
PublikacjaPoland as a Member State is obliged to implement the EU specific environmental legislation focused on the reduction, transport and treatment of waste. The Landfill Directive prohibited the landfilling of whole tyres and their by-products. Although the EU Directive of Waste limits the use of tyres as secondary fuel, Poland is still the EU leader in burning tyres in cement kilns. Post-consumer tyres are utilised in a number of...
-
Load capacity of steel-aluminium brackets under static and cyclic laboratory tests
PublikacjaThe aim of the research is the laboratory investigation of steel-aluminium brackets employed to fasten lightweight curtain walls to building facilities. Static pressure, suction forces, and cyclic loads parallel to end plates (horizontal – to simulate wind influence) were applied in the study. The steel-aluminium brackets were tested on a reinforced concrete substrate made of C30/37 concrete class to simulate the real working conditions....
-
A novel formulation of 3D spectral element for wave propagation in reinforced concrete
PublikacjaThe paper deals with numerical simulations of wave propagation in reinforced concrete for damage detection purposes. A novel formulation of a 3D spectral element was proposed. The reinforcement modelled as the truss spectral element was embedded in the 3D solid spectral finite element. Numerical simulations have been conducted on cuboid concrete specimens reinforced with two steel bars. Different degradation models were considered...
-
Reinforced concrete thin wall dome after eighty years of operation in maritime climate environment
PublikacjaThe paper presents a description of the construction elements of the Gdynia Seaport main hall dome. Firstly, it provides information about the technical condition of the dome’s structure. Secondly, it examines the strength analysis of the thin-walled reinforced concrete dome covering. Throughout the last 80 years the building has been exposed to an unfavourable marine climate. The analysis of the state of stress and deformations...
-
Mechanical and structural behavior of high-strength low-alloy steel pad welded by underwater wet welding conditions
PublikacjaThe aim of the paper was to determine the metallurgical and mechanical behaviors of a high-strength low-alloy (HSLA) steel pad-welded specimen used in the structures of industrial and naval parts. Then to predict the metallurgical consequences (nature of the phases present) and the mechanical properties (hardness and impact strength) of the pad-welded steel obtained by underwater wet welding with different heat input values. The...
-
Mechanical Performance and Environmental Assessment of Sustainable Concrete Reinforced with Recycled End-of-Life Tyre Fibres
PublikacjaThe presented research’s main objective was to develop the solution to the global problem of using steel waste obtained during rubber recovery during the tire recycling. A detailed comparative analysis of mechanical and physical features of the concrete composite with the addition of recycled steel fibres (RSF) in relation to the steel fibre concrete commonly used for industrial floors was conducted. A study was carried out using...
-
RMS-based damage detection in reinforced concrete beams: numerical simulations
PublikacjaImage-based damage detection methods using guided waves are well known and widely applied approaches in structural diagnostics. They are usually utilized in detection of surface damages or defects of plate-like structures. The article presents results of the study of applicability of imaging wave-based methods in detection in miniscule internal damage in the form of debonding. The investigations were carried out on numerical models...
-
Influence of Material Thickness on the Ductile Fracture of Steel Plates for Shipbuilding
PublikacjaIn the shipbuilding industry, the risk of brittle fractures is relatively high because some units operate in arctic or subarcticzones and use high thickness (up to 100 mm) steel plates in their structures. This risk is limited by employing certifiedmaterials with a specific impact strength, determined using the Charpy method (for a given design temperature) and byexercising control over the welding processes (technology qualification,...
-
Concrete mix design using machine learning
PublikacjaDesigning a concrete mix is a process of synthesizing many components, it is not a simple process and requires extensive technical knowledge. The design process itself focuses on obtaining the required strength of concrete. Very often designing a concrete mix takes into account the need to maintain the proper water-demand and frost-resistance features. The parameters that influence the concrete class most significantly are the...
-
Investigations on fracture in reinforced concrete beams in 3-point bending using continuous micro-CT scanning
PublikacjaThis study explores a fracture process in rectangular reinforced concrete (RC) beams subjected to quasi-static three-point bending. RC beams were short and long with included longitudinal reinforcement in the form of a steel or basalt bar. The ratio of the shear span to the effective depth was 1.5 and 0.75. The focus was on the load–deflection diagram and crack formation. Three-dimensional (3D) analyses of the size and distribution...
-
Machine Learning Techniques in Concrete Mix Design
PublikacjaConcrete mix design is a complex and multistage process in which we try to find the best composition of ingredients to create good performing concrete. In contemporary literature, as well as in state-of-the-art corporate practice, there are some methods of concrete mix design, from which the most popular are methods derived from The Three Equation Method. One of the most important features of concrete is compressive strength, which...
-
The lethal effect of hydrotechnical concrete on freshwater Bivalvia
PublikacjaMost hydrotechnical buildings under construction demand the concrete mixture to be set directly under water. The main reason for such a procedure is to limit the washing away of the the concrete binding mixture and to increase the efficiency of organisation of work so as to ensure continuity in concreting. The impact on the aquatic environment of recent developments in concrete technology and the use of new components has not yet...
-
Time evolution of Electrochemical Impedance spectra of cathodically protected steel in artificial seawater
PublikacjaUsability of Electrochemical Impedance Spectroscopy data for better cathodic protection control was investigated. Carbon steel – S235JR2 grade specimen were exposed in artificial seawater environment. Samples were polarized and their potentials corresponded to four different cathodic protection degrees. Time evolution of Electrochemical Impedance spectra was investigated. Goodness of fit function (X2) was analysed in terms of proper...
-
A study on fibre-reinforced concrete elements properties based on the case of habitat modules in the underwater sills
PublikacjaHydrotechnical constructions are mostly objects functioning in extreme conditions and requiring a custom-made construction project. In the case of using prefabricated elements, it is required to develop production, transport, assembly, conservation and repair technology. Concerning the problem of concrete cracks, modern repair systems allow positive effects to be achieved in many cases of concrete elements repair. In this work...
-
COMPUTER-AIDED CONSTRUCTION AT DESIGNING REINFORCED CONCRETE COLUMNS AS PER EC
PublikacjaThe article presents the author’s computer program for designing and dimensioning columns in reinforced concrete structures taking into account phenomena affecting their behaviour and information referring to design as per EC. The computer program was developed with the use of C++ programming language. The program guides the user through particular dimensioning stages: from introducing basic data such as dimensions, concrete...
-
Shear resistance of low height precast concrete lintels
PublikacjaThe scope of the paper is to investigate analytically and determine experimentally the shear resistance of low height reinforced precast concrete lintels. The chosen procedures included in national and international standards applied for the design of structural concrete elements to an estimation of shear behaviour of reinforced concrete elements are described. The characteristic and designed shear strength of precast concrete...
-
Debonding Size Estimation in Reinforced Concrete Beams Using Guided Wave-Based Method
PublikacjaThe following paper presents the results of the theoretical and experimental analysis of the influence of debonding size on guided wave propagation in reinforced concrete beams. The main aim of the paper is a development of a novel, baseline-free method for determining the total area of debonding between steel rebar embedded in a concrete cover on the basis of the average wave velocity or the time of flight. The correctness of...
-
Comparison of Different Measurement Techniques as Methodology for Surveying and Monitoring Stainless Steel Chimneys
PublikacjaThe measurement of a chimney axis is an engineering geodesy task. These measurements allow to assess the technical condition of chimneys and are usually carried out for reinforced concrete chimneys. When measuring high chimneys, the main problem may be the need to go a long distance to take a measurement. The surface of the chimney can also be problematic because it can absorb so much light from the range finder that total station...
-
Fatigue fracture morphology of AISI H13 steel obtained by additive manufacturing
PublikacjaThe paper focuses on researching the effect of fatigue loading on metallic structure, lifetime, and fracture surface topographies in AISI H13 steel specimens obtained by selective laser melting (SLM). The topography of the fracture surfaces was measured over their entire area, according to the entire total area method, with an optical three-dimensional surface measurement system. The fatigue results of the SLM 3D printed steel...
-
Detection of debonding in reinforced concrete beams using ultrasonic transmission tomography and hybrid ray tracing technique
PublikacjaThis paper concerns inspection of reinforced concrete elements, with particular emphasis on assessing the quality of the adhesive connection between steel and concrete. A novel theoretical model was developed to determine the paths of transmitted, refracted and reflected elastic waves as well as a creeping wave propagated along the inclusion surface. Imaging the internal structure of tested beams was based on wave propagation measurements...
-
CEMENT & CONCRETE COMPOSITES
Czasopisma -
CEMENT CONCRETE AND AGGREGATES
Czasopisma -
Advances in Concrete Construction
Czasopisma -
Nordic Concrete Research
Czasopisma -
Chemical and Mechanical Properties of 70-Year-Old Concrete
PublikacjaThe aim of this research is to determine the durability and strength of concrete continuous footing based on the chosen mechanical, physical, and chemical properties of the concrete. The presented investigations constitute some opinions from experts on the bearing capacity of concrete continuous footing and the possibilities of carrying additional loads and extended working life. The cylindrical specimens were taken from continuous...
-
Numerical simulation of hardening of concrete plate
PublikacjaThe paper presents a theoretical formulation of concrete curing in order to predict temperature evolution and strength development. The model of heat flow is based on a well-known Fourier equation. The numerical solution is implemented by means of the Finite Difference Method. In order to verify the model, the in situ temperature measurements at the top plate of a road bridge were carried out. A high agreement between numerical...
-
Properties of Old Concrete Built in the Former Leipziger Palace
PublikacjaThis research aims to determine the mechanical, chemical, and physical properties of old concrete used in the former Leipziger Palace in Wrocław, Poland. The cylindrical specimens were taken from the basement concrete walls using a concrete core borehole diamond drill machine. The determination of the durability and strength of old concrete was based on specified chosen properties of the old concrete obtained through the following...
-
Review of titanium and steel welding methods
PublikacjaThe paper presents review of methods of titanium and steel welding. On basis of professional literature it was stated that titanium can be joined with steel by means of explosive welding or brazing.Joining titanium with steel by TIG welding and friction welding methods is possible with the use of copper and tantalum or vanadium interlayer.
-
Experimental study on earthquake-induced pounding between steel structures
PublikacjaPounding between adjacent structures has been repeatedly observed during major earthquakes. The phenomenon may cause some local damage at the points of interactions, it may also lead to substantial destruction, permanent deformations or total collapse of colliding structures. The effects of earthquake-induced structural pounding have been studied for more than three decades now. However, most of the studies concerned masonry as...
-
Ultrasound monitoring for evaluation of damage in reinforced concrete
PublikacjaThe paper deals with automated monitoring of damage evolution in concrete elements subjected to three-point bending tests. The monitoring is based on the nonlinear interactions of traveling ultrasonic waves with micro-crack zones inside the concrete specimens and surface-breaking cracks. The developed procedure assumes semi-continuous ultrasonic testing during the element full loading cycle and generation of the power spectral...
-
STEEL CONSTRUCTION - DESIGN AND RESEARCH
Czasopisma -
JOURNAL OF CONSTRUCTIONAL STEEL RESEARCH
Czasopisma -
The Effect of Fly Ash Microspheres on the Pore Structure of Concrete
PublikacjaThe fly ash microspheres (FAMs) formed during the mineral transformation stage in coal combustion are hollow spherical particles with a density less than water. This paper presents the results of X‐ray micro‐computed tomography and an automatic image analysis system of the porosity in the structure of hardened concrete with microspheres. Concrete mixtures with ordinary Portland cement and two substitution rates of cement by microspheres—5%...
-
Self-compacting grout to produce two-stage concrete
PublikacjaTraditional concrete (TC) is primarily composed of a mixture of cement, fine and coarse aggregates, and water. TC is made by mixing together all the components before placing them. Using non-traditional concrete (two-stage concrete) to solve and to eliminate the problem of the aggregate segregation which appears in TC and in the self-compacting concrete. Two-stage concrete (TSC) consists of two main components, namely the grout...
-
A concept of heterogeneous numerical model of concrete for GPR simulations
PublikacjaThe Ground Penetrating Radar (GPR) method, which is increasingly being used in the non-destructive diagnostics of reinforced concrete structures, often needs more accurate interpretation tools for analysis of experimental data. Recently, there has been growing interest in developing of various numerical models for exhaustive understanding of GPR data. This paper presents the concept of a heterogeneous numerical model of concrete,...
-
Verification of Selected Calculation Methods Regarding Shear Strength in Reinforced and Prestressed Concrete Beams
PublikacjaThe purpose of this article was an attempt to compare selected calculation methods regarding shear strength in reinforced and prestressed concrete beams. Several calculation methods were tested. This included codes: PN-EN 1992-1-1:2008 [1], ACI 318- 14 [2] and fib Model Code for Concrete Structures 2010 [3]. The analysis also consists of methods published in technical literature. Calculations of shear strengths were made based...
-
The resistance of S235JR steel to cavitation erosion
PublikacjaThe erosion resistance of S235JR steel to flow cavitation was investigated. In order to understand an influence of steel properties and cavitation intensities on the degradation mechanisms, low-carbon S235JR steel was tested in the as-received state and after thermal treatment (annealing) under four different flow velocities. Annealing decreased steel hardness, which made S235JR steel less resistant to cavitation erosion. The performed...
-
Application of gpr method in diagnostics of reinforced concrete structures
PublikacjaThis paper presents an application of the ground penetration method (GPR) for diagnostics of reinforced concrete structures. In situ measurements were conducted for three civil engineering structures: the ground floor structure, the abutment of the railway viaduct and the concrete well. The dual polarized ground penetrating radar with the antenna operating at a center frequency of 2 GHz was used for GPR surveys. Three different...
-
THE EFFECT OF NOTCH DEPTH ON CTOD VALUES IN FRACTURE TESTS OF STRUCTURAL STEEL ELEMENTS
PublikacjaIn elements of steel structures working at low temperatures, there is a risk of appearance of brittle fracture. This risk is reduced through the use of certified materials having guaranteed strength at a given temperature. A method which is most frequently used to determine brittle fracture toughness is the Charpy impact test, preformed for a given temperature. For offshore structures intended to work in the arctic climat e, the...
-
Comparison of low-temperature cracks intensity on pavements with high modulus asphalt concrete and conventional asphalt concrete bases
PublikacjaHigh modulus asphalt concrete (HMAC) base courses provide very good resistance to rutting and fatigue but they can increase the risk of low-temperature cracking as compared with conventional asphalt concrete (AC). The article presents the comparison of these two road materials in terms of low-temperature cracking. The statistical method based on the ordered logistic regression model was used. The analysis was based on results of...
-
Shear fracture of longitudinally reinforced concrete beams under bending using Digital Image Correlation and FE simulations with concrete micro-structure based on X-ray micro-computed tomography images
PublikacjaThe paper presents experimental and numerical investigations of the shear fracture in rectangular concrete beams longitudinally reinforced with steel or basalt bar under quasi-static three point bending. Shear fracture process zone formation and development on the surface of beams was investigated by Digital Image Correlation (DIC) whereas thorough analyses of 3D material micro-structure, air voids, width and curvature of shear...
-
The Impact Of The Selected Parameters Of Fdm Manufacturing Technology On Tribological Performance Of Abs–Steel Pair Under Dry Friction
PublikacjaThe paper presents the result of tribological test of ABS and steel samples sliding under dry friction. Polymeric samples were manufactured of ABS material using FDM technology. Testing was carried out in unidirectional sliding in a ring-on-flat contact in a PT-3 tribometer. The scope of tested parameters included volumetric and mass wear, the friction coefficient, and polymeric specimen temperature. Polymeric specimens used in...
-
EXPERIMENTAL AND NUMERICAL INVESTIGATIONS OF CONCRETE BEHAVIOUR AT MESO-LEVEL DURING QUASI-STATIC SPLITTING TENSION
PublikacjaThe paper describes experimental and numerical results of quasi-static splitting tensile tests on concrete specimens at meso-scale level. The loading strip was made of plywood or steel. Fracture in concrete was detected at the aggregate level by means of three non-destructive methods: 3D x-ray micro-computed tomography, 2D scanning electron microscope and manual 2D digital microscope. The discrete element method was used to directly...
-
Self-compacting grout to produce two-stage concrete
PublikacjaTraditional concrete (TC) is primarily composed...
-
Effect of slag coal ash and foamed glass on the mechanical properties of two-stage concrete
PublikacjaTwo-stage concrete (TSC) is known by various names such as colcrete, Polcrete, preplaced aggregate concrete and prepacked concrete. It is different from traditional concrete in two fundamental ways, namely method of construction and mix proportion. Two-stage concrete (TSC) is defined as firstly, coarse aggregates are placed into the formwork and grout is applied to fill in the between coarse aggregate particles voids. Secondly,...
-
Analysis of Transparent Concrete as an Innovative Material Used in Civil Engineering
PublikacjaSince the dawn of history concrete has been, right behind stone and brick, one of the oldest building materials. The ancient Romans took advantage of its opportunities. They constructed amazing architectural objects, which survived centuries as whole buildings or parts of them. Concrete is so ubiquitous, that when we are walking in a newer districts of cities we are virtually surrounded by concrete from everywhere. Sometimes...
-
CONCRETE MIX DESIGN USING ABRAMS AND BOLOMEY METHODS
PublikacjaOne way to reduce the consumption of cement is to optimize its use. Many known methods of concrete design, based on the Abrams law and the Bolomey method. Therefore, the authors chose those methods for analysis. The concrete composition with the assumed strength class, calculated by any method differs significantly. This applies especially to the cement content, as its content in the composition of concrete varies from 20 to 50%....
-
Adiabatic calorimetry results for fresh concrete mixes M0 and M100
Dane BadawczeAdiabatic calorimetry results for fresh 3D printed concrete mixes (M0 and M100) determined using Controls S.p.A., Italy calorimeter
-
Latest Achievements in Concrete Structures Three-Dimensional Printing
PublikacjaWe can hear about three-dimensional printed concrete structures for several years, up to date solutions in this technology allow entire printing settlements of tiny concrete houses. Due to technical limitations, these houses are still small and not very durable, but undoubtedly, this technology is developing. Home printed in three-dimensional technology can be an alternative to modular container buildings implemented in areas affected...
-
Investigating the effects of structural pounding on the seismic performance of adjacent RC and steel MRFs
PublikacjaAn insufficient separation distance between adjacent buildings is the main reason for structural pounding during severe earthquakes. The lateral load resistance system, fundamental natural period, mass, and stiffness are important factors having the influence on collisions between two adjacent structures. In this study, 3-, 5- and 9-story adjacent reinforced concrete and steel Moment Resisting Frames (MRFs) were considered to investigate...
-
Advanced Steel Construction
Czasopisma -
Iron and Steel Technology
Czasopisma -
STEEL RESEARCH INTERNATIONAL
Czasopisma -
The analysis of the influence of the corrosion protection method of selected steel elements on the steel structure life cycle costs
PublikacjaSteel products are widely used in the construction for the performance of essential and additional elements of engineering structures. They are characterized by high tensile strength, compression and bending, the structure homogeneity, the possibility of assembly regardless of the season and climatic conditions, ease of processing and the possibility of almost any shape. The main disadvantage of steel structures is their high susceptibility...
-
Partially prestressed concrete beams with bonded and unbonded strands
PublikacjaThis article relate the tests of partially prestressed concrete beams. There is presented the research programme - geometry of elements, method of loading, the materials and variables. There have been shown preliminary test results of prestressed concrete elements with bonded and unbonded strands, and compared to the test results of R.C. beam.
-
Application of wavelet transform in analysis of guided wave propagation signals for damage detection in a steel plate
PublikacjaThe paper presents results of experimental investigations on damage detection using guided wave propagation technique. The tested specimen was a steel plate with a defect in the form of a rectangular notch. Lamb waves were excited by a PZT actuator and sensed by a laser vibrometer. Since reflections from damage in registered signals are often masked by measurement noise, for identification of time of reflections from damage, continuous...
-
Determination of representative volume element in concrete under tensile deformation
PublikacjaW artykule podano sposoby określenia elementu reprezentatywnej objętości w betonie podczas rozciągania. Obliczenia wykonano przy zastosowaniu izotropowego modelu degradacji sztywności rozszerzonego o długość charakterystyczną mikrostruktury w ramach teorii nielokalnej. Zaproponowano 2 różne metody wyznaczania elementu reprezentatywnej objętości niezależnego od warunków brzegowych.
-
Model-Based Adaptive Machine Learning Approach in Concrete Mix Design
PublikacjaConcrete mix design is one of the most critical issues in concrete technology. This process aims to create a concrete mix which helps deliver concrete with desired features and quality. Contemporary requirements for concrete concern not only its structural properties, but also increasingly its production process and environmental friendliness, forcing concrete producers to use both chemically and technologically complex concrete...
-
REINFORCED CONCRETE SUPPORTING CONSTRUCTION OF THE STADIUM COVER FOR EURO 2012 IN GDAŃSK
PublikacjaIn the article structural issues that connected with the reinforced concrete supporting construction of the stadium roofing for EURO 2012 in Gdańsk were described. In the first part of the article the concept of stadium foundation were described. In the second the static - strength analysis for two variants fastening together individual foundation elements were made. The two assumed geometrically different concept of foundation...
-
Numerical Study of Concrete Mesostructure Effect on Lamb Wave Propagation
PublikacjaThe article presents the results of the numerical investigation of Lamb wave propagation in concrete plates while taking into account the complex concrete mesostructure. Several concrete models with randomly distributed aggregates were generated with the use of the Monte Carlo method. The influence of aggregate ratio and particle size on dispersion curves representing Lamb wave modes was analyzed. The results obtained for heterogeneous...
-
Analysis of load carrying capacity and destruction mechanism of an intermediate anchorage steel plate for pillar jib crane
PublikacjaPillar jib cranes are often mounted to existing floors with the use of an intermediate anchorage steel plate instead of using independent foundations, what is shown in the figure. Standards for steel design provide only basic rules for the design of such an intermediate plate. This study presents a simple design approach by using a numerical model in order to analyze different parameters that have significant influence in the anchorage...
-
3D X-ray Micro-CT Analysis of Rebar Corrosion in Reinforced Concrete Subjected to a Chloride-Induced Environment
PublikacjaThe paper presents experimental investigations of the concrete cover protective ability to coun-teract rebar corrosion in reinforced concrete cubes. To study and quantify the consequences of corrosion a reinforced concrete sample was subjected to chloride-induced environment in order to get corroded and combined with un-corroded sample. Chloride-accelerated technique can in-duce a high degree of corrosion within at a controlled...
-
Monitoring of concrete curing in extradosed bridge supported by numerical simulation
PublikacjaThe paper describes a mathematical model of concrete curing taking into account kinetics of setting reactions. The numerical model is implemented in the author’s program that was used to monitor thermal effects recorded in the concrete bottom plate of the extradosed bridge. Numerical approach was verified by experimental measurements and used for assessment of the current compressive strength due to degree of hydration of fresh...
-
Column base fixity in steel moment frames: Observations from instrumented buildings
PublikacjaThe rotational fixity of column base connections in Steel Moment Resisting Frames (SMRFs) strongly influences their seismic response. However, approaches for estimating base fixity have been validated only against laboratory test data. These approaches are examined based on strong motion recordings from four instrumented SMRF buildings in California to informbest practices for seismic response simulation. These buildings represent...
-
Concrete Compressive Strength Under Changing Environmental Conditions During Placement Processes
PublikacjaThe technological process of concrete production consists of several parts, including concrete mix design, concrete mix production, transportation of fresh concrete mix to a construction site, placement in concrete framework, and curing. Proper execution of these steps provides good quality concrete. Some factors can disturb the technological process, mainly temperature and excessive precipitation. Changing daily temperature and...
-
Recent steel structures in Poland - the selected projects
PublikacjaThe paper presents selected examples of recently completed steel structures in Poland. These are roofs over sport stadiums, construction of public buildings and bridges. Described examples do not exhaust the acquis in the field of steel constructions in Poland. The authors, however, may hope that the presented con-structions represents current achievements in Poland in the field of steel structures.
-
Behaviour of steel columns under impact
PublikacjaOne of import issues related to the idea of sustainable society is the safety of civil engineering structures. The safety and reliability of steel structures under impact loading is among a number of different aims during the design state. The aim of this paper is to present the results of investigation focused on dynamic behaviour of steel columns under impact loading. Modal and transient dynamic analyses using Finite Element...
-
The influence of reinforcement on load carrying capacity and cracking of the reinforced concrete deep beam joint
PublikacjaThe paper presents the results of experimental research of the spatial reinforced concrete deep beam systems orthogonally reinforced and with additional inclined bars. Joint of the deep beams in this research was composed of the longitudinal deep beam with a cantilever suspended at the transversal deep beam. The cantilever deep beam was loaded throughout the depth and the transversal deep beam was loaded at the mid-span by longitudinal...
-
A novel heterogeneous model of concrete for numerical modelling of ground penetrating radar
PublikacjaThe ground penetrating radar (GPR) method has increasingly been applied in the non-destructive testing of reinforced concrete structures. The most common approach to the modelling of radar waves is to consider concrete as a homogeneous material. This paper proposes a novel, heterogeneous, numerical model of concrete for exhaustive interpretation of GPR data. An algorithm for determining the substitute values of the material constants...
-
Experimental Study of the Resistance to Influence of Aggressive Liquids on Lightweight Concrete
PublikacjaIn light of the scientific research, the corrosion of concrete structures is one of the main problems that may reduce their durability due to the negative impact of the natural environment. The paper analyzes the influence of the type of component on the selected properties of lightweight concrete subjected to the influence of aggressive liquids. Four concrete mixes were prepared with a granular aggregate made of foamed glass (GEGA)...
-
The effect of macro polymer fibres length and content on the fibre reinforced concrete
PublikacjaThe paper presents studies of a ready-mix concrete containing polymer fibres of three different lengths: 24, 38 and 54 mm. The performed tests allowed to determine the effect of fibre volume fraction and length on the concrete strength. The basic parameters of concrete mixture (consistency, air content and bulk density) were identified. Fibre reinforced concrete belongs to a group of composite materials. The polymer fibres are...