Filtry
wszystkich: 3341
wybranych: 3158
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: HAEMOPHILUS INFLUENZAE
-
Influence of meniscus shape in the cross sectional plane on the knee contact mechanics
PublikacjaWe present a three dimensional finite element analysis of stress distribution and menisci deformation in the human knee joint. The study is based on the Open Knee model with the geometry of the lateral meniscus which shows some degenerative disorders. The nonlinear analysis of the knee joint under compressive axial load is performed. We present results for intact knee, knee with partial and complete radial posterior meniscus root...
-
INFLUENCE OF NANOPARTICLE CONCENTRATION ON THERMAL PROPERTIES OF THERMAL OIL-MWCNT NANOFLUID
PublikacjaThis paper deals with measurements of dynamic viscosity, thermal conductivity, electrical conductivity and pH of thermal oil-MWCNT (TO-MWCNT) nanofluid. Nanoparticles were tested at the concentration of 0.001%, 0.005%, 0.01%, 0.05%, and 0,1% by weight. Ultrasonic vibration was used in order to stabilize the dispersion of the nanoparticles. Thermal oil (TO) was selected as a base liquid, because of possible application in ORC systems...
-
INFLUENCE OF TEST CONDITIONS ON TYRE/ROAD NOISE MEASURED BY THE DRUM METHOD
PublikacjaTyre/road noise is one of the most important environmental problems related to road traffic. Nowadays a few standard procedures of tyre/road noise measurements are in use. Unfortunately, measurement conditions specified within relevant standards are very different. For example, procedure described in ISO 11819-2 used for pavement investigations requires tyre load of 3200 N and capped inflation pressure of 200 kPa. At the same time...
-
Investigation of influence of space mopdes interaction on nonlinear dynamics of sound beams
PublikacjaOperatory rzutu na mody są zdefiniowane w dynamice płynów trójwymiarowych. Zostały wyprowadzone równania ewolucyjne. Rezultaty obliczeń numerycznych przedstawione.
-
Influence of zinc and magnesium carboxylates on properties of emulsions stabilized with acylglycerol emulsifiers.
PublikacjaOkreślono właściwości emulsji stabilizowanych emulgatorami acyloglicerolowymi modyfikowanymi karboksylanami cynku i magnezu. Zbadano wpływ kompozycji emulgatorów na HLB i efektywność w modelowych układach emulsyjnych.
-
Influence of surfactants on interaction forces between polyethylene surfaces in a hydrocarbon solvent.
PublikacjaPrzeprowadzono bezpośrednie pomiary oddziaływań międzyfazowych pomiędzy cząstkami polietylenowymi w środowisku n-tetradekanu z dodatkiem surfaktantów(kwasu larynowego i dodecyloaminy). Dodatek surfaktantów wpłynął na wzrost oddziaływań odpychających pomiędzy powierzchniami polietylenowymi, szczególnie w przypadku dodecyloaminy. Zaobserwowano obecność wzrostu sferycznych sił odpychających ze wzrostem temperatury.
-
A Molecular dynamics study of the influence of chemical reduction on the structure of amorphous germania
PublikacjaPraca poświęcona jest badaniom struktury blisko- i średniozasięgowej redukowanego amorficznego tlenku germanu o składzie 1Ge 1GeO2 za pomocą symulacji dynamiczno-molekularnych. Symulacje MD realizowano w zespole mikrokanonicznym (NVE), z wykorzystaniem dwuciałowego potencjału oddziaływania miedzyatomowego Borna-Mayera-Hugginsa. Wyraźnie widoczna tendencja do aglomeracji neutralnych atomów Ge została porównana z tendencją do aglomeracji...
-
Influence of annealing on joint zone of explosive welded and rolled Al-Cuplate
PublikacjaRosnące wciąż wymagania co do metalowych materiałów jednorodnych przyczyniło się do zwiększenia zainteresowania materiałami platerowanymi. Blachy platerowane często znajdują zastosowanie w przemyśle chemicznym i petrochemicznym jako materiały antykorozyjne odporne na działanie agresywnego środowiska, w przemyśle okrętowym jako łączniki stopów aluminium ze stalą, w budowie zgrzewarek jako połączenia szczęk z blachą stalową, w przemyśle...
-
The influence of splicing misalignment on the performance of polarimetricsensors. Optoelectronic and Electronic Sensors V.
PublikacjaW pracy badano wpływ błędu orientacji kątowej segmentów toru światłowodowych sensorów polarymetrycznych na widzialność interferujących modów polaryzacji.Przy pomocy formalizmu macierzowego Jonesa analizowano dwie klasy sensorów z pojedynczą i z podwójną kompensacją temperatury.
-
Influence of microstructure on properties of 18Cr-10Ni-Ti stainless steel products.
PublikacjaBadano wpływ mikrostruktury na właściwości mechaniczne i odporność korozyjną wyrobów ze stali austenitycznej 18Cr-10Ni-Ti po przesycaniu z temperatury 1050 C. Wykazano, że węgliki TiC w ziarnach i na granicach ziaren/bliźniaków powodują znaczne obniżenie wydłużenia stali. Węgliki TiC na granicach ziaren/bliźniaków obniżają odporność na korozję międzykrystaliczną i sprzyjają powstawaniu uszkodzeń korozyjnych podczas hutniczej operacji...
-
Influence of deformation velocity on mechanical properties of high strength structural steels.
PublikacjaW referacie przedstawiono wyniki badań własności mechanicznych stali wysokiej wytrzymałości przeznaczonych na spawane konstrukcje okrętowe w zależności od prędkości odkształcenia. Badania były prowadzone w Akademii Marynarki Wojennej oraz w Politechnice Gdańskiej przy współudziale Uniwersytetu Technicznego w Rostocku podczas opracowywania charakterystyk tych stali dla potrzeb polskiego przemysłu okrętowego. Uwzględnienie obciążeń...
-
The influence of sampling parameters on accuracy of capacitance measurement in the method based on DSP.
PublikacjaW artykule przedstawiono metodę pomiaru parametrów impedancyjnych bazującą na próbkowaniu sygnałów pomiarowych i DSP. Przeanalizowano wpływ głównych źródeł niepewności i błędów na dokładność pomiaru pojemności. Zawarto analizę dla następujących parametrów: niesynchroniczne próbkowanie sygnałów pomiarowych (napięciowego i prądowego), rozdzielczość przetwornika a/c i ilość zbieranych próbek. Załączono wyniki symulacji.
-
Influence of heat transformations on microstructure and properties of some wrought aluminium alloys.
PublikacjaOmówiono wpływ spawania na podatność do korozji naprężeniowej stopów Al-Mg i Al-Zn-Mg stwierdzając, że wzrost zawartości cynku wywołuje wzrost właściwości mechanicznych i spadek odporności na korozję naprężeniową. Wykazano, że obróbka cieplna złożona z retrogresji i powtórnego starzenia w przypadku stopów Al-Zn-Mg nie powoduje szczególnych zmian odporności na korozję naprężeniową, co pozostaje w związku z niewielką zmianą struktur...
-
Influence of polyaniline primer on the corrosion properties of St3S steel - coating system
PublikacjaPraca przedstawia wyniki badań wpływu podkładu z polianiliny osadzonej elektrochemicznie na właściwości antykorozyjne powłoki epoksydowej na stali niskowęglowej St3S. Wykonano badania próbek nieuszkodzonych, a także próbek ze sztucznym defektem powłoki. Próbki były eksponowane na środowisko korozyjne przez 63 dni i były sukcesywnie badane za pomocą elektrochemicznej spektroskopii impedancyjnej. Postępy korozji były również oceniane...
-
The influence of the welding thermal cycles on corrosion resistance of duplex stainless steel
PublikacjaBadano skłonnośc strefy wpływu ciepła spoin ze stali dupleks do korozyjnego pękania narężeniowego. Wykonano próby korozyjne z wykorzystaniem metody SSRT w środowisku korozyjnym wrzącego MgCl2. Wykazano, że duży udział ferrytu w strukturze SWC pogarsza odpornośc na korozję. Badania metalograficzne na mikroskopie lektronowym wykazały różne sposoby propagacji pęknięcia zależnie od zawartości austenitu w strukturze SWC.
-
Simulation of influence of the air gap asymmetryon voltage waveforms of a synchronous machine
PublikacjaResults of simulation of a synchronous generator with the air gap asymmetry characterised by eccentricity are presented in the paper. The Lagrange's energy method has been used in derivation of the model equations. Analysis of influence of the air gap asymmetry on characteristics of self and mutual inductances of windings, as well as analysis of induced voltage waveforms as a function of the air gap asymmetry have been performed....
-
Recommendations for the prevention, diagnosis and treatment of inFLUenza in adults for Primary care physiciAnS: FLU COMPAS PCP – ADULTS
Publikacja -
Impact of European vaccination policies on seasonal influenza vaccination coverage rates: An update seven years later
Publikacja -
Motors of influenza vaccination uptake and vaccination advocacy in healthcare workers: A comparative study in six European countries
Publikacja -
A rapid-response ultrasensitive biosensor for influenza virus detection using antibody modified boron-doped diamond
PublikacjaAccording to the World Health Organization (WHO), almost 2 billion people each year are infected worldwide with flu-like pathogens including influenza. This is a contagious disease caused by viruses belonging to the family Orthomyxoviridae. Employee absenteeism caused by flu infection costs hundreds of millions of dollars every year. To successfully treat influenza virus infections, detection of the virus during the initial development...
-
INFLUENCE OF THE HULL SHAPE ON THE ENERGY DEMAND OF A SMALL INLAND VESSEL WITH HYBRID PROPULSION
PublikacjaRecently, there has been a significant development of ecological propulsion systems, which is in line with the general trend of environmentally friendly “green shipping”. The main aim is to build a safe, low-energy passenger ship with a highly efficient, emission-free propulsion system. This can be achieved in a variety of ways. The article presents the main problems encountered by designers and constructors already at the stage...
-
Assessment of User Mobility’s Influence on System Loss in Several Body-to-Body Scenarios
PublikacjaIn this paper, Body-to-Body communications in indoor and outdoor environments for different on-body antenna configurations and different mobility scenarios were studied, based on system loss measurements at 2.45 GHz. The main objective is to properly characterise the influence of the Transmitter-Receiver configuration on system loss and fast fading behaviour, the latter being modelled by the Rice Distribution. Globally, it is observed...
-
Influence of the fragment size on the recycling process of thin-film modules based on CdTe
PublikacjaFor several years, the production of second generation cells (the so-called thin film), produced from amorphous silicon, cadmium telluride (CdTe) or copper indium (gallium) diselenide (CI(G)S), has been increasing. The total number of end-of-life panels by 2050 is expected to reach 9.57 million tonnes. They contain heavy metals that can be leached into the environment at the land field. The EU directive on waste electrical and...
-
Influence of Operation Conditions on Temperature Hazard of Lithium-Iron-Phosphate (LiFePO4) Cells
PublikacjaThe article presents and discusses the results of research on hazard, especially temperature, for selected lithium-ion-phosphate cells operated in accordance with the manufacturer’s recommendations but used under onerous mining conditions. This applies to the performance of cells in battery sets without the application of any management system (BMS). On the basis of the obtained test results, first of all, the influence of the...
-
Influence of Annealing Atmospheres on Photoelectrochemical Activity of TiO2 Nanotubes Modified with AuCu Nanoparticles
PublikacjaIn this article, we studied the annealing process of AuCu layers deposited on TiO2 nanotubes (NTs) conducted in various atmospheres such as air, vacuum, argon, and hydrogen in order to obtain materials active in both visible and UV–vis ranges. The material fabrication route covers the electrochemical anodization of a Ti plate, followed by thin AuCu film magnetron sputtering and further thermal treatment. Scanning electron microscopy...
-
Influence of the Shear Cap Size and Stiffness on the Distribution of Shear Forces in Flat Slabs
PublikacjaThe scope of this paper is to investigate analytically and numerically the influence of shear cap size and stiffness on the distribution of shear forces in flat slabs in a slab–column-connections-reinforced concrete structure. The effect of support (shear cap) stiffness on the calculation of the length of the shear control perimeter according to the available methods is presented. Based on the analysis, the authors indicate in...
-
Influence of Laser Modification on the Surface Character of Biomaterials: Titanium and Its Alloys—A Review
PublikacjaLaser surface modification is a widely available and simple technique that can be applied to different types of materials. It has been shown that by using a laser heat source, reproducible surfaces can be obtained, which is particularly important when developing materials for medical applications. The laser modification of titanium and its alloys is advantageous due to the possibility of controlling selected parameters and properties...
-
Influence of Surface Modification of Titanium and Its Alloys for Medical Implants on Their Corrosion Behavior
PublikacjaTitanium and its alloys are often used for long-term implants after their surface treatment. Such surface modification is usually performed to improve biological properties but seldom to increase corrosion resistance. This paper presents research results performed on such metallic materials modified by a variety of techniques: direct voltage anodic oxidation in the presence of fluorides, micro-arc oxidation (MAO), pulse laser treatment,...
-
Influence of hydrogen on a nanocrystalline high-entropy oxide with application potential in hydrogen technologies
PublikacjaThe influence of hydrogen on a (Co0⋅2Cu0⋅2Mg0⋅2Ni0⋅2Zn0.2)O HEO with a rock salt structure was studied. Two forms of this HEO (nanopowder and sinter) were prepared via mechanochemical synthesis (MS) and additional heat treatment, respectively. The chemical stability of the synthesized samples in a pure hydrogen atmosphere was investigated using Sievert’s technique. High-pressure hydrogenation at 250 ◦C had no noticeable effect...
-
Influence of Surface-Modified Montmorillonite Clays on the Properties of Elastomeric Thin Layer Nanocomposites
PublikacjaIn recent years, polyurethane nanocomposites have attracted more attention due to the massive demand for materials with increasingly exceptional mechanical, optical, electrical, and thermal properties. As nanofillers have a high surface area, the interaction between the nanofiller and the polymer matrix is an essential issue for these materials. The main aim of this study is to validate the impact of the montmorillonite nanofiller...
-
Influence of Different Nanometals Implemented in PMMA Bone Cement on Biological and Mechanical Properties
PublikacjaCemented arthroplasty is a common process to fix prostheses when a patient becomes older and his/her bone quality deteriorates. The applied cements are biocompatible, can transfer loads, and dampen vibrations, but do not provide antibacterial protection. The present work is aimed at the development of cement with antibacterial effectivity achieved with the implementation of nanoparticles of different metals. The powders of Ag,...
-
In-Reactor Polypropylene Functionalization─The Influence of Catalyst Structures and Reaction Conditions on the Catalytic Performance
PublikacjaTo unravel the relationship between silylene-bridged metallocene catalyst structures and polymerization conditions and their effect on the performance in in-reactor functionalization of polypropylene, the behaviors of rac-Me2Si(2-Me-4-Ph-Ind)2ZrCl2/MMAO, rac-Me2Si(Ind)2ZrCl2, rac-Me2Si(2-Me-4-Ph-Ind)2HfCl2, and rac-Me2Si(Ind)2HfCl2 in propylene/aluminum alkyl-passivated 10-undecen-1-ol copolymerization were compared. Kinetic analysis...
-
Influence of Properties of Hydraulic Fluid on Pressure Peaks in Axial Piston Pumps’ Chambers
PublikacjaThe article concentrates on the research of the pressure peaks in a working chamber of an axial piston pump. The main focus of the article is the influence of fluid properties on the pressure peaks value. Experimental and analytical methods were used to determine the impact of the fluid density, viscosity, compressibility and aeration. The article describes the pressure peak generation process and explains the theoretical basis...
-
Influence of excitons interaction with charge carriers on photovoltaic parameters in organic solar cells
PublikacjaWe report on theoretical analysis of excitons annihilation on charge carriers in organic solar cells. Numerical calculations based on transient one-dimensional drift-diffusion model have been carried out. An impact of three quantities (an annihilation rate constant, an exciton mobility and a recombination reduction factor) on current density and concentrations of charge carriers and excitons is investigated. Finally, we discuss...
-
The influence of the substrate temperature on the preparation of DNA films for studies under vacuum conditions
PublikacjaExperiments were carried out to determine the dependence of the physical form of supercoiled DNA films on the initial temperature of the substrate. Such films are often used in irradiation experiments involving low energy particles, like electrons or photons. In order to obtain absolute values for cross sections for such experiments, the spatial distribution of the sample in the film has to be well estimated. These investigations...
-
Influence of bitumen type on cracking resistance of asphalt mixtures used in pavement overlays
PublikacjaCracking is one of the predominant distresses occurring in flexible pavements, especially in old pavements that were rehabilitated with an asphalt overlay. In such cases asphalt mixtures should be designed to ensure high resistance to reflective cracking because new asphalt layers are exposed to existing cracks of the old pavement. The nature of these cracks can be various (transverse, longitudinal as well as crazy cracking). One...
-
The influence of the development of private air communication on the architecture and urban planning of the 21st century
PublikacjaIn the first part, the article describes the stages of the development of gyroplanes and the influence of wartime policy on the interest in light aircraft. Also presented are links and the possibilities of using gyroplanes in various sectors of the economy. The authors, based on source texts, present the current position of the aviation industry in the Polish economy and attempt to diagnose its development capabilities. As a result,...
-
The influence of inflation pressure and ambient temperature on the value of the truck tires rolling resistance
PublikacjaThe articlediscusses the effect of inflation pressure and the ambient temperature on the value of the rolling resistance of truck tires which directly translates into fuel consumption. For this purpose, a series of measurements was made at two ambient temperatures (at 25°C and -15°C), using different pumping pressures.
-
PARAMETERS OF THE ELECTROPHORETIC DEPOSITION PROCESS AND ITS INFLUENCE ON THE MORPHOLOGY OF HYDROXYAPATITE COATINGS. REVIEW
PublikacjaMetallic materials intended for bone implants should exhibit not only appropriate mechanical properties, but also high biocompatibility. The surface treatment modifications, for example acidic treatment, laser treatment, ion implantation and deposition of highly biocompatible coatings, are practiced. One of the most popular methods of surface modification is to deposit hydroxyapatite (HAp) coatings. HAp naturally occurs in human...
-
Geometry optimization of steroid sulfatase inhibitors - the influence on the free binding energy with STS
PublikacjaIn the paper we review the application of two techniques (molecular mechanics and quantum mechanics) to study the influence of geometry optimization of the steroid sulfatase inhibitors on the values of descriptors coded their chemical structure and their free binding energy with the STS protein. We selected 22 STS-inhibitors and compared their structures optimized with MM+, PM7 and DFT B3LYP/6–31++G* approaches considering separately...
-
Influence of the analyzing window on electrode impedance measurement by the continuous frequency scanning method
Publikacja -
Influence of Bitumen Type and Asphalt Mixture Composition on Low-temperature Strength Properties
Publikacja -
Influence of W Addition on Microstructure and Mechanical Properties of Al-12%Si Alloys
Publikacja -
Research of Influence Electric Conditions Combined ElectroDiamond Processing by on Specific Consumption of Wheel*
Publikacja -
Influence of modification by superdispersed powder of aluminum oxide on lead-tin bronze structure
Publikacja -
Influence of dissolved organic matter in natural and simulated water on the photochemical decomposition of butylparaben
Publikacja -
Influence of potato variety on polyphenol profile composition and glycoalcaloid contents of potato juice
Publikacja -
The influence of of cross-linking process on the physicochemical properties of new copolyesters containing xylitol
Publikacja -
The Influence of Selected Plant Essential Oils on Morphological and Physiological Characteristics in Pseudomonas Orientalis
Publikacja -
The influence of the shift work system on dietary factors contributing to the development of cardiovascular diseases
Publikacja