Filtry
wszystkich: 1103
wybranych: 954
Wyniki wyszukiwania dla: vaccination coverage
-
Nitrogen mass balance and mathematical model of a Structured- Bed Reactor (SBRRIA)
PublikacjaAn up-flow structured-bed reactor subjected to recirculation and intermittent aeration (SBRRIA) was operated under varying influent conditions. The influent COD/N ratio was adjusted by maintaining a stable organic loading rate (average of 1.07 kgCOD m-3 d-1) and changing the nitrogen loading rate from 0.1 to 0.4 kg N m-3. Therefore, three different COD/N ratios were tested: 9.7±1 (Scenario 1); 7.6±1 (Scenario 2) and 2.9±1 (Scenario...
-
Impact of Climate Change on Groundwater Resources in a Young Glacial Multi-Aquifer System
PublikacjaThe aim of this study was to evaluate the trends of climate change on the Kashubian Lake District and to determine the impact of expected trends on groundwater resources. The analysis of trends in temperature and precipitation was conducted for the six-decade history of meteorological measurements at the weather station in Koscierzyna. The analysis shows the trend of temperature increase of +0.0182ºC/year. The highest increase...
-
Towards Contactless, Hand Gestures-Based Control of Devices
PublikacjaGesture-based intuitive interactions with electronic devices can be an important part of smart home systems. In this paper, we adapt the contactless linear gesture sensor for the navigation of smart lighting system. Set of handled gestures allow to propose two methods of active light source selection, continuous dimming, and turning on and off based on discrete gestures. The average gesture recognition accuracy was 97.58% in the...
-
A Geometrically Simple Compact Wideband Circularly Polarized Antenna
PublikacjaA compact broadband wide-slot circular polarization (CP) antenna is proposed. An inverted L-shape parasitic strip at the open end of a microstrip line extension and a slot modification is applied to attain wideband CP. The advantage of this technique is simplicity which makes it readily re-designable for different frequency bands. To demonstrate the concept, three designs working at different frequencies are obtained. The redesign...
-
The efficiency and technological reliability of biogenic compounds removal during long-term operation of a one-stage subsurface horizontal flow constructed wetland
PublikacjaThe paper presents the results of a study of the efficiency and technological reliability of total nitrogen and total phosphorus removal during long term operation of a one-stage constructed wetland system with subsurface horizontal wastewater flow. The flow rate of the wastewater treatment plant was 1.2m3/d during the research period. Physical and chemical analyses of raw wastewater and treated effluent were carried out in the...
-
A Broadband Circularly Polarized Wide-Slot Antenna with a Miniaturized Footprint
PublikacjaThis letter presents a novel and simple feeding technique for exciting orthogonal components in a wide-slot antenna. In this technique, a rectangular bracket-shape parasitic strip is placed at the open end of the straight microstrip line to excite the fundamental horizontal and vertical components of the circular polarization (CP). The proposed technique—when employed in conjunction with the asymmetrical geometry of coplanar waveguide...
-
Methods of trend removal in electrochemical noise data – overview
PublikacjaIn this paper we shall review popular methods of trend removal from electrochemical noise time records. The basic principles of operation of the six most popular methods are explained. The proposed methods are: high - pass filtering, Moving Average Removal, polynomial detrending, wavelet detrending, Empirical Mode Decomposition and Variational Mode Decomposition. Estimation of trend removal quality...
-
A novel dual-band rectifier circuit with enhanced bandwidth for RF energy harvesting applications
PublikacjaIn recent years, a rapid development of low-power sensor networks, enabling machine-to-machine communication in applications such as environmental monitoring, has been observed. Contemporary sensors are normally supplied by an external power source, typically in a form of a battery, which limits their lifespan and increases the maintenance costs. This problem can be addressed by harvesting and converting ambient RF energy into...
-
Methylmercury and total mercury content in soft tissues of two bird species wintering in the Baltic Sea near Gdansk, Poland
PublikacjaOf the various forms of Hg occurring in nature, (mono) methylmercury (MeHg) is an especially toxic form and practically all forms of Hg can be converted into MeHg as a result of natural processes. Total mercury (THg) and MeHg were determined in tissues of two piscivorous birds: razorbill Alca torda and black-throated loon Gavia arctica to provide baseline data on current mercury concentrations for liver, kidneys and pectoral muscle...
-
Clothes Detection and Classification Using Convolutional Neural Networks
PublikacjaIn this paper we describe development of a computer vision system for accurate detection and classification of clothes for e-commerce images. We present a set of experiments on well established architectures of convolutional neural networks, including Residual networks, SqueezeNet and Single Shot MultiBox Detector (SSD). The clothes detection network was trained and tested on DeepFashion dataset, which contains box annotations...
-
The application of moving bed biofilm reactor to denitrification process after trickling filters
PublikacjaThe paper presents research of a prototype moving bed biofilm reactor (MBBR). The device was used for the post-denitrification process and was installed at the end of a technological system consisting of a septic tank and two trickling filters. The concentrations of suspended biomass and biomass attached on the EvU Perl moving bed surface were determined. The impact of the external organic carbon concentration on the denitrification...
-
ANALYSIS OF POSSIBILITIES FOR THE USE OF VOLUME-DELAY FUNCTIONS IN THE PLANNING MODULE OF THE TRISTAR SYSTEM
PublikacjaTravel time is a measure commonly used for traffic flow modelling and traffic control. It also helps to evaluate the quality of traffic control systems in urban areas. Traffic control systems that use traffic models to predict changes and disruptions in vehicle flows have to use vehicle speed-prediction models. Travel time estimation studies the effects of traffic volumes on a street section at an average speed. The TRISTAR Integrated...
-
An investigation of selected monoaromatic hydrocarbons released from the surface of polystyrene lids used in coffee-to-go cups
PublikacjaA consumer trend towards the fast preparation of beverages has increased the popularity of hot beverages (especially coffee and tea) available in disposable containers called coffee-to-go cups with fitted polystyrene lids. Lids in contact with hot beverages may release low molecular weight organic compounds into the gaseous phase causing direct exposure of consumers to these compounds during drinking. The paper describes in detail...
-
Accurate Lightweight Calibration Methods for Mobile Low-Cost Particulate Matter Sensors
PublikacjaMonitoring air pollution is a critical step towards improving public health, particularly when it comes to identifying the primary air pollutants that can have an impact on human health. Among these pollutants, particulate matter (PM) with a diameter of up to 2.5 μ m (or PM2.5) is of particular concern, making it important to continuously and accurately monitor pollution related to PM. The emergence of mobile low-cost PM sensors...
-
Physicochemical and Volatile Compounds Analysis of Fruit Wines Fermented with Saccharomyces cerevisiae: FTIR and Microscopy Study with Focus on Anti-Inflammatory Potential
PublikacjaThe growing trend in fruit wine production reflects consumers’ interest in novel, diverse drinking experiences and the increasing demand for healthier beverage options. Fruit wines made from kiwi, pomegranates, and persimmons fermented using S. bayanus Lalvin strain EC1118 demonstrate the versatility of winemaking techniques. Kiwifruit, persimmon, and pomegranate wines were analyzed using HPLC and GC-TOFMS analyses to determine...
-
SZACOWANIE ZAWARTOŚCI BENZO(a)PIRENU W PYLE ZAWIESZONYM PM10 W AGLOMERACJI TRÓJMIEJSKIEJ ZA POMOCĄ WIELOWYMIAROWEJ REGRESJI LINIOWEJ=ESTIMATION OF BENZO(A)PYRENE CONTENT IN SUSPENDED DUST PM10 IN TRI-CITY AGGLOMERATION USING MULTIDIMENSIONAL LINEAR REGRESSION
PublikacjaW pracy przedstawiono próbę oszacowania przy pomocy wielowymiarowej regresji liniowej modelu empirycznego opisującego czynniki wpływające na zawartość B(a)P w pyle zawieszonym PM10 w Aglomeracji Trójmiejskiej w latach 2008-2011. Na przestrzeni tych lat średnioroczne stężenie B(a)P w PM10 wzrosło ponad dwukrotnie i ponad trzykrotnie przewyższa poziom docelowy. Z przeprowadzonych analiz wynika, że główną przyczyną wzrostu stężenia...
-
Inwestycje w surowce w połączeniu z polskim rynkiem kapitałowym, analiza ryzyka i efektywności
PublikacjaW artykule przedstawiono główne kategorie i rodzaje inwestycji w surowce. Cel opracowania to zbadanie czy inwestycja w Warszawski Indeks Giełdowy stanowi główny składnik optymalnego tj. cechującego się minimalnym ryzykiem portfela inwestycyjnego. Ponadto ustalono czy wspomniana inwestycja tradycyjna stanowi najważniejszy element portfela inwestycyjnego odznaczającego się najwyższą efektywnością. Stwierdzono, że wszystkie z 29 analizowanych...
-
Zagadnienia tribologiczne w hamulcu silnika hydraulicznego
PublikacjaPrzedmiotem badań był prototypowy hamulec cierny wielopłytkowy do silnika satelitowego SM-0,6 o teoretycznej objętości roboczej 16,7 cm3/obr. Hamulec ten zbudowany był z 27 tarcz ciernych wykonanych z materiału TOLOX oraz z pakietu sprężyn talerzowych zamontowanych w układzie X. Zablokowanie hamulca następuje w skutek siły docisku pakietu sprężyn talerzowych płytek ciernych co następuje w chwili spadku ciśnienia w komorze tłoka...
-
"Raport z wstępnych badań własności stali trudnościeralnej 460HB",. ang "Report on preliminary tests of the properties of wear-resistant steel 460HB"
PublikacjaMikrostrukturę badanej stali trudnościeralnej 460HB stanowi drobnoziarnisty martenzyt odpuszczony, który jest właściwy dla stali konstrukcyjnych niskowęglowych, niskostopowych ulepszonych cieplnie. W przypadku blach grubych, do których zalicza się badana stal, struktura może ulec zaburzeniu, jeżeli w hutniczym procesie wytwórczym wystąpiła niejednorodność odkształcenia plastycznego i w konsekwencji tworzenie się pasm segregacyjnych,...
-
Study on the Coastline Evolution in Sopot (2008–2018) Based on Landsat Satellite Imagery
PublikacjaThe coastline is the boundary between the water surface in a reservoir or watercourse and the land, which is characterised by high instability and functional diversity. For these reasons, research on coastal monitoring has been conducted for several decades. Currently, satellite images performed with synthetic aperture radars (SARs) are used to determine its course and variability together with high-resolution multispectral imagery...
-
Medical Image Dataset Annotation Service (MIDAS)
PublikacjaMIDAS (Medical Image Dataset Annotation Service) is a custom-tailored tool for creating and managing datasets either for deep learning, as well as machine learning or any form of statistical research. The aim of the project is to provide one-fit-all platform for creating medical image datasets that could easily blend in hospital's workflow. In our work, we focus on the importance of medical data anonimization, discussing the...
-
Recycling of Photovoltaic Solar Cells and Modules - Te State - Of - Art
PublikacjaIn comparison to other energy producing techniques, photovoltaics (PV) is one of the most promising options: no emission of any matter into the environment during operation; extremely long operation period (estimated average: 25 years), minimum maintenance, robust technique, aesthetic aspects. The use of photovoltaics is rapidly increasing, and the respective market is developing accordingly. Although PV manufacturing equipment...
-
Visible light activity of rare earth metal doped (Er3+, Yb3+ or Er3+/Yb3+) titania photocatalysts
PublikacjaA series of Er3+-TiO2, Yb3+-TiO2 and Er3+/Yb3+-TiO2 photocatalysts were obtained via sol-gel method, using rare earth metal (RE) precursor ranging from 0.25 to 10 mol%. The experiments demonstrated that phenol in aqueous solutions was successfully degraded under visible light (> 450 nm) using RE3+-TiO2. The as-prepared samples were characterized by X-ray diffraction (XRD), X-ray photoelectron emission spectroscopy (XPS), UV-Vis...
-
CURRENT TRENDS IN RECYCLING OF PHOTOVOLTAIC SOLAR CELLS AND MODULES WASTE
PublikacjaIn comparison to other energy producing techniques, photovoltaics (PV) is one of the most promising options: no emission of any matter into the environment during operation; extremely long operation period (estimated average: 25 years), minimum maintenance, robust technique, aesthetic aspects. The use of photovoltaics is rapidly increasing, and the respective market is developing accordingly. Although PV manufacturing equipment...
-
Temperature influence on tyre/road noise of selected tyres
PublikacjaAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
The best porous asphalt pavement in Sweden so far
PublikacjaIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed in various versions on the E4 motorway through the Swedish city Huskvarna. As a result of a court decision the Swedish Transport Administration had to reduce noise emission by applying a low noise road surface that would reduce A-weighted noise levels by 5 dB, as an average. Earlier experience in Sweden indicated that it was possible to obtain a high...
-
Maturity Mismatch in the Polish Banking System and its Impact on the Economy
PublikacjaIn the article maturity mismatch in the Polish banking system is estimated based on the publicly available data. Then the impact on the economy is discussed. Based on Polish central bank’s data it may be estimated that between 1996 and 2012 the maturity gap increased significantly – average residual maturity of assets exceeds 6 years in 2012 (less than 2 years in 1996), while that of liabilities remains below 1 year. The gap...
-
Globalized parametric optimization of microwave components by means of response features and inverse metamodels
PublikacjaSimulation-based optimization of geometry parameters is an inherent and important stage of microwave design process. To ensure reliability, the optimization process is normally carried out using full-wave electromagnetic (EM) simulation tools, which entails significant computational overhead. This becomes a serious bottleneck especially if global search is required (e.g., design of miniaturized structures, dimension scaling over...
-
Numerical investigation on dynamic response of a steel lattice tower under various seismic events
PublikacjaThe present paper presents the results of the numerical study designed to investigate the soil-structure flexibility effects on modal parameters (i.e. fundamental frequencies) and time-history analysis response (represented by the top relative displacements) of a 46.8 m high steel lattice tower subjected to a number of ground motions including also one mining tremor. In addition to the fixed-base condition, three different soil...
-
Asymmetrical-Slot Antenna with Enhanced Gain for Dual-Band Applications
PublikacjaDual-band operation is an important feature of antennas to be applied in modern communication systems. Although high gain of radiators is rarely of concern in urban areas with densely located broadcasting stations, it becomes crucial for systems operating in more remote environments. In this work, a dual-band antenna with enhanced bandwidth is proposed. The structure consists of a driven element in the form of an asymmetrical radiator/slot...
-
Cost-Efficient Multi-Objective Design of Miniaturized Microwave Circuits Using Machine Learning and Artificial Neural Network
PublikacjaDesigning microwave components involves managing multiple objectives such as center frequencies, impedance matching, and size reduction for miniaturized structures. Traditional multi-objective optimization (MO) approaches heavily rely on computationally expensive population-based methods, especially when exe-cuted with full-wave electromagnetic (EM) analysis to guarantee reliability. This paper introduces a novel and cost-effective...
-
Fast EM-Driven Nature-Inspired Optimization of Antenna Input Characteristics Using Response Features and Variable-Resolution Simulation Models
PublikacjaUtilization of optimization technique is a must in the design of contemporary antenna systems. Often, global search methods are necessary, which are associated with high computational costs when conducted at the level of full-wave electromagnetic (EM) models. In this study, we introduce an innovative method for globally optimizing reflection responses of multi-band antennas. Our approach uses surrogates constructed based on response...
-
Structure and properties of the exopolysaccharides produced by Pseudomonas mutabilis T6 and P. mutabilis ATCC 31014
PublikacjaThis paper presents a study on the purification, primary structure, and rheological properties of exopolysaccharides isolated from cultures of Pseudomonas mutabilis T6 and P. mutabilis ATCC 31014. Both polymers are exopolysaccharides of D-mannose. The mannan isolated from P. mutabilis T6 contains on average about 5% of residual b-D-glucose, in contrast to the mannan from P. mutabilis ATCC 31014, which contained only trace amounts...
-
Low-strain sensor based on the flexible boron-doped diamond-polymer structures
PublikacjaA free-standing high boron-doped diamond nanosheet (BDDNS) has been fabricated for the development of a flexible BDDNS strain senor. High boron-doped diamond was initially grown on a tantalum substrate in a microwave plasma-assisted chemical vapor deposition method, and was then transferred to a Kapton polymer substrate to fabricate the flexible BDDNS/Kapton device. Before performing the transfer process, the thin BDDNS’s morphology...
-
Female entrepreneurship in Kazakhstan
PublikacjaWomen constitute the majority of the Kazakh population and, even though they live almost 10 years longer than men on average, they are far less economically active. Less than half of the female population take up employment. Women’s wages are often as much as 30% lower than men’s. The subjective reasons for undertaking economic activity as mentioned by women included: independence from the husband, low earnings of the husband and...
-
AMO perspectives on the well-being of neurodivergent human capital
PublikacjaExisting management research and management practices frequently overlook the relationship between the above-average human capital of highly functioning neurodivergent employees, their subjective well-being in the workplace and performance outcomes. This paper calls for greater attention to the hidden human capital associated with neurodiversity by mainstreaming implementation of neurodiversity-friendly policies and practices. Drawing...
-
Ground Tire Rubber Filled Flexible Polyurethane Foam—Effect of Waste Rubber Treatment on Composite Performance
PublikacjaThe application range of flexible polyurethane (PU) foams is comprehensive because of their versatility and flexibility in adjusting structure and performance. In addition to the investigations associated with further broadening of their potential properties, researchers are looking for new raw materials, beneficially originated from renewable resources or recycling. A great example of such a material is ground tire rubber (GTR)—the...
-
Green TPUs from Prepolymer Mixtures Designed by Controlling the Chemical Structure of Flexible Segments
PublikacjaThis study concerns green thermoplastic polyurethanes (TPU) obtained by controlling the chemical structure of flexible segments. Two types of bio-based polyether polyols—poly(trimethylene glycol)s—with average molecular weights ca. 1000 and 2700 Da were used (PO3G1000 and PO3G2700, respectively). TPUs were prepared via a two-step method. Hard segments consisted of 4,4?- diphenylmethane diisocyanates and the bio-based 1,4-butanodiol...
-
Copper(I) halide cluster-based coordination polymers modulated by chiral ditopic dithiodianthranilide ligands: synthesis, crystal structure and photoluminescence
PublikacjaReaction of copper(I) halides with chiral dithiodianthranilidesmdtaandbdtaafforded polymeric complexeswhere polynuclear CuX clusters were linked together by ditopic bridging ligands into 1D chains or 2D layerstructures. In the case of racemic ligands double stranded chain polymers were formed where the Cu4X4(X = I or Br) cores are connected by enantiomeric pairs of the ditopic ligands. In contrast, a homochiralmdtaligand created...
-
An Innovative Antenna Array with High Inter Element Isolation for Sub-6 GHz 5G MIMO Communication Systems
PublikacjaA novel technique is shown to improve the isolation between radiators in antenna arrays. The proposed technique suppresses the surface-wave propagation and reduces substrate loss thereby enhancing the overall performance of the array. This is achieved without affecting the antenna’s footprint. The proposed approach is demonstrated on a four-element array for 5G MIMO applications. Each radiating element in the array is constituted...
-
Workforce mobility against the background of labour market duality theory – the example of selected OECD countries
PublikacjaThe paper aims to present an empirical study of labour market segmentation (LMS) hypothesis. According to the dual labour market theory jobs can be divided into two groups: primary and secondary jobs, with enter barriers into the first one. The primary jobs are usually described with relative high wages, whereas secondary jobs provide lower level of wages. In this paper we first examine the main sectors (according to the ISIC rev....
-
Studies of the separation performance of silanized silica gel for simulated distillation
PublikacjaWe present the results of investigations of the chromatographic (sorptive) properties of silanized silica gel as a stationary phase for gas chromatography used for simulated distillation. Commercially available silanized sorbent (particle diameter range 63–200 m, average pore size 60 Å) was sieved to obtain the 80–100 mesh fraction (180–150 m). The obtained results revealed that silanized silica gel allows the complete separation...
-
Assessment of particular abdominal aorta section extraction from contrast-enhanced computed tomography angiography
PublikacjaThe aim of this work is to improve the accuracy of extraction of a particular abdominal aorta section and to reduce the distortion in three-dimensional Computed Tomography Angiography (CTA) images. Imaging modality and quality plays crucial role in the medical diagnostic process, thus ensuring high quality of images is essential at every stage of acquisition and processing.Noise is defined as a disturbance of the image quality...
-
Face with Mask Detection in Thermal Images Using Deep Neural Networks
PublikacjaAs the interest in facial detection grows, especially during a pandemic, solutions are sought that will be effective and bring more benefits. This is the case with the use of thermal imaging, which is resistant to environmental factors and makes it possible, for example, to determine the temperature based on the detected face, which brings new perspectives and opportunities to use such an approach for health control purposes. The...
-
Boron-Doped Diamond/GaN Heterojunction—The Influence of the Low-Temperature Deposition
PublikacjaWe report a method of growing a boron-doped diamond film by plasma-assisted chemical vapour deposition utilizing a pre-treatment of GaN substrate to give a high density of nucleation. CVD diamond was deposited on GaN substrate grown epitaxially via the molecular-beam epitaxy process. To obtain a continuous diamond film with the presence of well-developed grains, the GaN substrates are exposed to hydrogen plasma prior to deposition....
-
Evaluating Accuracy of Respiratory Rate Estimation from Super Resolved Thermal Imagery
PublikacjaNon-contact estimation of Respiratory Rate (RR) has revolutionized the process of establishing the measurement by surpassing some issues related to attaching sensors to a body, e.g. epidermal stripping, skin disruption and pain. In this study, we perform further experiments with image processing-based RR estimation by using various image enhancement algorithms. Specifically, we employ Super Resolution (SR) Deep Learning (DL) network...
-
Methods of Assessment of Metal Contamination in Bottom Sediments (Case Study: Straszyn Lake, Poland)
PublikacjaThe concentrations of six metals (Zn, Cu, Pb, Ni, Cr, and Cd) were investigated in bottom sediments of Straszyn Lake (North Poland). This study was designed to determine a total content of metals and to assess their mobility and bioavailability. The sequential extraction was used to fractionate metals into five fractions: exchangeable, bound to carbonates, bound to Fe–Mn oxides, bound to organic matter, and residual. The evaluation...
-
Effect of the North Atlantic Thermohaline Circulation on changes in climatic conditions and river flow in Poland
Publikacja: The purpose of this study is to find connections between the North Atlantic Thermohaline Circulation (NA THC), climate elements, such as cloud cover, precipitation, air temperature, sunshine duration, and relative humidity, and flow of rivers in Poland. The intensity of NA THC was characterized by the DG3L index, which was established to assess changes in the amount of heat transported by NA THC along with the transport of water...
-
Analysing the impact of traffic incidents on express road traffic flow using FREEVAL
PublikacjaTraffic incidents occurring on motorways or express roads cause disruptions and deteriorate traffic conditions. The impact will differ depending on the type of incident, its duration and space blocked on the roadway and can be measured with e.g. average speed reduction, extension of travel time, time lost or overall costs of traffic disruptions. The aim of the paper is to analyse this impact, based on data from the Tri-City Ring...
-
A universal NDT method for examination of low energy impact damage in CFRP with the use of TLC film
PublikacjaThe article presents an attempt to use a sheet of laminated thermochromic liquid crystal film (TLC film) for non-destructive testing of the impact damage (energy values: 1J, 2J, 3J and 4J) in carbon fibre-reinforced polymer (CFRP). This is a new, alternative NDT approach based on the thermo-optical effect. The main advantages of this method are a) the low cost of TLC film, b) the low cost of recording devices due to the usage of...