Filtry
wszystkich: 1609
wybranych: 1194
-
Katalog
Filtry wybranego katalogu
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: EXTERNAL VISCOSITY
-
The efficiency of turbomachinery in the zero-and three-dimensional approaches
PublikacjaEfficiency of turbomachinery is usually defined using an isentropic process. This approach provides a reliable reference point only when pressure and temperature measurements are available, e.g. at the casing inlet and outlet. In the case of a single stage internal efficiency determination the reference point is difficult. Computational fluid dynamics allows for an exact calculation of values of losses occurring in a turbine...
-
Effective Friction Angle Of Deltaic Soils In The Vistula Marshlands
PublikacjaThis article presents the results of laboratory tests on soft, normally consolidated soils from the Vistula Marshlands. Samples of high-plasticity organic soils (muds) taken from 3.2–4.0 m and 9.5–10.0 m depth, as well as peat deposit at 14.0 m, are analysed. Presented case study confirms the applicability of the Norwegian Institute of Technology (NTH) method based on Cone Penetration Tests (CPTU) and allows for a conservative...
-
Investigation of functional layers of solid oxide fuel cell anodes for synthetic biogas reforming
PublikacjaSolid oxide fuel cells (SOFCs) are one of the most promising energy conversion devices due to their high efficiency, low pollution and fuel flexibility. Unfortunately, when hydrocarbons are used as a fuel, for example in the form of a biogas, solid carbon can deposit on the anode surface. This process leads to the degradation of the fuel cell performance. A possible solution to this problem is to apply an additional catalytic material,...
-
FURTHER REMARKS ON THE SURFACE VIS IMPRESSA CAUSED BY A FLUID-SOLID CONTACT
PublikacjaIt is well-known that, nano-mechanics should take into account not only physical phenomena occuring within the bulk but, first of all, the physical phenomena appropriate for a surface of two materials contact. The huge volume density of internal surfaces as well countours lines located within the nanomaterial results in our interest in, apart from classical form of mass, momentum and entropy transport, those modes of transportation...
-
Modelling of shear zones during quasi-static granular silo flow using material point method (MPM)
PublikacjaThe paper focuses on confined silo flow of cohesionless sand. The problem considered is a quasi-static flow in a plane strain model silo with parallel walls simulated with the material point method (MPM). The simulation used a non-local hypoplastic constitutive model. Initially, the paper validated the implemented numerical approach with basic element tests and a plane strain compression test. The subsequent MPM calculations for...
-
Improved surface coverage of an optical fibre with nanocrystalline diamond by the application of dip-coating seeding
PublikacjaGrowth processes of diamond thin films on the fused silica optical fibres (10 cm in length) were investigated at various temperatures. Fused silica pre-treatment by dip-coating in a dispersion consisting of detonation nanodiamond (DND) in dimethyl sulfoxide (DMSO) with polyvinyl alcohol (PVA) was applied. Nanocrystalline diamond (NCD) films were deposited on the fibres using the microwave plasma assisted chemical vapour deposition...
-
Laser-textured cross-hatched surface topography analysis with evaluation of high-frequency measurement noise
PublikacjaThe precision of surface roughness determination using ISO 25178 parameters relies on various factors that directly impact the measurement process. In industry applications, the contactless roughness measurement reduces data collection time. However, it introduces several potential errors, including those stemming from the environment. One of the main types of errors encountered during topography analysis is measurement noise,...
-
From ashes to porous hierarchical nanocarbon electrode: Upcycling secondary waste materials through self-catalytic chemical vapour deposition
PublikacjaMetal and metal oxide particles are abundant in various ash-based wastes. Utilizing these as catalyst sources for the fabrication of carbon nanomaterials could present a valuable approach to reduce our reliance on non-renewable and costly catalyst sources, thereby facilitating large-scale nanomaterial production. In this context, secondary waste materials (SWMs) are by-products resulting from the (complete or partial) combustion...
-
Magnetic signature reproduction of ferromagnetic ships at arbitrary geographical position, direction and depth using a multi-dipole model
PublikacjaThe reproduction of magnetic signatures is an important issue concerning the safety of ship traffic, as well as the identification and classification of vessels. Moreover, military applications of magnetic signatures and their reproduction refer to the activation or protection against activation of magnetic naval mines. Previous works on this subject focused on recording and replicating the signatures under the same conditions...
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublikacjaNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Synergistic effect of TiO2 photocatalytic advanced oxidation processes in the treatment of refinery effluents
PublikacjaDifferent types of photolytic and photocatalytic advanced oxidation processes (AOPs) were used for treatment of refinery effluents from bitumen production. The treatment efficiency was evaluated by analyzing chemical oxygen demand (COD), biological oxygen demand (BOD5), volatile organic compounds (VOCs) and sulfide ions concentration. The studies revealed a synergistic effect of application of external oxidants (O3, H2O2, O3/H2O2)...
-
Functional fluorine-doped tin oxide coating for opto-electrochemical label-free biosensors
PublikacjaSensors operating in multiple domains, such as optical and electrochemical, offer properties making biosensing more effective than those working in a single domain. To combine such domains in one sensing device, materials offering a certain set of properties are required. Fluorine-doped tin oxide (FTO) thin film is discussed in this work as functional optically for guiding lossy modes and simultaneously electrochemically, i.e....
-
A Simple Neural Network for Collision Detection of Collaborative Robots
PublikacjaDue to the epidemic threat, more and more companies decide to automate their production lines. Given the lack of adequate security or space, in most cases, such companies cannot use classic production robots. The solution to this problem is the use of collaborative robots (cobots). However, the required equipment (force sensors) or alternative methods of detecting a threat to humans are usually quite expensive. The article presents...
-
Using differential pressure sensor to measure nitrous oxide level in a tank
PublikacjaA method for measuring the level of liquid nitrous oxide oxidizer in a hybrid rocket motor oxidizer tank is proposed. Presented approach is more accurate than the most commonly used method of this measurement, which employs weighting of the whole sounding rocket or an oxidizer tank. In our solution we use a differential pressure sensor to measure the change of pressure at the bottom of an oxidizer tank in comparison to the pressure...
-
Contr-rotating eccentric-mass rotors used as exciters of sinusoidal forces applied to elastically supported bodies
PublikacjaThe work focuses on aspects of multibody dynamics. Investigated object is a mass driven by rotations of an inertial shaker. Resulting vibrational set consists of two counter-rotating identically-unbalanced rotors. Since the mass centres of the rotors do not coincide with the axes of their rotations, significant centrifugal forces arise during rotations. As both rotors are identically unbalanced, the inter-axial force components...
-
Magnetic anisotropy and structural flexibility in the f ield-induced single ion magnets [Co{(OPPh2) (EPPh2)N}2], E = S, Se, explored by experimental and computational methods
PublikacjaDuring the last few years, a large number of mononuclear Co(II) complexes of various coordination geometries have been explored as potential single ion magnets (SIMs). In the work presented herein, the Co(II) S = 3/2 tetrahedral [Co{(OPPh2)(EPPh2)N}2], E = S, Se, complexes (abbreviated as CoO2E2), bearing chalcogenated mixed donor-atom imidodiphosphinato ligands, were studied by both experimental and computational techniques. Specifically,...
-
Machine learning-based seismic response and performance assessment of reinforced concrete buildings
PublikacjaComplexity and unpredictability nature of earthquakes makes them unique external loads that there is no unique formula used for the prediction of seismic responses. Hence, this research aims to implement the most well-known Machine Learning (ML) methods in Python software to propose a prediction model for seismic response and performance assessment of Reinforced Concrete Moment-Resisting Frames (RC MRFs). To prepare 92,400 data...
-
Study of the Resistance to Influence of Aggressive Liquids on Concrete with Lightweight Aggregate
PublikacjaThe corrosion of the structure of concrete caused by the aggressive external environment is one of the main problems that can reduce the durability of buildings. The paper analyzes the influence of the type of component on selected properties of lightweight concrete (LWC) exposed to aggressive liquids. When lightweight concrete containing porous aggregates is used, the influence of an aggressive environment may be of particular...
-
Kontekstowo zorientowany model bezpieczeństwa systemów internetowych
PublikacjaW rozprawie dokonano analizy usługowych systemów internetowych pod względem bezpieczeństwa. Przedstawiono autorskie uniwersalne modele bezpieczeństwa CoRBAC oraz jego rozszerzenie TCoRBAC, będące rozwinięciem tradycyjnego modelu RBAC. Uwzględniono analizę szeroko rozumianego kontekstu funkcjonowania systemu oraz poziom jego zaufania do użytkownika. Opracowano metodę wyznaczania dwóch parametrów: zaufania do systemu (λ) będącego...
-
Jednoelektronowy atom Diraca w słabym polu magnetycznym
PublikacjaW rozprawie przedstawiono opis wpływu zewnętrznego stałego, słabego, jednorodnego pola magnetycznego na jednoelektronowy atom Diraca. Wykorzystując funkcje gęstości ładunku elektrycznego oraz gęstości prądu elektrycznego, rozważono procesy indukowania się w atomie dodatkowych elektromagnetycznych momentów multipolowych. Dokonano analizy indukowanego momentu dipolowego, w wyniku której uzyskano wyrażenie dla magnetyzowalności atomu....
-
A new model of fuel spray shape at early stage of injection in a marine Diesel engine
PublikacjaIn the cylinders of a marine diesel engine, self-ignition occurs in very shortly time after the fuel injection into the combustion chamber. Therefore, the paper present was to develop a model of diesel fuel spray for the early stage of fuel spray for in marine diesel engine. There were taken into consideration the main aspects technical such as nozzle diameter of marine engine injector and backpressure in combustion chamber. In...
-
Engineering Candida albicans glucosamine-6-phosphate synthase for efficient enzyme purification
PublikacjaRationally designed muteins of Candida albicans glucosamine-6-phosphate synthase, an enzyme known as a promising target for antifungal chemotherapy, were constructed, overexpressed in Escherichia coli and purified to near homogeneity. To facilitate and to optimize the purification of the enzyme, three recombinant versionscontaining internal oligoHis fragments were constructed: (i) by substituting residues 343 - 348...
-
Distributed Framework for Visual Event Detection in Parking Lot Area
PublikacjaThe paper presents the framework for automatic detection of various events occurring in a parking lot basing on multiple camera video analysis. The framework is massively distributed, both in the logical and physical sense. It consists of several entities called node stations that use XMPP protocol for internal communication and SRTP protocol with Jingle extension for video streaming. Recognized events include detecting parking...
-
The effect of pre-hydrogen charging on corrosion behaviour of superduplex stainless steel welded joints
PublikacjaThe paper presents results of research undertaken to determine the influence of hydrogen on passivity and corrosion resistance of 2507 super duplex stainless steel welded joints. Butt welded joints were made with low heat input using flux corded arc welding (FCAW) method. Coupons of 5.0 x 5.0 mm were cut from the welded joints containing weld metal (WM), heat affected zone (HAZ) and parent metal (PM). Hydrogen was introduced...
-
CPTU/DMT control of heavy tamping compaction of sands
PublikacjaHeavy tamping compaction method in cohesionless alluvial soil was evaluated with CPTU and DMT tests. Some examples of interpretation of soundings in pre-treated and compacted sands are given. The compaction work was performed in two stages. Compaction control was performed after each stage of tamping. Additional tests were performed two weeks after the compaction works completion to study the set-up effect. While typical increase...
-
MARSTRUCT benchmark study on nonlinear FE simulation of an experiment of an indenter impact with a ship side-shell structure
PublikacjaThis paper presents a benchmark study on collision simulations that was initiated by the MARSTRUCT Virtual Institute. The objective was to compare assumptions, finite element models, modelling techniques and experiences between established researchers within the field. Fifteen research groups world-wide participated in the study. An experiment involving a rigid indenter penetrating a ship-like side structure was used as the case...
-
Time-domain measurement methods for R, L and C sensors based on aversatile direct sensor-to-microcontroller interface circuit
PublikacjatIn the paper new time-domain measurement methods for determining values of resistive (R), inductive(L) and capacitive (C) sensors based on a versatile direct sensor-to-microcontroller interface for microcon-trollers with internal analog-to-digital converters (ADCs) and analog comparators (ACs) are presented.The interface circuit consists of a reference resistor Rrworking as a voltage divider, a given R, L or C sensorand a microcontroller...
-
Multi-mode vibronic interactions in the five lowest electronic states of the fluorobenzene radical cation
PublikacjaThe multi-mode vibronic interactions between the five lowest electronic states of the fluorobenzene radical cation are investigated theoretically, based on ab initio electronic structure data, and employing the linear vibronic coupling model. Low-energy conical intersections, and strong vibronic couplings are found to prevail within the set of X-A and B-C-D cationic states, while the interactions between these two sets of states...
-
Modelization of Nutrient Removal Processes at a Large WWTP Using a Modified ASM2d Model
PublikacjaThe biodegradation of particulate substrates starts by a hydrolytic stage. Hydrolysis is a slow reaction and usually becomes the rate limiting step of the organic substrates biodegradation. The objective of this work was to evaluate a novel hydrolysis concept based on a modification of the activated sludge model (ASM2d) and to compare it with the original ASM2d model. The hydrolysis concept was developed in order to accurately...
-
Dissociative ionization dynamics of dielectric gas C3F7CN
PublikacjaFluoronitrile C3F7CN is a promising candidate for the replacement of SF6 dielectric gas in high-voltage insulation. We present a combined experimental and theoretical study on its ionization dynamics probed in the 0-100 eV energy range. We exploited the total ion collection technique to determine the absolute ionization cross section, mass spectrometry to determine the fragment branching ratios and ab initio nonadiabatic molecular...
-
Analysis of the regenerative braking process for the urban traffic conditions
PublikacjaIn a regular drive system, with an internal combustion engine, vehicle braking is connected with the unproductive dissipation of kinetic and potential energy accumulated in the mass of the vehicle into the environment. This energy can constitute up to 70% of the energy used to drive a vehicle under urban conditions. Its recovery and reuse is one of the basic advantages of hybrid and electric vehicles. Modern traffic management...
-
An integrated geoarchaeological approach to late Iron Age settlement at Kaštelina hillfort (Lopar, Island of Rab, Croatia) using Amplitude Data Comparison (ADC) method and trial excavation
PublikacjaGeophysical prospection and small-scale archaeological excavation were undertaken on the site of Kaštelina, a Late Iron Age hillfort settlement located on the Stolac promontory in the northern part of Rab island (Kvarner Gulf, Croatia). Within the frame of the “Archaeological topography of the island of Rab” program, a Polish–Croatian team applied a series of multidisciplinary methods to study the occupational history of the...
-
Extending loophole-free nonlocal correlations to arbitrarily large distances
PublikacjaQuantum theory allows spatially separated observers to share nonlocal correlations, which enable them to accomplish classically inconceivable information processing and cryptographic feats. However, the distances over which nonlocal correlations can be realized remain severely limited due to their high fragility to noise and high threshold detection efficiencies. To enable loophole- free nonlocality across large distances, we introduce...
-
Characterization of volatile compounds, structural, thermal and physico-mechanical properties of cross-linked polyethylene foams degraded thermo-mechanically at variable times
PublikacjaWaste cross-linked polyethylene foam (wXLPE) was thermo-mechanically degraded at variable time using internal batch mixer. The progress of wXLPE degradation has been investigated by using a simultaneous thermogravimetric/differential scanning calorimetry analyzer coupled with Fourier transform infrared spectroscopy, swelling measurements, tensile tests and scanning electron microscopy. Volatile organic compounds generated during...
-
Chinese Foreign Direct Investments in Europe. The Polish Case
PublikacjaThe first aim of this paper is to analyze the features that have motivated Chinese outbound investments in the European Union. The paper outlines also the policies adopted by the European institutions and its member states to encourage the increase of the Chinese FDI without harming the internal European market, and consequently phase out all concerns that are afflicting the European public opinion. The second purpose is more focused...
-
Effect of Pin Shape on Thermal History of Aluminum-Steel Friction Stir Welded Joint: Computational Fluid Dynamic Modeling and Validation
PublikacjaThis article studied the effects of pin angle on heat generation and temperature distribution during friction stir welding (FSW) of AA1100 aluminum alloy and St-14 low carbon steel. A validated computational fluid dynamics (CFD) model was implemented to simulate the FSW process. Scanning electron microscopy (SEM) was employed in order to investigate internal materials’ flow. Simulation results revealed that the mechanical work...
-
Experimental Studies of Concrete-Filled Composite Tubes under Axial Short- and Long-Term Loads
PublikacjaThe paper presents experimental studies on axially compressed columns made of concrete-filled glass fiber reinforced polymer (GFRP) tubes. The infill concrete was C30/37 according to Eurocode 2. The investigated composite pipes were characterized by different angles of fiber winding in relation to the longitudinal axis of the element: 20, 55 and 85 degrees. Columns of two lengths, 0.4 m and 2.0 m, were studied. The internal diameter...
-
Model of aeration system at biological wastewater treatment plant for control design purposes
PublikacjaThe wastewater treatment plant (WWTP) is a dynamic, very complex system, in which the most important control parameter is the dissolved oxygen (DO) con-centration. The air is supplied to biological WWTP by the aeration system. Aera-tion is an important and expensive activity in WWTP. The aeration of sewage ful-fils a twofold role. Firstly, oxygen is provided as the main component for biolog-ical processes. Secondly, it supports...
-
Cu supported on various oxides as a candidate catalyst for dry methane reforming in DIR-SOFCs systems
PublikacjaA series of Cu-support systems were tested as potential candidates for DIR-SOFC (Direct Internal Reforming SOFC) catalysts towards a dry reforming of methane (DRM). The various supports (-Al2O3, CeO2, ZrO2, SrTiO3) with comparable specific surface area (SSA), and additionally -Al2O3 with SSA an order of magnitude larger than that of the other supports has been applied. The obtained Cu-support systems were characterized in terms...
-
Influence of the Shear Cap Size and Stiffness on the Distribution of Shear Forces in Flat Slabs
PublikacjaThe scope of this paper is to investigate analytically and numerically the influence of shear cap size and stiffness on the distribution of shear forces in flat slabs in a slab–column-connections-reinforced concrete structure. The effect of support (shear cap) stiffness on the calculation of the length of the shear control perimeter according to the available methods is presented. Based on the analysis, the authors indicate in...
-
Verification of punching shear outside the shear cap by the direct method
PublikacjaThe proposition of a method to verify the punching resistance for very large supports based on the EN 1992-1-1 standard is described in this paper. The present standard guidelines for the calculation of the punching resistance for large supports are also summarised. The proposed direct method is compared with other standard methods using an example taken from design practice. This method consists of a direct check of the shear...
-
Micro-modelling of shear localization during quasi-static confined granular flow in silos using DEM
PublikacjaThe paper deals with the quasi-static confined flow of cohesionless sand in a plane strain model silo with parallel walls and a slowly movable bottom. Numerical modelling was carried out by the discrete element method (DEM) using spheres with contact moments to approximately capture a non-uniform shape of sand particles. Different initial void ratios of sand and silo wall roughness grades were employed. Regular triangular grooves...
-
Zaufanie do siebie jako jeden z aspektów zaufania w aktywności przedsiębiorczej
PublikacjaArtykuł prezentuje znaczenie zaufania do samego siebie na tle zaufania w relacjach budowanych przez przedsiębiorcę w jego otoczeniu społecznym i biznesowym. Wyjaśniono koncepcję zaufania do samego siebie, odnosząc się do zróżnicowanych typów zaufania, na przykład: kalkulacyjnego, opartego na wiedzy i identyfikacyjnego. Wskazano jego potencjalne źródła i konsekwencje w kontekście budowania własnego wizerunku, podejmowania decyzji...
-
Survey on fuzzy logic methods in control systems of electromechanical plants
PublikacjaРассмотрены алгоритмы управления электромеханическими системами с использованием теории нечеткой логики, приводятся основные положения их синтеза, рассматриваются методы анализа их устойчивости на основе нечетких функций Ляпунова. Эти алгоритмы чаще всего реализуются в виде различных регуляторов, применение которых целесообразно в системах, математическая модель которых не известна, не детерминирована или является строго нелинейной,...
-
E-egzamin - analiza statystyczna wyników
PublikacjaDnia 4 marca 2008 roku, po raz pierwszy w Polsce, odbył się próbny egzamin gimnazjalny z części matematyczno-przyrodniczej, przeprowadzany drogą elektroniczną, ''E-egzamin 2008''. Organizatorami egzaminu byli: Wyższa Szkoła Humanistyczno-Ekonomiczna i WSiP. Patronat nad projektem objęli: Minister EN i dyrektor Centralnej Komisji Egzaminacyjnej. Nietypowy próbny egzamin gimnazjalny pisało w jednym czasie kilka tysięcy gimnazjalistów...
-
Influence of separation gap on the structural response of colliding structures under earthquake excitation
PublikacjaThe high level of urbanization in the XXIst century forces the designers to design closely-separated structures and to take into account many factors influencing their response during seismic excitation, which are the most unpredictable loads which can affect civil engineering structures. Interactions between insufficiently adjacent buildings, known as the earthquake-induced structural pounding, may cause serious damage to the structures,...
-
CPLFD-GDPT5: High-resolution gridded daily precipitation and temperature data set for two largest Polish river basins
PublikacjaThe CHASE-PL (Climate change impact assessment for selected sectors in Poland) Forcing Data–Gridded Daily Precipitation & Temperature Dataset–5 km (CPLFD-GDPT5) consists of 1951–2013 daily minimum and maximum air temperatures and precipitation totals interpolated onto a 5 km grid based on daily meteorological observations from the Institute of Meteorology and Water Management (IMGW-PIB; Polish stations), Deutscher Wetterdienst...
-
Organisational culture and change management in courts, based on the examples of the Gdańsk area courts
PublikacjaABSTRAKT Background. Courts are by definition bureaucratic, hierarchical organisations, epitomised by low levels of networking potential, which basically lack mechanisms of information exchange, or those of sharing information both at the level of the organisation of the justice system (the macro scale) and within a given court (the micro scale). Research aims. The aims of this article was implementing modern management methods...
-
The metabolic activity of denitrifying microorganisms accumulating polyphosphate in response to addition of fusel oil
PublikacjaThe effect of distillery waste product (fusel oil) as an alternative external organic carbon source (EOCS) was investigated in terms of the metabolic properties of denitrifying polyphosphate accumulating organisms (DPAOs). Samples of the non-acclimated biomass were collected from a local full-scale wastewater treatment plant employing A2/O type bioreactors. The acclimated biomass was obtained after cultivation (with fusel oil added)...
-
Insight into (Electro)magnetic Interactions within Facet-Engineered BaFe12O19/TiO2 Magnetic Photocatalysts
PublikacjaA series of facet-engineered TiO2/BaFe12O19 composites were synthesized through hydrothermal growth of both phases and subsequent deposition of the different, faceted TiO2 nanoparticles onto BaFe12O19 microplates. The well-defined geometry of the composite and uniaxial magnetic anisotropy of the ferrite allowed alternate interfaces between both phases and fixed the orientation between the TiO2 crystal structure and the remanent...