Filtry
wszystkich: 4570
wybranych: 3427
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: VALMEX
-
Influence of Properties of Hydraulic Fluid on Pressure Peaks in Axial Piston Pumps’ Chambers
PublikacjaThe article concentrates on the research of the pressure peaks in a working chamber of an axial piston pump. The main focus of the article is the influence of fluid properties on the pressure peaks value. Experimental and analytical methods were used to determine the impact of the fluid density, viscosity, compressibility and aeration. The article describes the pressure peak generation process and explains the theoretical basis...
-
Overall color parameter as a parameter determining the level of oxidation of olive oil
PublikacjaEdible fats are an important part of a human daily diet. They have a significant effect on the proper functioning of the human body. During frying, the oil is chemically modified and the fats consumed should have the highest oxidation stability. The subject of the study were samples of olive oil bought at local markets in Gdansk. Samples were heated at 20 °C, 60 °C, 100 °C, 140 °C and 180 °C. The aim of the study was to determine...
-
Path dependence, modularity and the offshoring of (some) physician services
PublikacjaThis paper integrates ideas from modularity and path dependency to explain the potential for and limitations of the offshoring of high value added physician services. While not all medical services are amenable to offshoring, a growing number of physician activities can be viewed as modular components which, at least technically, could be performed remotely. As a result, the presumption that concerns for efficiency dictate how...
-
ESTIMATION OF THE WILLINGNESS-TO-PAY FOR PRESERVING THE FOOTBALL ARENA IN GDANSK
PublikacjaThe European Football Championship (Euro 2012) organized in Poland became the pretext for a number of infrastructural changes. A high level of expenditure makes the Polish event the most expensive among events of this magnitude. The fact that these changes were 100% financed by public funds raises the question of whether these funds were used in a substantiated way. Therefore, the aim of this study is...
-
Influence of Different Biofuels on the Efficiency of Gas Turbine Cycles for Prosumer and Distributed Energy Power Plants
PublikacjaThe efficiency of a gas turbine can be affected by the use of different biofuels usually with a relatively Lower Heating Value (LHV). The paper evaluates the impact of calorific value of fuel on turbine performance and analyzes the possibilities of optimizing turbine construction from the point of view of maximum efficiency for a particular fuel. The several variants of design of small power microturbines dedicated to various biofuels...
-
The equivariant spectral flow and bifurcation of periodic solutions of Hamiltonian systems
PublikacjaWe define a spectral flow for paths of selfadjoint Fredholm operators that are equivariant under the orthogonal action of a compact Lie group as an element of the representation ring of the latter. This G-equivariant spectral flow shares all common properties of the integer valued classical spectral flow, and it can be non-trivial even if the classical spectral flow vanishes. Our main theorem uses the G-equivariant spectral flow...
-
Enhanced aging resistance of poly(ε-caprolactone)/brewers’ spent grain composites
PublikacjaThe presented paper investigated the influence of brewers’ spent grain (BSG) extrusion pa-rameters on the photo-oxidative resistance of poly(ε-caprolactone)-based wood polymer composites. Filler samples characterized by the higher melanoidin content were more efficient in hindering of poly-mer degradation, inhibiting the decomposition of the polymer amorphous phase. As aresult, deteriora-tion of mechanical performance was limited,...
-
Infinite chromatic games
PublikacjaIn the paper we introduce a new variant of the graph coloring game and a new graph parameter being the result of the new game. We study their properties and get some lower and upper bounds, exact values for complete multipartite graphs and optimal, often polynomial-time strategies for both players provided that the game is played on a graph with an odd number of vertices. At the end we show that both games, the new and the classic...
-
Fast Approximate String Search for Wikification
PublikacjaThe paper presents a novel method for fast approximate string search based on neural distance metrics embeddings. Our research is focused primarily on applying the proposed method for entity retrieval in the Wikification process, which is similar to edit distance-based similarity search on the typical dictionary. The proposed method has been compared with symmetric delete spelling correction algorithm and proven to be more efficient...
-
Reduction of Computational Complexity in Simulations of the Flow Process in Transmission Pipelines
PublikacjaThe paper addresses the problem of computational efficiency of the pipe-flow model used in leak detection and identification systems. Analysis of the model brings attention to its specific structure, where all matrices are sparse. With certain rearrangements, the model can be reduced to a set of equations with tridiagonal matrices. Such equations can be solved using the Thomas algorithm. This method provides almost the same values...
-
A new approach to active noise and vibration control - [Part II: unknown frequency case]
PublikacjaThis paper presents a new approach to rejection of complex-valued sinusoidal disturbances acting at the output of a discrete-time stable linear plant with unknown and possibly timevarying dynamics. It is assumed that both the instantaneous frequency of the sinusoidal disturbance and its amplitude may be slowly varying with time and that the output signal is contaminated with wideband measurement noise. It is not assumed that a...
-
Some problems of slide bearing material fatigue evaluation.
PublikacjaA slide bearing alloy resistance against fatigue failures have been investigated for three different lubricants, different heat loadings and different stress ratio κ values. The research methods and data handling procedures for determination of particular parameter effects on fatigue strength have been described and analysed for experiments that were set and performed in laboratory tester SKMR-2. Main and interaction effects of...
-
Procesualne kryteria oceny zrównoważonego projektowania architektonicznego
Publikacjaimportance of participation in sustainable design is constantly increasing, as sustainable design becomes a basic idea in architecture. thus mentioning of sustainable design process criteria is authorized. they consist of three following levels: 1) participation in design, 2) participation design, 3) participation design based on the consensus. there is differentia specifica of participation in participatory design because of...
-
THE INFLUENCE OF MANUFACTURING OVERSIZING ON POSTWELDING DISTORTIONS OF THE FILLET WELDED JOINT
PublikacjaWelding proces is basic joining technique in shipbuilding. Such method generated welding distortions which cause a lot of problems during the manufacturing process. In the literature it is proposed wide spectrum of suggestions for a correct estimation of welding deformation in particular angular deformation in the fillet welded T joint. In the work influence of oversizing of weld on angular distortions of joint is presented basing...
-
Numerical analysis of the carpentry joints applied in the traditional wooden structures
PublikacjaThe paper concerns the numerical analysis of the carpentry joints made from spruce wood. The material parameters of the wood have been calculated on the basis of nine independent material constants (an orthotropic material). The contact zone between the individual elements of the connection has been determined using Contact Tables in the MSC.Marc software. Five types of carpentry joints have been analyzed. The main aim of the research...
-
Solid Oxide Fuel Cells with Ni infiltrated perovskite anode
PublikacjaNiobium-doped strontium titanate was used as the anode for a solid oxide fuel cell. Electrolyte-supported cells were prepared with pure perovskite and composite perovskite–yttria–stabilized-zirconia (YSZ) anodes. Fuel cell tests demonstrated significant improvement in power density after infiltration with a small amount of Ni. The obtained values of power densities are comparable with conventional Ni/YSZ cermet anode. In addition,...
-
EXPERIMENTAL STUDY OF A TEMPORARY STEEL GRANDSTAND UNDER CROWD LOAD
PublikacjaTemporary structures, such as grandstands, are commonly used during different types of mass events, especially sport and music concerts. In this paper, the results of the experimental study on temporary steel grandstand are presented. The aim of the investigation was to determine modal characteristics of such structures. Modes of free vibrations and corresponding natural frequencies have been obtained for empty and occupied grandstand....
-
Hydration of urea and its derivatives - Volumetric and compressibility studies
PublikacjaThe densities and sound velocities at T = (288.15, 293.15, 298.15, 303.15 and 308.15) K have been measured for aqueous solutions of urea, N,N-dimethylurea, N,N-diethylurea, N-propylurea, N-butylurea. From these data the apparent molar volumes, V the apparent molar isentropic compressions, KS,, and the Passynski solvation numbers of solutes have been determined. The concentration dependencies of the calculated quantities, their...
-
Estimation of the uncertainty of the LEM CV 3-500 transducers processing function
PublikacjaThe paper presents the methodology for estimating uncertainty of a voltage transducer processing function based on the example of LEM CV 3-500 transducer. The analysis was performed using the method based on the GUM Guide propagation of uncertainty law and the Monte Carlo numerical method. The article also presents a comparative analysis of the results of a voltage measurement evaluation done using the Monte Carlo simulation method,...
-
The system for remote monitoring of a vertical axis wind farm
PublikacjaThe article presents a system for remote monitoring of working parameters of a wind turbine with a vertical axis. The monitoring system was built using a Raspberry PI 3 microcomputer with the Raspbian operating system and a MicroDAQ E2000 measuring card. The developed system enables monitoring the power output of the generator, torque on the turbine shaft, turbine speed and wind speed. The values of the monitored parameters are...
-
Design of optimal state feedback controller with observer for multidimensional electrical system
PublikacjaFrom the control point of view, two-input-two-output RC electrical system is a linear and multidimensional system. In this paper, integral control and closed-loop observer are verified whether they can be used and designed. To verify this, Kalman tests are made. These structures are presented and discussed. Integral Control is tested with some base disturbances impact and checked whether it can handle them. The estimated values...
-
Equitable coloring of corona products of graphs
PublikacjaIn this paper we consider an equitable coloring of some corona products of graphs G and H in symbols, G o H). In particular, we show that deciding the colorability of G o H is NP-complete even if G is 4-regular and H is K_2. Next, we prove exact values or upper bounds on the equitable chromatic number of G o H, where G is an equitably 3- or 4-colorable graph and H is an r-partite graph, a path, a cycle or a complete graph.
-
MEASURE OF THE LEVEL OF SOCIO-ECONOMIC DEVELOPMENT IN PROVINCES
PublikacjaThe scope of Polish macro-economic data for assessing the level of socio-economic development of the country is largely limited because of the regional variation. Therefore there is a need for cyclic selection and the verification of criteria which allow identifying regions with a similar level of socio-economic development or those that clearly differ from the mean values. The aim of the study is to compare Poland’s provinces...
-
Biomechanics of the front abdominal wall as a potential factorleading to recurrence with laparoscopic ventral hernia repair
PublikacjaThis study investigated the front abdominal wallto describe its elasticity in vivo and searched for elongationsthat possibly stretched an implanted mesh, therebycausing fixation failure and subsequent recurrence.To measure front abdominal wall elongations, amodel of fascia movements was created. Eight healthyvolunteers were measured during exercise to determine theextent of elongations in their front abdominal wall. Videoswere...
-
Experimental Verification of Storm Sewer Transient Flow Simulation
PublikacjaThe paper focuses mainly on laboratory investigations of transient and transcritical flow in a single pipe of a sewer system. The aim of this paper is to present a comparison between pressure values calculated by an improved McCormack scheme and those measured at the hydraulic laboratory of the Gdansk University of Technology, which were observed inside a pipe in an experiment for water flow with pressurization. The analysis proves...
-
Consequences of suboptimal design of Building Integrated Photovoltaic Installation – a case study for Gdansk, Poland
PublikacjaThe carried out analysis concerns 2 kWp building integrated photovoltaic installation (BIPV) at the Chemistry Faculty of Gdansk University of Technology. It was proven that the generated energy data for every month diverge significantly from the expected vales. It is corelated with suboptimal orientation of the installation itself, as well as with the tilt angle varying from optimal.
-
Preparation, composition and properties of fish silage produced with post-coagulation sludge
PublikacjaPost-coagulation sludge was added to fish fydrolyzates (silage). Silage was prepared using whole sprats. Technology of the process has been modified and sulphuric acid was replaced with phosphoric acid. The objective was to evaleuate the quality of produced silage during storage, particulary the changes of peroxide value and amount of free acids in silage fat.
-
Nonadaptive estimation of the rotor speed in an adaptive full order observer of induction machine
PublikacjaThe article proposes a new method of reproducing the angular speed of the rotor of a cage induction machine designed for speed observers based on the adaptive method. In the proposed solution, the value of the angular speed of the rotor is not determined by the classical law of adaptation using the integrator only by an algebraic relationship. Theoretical considerations were confirmed by simulation and experimental tests.
-
The noise macromodel of an optocoupler including 1/(f^alfa) noise source
PublikacjaThe course of design of an optocoupler's PSpice macromodel including noise sources is described. The PSpice macromodel is proposed for the low frequency range. The PSpice model of a MOSFET transistor was applied as the noise source type 1/(f^alfa) in an optocoupler PSpice macromodel. In the enhanced macromodel the value of an exponent α can be changed in the range of 0.8 - 1.25.
-
Verification of baffle factor for straight pipe flow
PublikacjaDuring the water disinfection devices designing, it is often assumed that the baffle factor for a straight pipe reactors is equal to one. It would be possible only for the plug flow, which is a simplified model of the flow and does not appear in real situations. The paper contains an equation which enables calculation of the real value of the baffle factor for the pipe flow.
-
NAKŁADY INWESTYCYJNE W SEKTORZE PRZEDSIĘBIORSTW PRYWATNYCH W POLSCE W LATACH 2008-2011. WYBRANE MOŻLIWOŚCI ANALITYCZNE I WIZUALIZACYJNE PROGRAMU R.
PublikacjaW opracowaniu zawarto wraz z przykładami niektóre możliwości programu R Cran w zakresie wizualizacji danych przestrzennych. Analizie poddano nakłady inwestycyjne w poszczególnych województwach w Polsce. Wykazano, że województwa charakteryzujące się wyższym poziomem nakładów inwestycyjnych niż średnia krajowa to województwa: dolnośląskie, łódzkie, mazowieckie, pomorskie i śląskie. Natomiast województwa, w których co roku, obserwuje...
-
Przestrzenie architektury w kontekście zamieszkiwania
PublikacjaPrzestrzeń architektoniczną można analizować w wielu równoległych rozwar-stwieniach zależnych od rozpatrywanego aspektu lub dokonującego się wyda-rzenia. Rozważając proces tworzenia: od idei do formy, poprzez zapis plastycz-ny, mamy do czynienia z przestrzenia kreacji. Związana z nią jest przestrzeń zamysłu odnoszona do ideowych poczynań współodpowiedzialnych za przeka-zywany w obiekcie komunikat. Z przestrzeni tej wywodzą się...
-
Influence of Surface Modification of Titanium and Its Alloys for Medical Implants on Their Corrosion Behavior
PublikacjaTitanium and its alloys are often used for long-term implants after their surface treatment. Such surface modification is usually performed to improve biological properties but seldom to increase corrosion resistance. This paper presents research results performed on such metallic materials modified by a variety of techniques: direct voltage anodic oxidation in the presence of fluorides, micro-arc oxidation (MAO), pulse laser treatment,...
-
Effect of composition on the thermal properties and structure of M-Al-Si-O-N glasses, M = Na, Mg, Ca
PublikacjaThe primary objective of this study is to explore the relationship between the composition, structure, and thermal characteristics of M-Al-Si-O-N glasses, with M representing sodium (Na), magnesium (Mg), or calcium (Ca). The glasses were prepared by melting in a quartz crucible at 1650 °C and AlN precursor (powder) was utilized as a nitrogen source. The measured thermal properties studied were glass transition temperature (Tg),...
-
Surface Texture after Turning for Various Workpiece Rigidities
PublikacjaIn the paper, we present an analysis of the surface texture of turned parts with L/D (length/diameter) ratios of 6 and 12 and various rigidity values. The studies were carried out on samples made of S355JR steel and AISI 304 stainless steel. A detailed analysis of 2D surface profiles was carried out by using a large number of parameters that allowed us to distinguish significant differences in the surface microgeometry, which confirmed...
-
Architecture in the field of art on the example of author’s realizations
PublikacjaThe aim of the article was to show the place of architecture in the space of art on the example of original projects. In the author's opinion, architecture, using an artistic object as a means of expression, influences the process of living by showing the recipient, who is an inhabitant, important values from the point of view of creating a house that ensures a good quality of life and strengthening the understanding of both various...
-
Biowaste chicken eggshell powder as a potential cure modifier for epoxy/anhydride systems: competitiveness with terpolymer-modified calcium carbonate at low loading levels
PublikacjaBiowaste chicken eggshell (ES) powder was applied as a potential cure modifier in epoxy/anhydride systems. Cure behaviour and kinetics of composites filled with very low content (0.1 wt% based on epoxy resin) of ES, calcium carbonate (CaCO3), and terpolymer-modified fillers, mES and mCaCO3, were discussed comparatively. Surface analysis was performed by X-ray photoelectron spectroscopy. Cure kinetics was investigated by differential...
-
Prediction of metal deformation due to line heating; an alternative method of mechanical bending, based on artificial neural network approach
PublikacjaLine heating is one of the alternative methods of forming metals and this kind of forming uses the heating torch as a source of heat input. During the process, many parameters are considered like the size of the substrate, thickness, cooling method, source power intensity, the travel speed of the power source, the sequence of heating, and so on. It is important to analyze the factors affecting the...
-
Combining Computational Fluid Dynamics with a Biokinetic Model for Predicting Ammonia and Phosphate Behavior in Aeration Tanks
PublikacjaThe aim of this study was to use computational fluid dynamics for predicting the behavior of reactive pollutants (ammonia and phosphate) in the aerobic zone of the bioreactor located at the Wschod wastewater treatment plant in Gdansk, Poland. The one-dimensional advection-dispersion equation was combined with simple biokinetic models incorporating the Monod-type expressions as source terms for the two pollutants. The problem was...
-
Bandwidth Dependence of the Propagation Channel in Circular Metallic BAN Environments
PublikacjaIn this paper, the bandwidth dependence of the propagation channel for Body Area Networks (BANs) in circular metallic environments is addressed and models are proposed to evaluate the appropriate short-term fading margins that should be considered as a function of the system bandwidth. The deployment of BANs in metallic indoor environments, such as ships, factories, warehouses and other similar environments, involves additional...
-
Tyre/road noise measurements on ISO tracks using the modified CPX method
PublikacjaTyre rolling noise test method specified in the UNECE Regulation 117 is directly used in the Tyre Labelling Directive. Noise level specified on EU Tyre Label of each new tyre available on the European market was determined based on vehicle coast-by noise measurements performed on the standard reference road surface proscribed in the ISO 10844:2014. Available data from investigations by the vehicle and tyre industry and results...
-
A novel cold-active β-D-galactosidase with transglycosylation activity from the Antarctic Arthrobacter sp. 32cB - gene cloning, purification and characterization
PublikacjaA gene encoding a novel β-D-galactosidase from the psychrotolerant Antarctic bacterium Arthrobacter sp. 32cB was isolated, cloned and expressed in Escherichia coli. The active form of recombinant β-D-galactosidase consists of two subunits with a combined molecular weight of approximately 257 kDa. The enzyme's maximum activity towards o-nitrophenyl-β-D-galactopyranoside was determined as occurring at 28 °C and pH 8.0. However, it...
-
Technical State Assessment of Charge Exchange System of Self-Ignition Engine, Based On the Exhaust Gas Composition Testing
PublikacjaThis paper presents possible use of results of exhaust gas composition testing of self - ignition engine for technical state assessment of its charge exchange system under assumption that there is strong correlation between considered structure parameters and output signals in the form of concentration of toxic compounds (ZT) as well as unambiguous character of their changes. Concentration of the analyzed ZT may be hence considered...
-
The Experimental Determination of Bearings Dynamic Coefficients in a Wide Range of Rotational Speeds, Taking into Account the Resonance and Hydrodynamic Instability
PublikacjaMethods for the experimental determination of dynamic coefficients are commonly used for the analysis of various types of bearings, including hydrodynamic, aerodynamic and foil bearings. There are currently several algorithms that allow estimating bearing dynamic coefficients. Such algorithms usually use various excitation techniques applied to rotor–bearings systems. So far only a small number of scientific publications show how...
-
Experimental investigation of heat transfer enhancement in straight and U-bend double-pipe heat exchanger with wire insert
PublikacjaIn this paper, the possibility of heat transfer enhancement in the U-bend exchanger was presented. Experimental research has been carried out for four individual heat exchanger constructions i.e. plain tube in tube, turbulized tube in tube, plain U-bend and U-bend with turbulator. Also, heat transfer experiments for various boundary conditions were performed to obtain reference values. In case of U-bend exchanger with and without...
-
Numerical investigation on behaviour of cylindrical steel tanks during mining tremors and moderate earthquakes
PublikacjaCylindrical steel tanks are important components of industrial facilities. Their safety becomes a crucial issue since any failure may cause catastrophic consequences. The aim of the paper is to show the results of comprehensive FEM numerical investigation focused on the response of cylindrical steel tanks under mining tremors and moderate earthquakes. The effects of different levels of liquid filling, the influence of non-uniform...
-
The Anti-Staphylococcal Potential of Ethanolic Polish Propolis Extracts
PublikacjaAbstract: The principal objective of this study was to determine the anti-staphylococcal potential of ethanol extracts of propolis (EEPs). A total of 20 samples of propolis collected from apiaries located in different regions of Poland were used in the study. The two-fold broth microdilution method revealed some important differences in the antimicrobial activity of investigated EEPs. Up to the concentration of 4096 µg/mL no activity...
-
Geometric working volume of a satellite positive displacement machine
PublikacjaThis article describes a method for determining the geometric working volume of satellite positive displacement machines (pump and motor). The working mechanism of these machines is satellite mechanism consisting of two non-circular gears (rotor and curvature) and circular gears (satellites). Two variants of the satellite mechanism are presented. In the first mechanism, the rolling line of the rotor is a sinusoid "wrapped" around...
-
Intra-operative biopsy in chronic sinusitis detects pathogenic Escherichia coli that carry fimG/H, fyuA and agn43 genes coding biofilm formation
PublikacjaThe aim of this study was to investigate whether or not surgical biopsy of sinus tissue in chronic sinusitis, not responsive to treatment, would detect E. coli. We intended to evaluate E. coli virulence genes, therefore dispute the causal role of such an unusual microorganism in chronic sinusitis, as well as consider effective pathogen-targeted therapy. Patients with E. coli isolated by intra-operative puncture biopsy were included...
-
Moda jako wartość konsumencka - eksplikacja zagadnienia
PublikacjaCel: Celem artykułu jest przedstawienie problematyki mody jako propozycji wartości dla klienta. Realizacja niniejszego celu wymagała uszczegółowionej eksplikacji zjawiska mody. W publikacji zdefiniowaniu poddano mechanizm działania mody, istotę trendu mody, jak również omówiono główne perspektywy analizy mody oraz aktualne nurty badań nad modą. Projekt badania/metodyka badawcza/koncepcja: W pracy wykorzystano metodę krytycznej...