Filtry
wszystkich: 3175
wyświetlamy 1000 najlepszych wyników Pomoc
Wyniki wyszukiwania dla: GEAR NOISE
-
Barkhausen noise properties measured by different methods for deformed Armco samples
PublikacjaPorównano właściwości sygnału napięciowego efektu Barkhausena (BN) uzyskanego za pomocą 'sondy punktowej' (użytecznej dla badań przemysłowych) oraz cewki otaczającej badany materiał. W pierwszej metodzie mierzono trzy wielkości: V1 - napięcie skuteczne, Nc - liczba impulsów, V2 - napięcie kontrolne z cewki. W drugiej metodzie z napięcia indukowanego w cewce wyznaczano pętlę histerezy B(H), obwiednie z napięcia skutecznego a także...
-
Modeling incipient creep damage effects on Barkhausen noise and magnetoacoustic emission.
PublikacjaZaproponowano model fizyczny opisujący zmiany natężenia efektu Barkhausena i emisji magnetoakustycznej podczas procesu degradacji stali ekploatowanych w przemyśle energetycznym.
-
Measurement of noise parameter set in the low frequency range: requirements and instrumentation.
PublikacjaOpisano dwa podstawowe szumowe modele metrologiczne czwórnika: ze źródłami szumów odniesionymi do wejścia i ze zwarciowymi prądami szumów. Parametry szumowe opisujące modele zawierające korelację pomiędzy prądami i/lub napięciami są mierzone przy zastosowaniu metod bezpośrednich i pośrednich. Przedstawiono kilka technik redukcji szumów własnych systemu pomiarowego. Szerzej zaprezentowano dwukanałowy system do pomiaru szumów z komputerowym...
-
Noise reduction in audio employing spectral unpredictability measure and neural net.
Publikacjamodelu psychoakustycznym zostały przedyskutowane. Uczący się algorytm decyzjny, działający w opraciu o sztuczną sieć neuronową wykorzystany został w klasyfikacji składowych na pasożytnicze i użyteczne. Przedstawiona została również nowa iteracyjna procedura obliczania progu maskowania. W pracy zawarte zostały wyniki eksperymentów, oraz konkluzje odnoszące się do przedstawionych algorytmów.
-
Low frequency noise and DLTS as silicon solar cell characterization tools
PublikacjaPraca zawiera wyniki pomiarów DLTS próbek o powierzchni 1 mm2 krzemowych baterii słonecznych wykazujących znaczne niejednorodności wykryte za pomocą metody LBIV (Light Beam Induced Voltage). Wyniki pomiarów charakterystyk stałoprądowych oraz szumowych tych próbek zostały także przedstawione.
-
Assessment of Fuel Cells’ State of Health by Low-Frequency Noise Measurements
PublikacjaWe proposed applying low-frequency (flicker) noise in proton-exchange membrane fuel cells under selected loads to assess their state of health. The measurement set-up comprised a precise data acquisition board and was able to record the DC voltage and its random component at the output. The set-up estimated the voltage noise power spectral density at frequencies up to a few hundred mHz. We observed the evolution of the electrical...
-
Evaluation of reinforcement corrosion rate in concrete structures by electrochemical noise measurements
PublikacjaW pracy przedstawiono wyniki obliczeń rezystancji polaryzacyjnej w układzie złożonym z dwóch elektrod (ze stali węglowej oraz elektrody odniesienia), umieszczonych w otulinie betonowej. Szybkość korozji ulega zmianom uzależnionym od stopnia nasiąknięcia betonu roztworem zawierającym jony chlorkowe. Zmiany rezystancji polaryzacyjnej elektrody stalowej oceniane są na podstawie pomiarów prądowego i potencjałowego szumu elektrochemicznego....
-
Tire/road noise measuring principles according to the Close Proximity Method
PublikacjaW pracy podano metody badania hałasu opon samochodowych. Omówiono przyczepy pomiarowe zbudowane w Politechnice Gdańskiej oraz systemy pomiarowe stosowane do pomiaru hałasu opon zgodnie z metodą CPX.
-
Quality assessments of electrochromic devices: the possibleuse of 1/f current noise
PublikacjaElementy wykorzystujące zjawisko elektrochromizmu, potrafiące zmieniać przezroczystość za pomocą ładowania/rozładowania ładunkiem elektrycznym, wykonano na bazie laminatów pokrytych porowatą strukturą tlenków Ni oraz tlenków Wi-V. Oba laminaty, na które naniesiono przewodzącą warstwę In2O3, przedzielono warstwą elektrolitu. Obserwowano szumy typu 1/f w prądzie I płynącym w trakcie rozładowywania urządzenia. Gęstość widmowa mocy...
-
Analysis of the Usefulness of Cheap Audio Recorders for Spectral Measurement of Environmental Noise
PublikacjaEnvironmental noise pollution is nowadays one of the most serious health threats. The impact of noise on the human body depends not only on the sound level but also on its spectral distribution. Reliable measurements of the environmental noise spectrum are often hampered by the very high price of top quality measuring devices. This paper explores the possibility of using much cheaper audio recorders for the frequency analysis....
-
Investigating Noise Interference on Speech Towards Applying the Lombard Effect Automatically
PublikacjaThe aim of this study is two-fold. First, we perform a series of experiments to examine the interference of different noises on speech processing. For that purpose, we concentrate on the Lombard effect, an involuntary tendency to raise speech level in the presence of background noise. Then, we apply this knowledge to detecting speech with the Lombard effect. This is for preparing a dataset for training a machine learning-based...
-
A review of design approaches for the implementation of low-frequency noise measurement systems
PublikacjaElectronic noise has its roots in the fundamental physical interactions between matter and charged particles, carrying information about the phenomena that occur at the microscopic level. Therefore, Low-Frequency Noise Measurements (LFNM) are a well-established technique for the characterization of electron devices and materials and, compared to other techniques, they offer the advantage of being non-destructive and of providing...
-
Implementation of constant component filter in measurements of random telegraph signal noise
PublikacjaNoise is generated in all semiconductor devices. The intensity of these fluctuations depends on used elements, manufacturing process, operating conditions and device type. The result noise is a superposition of different kinds of fluctuations like thermal noise, generation-recombination noise, 1/f noise, shot noise and Random Telegraph Signal (RTS) noise. The last one, RTS noise is observed as nonstationary impulse fluctuations....
-
Low noise poroelastic road pavements based on modified asphalt binder
PublikacjaTire/road noise is one of the most important environmental problems related to road traffic. As the most effective way to fight noise is reduction of sound emission from the source, a lot of work is being done to improve tire and road surfaces construction. This paper describes the first “road” results obtained within the SEPOR project, which is focused on developing a low noise poroelastic road surface based on bituminous binder....
-
Rolling resistance and tyre/road noise on rubberised asphalt pavement in Poland
PublikacjaThe paper presents results of tyre/road noise and rolling resistance measurements performed on stone mastics asphalt (SMA) that contains rubberised asphalt, developed and produced by a refinery in Poland. Bituminous binder was modified with polymer and addition of crumb rubber. The first observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger...
-
Rolling Resistance And Tire/Road Noise on Rubberized Asphalt Pavement In Poland
PublikacjaThe paper presents results of tire/road noise and rolling resistance measurements performed on stone-matrix asphalt (SMA) that contains rubberized asphalt developed and produced by the company in Poland. Bituminous binder was modified with polymer and additive of crumb rubber. First observations of asphalt mixture with the new kind of modified bitumen used on the field section are presented. Rolling resistance of passenger car...
-
Three solvers for MIMO noise radar clutter cancellation - a performance comparison
PublikacjaThe problem of canceling strong clutter echos in a MIMO noise radar is considered. Execution times of three algorithms is compared. The first solution is a standard Least Squares approach employing Cholesky decomposition of the transmitted signal sample autocorrelation matrix. The second approach is based on careful waveform design which guarantees that the signal sample autocorrelation matrix has Toeplitz structure. This enables...
-
Tracking of the broadband source of the underwater noise in the very shallow water conditions
PublikacjaThe paper contains the result s, both theoretical and experimental , connected with the tracking of the underwater noise source as small ships, pontoon , diver and so on. The pro blem of security in the shallow water area is the challenge for underwater acousticians. In this paper there is take n into account the detection of the sources that move on the surface of the sea or underwater in shallow...
-
Tire/Road Noise On Poroelastic Road Surfaces - Results Of Laboratory Measurements
PublikacjaTire/road noise is the most important part of traffic noise for medium and high speed driving both in the case of passenger cars and trucks. The potential to make modification of tires that significantly reduce tire/road noise in nearly over, at least for conventional tires so the only promising action is to improve road pavements. One of the innovative solutions is poroelastic road pavement (PERS) that reduces airflow related...
-
Review and comparison of smoothing algorithms for one-dimensional data noise reduction
PublikacjaThe paper considers the choice of parameters of smoothing algorithms for data denoising. The impact of the window size on smoothing accuracy was analyzed. The parameters of denoising filters were selected with respect to the meansquare error between the computed linear regression and the noisy signal. Finally, we have compared mean, median, SavitzkyGolay, Kalman and Gaussian filter algorithms for the data from the digital sensor....
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublikacjaRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
TIRE/ROAD NOISE AND TIRE ROLLING RESISTANCE ON PROTOTYPE PERS SURFACE
PublikacjaPoroelastic road surfaces are characterized by low noise of tires running on them.Road pavements of this type are promising solution to problems related to traffic noise in cities and on rural roads. Some technical problems still have to be solved, in particular regarding durability and skid resistance on wet surface. Ongoing and planned works are to contribute to create a quiet, durable and safe road surface, which will become...
-
Reduction of road traffic noise by source measures — present and future strategies
PublikacjaThe current trend worldwide is less focused on reducing road traffic noise. This is in strong contrast to the severe impact of traffic noise to the general health and quality of life. A more holistic and combined strategy is needed. Current international rules and regulations regarding vehicles and tyres are not sufficient to reduce traffic noise levels in an effective way. Calculations show that these regulations will only yield...
-
ROSANNE Project: New Procedure for Noise Characterisation of Road Surfaces in Europe
PublikacjaROSANNE is a collaborative project in the 7th EU Framework Programme which aims at harmonising measurement methods for skid resistance, noise emission and rolling resistance of road pavements as a preparation for standardization. The project started in November 2013 and is developing and improving standards in the field of working group CEN/TC 227/WG 5. Regarding the influence of the pavement on the road traffic noise emission,...
-
Realistic noise-tolerant randomness amplification using finite number of devices
PublikacjaRandomness is a fundamental concept, with implications from security of modern data systems, to fundamental laws of nature and even the philosophy of science. Randomness is called certified if it describes events that cannot be pre-determined by an external adversary. It is known that weak certified randomness can be amplified to nearly ideal randomness using quantum-mechanical systems. However, so far, it was unclear whether randomness amplification...
-
Signal conditioning for examination of shallow-water acoustic noise correlation properties
PublikacjaThe article describes the process of signal conditioning for examination of acoustic noise correlation properties in shallow water. Knowledge of these properties is very important for the design processes of passive and active hydroacoustic systems. This paper focuses on the above issue from the point of view of passive sonar. In sonar systems, signal processing algorithms operate on both useful acoustic signals, and accompanying...
-
On the Handling of Outliers in the GNSS Time Series by Means of the Noise and Probability Analysis
PublikacjaThe data pre-analysis plays a significant role in the noise determination. The most important issue is to find an optimum criterion for outliers removal, since their existence can affect any further analysis. The noises in the GNSS time series are characterized by spectral index and amplitudes that can be determined with a few different methods. In this research, the Maximum Likelihood Estimation (MLE) was used. The noise amplitudes...
-
Low-frequency noise in ZrS3 van der Waals semiconductor nanoribbons
PublikacjaWe report the results of the investigation of low-frequency electronic noise in ZrS3 van der Waals semiconductor nanoribbons. The test structures were of the back-gated field-effect-transistor type with a normally off n-channel and an on-to-off ratio of up to four orders of magnitude. The current–voltage transfer characteristics revealed significant hysteresis owing to the presence of deep levels. The noise in ZrS3 nanoribbons...
-
Journal of Ancient Near Eastern Religions
Czasopisma -
Australian Year Book of International Law
Czasopisma -
Journal of Balkan and Near Eastern Studies
Czasopisma -
The potential of the application of biodegradable and non‐toxic base oils for the formulation of gear oils — model and component scuffing tests
Publikacja -
Simulation of the profile wear of the tool in double wheel lapping
PublikacjaW pracy przedstawiono model zużycia narzędzia w docieraniu dwutarczowym. Wyprowadzono równania opisujące kontakt przedmiotu z narzędziem. Przedstawiono wyniki analiz symulacyjnych dla różnych parametrów kinematycznych - dla układu współbieżnego i przeciwbieżnego.
-
Active farmsteads are year-round strongholds for farmland birds
Publikacja -
A preliminary study for identifying olfactory markers of fear in the rat
PublikacjaW sytuacjach stresowych wiele zwierząt wydziela feromony alarmowe aby ostrzec inne osobniki o nieuchronnym zagrożeniu. Autorzy szukali warunków doświadczalnych, mających na celu identyfikację feromonów alarmowych wydzielanych przez szczury. Szczury umieszczono w specjalnie zaprojektowanych komorach i narażono na różne dotykowe, wizualne i akustyczne bodźce w przeciągu kilku dni. Badacze obserwowali zachowanie szczurów i analizowali...
-
The Rolling Contact Fatigue of PVD Coated Spur Gears
Publikacja -
The Effect of Temperature on Wear Mechanism of the AlCrN Coated Components
Publikacja -
Effect of wear on EHD film thickness in sliding contacts
Publikacja -
Wear of Electroplated Tools Used for Flat Grinding of Ceramics
PublikacjaTwo methods for the abrasive properties evaluation, based on the image processing, are presented in the paper. Image processing analysis was developed to evaluate quickly the abrasive properties as the tool wears down. The coefficient based on the image brightness was calculated and additional analysis was based on the number of grains located on the active surface of the tool before and after machining. The active surfaces of...
-
A study to identify olfactory markers of fear in rats and humans
PublikacjaW pracy przedstawiono wyniki wstępnych badań ukierunkowanych na wykrycie podstawowych fermonów wydzielanych w sytuacji zagrożenia (fermony alarmowe) przez różne organizmy żywe.W badaniach zastosowano takie techniki jak TD-GC-MS, SPME-GC-MS stwierdzono występowanie fermonów należących do takich klas związków organicznych jak alkohole, węglowodory nasycone, aldehydy, kwasy karboksylowe i ketony.
-
Olfactory and tissue markers of fear in mammals including humans
PublikacjaW pracy przedstawiono informacje na temat:-klasyfikacji i budowy chemicznej związków chemicznych zaliczanych do grupy feromonów,-ich rola w funkcjonowaniu organizmów żywych w tym także organizmu ludzkiego,wyników badań prowadzonych z wykorzystaniem komory ekspozycyjnej własnej konstrukcji,metodyk analitycznych wykorzystywanych do oznaczania śladowych zawartości feromonów w próbkach wydychanego powietrza.
-
Simulation of the profile wear of the tool in double wheel lapping
PublikacjaPrzedstawiono założenia modelowe do wyznaczenia zużycia profilowego narzędzia w docieraniu dwutarczowym. Rozkłady istotnych czynników kinematycznych (prędkości docierania i przyspieszenia stycznego) wpływających na zużycie docieraka zaprezentowane zostały dla różnych typów zakreślanych trajektorii.
-
Comparative investigation of lubricant properties in friction and wear tests
PublikacjaOpisano porównawcze badania obciążenia zacierania na tribometrze PT3, obciążenia zespawania na aparacie czterokulowym i zużycia frettingowego na stanowisku FRET3, sześciu olejów smarowych i sześciu smarów plastycznych. Próbki do badań na stanowiskach PT3 i FRET3 wykonane były ze stali 35.
-
Estimation of wear of electroplated tools used for surface grinding
PublikacjaW pracy dokonano ilościowej oceny zużycia narzędzi galwanicznych diamentowych i borazonowych. Wykorzystano analizę jasności obrazów narzędzi oraz badano liczność ziaren ściernych na czynnej powierzchni narzędzia.
-
Tool Wear Prediction in Single-Sided Lapping Process
PublikacjaSingle-sided lapping is one of the most effective planarization technologies. The process has relatively complex kinematics and it is determined by a number of inputs parameters. It has been noted that prediction of the tool wear during the process is critical for product quality control. To determine the profile wear of the lapping plate, a computer model which simulates abrasive grains trajectories was developed in MATLAB. Moreover,...
-
On stress singularity near the tip of a crack with surface stresses
PublikacjaIn the framework of the simplified linear Gurtin–Murdoch surface elasticity we discuss a singularity of stresses and displacements in the vicinity of a mode III crack. We show that inhomogeneity in surface elastic properties may significantly affect the solution and to change the order of singularity. We also demonstrate that implicitly or explicitly assumed symmetry of the problem may also lead to changes in solutions. Considering...
-
Wear of the tool in double-disc lapping of silicon wafers
PublikacjaPrzedstawiono założenia modelowe do określania zużycia narzędzia w docieraniu krzemowych płytek półprzewodnikowych. Obliczenia zostały wykonane dla różnych parametrów kinematycznych, wpływających na zużycie narzędzia w określonych jego obszarach.
-
Chemical and Mechanical Properties of 70-Year-Old Concrete
PublikacjaThe aim of this research is to determine the durability and strength of concrete continuous footing based on the chosen mechanical, physical, and chemical properties of the concrete. The presented investigations constitute some opinions from experts on the bearing capacity of concrete continuous footing and the possibilities of carrying additional loads and extended working life. The cylindrical specimens were taken from continuous...
-
WEAR OF Si OR B DOPED AMORPHOUS CARBON COATINGS
PublikacjaThe paper describes a complex wear research on DLC (amorphous carbon) moped with boron (B) and silicone (Si). The tests were carried out in two different sliping systems: flat–on–flat (ring contact, unidirectional sliding) and ball–on–flat (reciprocating sliding). Water and medical saline solutions were used as lubricants. A comparative analysis of the results revealed differences in the initiation and progress of wear and the...
-
Systèmes de pensée en Afrique noire
Czasopisma