Filters
total: 1811
filtered: 1591
displaying 1000 best results Help
Search results for: elastic wave propagation
-
Investigation of abdomen surface deformation due to life excitation: implications for implant selection and orientation in laparoscopic ventral hernia repair
PublicationVentral hernia is a common medical problem. Statistically there are around 10% recurrences of the sickness. The authors' former investigation proved edges of the hernia orifice displacements to be one of the factors causing recurrence. Thus, experimental investigation of the abdomen surface deformation due to some normal activities of people is studied.The extreme strains, their localization and directions are identified. The acquired...
-
FEM ANALYSIS AND EXPERIMENTAL TESTS OF RIGID RISER HANGING SYSTEM
PublicationThe article presents the analysis, project, and experimental examination of an original rigid riser for Coil Tubing Pipes. The principle of riser operation is based on the use of friction forces. The research included the FEM analysis of the designed riser, calculations of the required bolt tensions, and checking the effect of the clamping force on stress distribution in the pipeline. The results of computer simulation were verified...
-
Design of septic tanks placed on cohesive soils
PublicationThe paper presents a short review of literature with regard to design and erection of the reinforced concrete and concrete tanks. The authors investigated the underground septic tank with of 10 m3 capacity placed on cohesive soils. The authors compared the values of internal forces for soils in drained and undrained conditions with different geotechnical parameters: loamy sand of liquidity index IL = 0.1 and IL = 0.7 and clay with...
-
On stress singularity near the tip of a crack with surface stresses
PublicationIn the framework of the simplified linear Gurtin–Murdoch surface elasticity we discuss a singularity of stresses and displacements in the vicinity of a mode III crack. We show that inhomogeneity in surface elastic properties may significantly affect the solution and to change the order of singularity. We also demonstrate that implicitly or explicitly assumed symmetry of the problem may also lead to changes in solutions. Considering...
-
A New Direct-Sequence Spread Spectrum Signal Detection Method for Underwater Acoustic Communications in Shallow-Water Channel
PublicationDirect-Sequence Spread Spectrum (DSSS) is one of the modulation and coding techniques used in Underwater Acoustic Communication (UAC) systems for reliable data transmision even at low signal levels. However, in a shallow water channel, there is a strong multipath propagation which causes a phase fluctuation of the received signal, affecting the performance of the spread-spectrum system. The article presents a differential method...
-
Detection of the First Component of the Received LTE Signal in the OTDoA Method
PublicationIn a modern world there is a growing demand for localization services of various kinds. Position estimation can be realized via cellular networks, especially in the currently widely deployed LTE (Long Term Evolution) networks. However, it is not an easy task in harsh propagation conditions which often occur in dense urban environments. Recently, time-methods of terminal localization within the network have been the focus of attention,...
-
Multi-Taper-Based Automatic Correction of Non-Anechoic Antenna Measurements
PublicationPrototype measurements belong to the key steps in the development of antenna structures. Although accurate validation of their far-field performance can be realized in dedicated facilities, such as anechoic chambers, the high cost of their construction and maintenance might not be justified if the main goal of measurements is to support teaching or low-budget research. Instead, they can be performed in non-anechoic conditions and...
-
Unusual dynamics and nonlinear thermal self-focusing of initially focused magnetoacoustic beams in a plasma
PublicationUnusual thermal self-focusing of two-dimensional beams in plasma which axis is parallel to the equilibrium straight magnetic field is considered. The equi- librium parameters of plasma determine scenario of a beam divergence (usual or unusual) which is stronger as compared with a flow without magnetic field. Nonlinear thermal self-action of a magnetosonic beam behaves differently in the ordinary and unusual cases. Damping of wave...
-
Revisiting Toroidal Dipolar Moment in Planar Metamaterial
PublicationThis article revisits the electric, magnetic, and toroidal dipolar moments in the metamaterial structure and presents the flatland design for generating a toroidal dipolar response for the electromagnetic plane wave at normal incidence. Based on the numerical analysis of the surface current, the electric field, the magnetic field, and the quantitative analysis of scattered power supported by the electromagnetic multipole theory,...
-
The Application Of A Noise Mapping Tool Deployed In Grid Infrastructure For Creating Noise Maps Of Urban Areas
PublicationThe concept and implementation of the system for creating dynamic noise maps in PL-Grid infrastructure are presented. The methodology of dynamic acoustical maps creating is introduced. The concept of noise mapping, based on noise source and propagation models, was developed and employed in the system. The details of incorporation of the system to the PL-Grid infrastructure are presented. The results of simulations performed by...
-
Specification of private art galleries used in the central part of old town Belgrade
PublicationIn Belgrade, since the late 1990s, private art galleries have appeared that indirectly create the image of the city through the propagation of art, take part in the education process of the residents and undertake criticism of local and global events. The article is an answer to the following questions: [1] why and how do the bottom-up art oriented places appear in Belgrade, [2] how do they function, and (3) what is their architectural...
-
Ocena wpływu dawki DME na wybrane wskaźniki procesu spalania w dwupaliwowym silniku o zapłonie samoczynnym
PublicationPrzedmiotem rozprawy jest analiza wpływu różnej ilości odparowanego DME wprowadzonego do kolektora dolotowego na wybrane wskaźniki spalania DME/ON dla wielu punktów pracy, turbodoładowanego silnika o zapłonie samoczynnym. Jako punkty pracy silnika, wybrano punkty najbardziej reprezentujące cykl jazdy WLTP dla samochodu Volkswagen Golf IV. Analizę procesu współspalania przeprowadzono z wykorzystaniem danych pomiarowych, uzyskanych...
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublicationWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Torsional elasticity and energetics of F1-ATPase
PublicationFoF1-ATPase is a rotary motor protein synthesizing ATP from ADP driven by a cross-membrane proton gradient. The proton flow through the membrane-embedded Fo generates the rotary torque that drives the rotation of the asymmetric shaft of F1. Mechanical energy of the rotating shaft is used by the F1 catalytic subunit to synthesize ATP. It was suggested that elastic power transmission with transient storage of energy in some compliant...
-
Assessment of Thermal Stresses in Asphalt Mixtures at Low Temperatures Using the Tensile Creep Test and the Bending Beam Creep Test
PublicationThermal stresses are leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when the temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature...
-
Kinedynamics of Spherical Wavefields in Fluid and Dielectric Continua
PublicationDistubances induced by physical sources in fluids or dielectrics maintain their primary character while propagating throughout either of these bi-dynamic continua. The paper defines and illustrates four sets of bi-fields based on four specific fundamental kinedynamic solutions to inhomogeneous wave equations related to quasi-point acoustic and electromagnetic sources.
-
An Analysis of Periodic Arrangements of Cylindrical Objects of Arbitrary Convex Cross Sections with the Use of Field Matching Method
PublicationA problem of electromagnetic wave scattering from multilayered frequency selective surfaces is presented. Each surface is composed of periodically arranged cylindrical posts of arbitrary convex cross-section. The method of analysis is based on the direct field matching technique for a single cell, and the transmission matrix method with the lattice sums technique for periodic arrangement of scatterers.
-
Routing decisions independent of queuing delays in broadband leo networks
PublicationThis paper presents an analysis of queuing and propagation delays of Inter-Satellite Links (ISLs) in broadband Low-Earth Orbit (LEO) satellite networks. It is shown that queuing delays are negligible in all reasonable working conditions of the broadband ISL network. This fact makes it possible to simplify the routing protocols in such networks and permits using already known multi-commodity flow solutions for routing. The performance...
-
Path Loss Modelling for Location Service Applications
PublicationThe aim of this paper is the path loss modeling for the radiolocation services in radiocommunication networks, particularly in cellular networks. The main results of the measurements obtained in the physical layer of the UMTS are introduced. A new method for the utilization of the multipath propagation phenomenon to improve the estimation of the distance between the mobile station (MS) and the base station (BS) is outlined. This...
-
Estimation of transmission quality in cellular systems based on indicators measured by the radio module
PublicationThe article presents a measurement stand for testing transmission quality in cellular systems such as LTE, NB-IoT, UMTS and GSM. The results of BLER and throughput measurements for various propagation conditions as well as results of quality indicators appropriate for mentioned technologies measured by commercial radio module are presented. Those measurements were utilized to analyze the possibility of estimating the transmission...
-
Application of a cellular automaton to simulations of granular flow in silos
PublicationA cellular automaton based on a gas model of hydrodynamics was used to calculate the kinematics of non-cohesive granular materials during confined flow in a mass flow and funnel flow model silo. In the model, collisions of particles were taken into account during granular flow. In addition, a simplified automaton was used wherein granular flow was assumed as an upward propagation of holes through a lattice composed of cells representing...
-
DETEKCJA FAL UDERZENIOWYCH W UKŁADACH ŁOPATKOWYCH CZĘŚCI NISKOPRĘŻNYCH TURBIN PAROWYCH
PublicationW artykule przedstawiono wyniki numerycznych symulacji okołodźwiękowego przepływu pary przez ostatnie stopnie części niskoprężnej turbiny o mocy 50 MW. Celem przeprowadzonych symulacji była detekcja oraz lokalizacja fali uderzeniowej, występującej dla przyjętej geometrii układu łopatkowego. Przeanalizowano również wpływ zmiany wartości ciśnienia na wlocie do rozpatrywanych stopni turbiny na maksymalną wartość...
-
Evaluation of thermal cracking probability for asphalt concretes with high percentage of RAP
PublicationThe paper presents determination of the probability of thermal cracking of asphalt mixtures with different reclaimed asphalt pavement (RAP) content on the basis of laboratory tests and analytical evaluation using thermal stress development method. Probability was evaluated taking into consideration: the type and gradation of the mixture and the quality and content of RAP. Thermal stresses were determined using two models: elastic and...
-
Influence of nodes with positive eccentricity on load-carrying capasity of truss' top chords in trusses made of welded cold-formed members.
PublicationIn order to establish the influence of eccentric crossing of truss members on the load-carrying capacity of the folded chord of a hat-section truss, a research model was created and preliminary numerical analysis of the truss was performed with the use of Marc Mentat programme. Distorial instability of crossheads caused by deviation of loose (unmounted) channel section web’s bends was observed. Due to the slenderness of the section’s...
-
On the material symmetry group for micromorphic media with applications to granular materials
PublicationWithin the framework of the theory of nonlinear elastic micromorphic continua we introduce the new definition of the local material symmetry group. The group consists of ordered triples of second- and third-order tensors describing such changes of a reference placement that cannot be recognized with any experiment. Using the definition we characterize the micromorphic isotropic media, micromorphic fluids, solids and special intermediate...
-
Vibration of the bridge under moving singular loads - theoretical formulation and numerical solution
PublicationThe paper presents the results of the numerical analysis of a simple vehicle passing over a simply supported bridge span. The bridge is modelled by a Euler-Bernoulli beam. The vehicle is modelled as a linear, visco-elastic oscillator, moving at a constant speed. The system is described by a set of differential equations of motion and solved numerically using the Runge-Kutta algorithm. The results are compared with the solution...
-
Kompensacja skoków ciśnienia w pompie tłoczkowej o zmiennej wydajności z rozrządem krzywkowym
PublicationPrzedmiotem rozprawy doktorskiej jest opis matematyczny, badania i symulacja mechanizmu kompensacji skoków ciśnienia w pompie tłoczkowej z rozrządem krzywkowym typu PWK. W rozprawie przedstawiono istniejące rozwiązania konstrukcyjne pomp tłokowych, kładąc szczególny nacisk na przedstawienie stosowanych w nich mechanizmów rozrządu i kompensacji skoków ciśnienia. Ponadto szczegółowo opisano budowę i zasadę działania pompy PWK będącej...
-
An Efficient Framework For Fast Computer Aided Design of Microwave Circuits Based on the Higher-Order 3D Finite-Element Method
PublicationIn this paper, an efficient computational framework for the full-wave design by optimization of complex microwave passive devices, such as antennas, filters, and multiplexers, is described. The framework consists of a computational engine, a 3D object modeler, and a graphical user interface. The computational engine, which is based on a finite element method with curvilinear higher-order tetrahedral elements, is coupled with built-in...
-
Dimensionally Consistent Nonlinear Muskingum Equation
PublicationAlthough the Muskingum equation was proposed nearly 75 years ago, it is still a subject of active research. Despite of its simple form, the real properties of this equation have not been comprehensively explained. This paper proposes a new interpretation of the linear McCarthy’s relation. This relation can be interpreted only together with the storage equation, whereas the Muskingum equation can be derived directly from the system...
-
Hysteresis curves for some periodic and aperiodic perturbations in magnetosonic flow
PublicationA thermodynamic relation between perturbations of pressure and mass density in the magnetohydrodynamic flow is theoretically studied. Planar magnetohydrodynamic perturbations with the wave vector, which forms a constant angle with the equilibrium magnetic field, are under study. The theory considers thermal conduction of a plasma and the deviation from adiabaticity of a flow due to some kind of heating–cooling function. It also...
-
Non-Contact Monitoring of ECG in the Home Environment—Selecting Optimal Electrode Configuration
PublicationCapacitive electrocardiography (cECG) is most often used in wearable or embedded measurement systems. The latter is considered in the paper. An optimal electrocardiographic lead, as an individual feature, was determined based on model studies. It was defined as the possibly highest value of the R-wave amplitude measured on the back of the examined person. The lead configuration was also analyzed in terms of minimizing its susceptibility...
-
The nonlinear effects of sound in a liquid with relaxation losses
PublicationThe nonlinear effects of sound in electrolyte with a chemical reaction are examined. The dynamic equations that govern non-wave modes in the field of intense sound are derived, and acoustic forces of vortex, entropy, and relaxation modes are determined in the cases of low-frequency sound and high-frequency sound. The difference in the nonlinear effects of sound in electrolyte and in a gas with excited vibrational degrees of molecules,...
-
Substrate-integrated waveguide (SIW) filter design using space mapping
PublicationIn this paper, we present a fast technique for an automated design of microwave filters in substrate integrated wave (SIW) technology. The proposed methodology combines the space mapping technique with a cost function defined using the location of complex zeros and poles of filter’s transfer and reflection function and uses a rectangular waveguide as a surrogate model. The effectiveness of the proposed technique is presented with...
-
Radio Link Measurement Methodology for Location Service Applications
PublicationThe aim of this paper is the methodology of measurements executed in a radio link for the realization of radiolocation services in radiocommunication networks, particularly in cellular networks. The main results of the measurements obtained in the physical layer of the universal mobile telecommunications system (UMTS) are introduced. A new method for the utilization of the multipath propagation phenomenon to improve the estimation...
-
Software for calculation of noise maps implemented on the supercomputer
PublicationThis paper presents investigation results relevant to the implementation of the algorithms for the calculation of noise maps. The aim of the implementation of the algorithms on the computer cluster is explained. Selected implementation details of the software called the noise propagation model are described. The interaction of the software with the data acquisition system is presented. Noise maps obtained by exploitation of the...
-
Analysis of sloping brace stiffness influence on stability and load bearing capacity of a truss
PublicationThe paper is focused on the numerical study of stability and load bearing capacity of a truss with side elastic braces. The structure is made in reality. The rotational and sliding brace stiffnesses were taken into account. Linear buckling analysis and non-linear static analysis with geometric and material nonlinearity were performed for the beam and shell model of the truss with respect to the angle of sloping braces. As a result...
-
Effect of underwater local cavity welding method conditions on diffusible hydrogen content in deposited metal
PublicationOne of the methods with great potential for applications in underwater repairs is local cavity welding. In local cavity method, cooling conditions and diffusible hydrogen amount in weld metal are nearly the same as those existed during welding in the air. This paper presents the results of literature survey and preliminary tests of the effect of local cavity welding conditions on diffusible hydrogen amount in a deposited metal....
-
Low-energy positron scattering from gas-phase uracil
PublicationQuantum scattering calculations are presented for the interaction of low energy positrons with the uracil molecule, an important component of biological systems. The rotational elastic and inelastic cross sections and vibrational inelastic cross sections are reported and compared with existing experiments, indicating a general trend of the cross sections different from the experimental findings and in line with what should be expected...
-
Elastoplastic nonlinear FEM analysis of FGM shells of Cosserat type
PublicationThe paper is a continuation of [1] where the formulation of the elastic constitutive law for functionally graded materials (FGM) on the grounds of nonlinear 6-parameter shell theory with the 6th parameter (the drilling degree of freedom) was presented. Here the formulation is extended to the elasto-plastic range. The material law is based on Cosserat plasticity and employs the well-known Tamura-Tomota-Ozawa (TTO) [2] mixture...
-
Stability of an imperfect truss loaded by wind
PublicationThe present paper is devoted to the numerical research of stability of a truss loaded by wind and stiffened by elastic supports located at the top chord. The lateral braces or lateral and torsional braces were taken into account. In this paper, the linear buckling analysis re- sults for the beam and shell model were presented. Two different shapes of initial geometric imperfections were considered in the non-linear static analysis...
-
Nonlinear resultant theory of shells accounting for thermodiffusion
PublicationThe complete nonlinear resultant 2D model of shell thermodiffusion is developed. All 2D balance laws and the entropy imbalance are formulated by direct through-the-thickness integration of respective 3D laws of continuum thermodiffusion. This leads to a more rich thermodynamic structure of our 2D model with several additional 2D fields not present in the 3D parent model. Constitutive equations of elastic thermodiffusive shells...
-
Minimal surfaces and conservation laws for bidimensional structures
PublicationWe discuss conservation laws for thin structures which could be modeled as a material minimal surface, i.e., a surface with zero mean curvatures. The models of an elastic membrane and micropolar (six-parameter) shell undergoing finite deformations are considered. We show that for a minimal surface, it is possible to formulate a conservation law similar to three-dimensional non-linear elasticity. It brings us a path-independent...
-
Transiluminacyjne monitorowanie stanu przestrzeni podpajęczynówkowej
PublicationTransiluminacja tkanek ludzkiego ciała w celach diagnostycznych jest stosowana od ponad stu lat. Metoda transiluminacji w bliskiej podczerwieni z rozpraszaniem zwrotnym (NIRT-BSS) umożliwia ciągłe, bezinwazyjne monitorowanie zmian szerokości przestrzeni podpajęczynówkowej, które może być cennym narzędziem w ocenie zagrożenia obrzękiem mózgu. W rozprawie przedstawiono optyczny model rozchodzenia się promieniowania podczerwonego...
-
Time-domine Dipole Fields in acoustic and Elektromagnetics
PublicationThe ultrawideband (UWB) radio technique presents a challenge not just for technology. The UWB carrier-free pulses act at a close distance, their electromagnetic fields being very different from classic monochromatic plane wave. The author proposes to adapt a time-domian approach to analysis of broadband spherical fields, both acoustic and electromagnetic, in fundamental cases of quasi-point physical sources.
-
MAGNETOACOUSTIC HEATING AND STREAMING IN A PLASMA WITH FINITE ELECTRICAL CONDUCTIVITY
PublicationNonlinear effects of planar and quasi-planar magnetosound perturbations are discussed. Plasma is assumed to be an ideal gas with a finite electrical conductivity permeated by a magnetic filed orthogonal to the trajectories of gas particles. the excitation of non-wave modes in the filed of intense magnetoacoustic perturbations, i.e., magnetoaciustic heating and streaming, is discussed. The analysis includes a derivation if instantaneous...
-
Novel approach to modeling spectral-domain optical coherence tomography with Monte Carlo method
PublicationNumerical modeling Optical Coherence Tomography (OCT) systems is needed for optical setup optimization, development of new signal processing methods and assessment of impact of different physical phenomena inside the sample on OCT signal. The Monte Carlo method has been often used for modeling Optical Coherence Tomography, as it is a well established tool for simulating light propagation in scattering media. However, in this method...
-
Relay-aided Wireless Sensor Network Discovery Algorithm for Dense Industrial IoT utilizing ESPAR Antennas
PublicationIndustrial Internet of Things (IIoT) applicationsrequire reliable and efficient wireless communication. Assumingdense Wireless Sensor Networks (WSNs) operating in a harshenvironment, a concept of a Time Division Multiple Access(TDMA) based WSN enriched with Electronically SteerableParasitic Array Radiator (ESPAR) antennas is proposed andexamined in this work. The utilized...
-
Refinement of the Hardening Soil model within the small strain range
PublicationThe popularity of the elasto-plastic Hardening Soil (HS) model is based on simple parameter identification from standard testing and empirical formulas. The HS model is implemented in many commercial FE codes designed to analyse geotechnical problems. In its basic version, the stress–strain behaviour within the elastic range is subject to the hypoelastic power law, which assures the barotropy of the elastic stiffness. However,...
-
Development of Intelligent Control for Annealing Unit to Ensure the Minimization of Retroactive Effects on the Supply Network
PublicationResearch conducted by our team focused on the development of a complete annealing unit, using modern technologies and components, such as a programmable logic controller, an industrial computer and microcontrollers, ensuring an intelligent way to control power semiconductor elements (SSR relays), with regard to minimizing retroactive effects on the supply network. This modern configuration offers a number of new possibilities of...
-
Zero-pole approach to computer aided design of in-line siw filters with transmission zeros
PublicationThis paper presents a design of a new type of in-line pseudo-elliptic filters implemented in substrate integrated waveguide(SIW) technology. To realize transmission zeros in in-line topology,frequency-dependent couplings were used. Such dispersive couplingswere implemented as shorted stubs. The design process startswith the generation of a suitable starting point. To this end, anapproximation of SIW as a rectangular waveguide is...