Search
Filters
total: 1632
filtered: 1479
displaying 1000 best results Help
Search results for: EXHAUST GAS RECIRCULATION
-
Process Control of Biogas Purification Using Electronic Nose
PublicationNowadays, biogas produced from landfills and wastewater treatment plants or lignocellulosic biomass is important sustainable and affordable source of energy. Impurities from biogas stream can cause a serious odor problem, especially for residents of areas immediately adjacent to production plants. Therefore, biogas pre-treatment is necessary to protect engines that convert biogas into energy and in order to increase the specific...
-
Deep eutectic solvents – based green absorbents for effective volatile organochlorine compounds removal from biogas
PublicationVolatile organochlorine compounds (VOXs) presented in biogas can cause many technological and environmental problems. During the combustion of biogas containing VOXs, the corrosion of installation, as well as the formation of toxic by-products (polyhalogenated dioxins and furans) and further emission to the atmosphere, may occur. Therefore, in this study, a new procedure based on physical absorption was developed. In order to meet...
-
Numerical investigation on distribution characteristics of oxidation air in a lime slurry desulfurization system with rotary jet agitators
PublicationRotary jet agitator is an effective device for mixing, dispersing, dissolving, and suspending dispersed phases in liquid, and is particularly advantageous to the homogenization of oxygen-enriched air within the lime slurry desulfurization system. The distribution of oxygen-enriched air in agitators is vital for the process of gypsum crystallization and the homogeneous and sufficient oxygen-enriched air can promote the formation...
-
In situ study of a composition of outlet gases from biogas fuelled Solid Oxide Fuel Cell performed by the Fourier Transform Infrared Spectroscopy
PublicationThe purpose of this study was to develop a method and software based on the Fourier Transform Infrared Spectroscopy for the in-situ, quantitative analysis of the composition of outlet gases from Solid Oxide Fuel Cell (SOFC). The calibration procedure performed at the beginning of the experiment indicated a polynomial dependence between the concentration of a calibrating gas (CO, CO2, CH4) and the corresponding integrated absorbance in...
-
The potential of LC–MS technique in direct analysis of perfume content
PublicationPerfumes are products that consist of a wide range of natural and synthetic compounds. Due to complex composition, the determination of their ingredients is a difficult task. Most of the perfume components are either volatile or semi-volatile; however, most of the attention has been paid to volatile ones, and thus, gas chromatography or electronic noses are generally used. Nevertheless, in this study, liquid chromatography coupled...
-
The Processing Procedure for the Interpretation of Microseismic Signal Acquired from a Surface Array During Hydraulic Fracturing in Pomerania Region in Poland
PublicationHydraulic fracturing is a procedure of injecting high pressure fluid into the wellbore in order to break shell rock and facilitate gas flow. It is a very costly procedure and, if not conducted properly, it may lead to environmental pollution. To avoid costs associated with pumping fluid outside the perspective (gas rich) zone and improve one’s knowledge about the reservoir rock, microseismic monitoring can be applied. The method...
-
Hysteresis curves for some periodic and aperiodic perturbations in gases
PublicationEvolution of sound in a medium whose properties irreversibly vary in the course of wave propagation, is studied. For example, a gas that is a particular case of a Newtonian fluid is considered. Hysteresis curves, pictorial representations of irreversible attenuation of the sound energy, in the plane of thermodynamic states are plotted. The irreversible losses in internal energy are proportional to the total attenuation and depend...
-
Ring thruster - a preliminary optimisation study of ferrofluid seal and propeller
PublicationThe article reports the course of preliminary examination of a ferrofluid seal applied in liquid environment.A newly built research rig is described, and results of pressure tests performed for different shaft rotationsare discussed. Other studies carried out in the past only referred to the gas environment, while the presentexamination aims at finding an answer to the question whether magnetic liquids can be successfully used...
-
Studies on applicability of new solid-phase microextraction and determination of short - chain monocarboxylic acids
PublicationA convenient approach to monitor the short-chain monocaroboksylic acids (SCAMs) in different samples is gas chromatography (GC) preceded by sample preparation based on solid-phase microextraction (SPME). The fiber with polar coatings were used to extract the SCAMs from headspace of liquid and solid samples. Recently polimeric ionic liquid (PIL) fiber coatings have been proposed to extract volatile organic compounds, minly polar...
-
Skutki zwarć łukowych w średnionapięciowych rozdzielnicach okrętowych z izolacją powietrzną
PublicationW artykule scharakteryzowano moc i napięcie łuku, jak również przedstawiono model termodynamiczny służący do obliczania ciśnienia i temperatury gazów w otoczeniu łuku zwarciowego. Przedstawiono przykładowy układ elektrowni okrętowej i zasilania najważniejszych odbiorników na statku do przewozu kontenerów, w tym 600 kontenerów chłodzonych. Na podstawie parametrów prądnic i silników, odbiorników zasilanych z rozdzielnicy głównej...
-
Mobile Systems (Portable, Handheld, Transportable) for Monitoring Air Pollution
PublicationThe monitoring and analysis of atmospheric air pollutants is a rapidly developing branch of analytical chemistry. The in situ analysis of atmospheric air quality using mobile instrumentation is becoming routine. The article provides information on devices used in various kinds of mobile laboratories. It reviews the portable gas chromatographs and handheld devices used for detecting and determining specific harmful substances in...
-
A LABORATORY STAND FOR THE ANALYSIS OF DYNAMIC PROPERTIES OF THERMOCOUPLES
PublicationIn the present elaboration, problems connected with measurements of high variable temperatures of gases are introduced and the impact of dynamic properties of different construction solutions of thermoelements on the accuracy of the measurements is considered. A laboratory stand built within research under doctoral thesis, destined for analysis of dynamic properties of thermocouples is also described. Results of numerical simulation...
-
ENERGY STORAGE IN COMPRESSED AIR – SOLUTION SUPPORTING RENEWABLE ENERGY SOURCES
PublicationThis article presents a brief description of a power system, the current national power system daily load, the use of wind power as a renewable energy source and its share in the national load. It also discusses the methods for storing energy, their characteristics and possible solutions. The power storage and generation solution proposed in the article is based on the collaboration between a gas turbine and an air storage system....
-
Application of a cellular automaton to simulations of granular flow in silos
PublicationA cellular automaton based on a gas model of hydrodynamics was used to calculate the kinematics of non-cohesive granular materials during confined flow in a mass flow and funnel flow model silo. In the model, collisions of particles were taken into account during granular flow. In addition, a simplified automaton was used wherein granular flow was assumed as an upward propagation of holes through a lattice composed of cells representing...
-
Modeling of entrained flow steam gasification of sewage sludge
PublicationProper management of sewage sludge becomes increasingly problematic due to legal requirements aiming at diminishing environmental impact, as well as rationalizing the utilization from the point of view of logistics. Steam gasification of sewage sludge can result in very good quality of the producer gas. So far, the works have been focused on the gasification in fixed bed gasifiers. However, this does not allow to take full advantage...
-
Recent advances on SOA formation in indoor air, fate and strategies for SOA characterization in indoor air - A review
PublicationRecent studies proves that indoor air chemistry differs in many aspects from atmospheric one. People send up to 90 % of their life indoors being exposed to pollutants present in gas, particle and solid phase. Particle phase indoor is composed of particles emitted from various sources, among which there is an indoor source – secondary chemical reactions leading to formation of secondary organic aerosol (SOA). Lately, researchers'...
-
Helium-assisted, solvent-free electro-activation of 3D printed conductive carbon-polylactide electrodes
PublicationFused filament fabrication is one of the most rapidly developing 3D printing techniques, with numerous applications, including in the field of applied electrochemistry. Here, the utilisation of conductive carbon black polylactic acid (CB-PLA) for 3D printouts is the most promising. To use CB-PLA as an electrode material, an activation process must be performed, removing the polymer matrix and uncovering the electrically conductive...
-
Effect of free water on the quasi‑static compression behavior of partially‑saturated concrete with a fully coupled DEM/CFD approach.
PublicationThe work aims to numerically investigate the quasi-static response of partially fluid-saturated concrete under two-dimensional uniaxial compression at the mesoscale. We investigated how the impact of free pore fluid content (water and gas) affected the quasi-static strength of concrete. The totally and partially fluid-saturated concrete behavior was simulated using an improved pore-scale hydro-mechanical model based on DEM/CFD....
-
Efficiency of Biomass Energy used for Heating Purposes in a Residential Building in Comparison with other Energy Sources
PublicationThis paper discusses the results of analyses investigating the energy efficiency of biomass in comparison with other popular energy carriers used for heating, ventilation and water heating in residential buildings. The compared energy sources were lignite, natural gas, heating oil and electricity produced by conventional and integrated power generation plants. The most efficient variant relying on biomass and the least efficient...
-
Electron impact fragmentation of pyrrole molecules studied by fluorescence emission spectroscopy
PublicationThe fluorescence emission spectroscopy using electron impact excitation technique was employed to study fragmentation processes of the gas phase pyrrole molecules. The following excited fragmentation species were observed by detection of their fluorescence decay: the atomic hydrogen H(n), n = 4-7 and the diatomic CH(A2Δ), CN(B2Σ+), NH(A3Π) and C2(d3Πg) fragments. These atomic and molecular products differ from those previously...
-
Electron energy-loss spectroscopy of excited states of the pyridine molecules
PublicationElectron energy-loss spectra of the pyridine, C5H5N, molecules in the gas phase have been measured to investigate electronic excitation in the energy range 3.5–10 eV. The applied wide range of residual electron energy and the scattering angle range from 10 ◦ to 180 ◦ enabled to differentiate between optically-allowed and -forbidden transitions. These measurements have allowed vertical excitation energies of the triplet excited...
-
Cavitation Erosion of P110 Steel in Different Drilling Muds
PublicationThe P110 steel specimens were subjected to ultrasonic cavitation erosion in different compositions of drilling muds and surfactant additive. The test procedure was based on ASTM-G-32 standard recommendations. API 5CT-P110 steel is used for pipes in oil and gas industry. The harsh environment and high velocity of flows poses corrosive and erosive threat on materials used there. The composition of drilling fluid influences its rheological...
-
State of the art in the field of emission reduction of sulphur dioxide produced during coal combustion
PublicationThe need for clean coal technologies to reduce the adverse environmental impact of coal combustion products has been grounded. The article deals with information concerning present and future technologies, directed towards the struggle against air pollution by SO2, produced during coal combustion. Their classification and critical rating from economical and technological points of views (including those developed by authors) have...
-
Towards high quality ITO coatings: the impact of nitrogen admixture in HiPIMS discharges
PublicationThe paper reports controlled deposition of optically transparent and electrically conductive ITO films prepared by a combination of rf (13.56 MHz) and High Power Impulse Magnetron Sputtering (HiPIMS) systems without any post deposition thermal treatment/annealing. It is shown that (i) reactive admixture of N2 gas to the process and (ii) pressure in the deposition chamber enable to optimize optical properties of ITO films. Furthermore,...
-
Pyrolysis of Waste Biomass: Technical and Process Achievements, and Future Development-A Review
PublicationPyrolysis has been applied in the human economy for many years, and it has become a significant alternative to the production of chemical compounds, including biofuels. The article fo-cuses mostly on recent achievements in the technical and processing aspects of pyrolysis. The aim of the review is to present the latest research on the process of waste biomass pyrolysis to fuel production. The paper describes the mechanisms of...
-
Effect of wet Hydrogen Sulfide on Carbon Steels Degradation in Refinery Based on Case Study
PublicationMaterial degradation caused by wet hydrogen sulfide (Wet H2S) is one of the major issues in refineries. Carbon steel is the main construction material used in refineries and is subjected not only to thickness loss but the hydrogen is the major concern. H2S leads to high atomic hydrogen penetration in steel which causes degradation in the form of blistering and/or cracking (HIC/SOHIC) and stress cracking in the area of welds and...
-
Radioactivity of drilling cuttings from shale resources of the Lower Paleozoic Baltic Basin, Poland
PublicationFractionated drilling wastes originating from shale gas exploration in the Baltic Basin in Pomerania were subjected to the measurements of mean activity concentrations of naturally occurring radioactive materials (NORMs).To better understand rock structure and texture, the X-ray diffraction analysis (XRD) and scanning electron microscopy(SEM) observation were used. To compare activity concentration of radionuclides in bulk wastes...
-
Identification of novel psychoactive substances 25B-NBOMe and 4-CMC in biological material using HPLC-Q-TOF-MS and their quantification in blood using UPLC–MS/MS in case of severe intoxications
PublicationThis paper describes cases of poisoning caused by new psychoactive substances such as: 25BNBOMe (2-(4-bromo-2,5-dimethoxyphenyl)-N-[(2-methoxyphenyl)methyl]ethanamine) and 4-CMC (1-(4-chlorophenyl)-2-(methylamino)-1-propanone). The analytical procedure includes rapid and selective method for the extraction and determination of 4-CMC and 25B-NBOMe in blood samples using UPLC–MS/MS technique. To the best of our knowledge,this is...
-
Thermodynamic interpretation and prediction of CO2 solubility in imidazolium ionic liquids based on regular solution theory
PublicationRegular solution theory (RST) is the most popular model for the interpretation of the interaction between CO2 and ionic liquids. In the present work, the parameters of this model were determined for the CO2 absorption in eleven imidazolium ionic liquids. The y-intercept (A) of the RST model for the investigated imidazolium liquids increases with increasing temperature whereas the slope (B) remains constant. The values of RST parameters...
-
Thermal utilization of meat and bone meals. Performance analysis in terms of drying process, pyrolysis and kinetics of volatiles combustion
PublicationA development of technology of thermal utilization requires a thorough knowledge of the physicochemical properties, as well as kinetics of combustion of volatiles and char. Due to waste management regulations the meat and bone meal (MBM) is regarded as biofuel constituting one of the alternatives to fossil fuels in the energy market. MBM is a heterogeneous material that may consist of several different fractions. The extensive...
-
Analysis of volatile fraction selected hybrid fruits using chromatographic techniques
PublicationAt present, "healthy eating" is gaining in popularity. Many people associate this term with eating plenty of vegetables and fruits. The basic elements influencing the selection of fruit are their appearance and smell. Of course, their origin and impact on human health are also very important. In recent years, exotic fruits have become increasingly accessible, making them gaining popularity, even among Poles. You can also meet plants...
-
Wytwarzanie energii elektrycznej - diagnoza i terapia
PublicationW artykule przeanalizowano stan i dalszy rozwój krajowego sektora wytwarzania energii elektrycznej w świetle najnowszych raportów Międzynarodowej Agencji Energetycznej, wskazujących potencjalne trendy i perspektywy w światowej energetyce. Na tle przewidywanego wzrostu zapotrzebowania na energię elektryczną wskazano na możliwość istotnego ograniczenia emisji CO2 drogą zastąpienia przestarzałych, nieefektywnych...
-
Assessment of fitness for service of Cr-Mo steel tubes in catalytic reforming charge heaters
PublicationIn this paper characteristic features of metal dusting corrosion in high temperature gas mixtures of high carbon activity in catalytic reforming units, including Continuous Catalyst Regeneration (CCR) platformer are presented. Examples of 2.25Cr-1Mo and 9Cr-1Mo steel tubes at advanced stages of metal dusting process after long-term service in charge heaters are used to prove that destructive examinations are necessary to provide...
-
Rational Use of Primary Energy in Single-Family Residential Houses
PublicationThis work presents results of the primary energy use for heating residential single-family house. Analysis includes domestic hot water system (DHW) and heating, ventilation and air condition system (HVAC). During researches the conventional and alternative energy sources (natural gas, biomass, fuel oil, bituminous coal, lignite or electric energy obtained from electric power system – EPS) were used in DHW and HVAC systems. Furthermore...
-
Comparative conformance cases for monitoring multiple implementations of critical requirements
PublicationThe paper presents the concept and the mechanism of comparative conformance cases which support conformance monitoring in situations where a standard or other set of requirements are being implemented at multiple sites. The mechanism is enabled by NOR-STA services which implement the TRUST-IT methodology and are deployed in the cloud in accordance with the SaaS model. In the paper we introduce the concept of comparative conformance...
-
KTaO3-based nanocomposites for air treatment
PublicationThe advantage is that photocatalytic methods allow removing VOCs, NOx, SO2, deodorants, and microorganisms at the same system. The new third generation of photoactive materials activated by low powered and low cost irradiation sources (such as LEDs or black fluorescent UV lamps) can be used as photocatalysts in air purification systems. A series of single semiconductors and their nanocomposites combination were prepared using hydrothermal...
-
Construction and investigation of SO2 amperometric sensor with a solid polymer electrolyte membrane
Publicationn this paper a sensor for detection of the sulphur dioxide based on three electrode cell configuration with a liquid electrolyte, a mercury sulphate reference electrode and a solid polymer electrolyte working electrode is presented. Working elec- trode was obtained by using Takenaka-Torikai chemical deposi- tion method by precipitation of Au particles into the pores of the Nafion membrane. Sensors characteristics measurements were...
-
Analysis of pesticide residue in tomato samples using analytical protocol based on application of QuEChERS technique and GC-ECD system
PublicationQuEChERS sample preparation method was used for the determination of 10 pesticides and their metabolites in tomato samples, coupled to gas chromatography with electron capture detector (GCECD). The experimental parameters including oven temperature program, amount of the sample and purifying agent were optimized. The GC-ECD method was validated in terms of linearity, selectivity and recovery. The limits of detection (LODs) of the...
-
Carbon Dioxide Recovery Skid
PublicationIn the face of tightening climate regulations, the adoption of carbon dioxide recovery systems is inevitable. Modular process skid units have been widely adopted across the industry. The gas-steam power plant skid unit with the carbon dioxide recovery system was described. The proposed skid module consists of the compact cycle with the oxy-combustion and the carbon dioxide capture skid unit producing pure compressed CO2. The compactness...
-
Integrated membrane bioreactors modelling: A review on new comprehensive modelling framework
PublicationIntegrated Membrane Bioreactor (MBR) models, combination of biological and physical models, have been representing powerful tools for the accomplishment of high environmental sustainability. This paper, produced by the International Water Association (IWA) Task Group on Membrane Modelling and Control, reviews the state-of-the-art, identifying gaps for future researches, and proposes a new integrated MBR modelling framework. In...
-
Electron energy-loss spectroscopy of excited states of the diazine molecules: Pyridazine
PublicationExcitation of the valence electronic states of the pyridazine molecules in the gas phase have been studied using the technique of electron energy-loss spectroscopy. Varying the electron scattering conditions, the residual electron energy and scattering angle, enabled the optically-allowed and -forbidden excitations to be differentiated. The measured energy-loss spectra enabled the vertical excitation energies of the observed states...
-
Determinanty bezpieczeństwa energetycznego Mołdawii: między Unią Europejską a Federacją Rosyjską
PublicationArtykuł ukazuje główne determinanty politycznego wymiaru bezpieczeństwa energetycznego Mołdawii wynikające ze stosunków z Unią Europejską i Federacją Rosyjską oraz ewolucji mołdawskiej sceny politycznej. Uwzględniając głównie rosnącą obecność rosyjskiego kapitału na mołdawskim rynku energetycznym od schyłku XX w., narastające zadłużenie za dostawy gazu wobec Gazpromu, rosyjskie szantaże energetyczne i handlowe, stopniowo wprowadzane...
-
Experiments and numerical modeling of meat and bone meal pyrolysis in a rotary kiln
PublicationThe paper presents aspects of modelling the pyrolysis of meat and bone meal (MBM) in a rotary kiln. The pyrolysis of MBM produces a solid fraction which can be used as a fuel, a liquid fraction with potential chemical applications and a low heating value gas. The meat and bone meal pyrolysis was carried out at the temperature of 900 oC. Main features of experiments and numerical model of the pyrolysis were described. The model...
-
Application of Headspace Solid-phase Microextraction with Poly(1-vinyl-3- Hexylimidazolium Chloride) Polymeric Ionic Liquid Coating using GC - MS to Determine Volatile Fatty Acids in Dairy Wastewater
PublicationVolatile fatty acids were determined in this study using headspace solid-phase microextraction (HS-SPME) with a poly(1-vinyl-3-hexylimidazolium chloride) polymeric ionic liquid coated fiber followed by gas chromatography - mass spectrometry. Experimental parameters such as extraction time and temperature, sample volume as well as desorption time and temperature were optimized. Detection limits of the method were in the range of...
-
Determination of Pesticide Residues in Honey using the GC×GC-TOFMS Technique
PublicationIn this study, a QuEChERS method and gas chromatography coupled with time-of-flight mass spectrometry (GCxGC-TOFMS) was developed for rapid extraction and simultaneous determination of 12 pesticide residues in honey. The GCxGC-TOFMS method was validated according to the SANCO guidance in terms of linearity, selectivity, reproducibility and recovery. Regarding the results, recovery rates ranged between 70-120% with relative standard...
-
Ionization and fragmentation of furan molecules by electron collisions
PublicationCation mass spectra obtained by electron impact were measured to investigate the ionization and ionic fragmentation of furan, C4H4O, molecules in the gas phase. The most abundant cations, with comparable intensities in the mass spectra, were the parent, C4H4O+, cation (68 amu) and the C3H3+ fragment (39 amu). The appearance energies of most of the observed ionic fragments were determined and the possible fragmentation processes...
-
Effect of underwater local cavity welding method conditions on diffusible hydrogen content in deposited metal
PublicationOne of the methods with great potential for applications in underwater repairs is local cavity welding. In local cavity method, cooling conditions and diffusible hydrogen amount in weld metal are nearly the same as those existed during welding in the air. This paper presents the results of literature survey and preliminary tests of the effect of local cavity welding conditions on diffusible hydrogen amount in a deposited metal....
-
Ionization and ionic fragmentation of tetrahydrofuran molecules by electron collisions
PublicationElectron impact ionization and ionic fragmentation of tetrahydrofuran molecules in the gas phase were studied in the energy range from ionization threshold up to 150 eV using the technique of mass spectrometry. The cation mass spectra, ionization and ionic fragmentation efficiencies were measured over this energy range. Well-resolved mass peaks were detected in the mass range 10-72 amu and assigned to corresponding ionic molecular...
-
Direct chromatographic methods in the context of green analytical chemistry
PublicationWe review analytical protocols based on gas and liquid chromatography (GC and LC), but involving no sample preparation.Green analytical chemistry seeks to minimize negative impacts of analytical chemistry. Direct analytical methods ideally fulfillthis requirement, as they preclude sample preparation - the most polluting step of the analytical procedure.We describe examples of GC methodologies for environmental and food analysis...
-
Underwater Welding of Duplex Stainless Steel
PublicationThe present work was conducted to assess the weldability of duplex stainless steel at underwater conditions. Interest of underwater welding of this steel grade is connected with necessity of preparing welding repair technologies for subsea pipelines widely used in offshore oil and gas industry. The GMA local cavity welding method was used in the investigations. Welded beads were performed underwater at 0.5 m depth and in the air....