Search
Filters
total: 809
filtered: 685
Search results for: PULSED LASER ABLATION
-
Process Control and Investigation of Oxidation Kinetics of Postoxidative Effluents Using Gas Chromatography with Pulsed Flame Photometric Detection (GC-PFPD)
PublicationThis article presents the results of investigations on the use of headspace analysis and gas chromatography with pulsed flame photometric detection (HSA-GC-PFPD) to evaluate the effectiveness of oxidation of postoxidative effluents from the production of bitumens. Samples of effluents from the bitumen oxidation unit were used in the experiments. In addition, the kinetics of effluent oxidation was also investigated. The content...
-
A Critical Review on Pulsed Electric Field: A Novel Technology for the Extraction of Phytoconstituents
Publication -
Effects of CO2 and Nd:YAG Laser Remelting of the Ti6Al4V Alloy on the Surface Quality and Residual Stresses
PublicationThe titanium alloys are materials susceptible to tribological wear and the laser treatment can be applied in surface treatment processes to obtain for example higher hardness level. From the other side, it is important to take into consideration, that hardness increase that can be connected with cracks . The aim of this research was to investigate the effects of different lasers and the process parameters on the form and level...
-
Effect of Laser Treatment on Intrinsic Mechanical Stresses in Titanium and Some of Its Alloys
PublicationLaser surface treatment conducted at different power levels is an option to modify titanium bone implants to produce nano- and microtopography. However, such processing can lead to excess mechanical stress within the surface layer. This research aims to calculate the level of such residual stresses after the surface processing of Ti grade IV, Ti15Mo, and Ti6Al7Nb alloys with an Nd:YAG laser. Light and scanning electron microscopies...
-
Modelling of the Heat Flux Density Distribution for Laser Beam Welding
PublicationGreat interest of the laser beam welding in industry is a new theoretical task, making planning the welding procedure specification and the quality control of welded joints easier. Estimating and calculating the dimensions of a weld pool and temperature distribution near weld mainly concern heat source modelling. In the presented work calculations of welding pool shape and thermal field for cylindrical-powered-normally model of...
-
Motor bearing diagnostics performed by means of laser vibrometer
PublicationDamage of bearings is the most common cause of failures in squirrel-cage induction motors. That is why the issues connected with diagnostics of bearings are so important. The equipment employed for bearing diagnostics usually makes use of vibrations as the criterion for technical condition of the bearings. This paper presents exemplary results of the research conducted on bearings with artificially introduced damage. A scanning...
-
MARITIME LASER SCANNING AS THE SOURCE FOR SPATIAL DATA
PublicationThe rapid development of scanning technology, especially mobile scanning, gives the possibility to collect spatial data coming from maritime measurement platforms and autonomous manned or unmanned vehicles. Presented solution is derived from the mobile scanning. However we should keep in mind that the specificity of laser scanning at sea and processing collected data should be in the form acceptable in Geographical Information...
-
Airborne and mobile laser scanning in measurements of sea cliffs on the southern Baltic
PublicationMeasurements of sea cliffs performed using periodic surveying based on laser scanning is currently one of the fastest and most accurate solutions. Supported with the technology of satellite measurements using GNSS (Global Navigation Satellite System) positioning and photographic measurements with the use of aerial vehicle, they enable an effective monitoring of the sea cliffs affected by the erosion. In case of the coast of southern...
-
THE METHOD OF ANALYSIS OF DAMAGE REINFORCED CONCRETE BEAMS USING TERRESTRIAL LASER SCANNING
PublicationThe authors present an analysis of the possibility to assess deformations and mode of failure of R-C beams using terrestrial laser scanning. As part of experiments carried out at the Regional Laboratory of Construction (at Gdansk University of Technology), reinforced concrete beams were subjected to destruction by bending and by shear. The process of press impact on the reinforced concrete beam was recorded using terrestrial laser...
-
Influence of the laser remelting parameters on the thickness of surface layers created on the stainless steel X5CrNi18-10
PublicationIn this work the surface of austenitic stainless steel type X5CrNi18-10 was treated by using laser. Laser remelting was done by means of laser MLT 2500 CO2 with different parameters of treatment: P - power beam (800 [W], 1000 [W], 1100 [W], 1200 [W]); v - scanning velocity (6 [mm/s], 7 [mm/s], 8 [mm/s]); diameter of laser beam (1.4 [mm], 1.6 [mm]). The influence of these parameters on the thickness and shape of layers in manufacturing...
-
Laser-assisted approach for improved performance of Au-Ti based glucose sensing electrodes
PublicationThis paper focuses on the synthesis route and electrochemical properties of electrocatalytic material based on gold nanoparticles (NPs) embedded in a structured titanium template obtained via optimized anodization, chemical etching and laser processing. SEM inspection reveals the presence of Au NPs (60–90 nm in diameter) sited in the titanium foil cavities. Performed electrochemical measurements enable nomination of the set of working...
-
Additive manufacturing of Proton-Conducting Ceramics by robocasting with integrated laser postprocessing
PublicationA hybrid system combining robocasting and NIR laser postprocessing has been designed to fabricate layers of mixed proton-electron conducting Ba0.5La0.5Co1-xFexO3-δ ceramic. The proposed manufacturing technique allows for the control of the geometry and microstructure and shortens the fabrication time to a range of a few minutes. Using 5 W laser power and a scanning speed of 500 mm⋅s− 1, sintering of a round-shaped layer with an...
-
STUDIES ON THE USE OF TERRESTRIAL LASER SCANNING IN THE MAINTENANCE OF BUILDINGS BELONGING TO THE CULTURAL HERITAGE
PublicationWithin the frames of the use of terrestrial laser scanning we find numerous examples of registration of building facilities, including also historical and valuable in their culture. In the case presented in this paper, at the root of the problem there is a preservation of the historic blacksmith’s forge located in Gdansk Orunia. The facility dating from the early nineteenth century was intended to repair involving the complete...
-
Studies on the use of terrestrial laser scanning in the maintenance of buildings belonging to the cultural heritage
PublicationWithin the frames of the use of terrestrial laser scanning we find numerous examples of registration of building facilities, including also historical and valuable in their culture. In the case presented in this paper, at the root of the problem there is a preservation of the historic blacksmith's forge located in Gdansk Orunia. The facility dating from the early nineteenth century was intended to repair involving the complete...
-
The method of analysis of damage reinforced concrete beams using terrestial laser scanning
PublicationThe authors present an analysis of the possibility to assess deformations and mechanisms of destructing bent reinforced concrete beams using the terrestrial laser scanning. As part of the experiments carried out at the Regional Laboratory of Construction of the Concrete Structures Division of the Civil and Environmental Engineering Faculty at Gdansk University of Technology, the reinforced concrete beams were subjected to destruction...
-
Effect of selective laser treatment on initiation of fatigue crack in the main part of an undercarriage drag strut
PublicationThis paper presents the results of material characterization and a fatigue test conducted for a laser-re-melted drag strut used in an aircraft landing gear. The drag strut was re-melted with a CO2 laser beam. Eight re-melted paths were made in the form of spiral lines along the axis of the drag strut. Next, the drag strut was subjected to variable loads on a testing machine simulating loads occurring when an aircraft lands. The...
-
Analysis of the applicability of laser scanning to making an inventory of swimming pool facilities
Publication3D scanning can be used in many branches of economy, e.g. reverse and prototype engineering, industrial design, quality control, pros-thetics, orthodontics, archiving of historic objects and archeological findings, examination of a scene of crime, making films and comput-er games. The technology of terrestrial laser scanning has a bright fu-ture as we are living in the time of blooming measurement tech-niques, which can provide...
-
Measurement of the Temporal and Spatial Temperature Distribution on the Surface of PVCP Tissue Phantom Illuminated by Laser Dataset
PublicationThe dataset entitled Measurement of the temporal and spatial temperature distribution on the surface of PVCP tissue phantom illuminated by laser was obtained with a laboratory set-up for characterisation of the thermal properties of optical tissue phantoms during laser irradiation. The dataset contains a single image file representing the spatial temperature distribution on the surface of a PVCP tissue phantom. This thermal image...
-
Effects of Laser Remelting at Cryogenic Conditions on Microstructure and Wear Resistance of the Ti6Al4V Alloy Applied in Medicine
PublicationThe titanium and its alloys can be subjected to surface treatment, including laser treatment. In this work a new laser treatment at cryogenic conditions of Ti6Al4V alloy has been described. The work has been aimed at establishing whether such surface treatment could be suitable for implants working under wear in biological corrosive environment. The remelting has been made with the use of CO2 continuous work laser at laser power...
-
Optimization of the femtosecond laser impulse for excitation and the Spin-Orbit mediated dissociation in the NaRb Dimer
PublicationWe study the dynamics of multiple coupled states under the influence of an arbitrary time-dependent external field to investigate the femtosecond laser-driven excitation and the spin-orbit mediated dissociation in the NaRb dimer. In this process, the dimer is excited from the ground triplet state 1^3Sigma+ to the 1^3Pi state using the femtosecond laser impulse and the spin-orbit coupling between the 1^3Pi and 2^1Sigma+ states results...
-
Two-photon perimetry utilizing picosecond laser
PublicationAge-related impairments are becoming more and more severe for aging societies. The sensory organ diseases are particularly troublesome as they exclude seniors from their everyday activity. Therefore, maintaining good quality eyesight is essential for normal functioning. New medical therapies help restrain age-related changes, but still, monitoring is essential to the treatment process. Humans do not have the natural ability to...
-
Anodic titania nanotubes decorated with gold nanoparticles produced by laser-induced dewetting of thin metallic films
PublicationHerein, we combine titania layers with gold species in a laser-supported process and report a substantial change of properties of the resulting heterostructures depending on the major processing parameters. Electrodes were fabricated via an anodisation process complemented with calcination to ensure a crystalline phase, and followed by magnetron sputtering of metallic films. The obtained TiO2 nanotubes with deposited thin (5, 10...
-
Prosthetic Elements Made of the Ti-13Zr-13Nb Alloy by Selective Laser Melting
PublicationThe fabrication of the prosthetic foundations and bridges from the Ti-13Zr-13Nb alloy is described. The process was started from CAD/CAM design of 3D models of the foundations based on scanning of patient`s mouth. Next, 3D models were transformed into *.stl files for the manufacturing stage and then the manufacturing process by means of the selective laser melting with the SLM Realizer 100 equipment was made. The intrinsic structure...
-
Combined Close Range Photogrammetry and Terrestrial Laser Scanning for Ship Hull Modelling
PublicationThe paper addresses the fields of combined close-range photogrammetry and terrestrial laser scanning in the light of ship modelling. The authors pointed out precision and measurement accuracy due to their possible complex application for ship hulls inventories. Due to prescribed vitality of every ship structure, it is crucial to prepare documentation to support the vessel processes. The presented methods are directed, combined...
-
Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel
PublicationCommercially available austenic stainless steel substrate was coated with commercially available, raw Al2O3 powder applied by means of plasma spraying method and then re-melted with CO2 laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser...
-
Influence of laser processing of the low alloy medium carbon structural steel on the development of the fatigue crack
PublicationThe paper contains the results of the structural analysis, hardness tests and fatigue tests conducted for the medium carbon structural steel with low content of Cr and Ni after its processing with CO2 laser beam. Pre-cracks were made in the round compact tension (RCT) specimen used for fatigue test. Next, four paths, parallel to each other, were melted on both sides of the samples using a laser beam. The paths were perpendicular...
-
Mechanical Properties and Wear Susceptibility Determined by Nanoindentation Technique of Ti13Nb13Zr Titanium Alloy after “Direct Laser Writing”
PublicationLaser treatment has often been applied to rebuild the surface layer of titanium and its alloys destined for long-term implants. Such treatment has always been associated with forming melted and re-solidified thin surface layers. The process parameters of such laser treatment can be different, including the patterning of a surface by so-called direct writing. In this research, pulse laser treatment was performed on the Ti13Nb13Zr...
-
THE METHOD OF MEASURING THE MEMBRANE COVER GEOMETRY USING LASER SCANNING AND SYNCHRONOUS PHOTOGRAMMETRY
PublicationThe authors present the experience and results of field studies carried out at the technical acceptance of Forest Opera (name in Polish: Opera Leśna) in Sopot (Poland). An unusual design of covering made in the form of “Sheerfill I” technical fabric membrane required spanned in the form of sails, required the use of terrestrial laser scanning. Such approach allowed for the fast and accurate record of the surface of individual panels...
-
Modes of Failure Analysis in Reinforced Concrete Beam Using Laser Scanning and Synchro-Photogrammetry
PublicationThe following paper reveal the limitations and possibilities of terrestrial laser scanning technology adaptation in diagnostics of reinforced concrete beams. In this paper, authors present potential spectrum of TLS use in modes of failure analysis of R-C beams and determines under which conditions the laser technologies might be applied. Research was carried out at the Regional Laboratory of Structural Engineering at Gdansk University...
-
Laser Beam as a Precision Tool to Increase Fatigue Resistance in an Eyelet of Undercarriage Drag Strut
PublicationThe article contains the results of tests on a laser-processed eyelet of undercarriage drag strut to increase its fatigue strength. Laser processing concentrated on both sides around the hole of eye for connecting the undercarriage drag strut caused that the material in this area withstood more than twice the number of load cycles established for this material. In order to determine the reasons for the increase in fatigue strength,...
-
Advancements in the Additive Manufacturing of Magnesium and Aluminum Alloys through Laser-Based Approach
PublicationComplex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives such as reduced part numbers, greater functionality, and lightweight, among others. Polymers, metals, and ceramics are the few materials that can be used in AM technology, but metallic materials (Magnesium and Aluminum) are attracting more attention from the research and industrial point of view. Understanding the role...
-
Laser technology 2012
Publication -
Wear Resistance Enhancement of Al6061 Alloy Surface Layer by Laser Dispersed Carbide Powders
PublicationIn this paper, results of the experimental study on improving wear resistance in sliding friction of Al-based alloy are presented. The technique used involves the formation of a metal matrix composite (MMC) in the alloy surface layer by laser dispersion of carbide powders such as WC, TiC and SiC. For WC and TiC MMC surface coatings fabricated under conditions typical for most of the technologically relevant solid-state lasers (wavelength...
-
Problems of analysis of axially loaded steel behavior under laser welded panel
PublicationWprowadzanie do praktyki nowych rozwiązań konstrukcyjnych wymaga posiadania danych wejściowych do procesu modelowania ich zachowania. Takim nowym elementem jest stalowy, spawany laserowo panel typu sandwich. W pracy pokazano wy-brane problemy towarzyszące modelowaniu zachowań takiej struktury. Pokazano podstawy teoretyczne wyznaczania sztyw-ności panelu a następnie omówiono wyniki badań wyboczenio-wych serii modeli o zmiennej geometrii.
-
Determinants of the surface quality, density and dimensional correctness in selective laser melting of the Ti-13Zr-13Nb alloy
PublicationSelective laser melting is widely used for custom-designed elements. Successful manufacturing depends on laser treatment parameters and material features. This research aimed to determine the effects of laser power, scan time and hatch distance on surface quality, relative density and dimensional precision for cuboids made of the Ti-13Zr-13Nb alloy. The influence of energy density, energy flux and pre-heating was seen to be decisive...
-
Determination of cyanide ion in urine samples using ion chromatography with pulsed amperometric detection.
PublicationCyanides are widely applied in industrial activity, including gold and silver mining and the production of organic chemicals. HCN is also formed directly from fossil fuel combustion sources from gasoline and diesel vehicles. In natural environment, in plants seeds for example an apple seed, it exists as a cyanogenic glycosides. The amount of cyanide ions originating from food products is however rather small. Larger concentrations...
-
BACTERIAL INACTIVATION VIA LASER-DRIVEN GOLD NANOPARTICLE HEATING: SIMULATION AND ANALYSIS
PublicationThis study utilizes CFD technique to simulate the inactivation of E. coli bacteria within a microfluidic chamber, employing gold nanoparticles irradiated by a laser beam. Employing a single-phase model, the presence of bacteria is considered by treating thermal properties in the governing equations as effective, combining those of water and bacteria using established correlations from scientific literature. The conversion of light...
-
Heat Transfer of the Multicolor-Laser-Sources-Irradiated Nanoparticles in Reference to Thermal Processes
PublicationUnlike the standard materials, metallic nanoparticles offer enhancing the heat convertion rate which implies the maximum and average temperature boost significantly in the considered system. The work’s purpose is to examine heat transfer in the metallic nanoparticles which have been deposited on a glassy substrate, enabling the nanostructures thermoablation. Furthermore, the functionalized substrate is irradiated with multicolor-laser-sources,...
-
Laser stimulated second and third harmonic optical effects in F: SnO2 nanostructures grown via chemical synthetic route
Publication -
The effect of laser on metal surfaces for multidisciplinary usage in material and thermal engineering
PublicationThe subject of heat transfer and cooling systems is still a matter of contention in many different fields of science and industry. Infrigidation is much more difficult than warming, and so, much more needed in more and more different devices, starting from massive industrial machinery and air conditioning in commercial buildings, up to micro and nano-surgery tools. In fact, the size of many cooling systems is still a problem. It...
-
The phase composition of the surface layer of laser melted Ti-6Al-4V bioalloy
PublicationZastosowanie metody obróbki laserowej stopów Ti zwiekszyły twardość i odporność stopu na korozję. Jednakże uzyskane warstwy były stosunkowo cieńkie. W pracy zastosowano laser o dużej mocy dla stopu schłodzonego w ciekłym azocie, aby uzyskać grubszą warstwę, która w strefie zewnętrznej złożona będzie z tlenku i azotku tytanu, ważnych faz w biostopach.
-
Analysis of the Surface Stereometry of Alloyed Austenitic Steel after Fibre Laser Cutting using Confocal Microscopy
PublicationThe paper extends the concept of cut edge quality and examines the fibre laser cutting process. A Prima Power Platino Fiber Evo device with a reference speed (RS) of 3500 mm/min was used for laser cutting. In order to analyse the influence of the laser cutting speed on the cut edge quality of X5CrNi18-10 stainless steel sheets, macroscopic studies were conducted on a stereoscopic microscope and surface stereometry on a confocal...
-
Effect of pulse laser treatment at different process variables on mechanical behavior of carbon nanotubes electrophoretically deposited on titanium alloy
PublicationPurpose: Titanium and its alloys are widely used as biomaterials for long-term implants, but they are usually surface-modified due to their weak bioactivity and wear resistance. Laser processing was used to modify the surface layer, and elemental carbon was a component of the deposited coatings. This research aims to use a combination of both methods based on preliminary electrophoretic deposition of multi-wall carbon nanotubes...
-
Review of Shoreline Extraction Methods from Aerial Laser Scanning
PublicationAutonomous technologies are increasingly used in various areas of science. The use of unmanned vehicles for hydrographic surveys in shallow coastal areas requires accurate estimation of shoreline position. This is a nontrivial task, which can be performed using a wide range of sensors and methods. The aim of the publication is to review shoreline extraction methods based solely on data from aerial laser scanning (ALS). This narrative...
-
Experimental Evaluation of ND: YAG Laser Parameters and Sample Preparation Methods for Texturing Thin AISI 316L Steel Samples
PublicationIn mechanical and material engineering, the effect of laser texturing depends on many factors besides device specification, primarily the properties of the materials being processed, and, secondly, the preparation of the sample. Laser texturing of thin (<5 mm) samples is mostly performed utilizing short-pulse lasers, but depending on the power of the laser beam, the process can also be performed by using continuous operation lasers....
-
A new approach of coastal cliff monitoring using Mobile Laser Scanning
PublicationThe article proposes a new approach of coastal cliff monitoring which bases on a new comprehensive monitoring system, being a combination of mobile scanning from the sea with the geotechnical stability analysis. Mobile laser scanning is an innovative solution for 3D data collection which allows the monitored object geometry to be precisely measured, thus providing opportunities for series of analyses contributing to the development...
-
APPLYING RANSAC ALGORITHM FOR FITTING SCANNING STRIPS FROM AIRBORNE LASER SCANNING
PublicationDuring the development of the data acquired by airborne laser scanning the important issue is the fitting and georeferencing of ALS point clouds by means of the tie surfaces and the reference planes. The process of scanning strips adjustment is based on mutual integration of point clouds (scanning strips) and their adaptation to the reference planes.In simultaneous adjustment all strips are combined into one geometrically coherent...
-
Model of optical phantoms thermal response upon irradiation with 975 nm dermatological laser
PublicationWe have developed a numerical model describing the optical and thermal behavior of optical tissue phantoms upon laser irradiation. According to our previous studies, the phantoms can be used as substitute of real skin from the optical, as well as thermal point of view. However, the thermal parameters are not entirely similar to those of real tissues thus there is a need to develop mathematical model, describing the thermal and...
-
Kinetics of molecular decomposition under irradiation of gold nanoparticles with nanosecond laser pulses—A 5-Bromouracil case study
PublicationABSTRACT Laser illuminated gold nanoparticles (AuNPs) efficiently absorb light and heat up the surrounding medium, leading to versatile applications ranging from plasmonic catalysis to cancer photothermal therapy. Therefore, an in-depth understanding of the thermal, optical, and electron induced reaction pathways is required. Here, the electrophilic DNA nucleobase analog 5-Bromouracil (BrU) has been used as a model compound to...
-
Impact of laser beam welding on mechanical behaviour of 2.25Cr–1Mo (P22) steel
PublicationThe use of welding processes in the manufacturing and repair of structures intended for the energy industry plays a key role in the guarantee of a continuous supply of fossil fuels, which is the basic condition for ensuring energy security. A square butt joint of 10 mm thick plate of 2.25Cr–1Mo (P22) steel was fabricated by autogenous laser beam welding process and then post-weld heat treatment (PWHT) for two sets of process parameters...