displaying 1000 best results Help
Search results for: ABRASIVE WEAR RESISTANCE
-
Synthesis and biological evaluation of 2,7-Dihydro-3H-dibenzo[de,h]cinnoli- ne-3,7-done derivatives a novel group of anticancer agents active on a multidrug resistance cell line.
PublicationZsyntezowano serię pochodnych pirydazonu z jednym lub dwoma łańcuchami bocznymi w różnych pozycjach chromoforu tetracyklicznego. Związki wykazały aktywność cytoksyczną na mysią białaczkę L1210 i ludzką k562 oraz na linii komórkowej oporności krzyżowej MDR (k562/DX). Dwa najbardziej aktywne związki przetestowano in vivo na mysiej białaczce P388. Wykazały one aktywność przeciwnowotworową porównywalną z aktywnością Mitoxantronu.
-
The Effect of Sodium Tetrafluoroborate on the Properties of Conversion Coatings Formed on the AZ91D Magnesium Alloy by Plasma Electrolytic Oxidation
PublicationMagnesium and its alloys are widely used in many areas because of their light weight, excellent dimensional stability, and high strength-to-weight ratio. However, the material exhibits poor wear and corrosion resistance, which limits its use. Plasma electrolytic oxidation (PEO) is an effective surface modification method for producing ceramic oxide layers on Mg and their alloys. The influence of the additions of sodium tetrafluoroborate...
-
Research on Tool Temperature Dependence on Lapping Grains Size
PublicationCommonly used as a finishing operation, lapping has been used for achieving ultra-high finishes and close tolerances between mating pieces. Its carried out by applying loose abrasive grains between work and lap surfaces, and causing a relative motion between them resulting in a finish of multi-directional lay. The grains activity (sliding and rolling) in the working gap causes not only the material removal but also the temperature...
-
Wear in siding friction tests. Ring-on-ring contact. Sintered alumina ceramics (98%). Paraffin oil lubrication. Specim. sets #20-#21, #22-#23, #24-#25, #26-#27, #28-#29,#30 - #31. Run time: 0-4h. High frequency burst recording.
Open Research DataWear in sliding friction tests in ring-on-ring contact. Sintered alumina ceramics (98%) in self-mated contact. Lubrication: paraffin oil. Sliding velocity: 0.2 m/s. Mean contact stress: 10 MPa. Test rig: PT-3 Tribometer. High frequency burst recording.Running time: 0 - 4h.Specimen sets:Specim. sets (# [upper, rotating] - #[lower, non-rotating]):#20-#21,...
-
Michał Ryms dr inż.
PeopleMichał Ryms, PhD, Eng. is the physicist, graduate of the Gdańsk University of Technology. PhD thesis defended at the Chemical Faculty. Since 2011 an employee at the Department of Chemical Apparatus and Theory of Machines, Chemical Faculty, Gdansk University of Technology, POLAND – now as an assistant professor. His research interests includes: improvement of energy efficiency and possibilities of new application of phase change...
-
Exsolution of Ni nanoparticles on the surface of cerium and nickel co-doped lanthanum strontium titanate as a new anodic layer for DIR-SOFC. Anti-coking potential and H2S poisoning resistance of the prepared material
PublicationThe aim of this study was to evaluate a new catalytic material for biogas fueled DIR-SOFC. This material was a perovskite-type SrTiO3 doped with La, Ce and Ni of a general formula La0.27Sr0.54Ce0.09Ni0.1Ti0.9O3-σ (LSCNT). Additional preparation steps were undertaken to promote a nickel exsolution process. Heat post-treatment of powders in a humidified H2 resulted in an intensive growth of nickel nanoparticles (NPs) while the temperature...
-
Developments in manufacturing engineering and machining process planning
PublicationCurrent research conducted in the Department of Manufacturing Engineering and Automation is presented in the paper. This includes: abrasive cutting off, grinding with lapping kinematics, rapid prototyping and machining procrss planning. Experimental results and computer simulation are presented and analysed.
-
Mechanical Behavior of Bi-Layer and Dispersion Coatings Composed of Several Nanostructures on Ti13Nb13Zr Alloy
PublicationTitanium implants are commonly used because of several advantages, but their surface modification is necessary to enhance bioactivity. Recently, their surface coatings were developed to induce local antibacterial properties. The aim of this research was to investigate and compare me-chanical properties of three coatings: multi-wall carbon nanotubes (MWCNTs), bi-layer composed of an inner MWCNTs layer and an outer TiO2 layer, and...
-
Curve Curvature Analysis of a Grain Trajectories in Variable Honing of Cylindrical Holes of Thin Wall Cylinder Liners as a Honing Process Optimization Strategy
PublicationThe main problem of honing of thin wall cylinder liners is a thermal distortion of honed holes. The higher the value of the temperature of the honed workpiece, the greater its holes deformation. The paper presents a method of reducing the temperature occurring in the honing process as a result of the application of a variable honing kinematics conditions with particular emphasis on the analysis of the effect of the value of the...
-
The antimicrobial resistance of the Enterobacteriaceae family bacteria isolated from harbour water sediments in the Northern Poland = Lekooporność bakterii z rodziny Enterobacteriaceae wyizolowanych z portowych osadów dennych w Polsce Północnej
PublicationPraca dotyczy oceny lekooporności bakterii z rodziny Enterobacteriaceae wyizolowanych z dennych osadów portowych pobranych w dwóch polskich morskich portach w Gdańsku i w Gdyni.
-
Anna Brillowska-Dąbrowska dr hab. inż.
PeopleAnna Brillowska-Dąbrowska, born in 1971 in Gdańsk, Poland, graduated in 1996 in Biotechnology from the Faculty of Chemistry, Gdańsk University of Technology (GUT). In 2001 she got her PhD, in 2013 became a DSc (habilitation). She was employed in 2004 as a researcher in Statens Serum Institut in Denmark. Currently she is an Associate Professor (adiunkt) in the Department of Molecular Biotechnology and Microbiology and Vice-dean...
-
Dawid Zieliński dr inż.
PeopleDawid Zieliński uzyskał tytuł magistra inżyniera w 2017 roku na Wydziale Mechanicznych Politechniki Gdańskiej, kończąc kierunek: Mechanika i Budowa Maszyn, specjalność: Technologia Maszyn i Komputerowe Wspomaganie Produkcji. W okresie 2016-17 studiował na Uniwersytecie Technicznym w Berlinie (Technische Universität Berlin – TU Berlin) oraz pracował w instytucie naukowym – Institut für Werkzeugmaschinen und Fabrikbetrieb (IWF) Technische...
-
Focused ion beam-based microfabrication of boron-doped diamond single-crystal tip cantilevers for electrical and mechanical scanning probe microscopy
PublicationIn this paper, the fabrication process and electromechanical properties of novel atomic force microscopy probes utilising single-crystal boron-doped diamond are presented. The developed probes integrate scanning tips made of chemical vapour deposition-grown, freestanding diamond foil. The fabrication procedure was performed using nanomanipulation techniques combined with scanning electron microscopy and focused ion beam technologies....
-
Technological Problems in Lapping on Flat Surfaces of Ceramic Parts
PublicationThis paper will present the results of research on single-disc lapping of flat surfaces of small ceramic elements. Machining with the use of different tools such as metallic, two-metallic and abrasive-metallic will be analyzed. The basics and techniques of reinforcement of laps will be discussed. The results of the influence of parameters on the surface quality of ceramic conponents (sealing) for three treatments on lapping machines...
-
Phylogenetic relationship and antimicrobial resistance in Escherichia coli isolated from the Reda River and the Oliwski Stream, Northern Poland = Lekooporność i przynależność filogenetyczna szczepów Escherichia Coli izolowanych z rzeki Redy i Potoku Oliwskiego
PublicationThe high abundance of fecal bacteria in surface water is usually related to poor agricultural practice, pollution caused by domesticated and wild animals as well as with septic tank failures. Identification of fecal contamination sources seems to be crucial in order to effectively estimate the inherent risk. In this study, the phylogenetic relationship of 30 isolates of E. coli, originated from surface water, was estimated by employing...
-
Ryszard Woźniak dr inż.
PeopleRyszard Woźniak received his M.Sc. (1984) from the Lublin University of Technology specializing in Cars and Tractors. In 2002, at the Gdansk University of Technology he defended his doctoral thesis on: "Tyre/road noise when large longitudinal forces are applied in tyre/road contact patch" and obtained a doctorate degree in technical sciences in the field of construction and operation of machines. Currently he is an adjunct at the...
-
Peculiarities associated with testing polyetheretherketone (PEEK) in a model rolling contact
PublicationPolyetheretherketone (PEEK) was investigated using a modified version of the four-ball tester in which the upper forth ball was replaced by a cone in such a way that kinematics of the four-ball configuration were fully preserved. Rotation of the cone enforced orbiting and rolling of the ceramic balls around the polymer cup. The results produced some unexpected peculiarities in the wear of ceramic balls which, in principle, should...
-
Measurement of the tram rail profile during a year of operation - supplementary data
Open Research DataThe aim of the work was to analyze the wear of rails during operation and to analyze the supplementation of heavy metals in the soil around the tram route, originating from wearing out rails and tram wheels.The dataset contains measurements of rail head coordinates in 9 research sections made in 8 measurement series. The wear of the rails in selected...
-
<p>Potential effects of microbial air quality on the number of new cases of diabetes type 1 in children in two regions of Poland: a pilot study</p>
Publication -
Preliminary Study on the Antibacterial Activity of Essential Oils Alone and in Combination with Gentamicin Against Extended-Spectrum β-Lactamase-Producing and New Delhi Metallo-β-Lactamase-1-Producing Klebsiella pneumoniae Isolates
Publication -
Bacteriophage–Ciprofloxacin Combination Effectiveness Depends on Staphylococcus aureus–Candida albicans Dual-Species Communities’ Growth Model
Publication -
Biofilm Formation and Prevalence of Biofilm-Related Genes Among Clinical Strains of Multidrug-Resistant Staphylococcus aureus
Publication -
Environmental Phage-Based Cocktail and Antibiotic Combination Effects onAcinetobacter baumanniiBiofilm in a Human Urine Model
Publication -
The Effect of Subinhibitory Concentrations of trans-Anethole on Antibacterial and Antibiofilm Activity of Mupirocin Against Mupirocin-Resistant Staphylococcus aureus Strains
Publication -
Structural and electronic properties of diamond-composed heterostructures
PublicationDiamond is a promising material for 21st century electronics due to its high thermal and electronic conductivity, biocompatibility, chemical stability, high wear resistance, and possibility of doping. However, the semiconductor properties of diamond, especially free-standing films, have not been fully explored. Nor have their integration with polymers and fragile materials and their applications as electronic components. In this...
-
Impact of low-temperature sintering on the Fe-based amorphous coatings
PublicationBulk metallic glasses (BMGs) have gained a lot of attention in recent years due to their outstanding properties such as high hardness and excellent wear and corrosion resistance. However, they are restricted in industrial applications due to their extreme brittleness. Iron based amorphous coatings from BMGs are the best solution to use them by overcoming the problem of extreme brittleness. The coatings can be sprayed by various...
-
A Multi Rig Screening Test for Thin Ceramic Coatings in Bio - Tribological Applications
PublicationA method is presented for the comparative testing of wear resistance of ceramic coatings made from materials potentially feasible in tribo - medical applications, mainly orthopaedic implants made from ceramics coated metals for low cost, long life and low wear particle emission into the body. The method was devised as the main tool for use in research and is comprised of flat on flat and ball on flat surface (sliding) tests. Seven...
-
3D Machine Vision System for Inspection of Contact Strips in Railway Vehicle Current Collectors
PublicationConstruction and technical condition of current collectors is crucial to reliability and safety of railway transportation. According to the Technical Specifications for Interoperability railway vehicles in the European Union should be equipped with carbon contact strips. Excessive wear or defects of contact strips degrade the capability of undisturbed power transmission, cause faster wear of contact wire, and can even result in...
-
Statistics of AFM current-voltage curves
Open Research DataMapping surface electrical conductivity offers enormous cognitive possibilities regarding the structure and properties of modern materials. The technique invented for this purpose (Conductive AFM) by Murrel's team and colleagues allows independent monitoring of the local conductivity of materials in correlation with the topographic profile. The mentioned...
-
Preparation to ball on disk test Initial contact stress evaluation
Open Research DataEvaluation of initial contact stress in tests on wear of Al6061 alloy in ball on disk tribological testing. Research on the reinforcing effect of aluminium alloy injection reinforcement with TiN and WC powders in laser remelted surface layer.
-
Measurement of the tram rail profile during a year of operation
Open Research DataThe aim of the work was to analyze the wear of rails during operation and to analyze the supplementation of heavy metals in the soil around the tram route, originating from wearing out rails and tram wheels.The dataset contains measurements of rail head coordinates in 9 research sections made in 8 measurement series. The wear of the rails in selected...
-
Wpływ przechyłki na zjawisko postępowania zużycia bocznego szyn kolejowych w łukach poziomych
PublicationDegradacja elementów nawierzchni kolejowej jest zagadnieniem bardzo złożonym, w które uwikłane jest wiele czynników związanych między innymi z układem geometrycznym toru kolejowego, właściwościami trybologicznymi poszczególnych elementów nawierzchni, jak również z parametrami podłoża gruntowego, a także z właściwościami samych pojazdów szynowych. W artykule omówiono jeden z powyższych problemów, tj. wpływ ukształtowania toru kolejowego...
-
Reinforced aluminium reference measurement R63 – earlier tests
Open Research DataPreliminary testing of aluminium alloys against 100Cr6 steel ball. Preparation to tests on wear of Al6061 alloy in ball on disk experiment. Research on the reinforcing effect of aluminium alloy injection reinforcement with TiN and WC powders in laser remelted surface layer.
-
Reinforced aluminium reference measurement Result1 – earlier tests
Open Research DataPreliminary testing of aluminium alloys against 100Cr6 steel ball. Preparation to tests on wear of Al6061 alloy in ball on disk experiment. Research on the reinforcing effect of aluminium alloy injection reinforcement with TiN and WC powders in laser remelted surface layer.
-
Reliability model of the crankshaft-piston assembly
PublicationThe laws that govern the durability of crankshaft-piston assembly friction nodes can be proved or at least derived or justified in an intuitive way. Operation of all the friction nodes is disturbed by external factors occurring with randomly changing intensity and also appearing at random. As the crankshaft-piston assembly friction nodes have a series structure and effects of those disturbances accumulate, their fitness for use...
-
Polymer journal bearings behaviour research under limited lubrication and cooling conditions conducted on high torque test rig
PublicationPolymer journal bearings are frequently used as a water-lubricated bearings of small marine units’ propeller shafts . Choice of these bearings is based on their simple construction and relatively low purchase and maintenance costs. Although properly designed and installed water lubricated bearings may well last for over a decade, rapid wear or failure of these bearings can be observed...
-
Roller burnishing
PublicationThe paper shows the process of roller burnishing as a method of finishing machine components. Based on own research the author presents the effects of the roller burnishing process to increase the hardness and residual stress as well as the wear and fatigue strength of burnishing components.
-
Formation of Porous Structure of the Metallic Materials Used on Bone Implants
PublicationResearch on improvement of structure and fabrication methods of the bone implants are carried out for many years. Research are aimed to shape the structures, that will have a Young's modulus value similar to the value of the human bones Young's modulus. Depending on theporosity, Young's moduli can even be tailored to match the modulus of bone closer than solid metals can, thus reducing the problems associated with stress shielding...
-
Ocena odporności powłok na bazie DLC na doraźne uszkodzenie w warunkach tarcia ślizgowego ze smarowaniem wodą i solą fizjologiczną = Evaluation of DLC based coatings resistance to instanteneous damage under sliding friction conditions with distilated water or saline lubrication
PublicationWykonano serię testów w celu wyznaczenia granicznych warunków wymuszenia, zdefiniowaego jako średnie naciski powierzchniowe oraz prędkość ślizgania, po przekroczeniu których następuje gwałtowne zniszczenie powłoki. Na podstawie wyników pomiarów opracowano aproksymowane charakterystyki granicznych wymuszeń w układzie p - v oraz pokrewnych dla badanych materiałów, smarów i zakresu parametrów wymuszenia.
-
The Influence of External Load on the Performance of Microbial Fuel Cells
PublicationIn this work, the effect of the external load on the current and power generation, as well as on the pollutant removal by microbial fuel cells (MFCs), has been studied by step-wise modifying the external load. The load changes included a direct scan, in which the external resistance was increased from 120 Ω to 3300 Ω, and a subsequent reverse scan, in which the external resistance was decreased back to 120 Ω. The reduction in the...
-
The Effect of Cryogenic Treatment on Microstructure and Mechanical Response of AISI D3 Tool Steel Punches
PublicationRecently, deep cryogenic treatment is performed to improve the mechanical responses (wear, hardness, fatigue, and thermal conductivity) of various steel components. Researchers have tried to evaluate the eco-friendly and nontoxic process to optimize the parameters. Cold-shearing punches used to manufacture various holes that undergo severe impact loading and wear in the metal forming process. This study concerns the effect of soaking...
-
Influence of operating pressure on the durability of a satellite hydraulic motor supplied by rapeseed oil
PublicationThis article describes the results of a durability test of a hydraulic satellite motor supplied by rapeseed oil. The tests were carried out on a test stand in a power recuperation system. The tests of the motor were carried out at a constant shaft speed for three fixed pressure drops in the motor. This made it possible to demonstrate the influence of the motor operating pressure on the durability of the satellite mechanism. The...
-
Profile irregularities of turned surfaces as a result of machine tool interactions
PublicationThe paper describes the influence of the machining operation on a surface, which disturbs the projection of the tool profile in the form of its relative movements with respect to the object. The elements of the machine tool undergo constant wear during the machining process, it is therefore important to recognize the effects of their influence on the surface's irregularities. Amplitude-frequency analysis of lateral profiles has...
-
OVERALL SET OF BANDSAW TEETH VERSUS METHODS OF MEASUREMENTS
PublicationThis article deals with the impact of the manual methods of measurement on the overall set measurement results. It describes the results of the measurement of bandsaw teeth kerf with the use of a micrometer and a digital calliper. It is commonly known that the cutting process causes the wear of cutting tools. The wear of the cutting edge depends on the cutting conditions as well as on the mechanical properties of the processed...
-
Effect of presence of lifting pocket on the THD performance of a large tilting-pad thrust bearing
PublicationHydrostatic assistance is a commonly used method to improve limited load carrying ability of tiltingpad thrust bearings during transient states of operation of vertical shaft hydro-generators. Despite of special hydraulic equipment (as pumps, valves, etc.), it also requires manufacturing of special recesses/pockets at pad sliding surfaces, into which oil is injected under high pressure. It allows to lift the rotor before start-up...
-
Research on water lubricated main shaft bearings in conditions of improper lubrication and cooling conducted on high torque real-life scale bush test rig
PublicationWater lubricated polymer bushes find increasingly popular use in the sliding bearings of marine propellers, water turbines and pump shafts. Such popularity is partly due to their simple construction which also means relatively affordable price. In addition, properly designed and installed water lubricated bearings may well last for over a decade. However, in practical experience one may also observe cases of rapid wear...
-
Laser Welding of UNS S33207 Hyper-Duplex Stainless Steel to 6061 Aluminum Alloy Using High Entropy Alloy as a Filler Material
PublicationThe high entropy alloy (HEA) filler used during the fabrication method determines the reliability of HEAs for steel-aluminum dissimilar alloy configuration. HEAs have a direct impact on the formation of intermetallic compounds (IMC) formed by the interaction of iron (Fe) and aluminum (Al), and influence the size of the joint’s interaction zone. A novel welding process for Fe-Al alloy joints was developed to prevent the development...
-
Jerzy H. Czembor Prof. dr hab.
PeopleYear of birth: 1965, Poland, Work address: Plant Breeding and Acclimatization Institute –National research Institute (IHAR-PIB), Radzikow, 05-870 Blonie, Poland. Scientific disciplines: agricultural sciences, plant pathology, plant physiology, genetics. Specialization: phytopathology, mycology, plant genetics, molecular genetics, plant breeding, breeding for disease resistance, biotechnology, evaluation of genetic resources,...
-
The effectivness of fault detection in common rail injectors examination methods
PublicationThe article presents the effectiveness tests of fault detection in common rail injectors. 40 injectors with different wear levels were tested. Testing was made on two test benches of a completely different design. Research includes comparison of accuracy, reproducibility and testability to detect specific defects. A device was created for visualization of the fuel injector spraying steam.
-
Beata Krawczyk dr hab.
PeopleBeata Krawczyk, PhD, Professor Academic degrees, education, qualifications: B. Krawczyk earned his master degree in Biology at the University of Gdansk, Biology Faculty, in 1986, and her PhD in Molecular Biology at the University of Gdansk, Biology Faculty, in 1996. Postdoctoral degree (habilitation) in biological sciences in the discipline biology, Faculty of Natural Sciences, University of Szczecin, Szczecin, in 2009. In 2012...