Search results for: RAILWAY LOAD
-
Electrolytic corrosion of water pipeline system in the remote distance from stray currents– case study
PublicationCase study of corrosion failure of urban water supply system caused by the harmful effects of stray currents was presented. The failure occurred at a site distant from the sources of these currents namely the tramway and railway traction systems. Diagnosis revealed the stray currents flow to pipeline over a remote distance of 800 ÷ 1,000 meters from the point of failure. At the point of failure stray currents flowed from the pipeline...
-
Optimum shape of turnout diverging track with segments of variable curvature
PublicationIn the paper an attempt has been made to focus on shaping the variable curvature in the diverging track of the railway turnout. Basing on some earlier studies, solutions provided with a circular arc in the mid-zone, and in the extreme regions with segments of non-linear curvature of equal length and zero curvature at the start and end of the turnout, have been assumed as models. The most advantageous type of curvature has been...
-
Mathematical modelling of the overhead contact line for the purpose of diagnostics of pantographs
PublicationThe overhead contact line (OCL) is the most effective way for supplying railway electric vehicles. The increase of the speed of the vehicles increases power consumption and requires ensuring proper cooperation of pantographs with OCL. The paper describes the novel mathematical model of the OCL system and the simulation results. The primary objective is a more accurate analysis to increase the reliability of the evaluation of monitoring...
-
Optimization of using recuperative braking energy on a double-track railway line
PublicationIn the introduction, possible ways of reusing energy from recuperation are presented. Next, the paper investigates the possibility of using regenerative braking in the range allowed by the detailed timetable by adopting the method of transferring the recovered electric energy directly to the catenary and immediate use of this energy by another train at the same power section. In the main part of the work, it is shown, that the...
-
Hybrid energy storage forelectric multiple units to operate at the partially electrified line Gdynia -Hel
PublicationThe article presents calculations enabling the selection of an on-board energy storage device to replace diesel-powered trains with modern storage multiple units on the example railway line Gdynia Główna -Hel. The pioneering and currently used storage electric multiple units, mainly in Europe, were presented. The condensed results of the inventory of the line in question, including the technical condition...
-
Energy efficiency of electric multiple units in suburban operation
PublicationThis thesis presents approach to analysis of energy efficiency of a suburban rail network, using novel models developed on the Matlab/Simulink basis. Necessary features and requirements for such models were determined thru in-depth review of the source literature in all applicable fields: electrified transportation systems, electric multiple units construction, vehicle drivetrains and finally, existing simulation methods. Existing...
-
Visual Traffic Noise Monitoring in Urban Areas
PublicationThe paper presents an advanced system for railway and road traffic noise monitoring in metropolitan areas. This system is a functional part of a more complex solution designed for environmental monitoring in cities utilizing analyses of sound, vision and air pollution, based on a ubiquitous computing approach. The system consists of many autonomous, universal measuring units and a multimedia server, which gathers, processes and...
-
Optimization of the efficiency of braking energy recovery in rail transport by changing arrival time
PublicationThe article refers to the previous work of the authors, in which the model of traffic organization of cooperating trains including the optimization of the use of energy returned to the catenary was presented. In the presented article, the model was modified by changing the main control variable, which affects the efficient use of energy. Departure time was changed for the arrival time of the train to the stop or station. The optimization...
-
Smoothed transition curve for railways
PublicationThe work draws attention to the existing situation in the area of transition curves used in the geometric layouts of the railway track. Difficulties in the practical implementation and maintenance of very small horizontal ordinates of the transition curve and the ordinates of the gradient due to cant in the initial section, appearing on smooth transition curves, were indicated. The main reason for this situation was the excessive...
-
Analysis of the Ways to Identify Rail Running Surface Defects by Means of Vibration Signals
PublicationTh e article discusses a preliminary concept of a method enabling the identifi cation of chosen rail running surface defects, such as squats, spalling, and running surface defects, by analysing the parameters of vibration signals. It features a description of the methodology of the conducted tests, the scope thereof, and the selection of the measurement points with specifi c defect types. Th e article covers selected results of...
-
Analysis of turnouts with non-linear curvature of diverging track for different train running speeds
PublicationThe paper deals with the issue of shaping a variable curvature in the diverging track of the railway turnout. Solution without a circular arc in the central zone, comprising two zones of non-linear curvature, of the same length, having zero curvature values at the end points, was adopted as a model, on the basis of the previously conducted dynamic tests. Optimum type of curvature was selected from the point of view of the kinematic...
-
Safety at railway level crossings and Vision Zero
PublicationIn this work, safety analysis at the railway level crossings is presented using advanced mathematical modelling. Resistivity of track subgrade panels is taken into account. The analysis does not refer to the assessment of the current regulations. Specific cases of generalized dynamic system are considered by introducing operations S=Δ, S=P defined in space C(N) of real sequences. In this model, generalized discrete exponential...
-
Technical diagnostics and monitoring of traction current collectors
PublicationNew evaluation methods of the technical condition of rolling stock current collectors are proposed in this paper. The method of automatic measurement of the pantograph static force characteristic, realized when the vehicle runs through the test section of the track with especially prepared overhead line height distribution, has been practically implemented by the Polish Railways. The method of testing the slipper spring suspension...
-
Endoscopic image processing and analysis of pistons' service failures of marine diesel engines
PublicationThe paper deals with diagnostic issues concerning endoscopic examinations of working spaces within marine diesel engines. In the beginning, endoscopy apparatus being on laboratory equipment of the Department of Ship Power Plants of Gdansk University of Technology has been characterized. The endoscopy considerations have been focused on theoretical bases of a digital image processing and especially - on the "Shadow" measurement...
-
Modal analysis of railway current collectors using Autodesk Inventor
PublicationThe paper presents the results of modal analysis of railway current collector type 160EC. In the first place, the analysis was carried out analytically for a simplified two lumped mass pantograph model. Then numerical analysis was conducted in the Autodesk Inventor (AI) on the prepared multibody model using the AI modal analysis algorithm, which is based on the finite element method (FEM). Model elements which are most relevant...
-
Study on applicability of two modal identification techniques in irrelevant cases
PublicationStudy on applicability of two modal identification techniques in irrelevant cases is made in this paper. The following techniques are considered: Peak Picking based on correlation analysis (PP-CA), dedicated for ambient vibrations and Eigensystem Realization Algorithm (ERA), formulated for free decay vibrations investigation. Irrelevant cases are found when analyzed signals are different than recommended to a given technique. The...
-
A dynamic vehicle-bridge model based on the modal identification results of an existing EN57 train and bridge spans with non-ballasted tracks
PublicationThis paper addresses the methodology of the bridge-vehicle dynamic model definition based on the free response measurements of an existing train and existing bridge spans. In the case of the railway vehicle, the methodology uses the impulse excitations of a single car by means of the wedge method. In the case of the bridge spans, free responses are collected after the passages of trains. The global modal parameters (frequencies...
-
New transition curve adapted to railway operational requirements
PublicationThe paper points to the limited possibilities of improving the existing situation in the area of transition curves used in geometrical layouts of the railway track. Difficulties in the practical implementation and maintenance of very small horizontal ordinates of the transition curve and the ordinates of the gradient due to cant in the initial section, appearing on smooth transition curves, were indicated. The main reason for this...
-
DYNAMIC ANALYSIS OF HISTORIC RAILWAY BRIDGES IN POLAND IN THE CONTEXT OF ADJUSTING THEM TO PENDOLINO TRAINS
PublicationThe article presents the dynamic analysis of the historic railway bridge in Tczew as an example of the usefulness of such type of bridge for high-speed trains. The model of the bridge and the simulation of rolling stock passage was performed in SOFISTIK program. The scope of work includes experimental studies, the solution of the problem concerning the correct solution features dynamic model takes into account the dependencies...
-
Diagnostics of the tram track shape with the use of the global positioning satellite systems (GPS/Glonass) measurements with a 20 Hz frequency sampling
PublicationSatellite geodetic measurements used in the diagnosis of railway tracks require professional receivers and a very high frequency rate of data processing. It stems from a significant speed (10 km/h) kinematic measurements carried out during the passage of a measuring platform. The survey results (positions) of deformed railroad track have waveforms nature requiring additional processing methods and approximations. Due to the announcement...
-
Vehicular Communication Environments
PublicationCommunication to and between road vehicles (cars, truck, buses, trains, etc.) are of growing interest. This is partly due to the attractive services that cooperative intelligent transport systems (C-ITSs) provides, mainly in the areas of traffic safety and traffic efficiency. An enabler for C-ITS is wireless vehicle-to-vehicle (V2V) and vehicle-to-infrastructure (V2I) communication, collectively referred to as vehicle-to-X (V2X)...
-
Determination of the tram track axis using a multi receiver GNSS measurement system
PublicationThis article refers to research, that has been conducted by an interdisciplinary research team from the Gdańsk University of Technology and the Maritime University in Gdynia since 2009. These investigation concerns the determination of a railway track axis using the mobile satellite measurement technique. Following the dynamic development of GNSS techniques, that could be seen in the last decade, the team carried out further experiments...
-
Symbolic multibody models for digital-twin applications
PublicationSymbolic generation of multibody systems equations of motion appeared in the 1980s. In addition to their computational advantage over their numerical counterparts, symbolic models can be very easily and straightforwardly interfaced with a wide range of software environments and hardware devices. These two features place this approach in a pole position to participate and intervene in the design of digital twins for systems such...
-
Computer-Aided Design of Railroad Horizontal Arc Areas in Adapting to Satellite Measurements
PublicationThis paper presents a method of designing railway sections located in horizontal arcs. The adopted procedure is universal, i.e., it creates the possibility of varying both the type and the length of the assumed transition curves. This means that the applied analytical formulas apply to the boundary conditions of the transition curves and all of the simplifications widely existing in common algorithms have been eliminated. The presented...
-
Selected Problems of Transport in Port Towns – Tri-City as an Example
PublicationPort towns are strategic places from the point of view of transport systems. They form integration junctions for various transport branches , apart from the traditional - road and railway ones , also for water( sea) transport which is active there. Moreover, air transport comes also into consideration , whose efficient functioning must be connected with good accessibility, that concerns sea transport as well. Efficient and...
-
Identification of safety hazards and their sources in tram transport
PublicationBoth in Poland and in most countries of the European Union, the tram infrastructure is extensively expanding. Contemporary low-floor trams are constructed according to different technical assumptions than typical railway vehicles or high floor trams. In Poland such vehicles rides often on lines designed according to standards developed to the classical vehicles. At the same time, the intensity of road traffic and the number of...
-
Forecasting of railway track tamping based on settlement of sleepers using fuzzy logic
PublicationThe sleepers in a railway track transfer vertical, transverse and longitudinal loads to the track ballast and subgrade. The sleepers allow for keeping the distance between the rails constant. The thickness of ballast should be between 16 and 35 cm depending on the design standard of the track, and it should be densified where the ballast supports the sleeper. The exploitation causes contamination of the ballast, crushing the material...
-
Reprezentation of mechanic hysteresis in a railway track using the Preisach model
PublicationThis paper presents an implementation of the classic scalar Preisach model to describe the hysteresis phenomenon created in a railway track subjected to lateral (in the horizontal plane) displacements. The principles of the Preisach theory and the scalar mathematical model of the mechanical hysteresis that is based on statistically distributed modified hysteresis operators are briefly presented. This article presents the characteristic...
-
A new approach to determination of the two-mass model parameters of railway current collector
PublicationThe paper presents two mathematical models of railway current collectors both with two degrees of freedom. The first one, hereinafter Pantograph Articulated Model (PAM), has one degree of freedom in rotational motion and the second degree of freedom in translational motion. The second model, called henceforth as Pantograph Reference Model (PRM), has both degrees of freedom in translational motion. Differential equations of the...
-
The process of identification of the track's geometrical layout and the alignment project based on the of satellite measurements
PublicationIn the paper a methodology of restoring of railway track’s geometrical shape in a horizontal plane on the base of conducted mobile satellite surveying was presented. The authors proposed a calculating algorithm for designing the track sections placed in horizontal arcs. In the algorithm an analytical methodology with mathematical formulas is applied. The procedure has an universal character, i.e. provides the possibility of varying...
-
Satellite inventory of tram track geometrical layout
PublicationIn the paper a methodology of restoring of railway track’s geometrical shape in a horizontal plane on the base of conducted mobile satellite surveying was presented. The authors proposed a calculating algorithm for designing the track sections placed in horizontal arcs. In the algorithm an analytical methodology with mathematical formulas is applied. The procedure has an universal character, i.e. provides the possibility of varying...
-
A new approach to determination of the two-mass model parameters of railway current collector
PublicationThe paper presents two mathematical models of railway current collectors both with two degrees of freedom. The first one, hereinafter Pantograph Articulated Model (PAM), has one degree of freedom in rotational motion and the second degree of freedom in translational motion. The second model, called henceforth as Pantograph Reference Model (PRM), has both degrees of freedom in translational motion. Differential equations of the...
-
A PROPOSAL FOR ONE-IMAGE PHOTOGRAMMETRY SYSTEM FOR MEASURING THE CLEARANCE DISTANCE. CASE STUDY
PublicationMeasurement of the clearance distance (both in the context of the rail and road) is one of the current and increasingly discussed topics in the context of photogrammetric and image processing (computer vision) methods. The article presents a description of a simple and rapid method of measure the clearance distance between the obstacles by using one-image photogrammetry. The proposed method was tested for the railway, tram and...
-
Design of reverse curves adapted to the satellite measurements
PublicationThe paper presents a new method for designing railway route in the direction change area adapted to the Mobile Satellite Measurements technique. The method may be particularly useful in the situations when both tangents cannot be connected in an elementary way using a circular arc with transition curves. Thus, the only solution would be the application of two circular arcs of opposite curvature signs, that is, the use of an inverse...
-
Identification of acoustic event of selected noise sources in a long-term environmental monitoring systems
PublicationABSTRACT Undertaking long-term acoustic measurements on sites located near an airport is related to a problem of large quantities of recorded data, which very often represents information not related to flight operations. In such areas, usually defined as zone of limited use, often other sources of noise exist, such as roads or railway lines treated is such context as acoustic background. Manual verification of such recorded data...
-
Wavelet transform-based approach to defect identification in railway carbon contact strips.
PublicationPantographs of electric rail vehicles are fitted with carbon contact strips, which slide along the contact wire of catenary to provide constant electrical contact. Contact strips are exposed to wear and damages. Using damaged contact strips significantly increases the risk of catenary rupture. Therefore, their technical condition has to be inspected frequently. In previous work a 3D laser scanning system was proposed for recording...
-
Optimization of Train Energy Cooperation Using Scheduled Service Time Reserve
PublicationThe main aim of the paper was to develop an innovative approach to the preliminary estimation possibility of train energy cooperation based on data from timetables, without traction calculations. The article points out the need to strive for sustainable and environmentally friendly transport. It was pointed out that rail transport using electric traction is one of the more ecological branches of transport. It also offers a number...
-
Arching of railway turnouts by analytical design method
PublicationThe paper involved the issue of arching of the railway turnouts. This is an issue which is given relatively less attention to scientific and research activities. Reference has been made to the book by Wladyslaw Rzepka, under the title „Curved turnouts in plan and profile”, which has been used in Poland for more than 50 years as the main source of information relating to the turnouts on the curve. The book is a compilation of elaborations...
-
SiC-Based Power Electronic Traction Transformer (PETT) for 3 kV DC Rail Traction
PublicationThe design of rolling stock plays a key role in the attractiveness of the rail transport. Train design must strictly meet the requirements of rail operators to ensure high quality and cost-eective services. Semiconductor power devices made from silicon carbide (SiC) have reached a level of technology enabling their widespread use in traction power converters. SiC transistors oering energy savings, quieter operation, improved reliability...
-
Analytical design method for widening the intertrack space
PublicationThe paper involved the issue of arching of the railway turnouts. This is an issue which is given relatively less attention to scientific and research activities. Reference has been made to the book by Wladyslaw Rzepka, under the title „Curved turnouts in plan and profile”, which has been used in Poland for more than 50 years as the main source of information relating to the turnouts on the curve. The book is a compilation of elaborations...
-
Algorithm for Automatic Wear Estimation of Railway Contact Strips Based on 3D Scanning Results
PublicationElectric rail vehicles use current collection system which consists of overhead contact line and a current collector (pantograph) mounted on the roof of a vehicle. A pantograph is equipped with contact strips, which slide along the contact wire, ensuring steady electric contact. Contact strips are made of carbon layer, fixed to an aluminum carrier. The carbon layer wears down due to friction. Using overly worn contact strips increases...
-
Polish FDI in Central Asian Countries
PublicationSince gaining independence, Kazakhstan, Kyrgyzstan, Tajikistan, Turkmenistan and Uzbekistan gradually opened their markets to foreign investors. Before Poland’s accession to the European Union, the activities of Polish investors in Kazakhstan, Kyrgyzstan, Tajikistan, Turkmenistan and Uzbekistan were based on bilateral treaties concluded by Poland with those countries. Later, except Turkmenistan, they were governed by the partnership...
-
Designing of Track Axis Alignment with the Use of Satellite Measurements and Particle Swarm Optimization
PublicationDesigning of the track’s alignment is a key issue from the point of view of maintaining of proper geometries. The paper presents a design method for sections of railway line located in the horizontal arch. The method is adapted to the technique of mobile satellite measurements. The general principles of this measurement method have been described in the article. A project's solution has been presented using mathematical notation...
-
Modal Analysis of a Steel Radial Gate Exposed to Different Water Levels
PublicationWith the increase in water retention needs and planned river regulation, it might be important to investigate the dynamic resistance of vulnerable elements of hydroelectric power plants, including steel water locks. The most frequent dynamic loads affecting hydroengineering structures in Poland include vibrations caused by heavy road and railway traffic, piling works and mining tremors. More destructive dynamic loads, including...
-
Effect of Processing Parameters on Strength and Corrosion Resistance of Friction Stir-Welded AA6082
PublicationThe friction stir welding method is increasingly attracting interest in the railway sector due to its environmental friendliness, low cost, and ease of producing high-quality joints. Using aluminum alloys reduces the weight of structures, increasing their payload and reducing fuel consumption and running costs. The following paper presents studies on the microstructure, strength, and corrosion resistance of AA6082 aluminum alloy...
-
The issue of uncertainty of visual measurement techniques for long distance measurements based on the example of applying electric traction elements in diagnostics and monitoring
PublicationRail transport is the most economical and energy-effective in the field of land transport, in particular electrified. In order to ensure efficient and reliable operation of electrified rail transport, the issues of monitoring and diagnostics of the traction infrastructure and vehicles are extremely important. The most critical point in the transmission of electric energy to the vehicle is the sliding contact of the current collector...
-
Impact of Large-scale urban interventions on contemporary city centers. Gdansk case study. Wpływ przedsiewzięć urbanistycznych dużej skali na centra miast. Studium przypadku Gdańska
PublicationLarge scale urban interventions have become a common development practice in cotemporary cities, allowing achieving rapid changes in their urban structure. They can be analyzed taking into account various perspectives. Some of them include planning and development models, transformation of brownfields and other types of distressed urban areas, as well as consequences and results of their implementation in existing urban structures....
-
The significance of the underground experience: Selection of reference design cases from the underground public transport stations and interchanges of the European Union
PublicationAbstract Background Recent research into the way public transport users appreciate stations and interchanges has highlighted several key aspects. Importantly, the optimization of these facilities should not simply aim to resolve dissatisfiers, but should also focus on addressing satisfiers, through the incorporation of factors such as comfort and experience. ‘Soft requirements,’ which have emerged in architecture and urban design,...