Filters
total: 209
Search results for: THERMAL STRESSES
-
Study of Non-Newtonian biomagnetic blood flow in a stenosed bifurcated artery having elastic walls
PublicationFluid structure interaction (FSI) gained attention of researchers and scientist due to its applications in science felds like biomedical engineering, mechanical engineering etc. One of the major application in FSI is to study elastic wall behavior of stenotic arteries. In this paper we discussed an incompressible Non-Newtonian blood fow analysis in an elastic bifurcated artery. A magnetic feld is applied along x direction. For...
-
Wave transmission across surface interfaces in lattice structures
PublicationWithin the lattice dynamics formulation, we present an exact solution for anti-plane surface waves in a square lattice strip with a surface row of material particles of two types separated by a linear interface. The considered problem is a discrete analog of an elastic half-space with surface stresses modelled through the simplified Gurtin–Murdoch model, where we have an interfacial line separating areas with different surface...
-
Experimental Study of Dapped-End Beams Subjected to Inclined Load
PublicationThis paper presents the results of an experimental investigation of the reinforced concrete (RC) dapped-end beams loaded with inclined forces, compared to identical ones loaded with vertical forces only. Such a load may occur in, for example, Gerber's joints or in dapped-end beams supported on corbels, where the vertical gravitation force is additionally completed with horizontal forces caused by temperature differences, shrinking,...
-
Effect of bitumen characteristics obtained according to EN and Superpave specifications on asphalt mixture performance in low-temperature laboratory tests
PublicationThe paper aims to identify those characteristics of bitumen which have the greatest impact on asphalt mixture low-temperature performance. It was observed that stiffness and m-value of bitumen from BBR test were moderately related to stiffness and m-value of asphalt mixture obtained from 3 PB test. Simultaneously those rheological properties significantly impact on cryogenic stresses induced during TSRST test. The multiple regression...
-
On weak solutions of boundary value problems within the surface elasticity of Nth order
PublicationA study of existence and uniqueness of weak solutions to boundary value problems describing an elastic body with weakly nonlocal surface elasticity is presented. The chosen model incorporates the surface strain energy as a quadratic function of the surface strain tensor and the surface deformation gradients up to Nth order. The virtual work principle, extended for higher‐order strain gradient media, serves as a basis for defining...
-
Design and material selection for a patient transport device in field hospitals
PublicationACKGROUND: A major cause of patient and hospital worker injuries occurs transferring patients between two planes. The main aim of this paper was to propose a design of patient’s lift and transfer apparatus for use in field hospitals. The assumption was to design lightweight, durable and ergonomic device using innovative material. The authors concentrated on partial elimination of manual lifting in order to device could work both...
-
ATTEMPT AT EVALUATING THE INFLUENCE OF BENDING STRESS ON SHAFT WEAR PROCESSES IN WATER LUBRICATED SLIDING BEARING WITH A RUBBER BUSHING
PublicationWater lubricated bearings find increasingly wide application in shipbuilding or hydro–power industry, the popularity stemming from their numerous advantages. Unfortunately, as it turns out, water lubricated bearings do not always meet expectations, as on occasion they become subject to intense, premature wear which requires costly repair. One of the still unexplained phenomena is the process of excessive bearing wear, in particular...
-
Tests of bond between concrete and steel bars – literature background and program of own research
PublicationThis article deals with the issue of the bond between concrete and reinforcement. The bond is crucial for reinforced concrete elements because it is possible to transfer forces (stresses) from concrete to the reinforcement. Basic information related to the cooperation of concrete and rebars was recalled in the article. Selected issues concerning theoretical and numerical analysis as well as experiments of the bond phenomenon were...
-
On the influence of a surface roughness on propagation of anti-plane short-length localized waves in a medium with surface coating
PublicationWe discuss the propagation of localized surface waves in the framework of the linear Gurtin–Murdoch surface elasticity and taking into account a roughness of a free boundary. We derive a boundary-value problem for anti-plane motions with curvilinear boundary and surface stresses. Using the asymptotic technique developed earlier, we obtain the form of a localized wave and analyze its amplitude evolution. As the main result we present...
-
Anti-plane surface waves in media with surface structure: Discrete vs. continuum model
PublicationWe present a comparison of the dispersion relations derived for anti-plane surface waves using the two distinct approaches of the surface elasticity vis-a-vis the lattice dynamics. We consider an elastic half-space with surface stresses described within the Gurtin–Murdoch model, and present a formulation of its discrete counterpart that is a square lattice half-plane with surface row of particles having mass and elastic bonds different...
-
REINFORCED CONCRETE SUPPORTING CONSTRUCTION OF THE STADIUM COVER FOR EURO 2012 IN GDAŃSK
PublicationIn the article structural issues that connected with the reinforced concrete supporting construction of the stadium roofing for EURO 2012 in Gdańsk were described. In the first part of the article the concept of stadium foundation were described. In the second the static - strength analysis for two variants fastening together individual foundation elements were made. The two assumed geometrically different concept of foundation...
-
Fracture mechanics model of cutting power versus widespread regression equations while wood sawing with circular saw blades
PublicationA comparison of the theoretical cutting power consumption results forecasted with the model (FM_CM model) which include work of separation (fracture toughness) in addition to plasticity and friction, and two widespread regression equations while wood sawing with circular saw blades has been described. in and cutting power consumption forecasted. In computations of the cutting power consumption during rip sawing of Scots pine wood...
-
Empirical verification in industrial conditions of fracture mechanics models of cutting power prediction
PublicationA comparison of experimental results obtained in the industrial conditions at a sawmill located in the Baltic Natural Forest Region (PL) and theoretical cutting power consumption forecasted with the models which include work of separation (fracture toughness) in addition to plasticity and friction has been described. In computations of cutting power consumption during rip sawing of Scots pine wood (Pinus sylvestris L.) values of...
-
Numerical analysis and in situ tests of the Grot Rowecki Bridge in Warsaw
PublicationThe paper presents the FEM analysis of the reconstructed the Grot-Rowecki Bridge over Vistula river in Warsaw. The bridge has seven spans and consists of two independent structures with the longest spans of 120 m. After reconstruction the bridge is over 10 m wider. The numerical, nonlinear analysis has been con-ducted on a global and local FEM models. These models are defined so as they strictly comply with global structural bridge...
-
Properties of surface layers of duplex stainless steel after burnishing processes
PublicationStress corrosion cracking resistance of cold worked layers of 25 Cr duplex stainless steel grade UR52N+ has been investigated. The surface layers were performed through burnishing treatment. The residual stresses at surface layers were determined using grazing angle incidence X-ray diffraction method (g-sin2 Ψ). Corrosion tests were performed with the use of Slow Strain Rate Test technique in boiling 35% MgCl2 solution. It has...
-
Controling w zarządzaniu bezpieczeństwem pracy
PublicationW artykule przedstawiono możliwość wykorzystania controllingu do badania zagrożeń w procesie pracy. Dla oceny rozwiązań usprawniających wprowadzono pojęcie oszczędności zasobu typu praca i typu materiał, zużywanych w procesie realizacji zadań wytwórczych. Artykuł podkreśla możliwość osiągania efektów ekonomicznych (ograniczenia kosztów) w wyniku poprawy warunków pracy.CONTROLLING IN WORK SAFETY MANAGEMENTThe article presents the...
-
Joints Of Steel Sandwich Structures
PublicationSteel sandwich structures are perceived as alternatives to single-skin welded structures in the shipbuilding industry due its advantages like significant reduction of mass in relation to typical single skin structure. However, beside problems with their strength properties itself, applications in real structures requires of solving the problem of joining, both for connection sandwich to sandwich as well as sandwiches to single-shell...
-
Influence of pitting corrosion on fatigue and corrosion fatigue of ship and offshore structures. Part II: Load - pit crack interaction
PublicationIn the paper has been discussed influence of stresses on general corrosion rate and corrosion pit nucleation and growth rate, whose presence has been questioned by some authors but accepted by most of them. Influence of pit walls roughness on fatigue life of a plate suffering pit corrosion and presence of so called "non damaging" pits which never lead to initiation of fatigue crack, has been presented. Possibility of prediction...
-
Structural design and sensitivity analysis of semi-rigid pavement of a motorway
PublicationThis paper presents application of mechanistic-empirical methods in design of semi-rigid pavement for a section of a motorway in Poland. The stage construction was assumed. Three fatigue criteria were applied in the design. For asphalt fatigue cracking and subgrade soil the criteria from the Asphalt Institute (USA) were applied. For fatigue cracking of cement stabilized bases the Dempsey (USA) and De Beer (South Africa) criteria...
-
COMPARATIVE NUMERICAL ANALYSIS OF DIFFERENT STRENGTHENING SYSTEMS OF HISTORICAL BRICK ARCHES
PublicationThe article presents a comparative numerical analysis of various ways to strengthen historical brick arches. Five ways of strengthening brick arches with steel tie-rods have been proposed. Two of these involve the use of braces wrapped around pillars supporting the arch connected with a tie-rod; another two ways involve the use of the tie-rods with welded metal sheets of different sizes; the last way involves the use of the tie-rod...
-
Examination of selected failure criteria with asymmetric shear stresses in the collapse analysis of laminated shells
PublicationThe paper is concerned with failure analysis of composite shells performed with the usage of the nonlinear 6‐parameter shell theory with drilling rotation degree of freedom. This special theory embodies naturally unlim-ited translations and rotations and is suitable for analysis of irregular shells for instance with various, partic-ularly orthogonal, intersections. The presence of the drilling rotation is inherently accompanied...
-
Remarks on the Subject of Back-Up Protection of Residual Current Devices
PublicationResidual current devices without integral overcurrent protection (RCCBs) are back-up protected by fuses or miniature circuit-breakers (MCBs). If the latter are used, special attention must be given to the coordination between an RCCB and an MCB. This paper indicates probable cases of the aforementioned devices coordination, in which back-up protection of the RCCB is not adequate. A laboratory test has shown that depending on the...
-
Preliminary designing method of external pressure vessels for sea subsurface aplications
PublicationThis paper describes a unique engineering method intended for the preliminary designing of marine subsurface buoy mooring systems. The solved designing problem consists in determining geometrical parameters and selecting structural materials for a vessel of a buoyancy necessary to contain measuring instruments of a given mass, as well as its maximum dimensions and operational submersion depth. The assumed variability range of...
-
Problems of analytical determination of journal bearing bush fatigue strength estimates
PublicationProblems connected with determination of stress distribution in sliding layer of thinwalled bearing bushes, investigated in bearing fatigue test rigs, have been presented. Using an example of plain bearings tested in the fatigue machine SMOK (built at the Gdask University of Technology) problems with obtaining a convergence of iterative procedure for determining the fatigue strength estimators of bearing alloy surface layer are...
-
SHEAR YIELD STRESSES AND FRACTURE TOUGHNESS OF SCOTS PINE (PINUS SYLVESTRIS L.) ACCORDING TO THE RAW MATERIAL PROVENANCE
PublicationIn this paper values of the fracture toughness and of shear yield stress in the shear zone of Scots pine are presented. Tests of cutting were carried on samples of Scotch pine (Pinus sylvestris L.) wood of five provenances from Poland. These experimentally cutting tests were carried on the sash gang saw PRW-15M and the values of cutting power were obtained. The values of fracture toughness and shear yield stress based on Atkins’s...
-
Preliminary investigations of effect of conditions of FCAW process on diffusible hydrogen content in deposited metal
PublicationOne of the types of hydrogen degradation of steel welded joints is cold cracking. The direct cause of the formation of cold cracks is simultaneous presence of hydrogen, residual stresses and brittle structure. The way of preventing the occurring of degradation is to eliminate at least one of these factors. Practice has shown that the best solution is to control the amount of hydrogen in deposited metal. In this paper the state...
-
The Discrete-Continuous, Global Optimisation of an Axial Flow Blood Pump
PublicationThis paper presents the results of the discrete-continuous optimisation of an axial flow blood pump. Differential evolution (DE) is used as a global optimisation method in order to localise the optimal solution in a relatively short time. The whole optimisation process is fully automated. This also applies to geometry modelling. Numerical simulations of the flow inside the pump are performed by means of the Reynolds-Average Navier-Stokes...
-
The Effect of Flexible Pavement Mechanics on the Accuracy of Axle Load Sensors in Vehicle Weigh-in-Motion Systems
PublicationWeigh-in-Motion systems are tools to prevent road pavements from the adverse phenomena of vehicle overloading. However, the effectiveness of these systems can be significantly increased by improving weighing accuracy, which is now insufficient for direct enforcement of overloaded vehicles. Field tests show that the accuracy of Weigh-in-Motion axle load sensors installed in the flexible (asphalt) pavements depends on pavement temperature...
-
Interaction of the conserved region 4.2 of sigma(E) with the RseA anti-sigma factor
PublicationEo-E RNA polymerase transcribes a regulon of folding factors for the bacterial envelope and is induced by physical and chemical stresses. The RseA anti-sigma factor inhibits the activity of Esigma(E) RNA, polymerase. It is shown here that the N-terminal portion of sigma(E), residues 1-153, binds core RNA polymerase. RseA interacts with residues 154-191 of sigma(E), a site that is homologous to region 4, the sigma factor binding...
-
Comparative tests of the wall thickness effect of a glass-reinforced thermosetting plastic coating with a non-circular cross section in a soil-coating object for economic aspect
PublicationCulvert structures made of plastics are employed extensively in the construction of new facilities as well as the renovation of existing ones. Due to the high costs of materials required for the manufacturing of these goods, the objective of this research is focused to lessen the thickness of the walls, which may, on the other hand, result in a reduction in the stiffness of the system. In the course of the testing, the structure...
-
SHORT REVIEW AND 3-D FEM ANALYSIS OF BASIC TYPES OF FOUNDATION FOR OFFSHORE WIND TURBINES
PublicationSome problems of the foundations of offshore wind turbines are considered in this paper. A short review is presented on the two basic types of foundations, i.e. monopiles and gravity foundations, including their basic features and applications as well as general design considerations. Also, some issues regarding analysis are discussed, including geotechnical problems and modelling techniques. A numerical model of offshores turbine...
-
Correlation between natural frequencies and buckling load in a stiffened shell
PublicationThe paper deals with correlation between natural frequencies and buckling load of a stiffened shell composed of corrugated sheets and vertical stiffeners (columns). The simplified shell segment represents the buckling behaviour of a whole silo with sparsely distributed columns. The paper covers variants of linear buckling anal-yses, dynamic eigenvalue analyses and geometrically non-linear analyses of a segment modelled with shell...
-
A model of liquid film breakdown formed due to impingement of a two-phase jet on a horizontal surface
PublicationThe present work aims to provide an explanation to the phenomenon of breakdown of the thin liquid film created by impinging two-phase, liquid-gas jet. Existing in the literature models describe merely thebreakdown of single phase liquid films. The model presented here is based on examination of mass and energy equations under the applied criterion of the minimum of total energy. That allows to determinethe minimum thickness of...
-
Strength analysis of container ship subjected to torsional loading
PublicationThe objective of this work is to investigate the torsional response of a container ship, with particular consideration of the warping effect. Two different models are investigated. In the first case, the full length model of a ship is analyzed and a distributed load is applied with the use of a novel approach. The model is supported in the torsional centre of the cross-section, which is derived analytically. In the second case,...
-
Determination of the Bending Properties of Wire Rope Used in Cable Barrier Systems
PublicationThis paper presents research on the bending properties of 3 × 7 19-mm wire rope commonly used in road cable barriers. A total of 19 experimental tests were conducted. In addition, two nonlinear 3D numerical models of the wire rope using beam and solid finite elements were developed. Based on these models, four numerical simulations were carried out. The numerical results were validated against the experimental ones and a very good...
-
Erroneous GNSS Strain Rate Patterns and their Application to Investigate the Tectonic Credibility of GNSS Velocities
PublicationThe paper concerns investigation of the credibility of tectonic interpretation of GNSS strain rates. The analysis was focused on stable regions, where the crustal deformations are small and the reliability of GNSS velocities is questionable. We are showing how the unreliable motion of stations affects calculated strains around them. We expressed distribution of local principal strains by a sinusoidal function and used them to investigate...
-
Numerical investigations of discrete crack propagation in Montevideo splitting test using cohesive elements and real concrete micro-structure
PublicationThe paper is aimed at accurately predicting the discrete fracture process in concrete specimens under complex stress states in two dimensional (2D) simulations. Plain concrete specimens subjected to Montevideo splitting test (MVD) were used for consideration due to non-negligible shear stresses impact in this type of test. In order to reflect the heterogeneous nature of the concrete, the meso-structure of the samples was included...
-
Experimental research of the effect of face milling strategy on the flatness deviations
PublicationIn this paper the dependencies between face milling strategy of EN AW6082-T6 aluminum alloy samples, with difference thicknesses (6, 8, and 12 mm) and two cold rolling directions, and flatness deviations were presented. Three strategies of milling included different proportions of material removed from both sides of the plates. This approach allowed to control the proportions of residual surface stresses on both sides of the specimens,...
-
Simple Computational Methods in Predicting Limit Load of High-Strength Cold-Formed Sections due to Local Buckling: A Case Study
PublicationCold-formed thin-walled sections are prone to local buckling caused by residual stresses, geometrical imperfections and inconsistency of material properties. We present a real case of buckling failure and conduct a numerical and experimental study aimed to identify methods capable of predicting such failures. It is important because designers of structures are getting more FEA-oriented and tend to avoid lengthy procedures of cold-formed...
-
Estimation of fracture toughness and shear yield stress of orthotropic materials in cutting with rotating tools
PublicationThe cutting force is an energetic effect of splitting material, and might be considered from a point of view of modern fracture mechanics. Forecasting of the shear plane angle in cutting broaden possibilities for modelling of the cutting process even for thin uncut chips. Such mathematical model has been developed here for description of the orthotropic materials’ cutting on the base of fracture theory, and includes work of separation...
-
Impact of Tensile and Compressive Stress on Classical and Acoustic Barkhausen Effects in Grain-Oriented Electrical Steel
PublicationIn this paper, we present the results of the investigation of impact of tensile and compressive stress on the classical Barkhausen effect, magnetoacoustic emission (MAE) signal properties, and B(H) hysteresis loops for grain-oriented (GO) electrical steel. Samples have been glued to a nonmagnetic steel bar and stressed within elastic range (±800 μdef) by means of four-point bending method. The samples were cut out in two directions...
-
The influence of reinforcement on load carrying capacity and cracking of the reinforced concrete deep beam joint
PublicationThe paper presents the results of experimental research of the spatial reinforced concrete deep beam systems orthogonally reinforced and with additional inclined bars. Joint of the deep beams in this research was composed of the longitudinal deep beam with a cantilever suspended at the transversal deep beam. The cantilever deep beam was loaded throughout the depth and the transversal deep beam was loaded at the mid-span by longitudinal...
-
Cable-stayed cantilever structures as an expat of unique application in the construction of a building located in seismic area – an author’s project of multifunctional building in Lisbon, Portugal
PublicationThe article presents numerical simulations for the modelling of seismic impact on the structure of unique cantilever cablestayed structure with application of two methods. The Response Spectrum method, in which a spectrum of the structure's responses to an earthquake's impact is generated and the Accelerogram method, in which we generate dynamic load in the form of a diagram of the connection between acceleration and time for...
-
MEMORYSCAPES OF EASTERN POLAND
PublicationThe text investigates new phenomena emerging in the field of social memory and commemoration in contemporary Poland. On the basis of field analyses, case studies and theoretical, transdisciplinary approaches, the paper discusses the issue of contemporary memoryscapes in eastern Poland (Bialystok and Lublin). These emerging forms of remembrance are the result of the sophisticated interplay between different actors involved in the...
-
Static and dynamic concrete calculations: Breakable aggregates in DEM model
PublicationThe paper deals with the calculations of a 3-point bending beam under static and dynamic loads. The real microstructure was obtained from laboratory tests using micro-tomography images. The quasi-static results were compared directly with experimental data at both macro and micro levels. Subsequently, higher strain rates were applied to investigate dynamic effects. The study focused on the influence of dynamic loading on the macroscopic...
-
Modelling of shear zones during quasi-static granular silo flow using material point method (MPM)
PublicationThe paper focuses on confined silo flow of cohesionless sand. The problem considered is a quasi-static flow in a plane strain model silo with parallel walls simulated with the material point method (MPM). The simulation used a non-local hypoplastic constitutive model. Initially, the paper validated the implemented numerical approach with basic element tests and a plane strain compression test. The subsequent MPM calculations for...
-
Shear band evolution phenomena in direct shear test modelled with DEM.
PublicationA direct shear test is widely used in the geotechnical engineering field. It is an easy and quick test to measure the shear properties of soil. This test often replaces more expensive and difficult tri-axial shear test. Despite that the direct shear test is known and used for a long time, it is still not well investigated at the grain scale. This paper deals with the micro behaviour of the cohesionless sand inside the direct shear...
-
Anti-plane shear waves in an elastic strip rigidly attached to an elastic half-space
PublicationWe consider the anti-plane shear waves in a domain consisting of an infinite layer with a thin coating lying on an elastic half-space. The elastic properties of the coating, layer, and half-space are assumed to be different. On the free upper surface we assume the compatibility condition within the Gurtin–Murdoch surface elasticity, whereas at the plane interface we consider perfect contact. For this problem there exist two possible...
-
Experimental and analytical analysis of punching shear in flat slabs supported on column topped with concrete head
PublicationAn experimental laboraatory test of the two series of slab-column elements topped with drop panels of varying sizes is described in this paper. The scope of the paper is to investigate the influence of the drop panel size and stiffness on the behaviour of the connection between the flat slab and the column topped by the concrete head. The impact of the head size and stiffness is analysed analytically and experimentally. The experimental...
-
Agile Requirements Prioritization in Practice: Results of an Industrial Survey
PublicationAgile software development stresses the importance of providing the customer with a product of a maximized business value. To achieve that, requirements prioritization is used. Agile development methods like Scrum define guidelines for prioritization, however practitioners do not necessarily have to follow them. Our goal was to investigate the industry practice related to requirements prioritization process, including its timing,...