Search
Search results for: STEADY-STATE AND TRANSIENT METHOD
-
Systematic comparison of a biotrickling filter and a conventional filter for the removal of a mixture of hydrophobic VOCs by Candida subhashii
PublicationThis work systematically compared the potential of a conventional fungal biofilter (BF) and a fungal biotrickling filter (BTF) for the abatement of a mixture of hydrophobic volatile organic compounds (VOCs). Candida subhashii was herein used for the first time, to the best of the author's knowledge, to remove n-hexane, trichloroethylene, toluene and α-pinene under aerobic conditions. C. subhashii immobilized on polyurethane foam...
-
Analysis of Induced Voltages and Power Losses in High Voltage Power Cables for Selected Methods of Cables Sheaths Bonding
PublicationPower is increasingly supplied to city centres with 110 kV cable lines. This is a convenient way to supply power, and practically the only one possible in areas of dense urban development. A high-voltage cable contains a coaxial metallic sheath, in which in normal operation and in fault conditions (during short-circuits) significant line-to-earth voltages can be induced, which threatens electric shock and/or damage to the cable’s...
-
The use of Acoustic Emission to identification damages bearings the main and crank engines about the automatic ignition
PublicationThe article describes the laboratory tests, which make the first stage of the study concerning the use of the AE method to determine the technical state of the slide bearings in engines with self-ignition. The aim of the present tests was to compare the recorded signals in relation to the technical state of the material of the bearing bush and to check the possibility of using the AE method in determining the transition moment...
-
A Numerical Model Study on Ice Boom in a Coastal Lake
PublicationA numerical study on the effectiveness of the proposed ice boom to be installed near the entrance of Lake Notoro, Hokkaido, Japan to prevent sea ice moving into the lake is presented. A two-dimensional hydro–ice dynamics model was modified to allow for the treatment of ice-boom interaction with the effect of tidal current. The numerical model is a coupled hydrodynamic and ice dynamic model. The ice dynamic component uses a Lagrangian...
-
Diagnosing marine turbine engines through energy characteristics of their flow section
PublicationThe aim of the performed research was to develop of diagnostic method of the flow section of a marine turbine combustion engine based on the level of delamination of its energy characteristics. The here adopted diagnostic model provides for a formulation of the evaluation of the technical conditions based on the measurements of the parameters of the thermodynamic medium in the characteristic control cross-sections of the engine...
-
Method for universal detection of two-photon polarization entanglement
PublicationDetecting and quantifying quantum entanglement of a given unknown state poses problems that are fundamentally important for quantum information processing. Surprisingly, no direct (i.e., without quantum tomography) universal experimental implementation of a necessary and sufficient test of entanglement has been designed even for a general two-qubit state. Here we propose an experimental method for detecting a collective universal...
-
A Universal Gains Selection Method for Speed Observers of Induction Machine
PublicationProperties of state observers depend on proper gains selection. Each method of state estimation may require the implementation of specific techniques of finding those gains. The aim of this study is to propose a universal method of automatic gains selection and perform its verification on an induction machine speed observer. The method utilizes a genetic algorithm with fitness function which is directly based on the impulse response...
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
Three-dimensional numerical investigation of hybrid nanofluids in chain microchannel under electrohydrodynamic actuator
PublicationEnergy efficiency enhancement methods have received considerable attentionwithin the industry and scientific community, owing to the rising concern ofglobal energy sustainability. The present article attempts to scrutinize the effectsof electrohydrodynamics and nanofluids on the rate of heat transfer and fluidflow in the 3-D chain microchannels. Improved heat exchangers (e.g., chainmicrochannel) would have a key role in increasing...
-
CREATING A RANKING OF DIAGNOSTIC PARAMETERS FOR THE DYNAMIC PROCESS OF A MARINE COMBUSTION ENGINE IN THE ASPECT OF MULTI-CRITERIA EVALUATIONS
PublicationThe change of some of the engine’s structural parameters affects the change of toxic compound emission in exhaust gases. It mainly applies to the damage sustained by the charge exchange system as well as the fuel system and the engine supercharging system. These changes are definitely higher during dynamic states and the related transient states. As such, it is possible to speak of a diverse sensitivity of the diagnostic parameters...
-
Comparison of simplified sum-over-state expressions to calculate resonance Raman intensities including Franck-Condon and Herzberg-Teller effects
PublicationSum-over-state (SOS) expressions to simulate absorption spectroscopy and resonance Raman (RR) scattering including Franck-Condon (FC) and Herzberg-Teller (HT) effects are described. Starting from the general SOS method, several simplified SOS formulae are derived. In particular, within the so-called independent mode displaced harmonic oscillator model, it is shown that including the vibronic structure in the absorption and RR spectra...
-
Ground lemon and stevia leaves as renewable functional fillers with antioxidant activity for high-density polyethylene composites
PublicationThe development of new sustainable material solutions in the processing of thermoplastic polymers concerns both the application of biopolymers and the use of valorized plant derivatives as fillers and modifiers of petrochemical polymers. Herein, the possibility of using unprocessed raw parts of two commonly used in the food industry leaves, i.e., lemon (LL) and stevia (ST), as active and functional fillers for high-density polyethylene...
-
Tailoring Diffusional Fields in Zwitterion/Dopamine Copolymer Electropolymerized at Carbon Nanowalls for Sensitive Recognition of Neurotransmitters
PublicationThe importance of neurotransmitter sensing in the diagnosis and treatment of many psychological illnesses and neurodegenerative diseases is non-negotiable. For electrochemical sensors to become widespread and accurate, a long journey must be undertaken for each device, from understanding the materials at the molecular level to real applications in biological fluids. We report a modification of diamondized boron-doped carbon nanowalls...
-
Charge-based deep level transient spectroscopy of B-doped and undoped polycrystalline diamond films
PublicationThe undoped and B-doped polycrystalline diamond thin film was synthesized by hot filament chemical vapor deposition and microwave plasma, respectively. The structural characterization was performed by scanning electron microscopy, X-ray diffraction and Raman spectroscopy. The electrical properties of synthesized diamond layer were characterized by dc-conductivity method and charge deep level transient spectroscopy. The B-doped...
-
Non-linear circuit model of a single doubly-fed induction machine formulated in natural axes for drive systems simulation purposes
PublicationMathematical modelling and a circuit model formulated in natural axes of a single doubly-fed induction machine, with the account of magnetic circuit nonlinearity are presented in the paper. Derivation of the model differential equations was based on Lagrange's energy method. State functions of magnetic elements in the model are non-linear and depend on all currents flowing in the machine windings and on the angle of rotor position....
-
Study of the Effectiveness of Model Order Reduction Algorithms in the Finite Element Method Analysis of Multi-port Microwave Structures
PublicationThe purpose of this paper is to investigate the effectiveness of model order reduction algorithms in finite element method analysis of multi-port microwave structures. Consideration is given to state of the art algorithms, i.e. compact reduced-basis method (CRBM), second-order Arnoldi method for passive-order reduction (SAPOR), reduced-basis methods (RBM) and subspace-splitting moment-matching MOR (SSMM-MOR)
-
Heat transfer characteristics of hybrid microjet – Microchannel cooling module
PublicationThe paper presents experimental investigation of heat transfer intensification in a microjet–microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper was...
-
Comparison of heat transfer characteristics in surface cooling with boiling microjets of water, ethanol and HFE7100
PublicationThe basis of microjet technology is to produce jets which impinge the surface at the stagnation point with a very high kinetic energy. Main objective of this paper was to investigate the physical phenomena occurring on solid surfaces upon impingement of the single microjet in case of three fluids, namely water, ethanol and HFE7100. Intense heat transfer in the impact zone of microjet has been examined and described with precise...
-
Volumetric and torque efficiency of pumps during start-up in low ambient temperatures
PublicationThe volumetric, torque and total efficiency of hydraulic pumps change during start-up in low ambient temperatures, as well as in thermal shock conditions, un-til they reach the set conditions. The time to reach steady-state conditions de-pends on many parameters: ambient temperature, flow rate, fluid temperature, design of hydraulic units. The author carried out tests of hydraulic pumps in the Hydraulics Laboratory of the Faculty...
-
Numerical Test for Stability Evaluation of Discrete-Time Systems
PublicationIn this paper, a new numerical test for stability evaluation of discrete-time systems is presented. It is based on modern root-finding techniques at the complex plane employing the Delaunay triangulation and Cauchy's Argument Principle. The method evaluates if a system is stable and returns possible values and multiplicities of unstable zeros of the characteristic equation. For state-space discrete-time models, the developed test...
-
Wykorzystanie algorytmów ewolucyjnych do doboru wzmocnień rozszerzonego obserwatora prędkości maszyny indukcyjnej
PublicationW pracy opisano sposób doboru wzmocnień rozszerzonego obserwatora prędkości maszyny indukcyjnej przy wykorzystaniu algorytmów ewolucyjnych. Zaproponowano funkcję celu opartą na rozkładzie biegunów obserwatora. Ze względu na wpływ prędkości maszyny na dynamikę obserwatora zaproponowano dobór wzmocnień obserwatora dla różnych przedziałów prędkości. Dla poszczególnych przedziałów zaprezentowano wyniki doboru wzmocnień w postaci tabel...
-
Comparison of Average Energy Slope Estimation Formulas for One-dimensional Steady Gradually Varied Flow
PublicationTo find the steady flow water surface profile, it is possible to use Bernoulli’s equation, which is a discrete form of the differential energy equation. Such an approach requires the average energy slope between cross-sections to be estimated. In the literature, many methods are proposed for estimating the average energy slope in this case, such as the arithmetic mean, resulting in the standard step method, the harmonic mean and...
-
Point cloud based surface analysis of prestressed concrete element in exceeded state of serviceability
PublicationBy definition, serviceability state is characterized by the fact that despite meeting the requirements associated with carrying capacity, the object is not suitable for use. Serviceability limit state refers to factors, such as durability, overall stability, fire resistance, cracking, excessive vibration. Perfect examples of exceeded serviceability state are the improper vibration of a skyscraper, which inhabitants may suffer from...
-
Zastosowanie specjalnego uziemienia żył powrotnych w liniach kablowych SN
PublicationW artykule porównano metody uziemiania żył powrotnych kabli średniego napięcia. Głównym kryterium oceny poszczególnych rozwiązań było ograniczenie strat w przesyle energii elektrycznej oraz zapewnienie ochrony przeciwprzepięciowej osłon kabli. Na podstawie symulacji kabli zamodelowanych w programie CYMCAP i otrzymanych wyników obciążalności prądowej i strat w linii zaprezentowano metodę krzyżowania żył powrotnych (CB – cross-bonding...
-
Optimization of hydrodynamic vortex separator for removal of sand particles from storm water by computational fluid dynamics
PublicationStorm water treatment has been gradually acknowledged for the removal of pollutants from urban areas using the hydro cyclone separation technique. The separation efficiency of the hydrodynamic vortex separator (HDVS) is a complex phenomenon. With the aim enhance the separation potency of HDVS for storm runoff to get rid of sand particles, the HDVS with different structural configurations was studied by computational fluid dynamics....
-
Sound intensity distribution around organ pipe
PublicationThe aim of the paper was to compare acoustic field around the open and stopped organ pipes. The wooden organ pipe was located in the anechoic chamber and activated with a constant air flow, produced by an external air-compressor. Thus, long-term steady state response was possible to obtain. Multichannel acoustic vector sensor was used to measure the sound intensity distribution of radiated acoustic energy. Measurements have been...
-
Heat transfer characteristics of hybrid microjet -microchannel cooling module
PublicationThe paper presents the experimental investigation of heat transfer intensification in a microjet- microchannel cooling module. Applied technology takes benefits from two very attractive heat removal techniques. When jets are impinging on the surface, they have a very high kinetic energy at the stagnation point, also in microchannels boundary layer is very thin allowing to obtain very high heat fluxes. Main objective of this paper...
-
Investigating Fuel Injection Strategies to Enhance Ship Energy Efficiency in Wave Conditions
PublicationThe prediction of fuel consumption and resulting transportation costs is a crucial stage in ship design, particularly for conditions involving motion in waves. This study investigates the real-time fuel consumption of a container ship when sailing in waves. The overall ship performance is evaluated using a novel non-linear coupled hull-engine-propeller interaction model. A series of towing tank experiments for hull resistance in...
-
Hierarchical Estimation of Human Upper Body Based on 2D Observation Utilizing Evolutionary Programming and 'Genetic Memory'
PublicationNew method of the human body pose estimation based on single camera 2D observation is presented. It employs 3D model of the human body, and genetic algorithm combined with annealed particle filter for searching the global optimum of model state, best matching the object's 2D observation. Additionally, motion cost metric is employed, considering current pose and history of the body movement, favouring the estimates with the lowest...
-
The electrochemical response to glassy carbon electrode modification steps towards viral electrochemical immunosensor preparation
Open Research DataThe dataset contains the electrochemical measurements (CV/EIS) carried out for the consecutive steps of the glassy carbon GC electrode functionalization, in separate subfolders, as described. The cyclic voltammetry (CV) was conducted using a Palmsens 4 potentiostat/galvanostat system (Methrom, Autolab, Netherlands) in the standard three-electrode configuration,...
-
Adaptive Optimal Discrete-Time Output-Feedback Using an Internal Model Principle and Adaptive Dynamic Programming
PublicationIn order to address the output feedback issue for linear discrete-time systems, this work suggests a brand-new adaptive dynamic programming (ADP) technique based on the internal model principle (IMP). The proposed method, termed as IMP-ADP, does not require complete state feedback, merely the measurement of input and output data. More specifically, based on the IMP, the output control problem can first be converted into a stabilization...
-
Application of the distributed transfer function method and the rigid finite element method for modelling of 2-D and 3-D systems
PublicationIn the paper application of the Distributed Transfer Function Method and the Rigid Finite Element Method for modelling of 2-D and 3-D systems is presented. In this method an elastic body is divided into 1-D distributed parameter elements (strips or prisms). The whole body (divided into strips or prism) is described by a set of coupled partial differential equations. Solving this equations in the state space form it is possible...
-
Reliability-Based Stability Analysis of a Baltic Cliff by the Combined Response Surface Method
PublicationA simple, straightforward computational procedure was proposed, incorporating the Response Surface Method (RSM) linked with the standard Monte Carlo (MC) simulation method and the Point Estimate Method (PEM). PEM samples make it possible to analyse the sensitivity of the cliff’s stability to variation in subsoil parameters and to reduce the number of random variables of the problem. The proposed methods were tested in two cases:...
-
Fabrication and Structural Properties of LaNb 1‐x As x O 4 Ceramics
PublicationLanthanum niobate substituted with arsenic was synthesized by three methods: solid state reaction from binary oxides and two different methods combining co-precipitation and solidstate reaction. In the first of the combined methods LaNb1- xAsxO4 was synthesized from LaAsO4, obtained from coprecipitation method, and lanthanum and niobium oxides. In the second LaNbO4 was first synthesized from binary oxides and then mixed with LaAsO4...
-
Numeryczna analiza hydrauliki toru kajakarstwa górskiego w Drzewicy
PublicationW artykule zaproponowano wykorzystanie do analizy hydrodynamiki toru kajakarstwa górskiego symulacji numerycznej, wykorzystującej dwuwymiarowe równania ruchu wody w warunkach przepływu szybkozmiennego. Rozwiązanie równań hydrodynamiki wykonano samodzielnie z zastosowaniem metody objętości skończonych. Jako przykład zastosowania zaproponowanej metody przedstawiono analizę przepływu wzdłuż istniejącego, poddanego modernizacji toru...
-
Electronic transition dipole moment functions of the first singlet Sigma gerade plus state of the Lithium dimer
Open Research DataElectronic transition dipole moment functions (ETDMF) of the first singlet Sigma gerade plus (1sSg+) state have been calculated for the Lithium dimer. ETDMFs are needed in understanding processes like photodissociation, photoassociation, cooling, and trapping of molecules. The results of the five ETDMFs have been obtained by the nonrelativistic multireference...
-
Electronic transition dipole moment functions of the first triplet Sigma ungerade plus state of the Lithium dimer
Open Research DataElectronic transition dipole moment functions (ETDMF) of the first triplet Sigma ungerade plus (1tSu+) state have been calculated for the Lithium dimer. ETDMFs are needed in understanding processes like photodissociation, photoassociation, cooling, and trapping of molecules. The results of the five ETDMFs have been obtained by the nonrelativistic multireference...
-
Electronic transition dipole moment functions of the second triplet Sigma ungerade plus state of the Lithium dimer
Open Research DataElectronic transition dipole moment functions (ETDMF) of the second triplet Sigma ungerade plus (2tSu+) state have been calculated for the Lithium dimer. ETDMFs are needed in understanding processes like photodissociation, photoassociation, cooling, and trapping of molecules. The results of the five ETDMFs have been obtained by the nonrelativistic multireference...
-
Electronic transition dipole moment functions of the third singlet Sigma gerade plus state of the Lithium dimer
Open Research DataElectronic transition dipole moment functions (ETDMF) of the third singlet Sigma gerade plus (3sSg+) state have been calculated for the Lithium dimer. ETDMFs are needed in understanding processes like photodissociation, photoassociation, cooling, and trapping of molecules. The results of the five ETDMFs have been obtained by the nonrelativistic multireference...
-
Electronic transition dipole moment functions of the third triplet Sigma ungerade plus state of the Lithium dimer
Open Research DataElectronic transition dipole moment functions (ETDMF) of the third triplet Sigma ungerade plus (3tSu+) state have been calculated for the Lithium dimer. ETDMFs are needed in understanding processes like photodissociation, photoassociation, cooling, and trapping of molecules. The results of the five ETDMFs have been obtained by the nonrelativistic multireference...
-
Electronic transition dipole moment functions of the fourth triplet Sigma ungerade plus state of the Lithium dimer
Open Research DataElectronic transition dipole moment functions (ETDMF) of the fourth triplet Sigma ungerade plus (4tSu+) state have been calculated for the Lithium dimer. ETDMFs are needed in understanding processes like photodissociation, photoassociation, cooling, and trapping of molecules. The results of the five ETDMFs have been obtained by the nonrelativistic multireference...
-
Electronic transition dipole moment functions of the fourth singlet Sigma gerade plus state of the Lithium dimer
Open Research DataElectronic transition dipole moment functions (ETDMF) of the fourth singlet Sigma gerade plus (4sSg+) state have been calculated for the Lithium dimer. ETDMFs are needed in understanding processes like photodissociation, photoassociation, cooling, and trapping of molecules. The results of the five ETDMFs have been obtained by the nonrelativistic multireference...
-
Electronic transition dipole moment functions of the second singlet Sigma gerade plus state of the Lithium dimer
Open Research DataElectronic transition dipole moment functions (ETDMF) of the second singlet Sigma gerade plus (2sSg+) state have been calculated for the Lithium dimer. ETDMFs are needed in understanding processes like photodissociation, photoassociation, cooling, and trapping of molecules. The results of the five ETDMFs have been obtained by the nonrelativistic multireference...
-
Electronic transition dipole moment functions of the fifth singlet Sigma gerade plus state of the Lithium dimer
Open Research DataElectronic transition dipole moment functions (ETDMF) of the fifth singlet Sigma gerade plus (5sSg+) state have been calculated for the Lithium dimer. ETDMFs are needed in understanding processes like photodissociation, photoassociation, cooling, and trapping of molecules. The results of the five ETDMFs have been obtained by the nonrelativistic multireference...
-
Electronic transition dipole moment functions of the fifth triplet Sigma ungerade plus state of the Lithium dimer
Open Research DataElectronic transition dipole moment functions (ETDMF) of the fifth triplet Sigma ungerade plus (5tSu+) state have been calculated for the Lithium dimer. ETDMFs are needed in understanding processes like photodissociation, photoassociation, cooling, and trapping of molecules. The results of the five ETDMFs have been obtained by the nonrelativistic multireference...
-
Comparison of Cu1.3Mn1.7O4 spinels doped with Ni or Fe and synthesized via wet chemistry and solid-state reaction methods, designed as potential coating materials for metallic interconnects
PublicationThe influence of the method applied to synthesize Cu-Mn-O spinel was evaluated. The methods selected for the investigation were EDTA gel processes and solid-state reaction synthesis. From the obtained powders, sinters were prepared and assessed in terms of their properties as potential coating materials. Additionally, the influence of Ni and Fe dopants was evaluated. The results show that the EDTA gel processes method seems to...
-
Determination of pitting corrosion stage of stainless steel by galvanodynamic impedance spectroscopy
PublicationThis paper investigates the methodology for differentiation of multistep process of pitting corrosion of AISI 304 stainless steel in the environment of iron (III) chloride. Measurements were performed using Galvanodynamic Electrochemical Impedance Spectroscopy (GDEIS). Application of this methodology allowed monitoring of natural corrosion process without external current (IDC = 0A) nor potential perturbation of the system. Applied...
-
Experimental Verification of the CFD Model of the Squeeze Film Lifting Effect
PublicationAbstract: The presented study shows the results of the research into the squeeze film levitation phenomena. The system introduced in the investigation is composed of a vibrating surface, air squeeze film, and the surface of the body freely suspended over the film. The use of the CFD (Computational Fluid Dynamics) model used in the system allows us to determine the steady state, periodic behavior of the air film (described by Navier–Stokes,...
-
Can sodium 1-alkylsulfonates participate in the sodium dodecyl sulfate micelle formation?
PublicationThe aggregation behavior of sodium dodecyl sulfate (SDS) was studied in an aqueous solution in the presence of increasing concentrations of selected sodium 1-alkylsulfonates, namely sodium 1-octanesulfonate, sodium 1-decanesulfonate, and sodium 1-dodecanesufonate. The critical micelle concentration (CMC) of SDS was determined by conductivity and fluorescence intensity measurements. The steady-state fluorescence quenching experiments...
-
Performance of the PEM fuel cell module. Part 2. Effect of excess ratio and stack temperature
PublicationThe paper describes a fuel cell based system performance under different thermal conditions. The system could be fed with bottled hydrogen or with very high purity hydrogen obtained from reforming of methanol. The system is based on two fuel cell units (1.2 kW each, produced by Ballard Power Systems Inc. and called Nexa), DC/DC converter, DC/AC inverter, microprocessor control unit, load unit, bottled hydrogen supply system and...