displaying 1000 best results Help
Search results for: SLIDING CONTACT TEMPERATURE
-
Measurement of the temporal and spatial temperature distribution on the surface of PVCP tissue phantom illuminated by laser.
Open Research DataApplication of laboratory set-up for characterisation of thermal properties of optical tissue phantoms during laser irradiation is presented. The produced system utilizes thermographic camera VIGOcam v50 and dermatological laser system with a 975 nm diode laser module. The set-up was used to perform measurements of the temporal and spatial temperature...
-
High temperature corrosion resistance of porous hastelloy alloy
PublicationTo further understand the suitability of Ni-Cr-base alloy for solid oxide fuel cell (SOFC), a commercial Ni-Cr-Fe-Mo alloy, Hastelloy X was selected and evaluated for oxidation behaviour under high temperature conditions. HastelloyX was chosen due to its unusual resistance to oxidizing, reducing and neutral atmospheres. For long term stability of metal supported fuel cell, the corrosion resistance plays a vital role and must be...
-
Temperature influence on tire/road noise evaluated by the drum method
PublicationAmbient air and road surface temperatures substantially affect the road vehicle noise emission. The temperature influence on tire/road noise depends mainly on tire-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tires. The correction procedures for temperature effect are still under consideration and preparation. Laboratory experiment was prepared to...
-
Spatial distribution of CO2, O2, CO, NO and temperature within a biowaste composting pile
Open Research DataThe dataset contains the color-coded isophlets illustrating the spatial distribution of gas concentrations (CO, CO2, O2 and NO) and the temperature in biowaste composting pile during 6 weeks of process. Four cross sections and two longitudinal cross sections (the left and right sides of the pile) were made using Surfer 10 software (Golden Software,...
-
The Influence of Workpiece Hardness on Plate Temperature during One Side Lapping
PublicationLapping leads to a surface with low roughness and high precision. Because of required parts accuracy tool flatness is the key to the successful machining. To avoid its excessive thermal expansion, plate temperature research was taken. The goal was to determine the correlation between the basic lapping conditions and wheel temperature. In work Bulsara et al. authors developed model to estimate the maximum and average temperature...
-
Multi Parameter Sliding Test Result Evaluation for The Selection of Material Pair for Wear Resistant Components of a Hydraulic motor Dedicated for Use With Environmentally Friendly Working Fluids
PublicationIn the paper the method and results are presented of the testing of tribological performance of a number of hard materials available commercially. The tests consisted in unidirectional sliding with liquid lubrication. The load and velocity regime chosen were similar to a standard four-ball lubricity test with constant velocity and load increasing over time. The regime was modified in such a way that over the initial part of the...
-
A study of separation by the direct-contact membrane distillation process
Publication -
Probable allergic contact dermatitis mimicking erythema muliforme
Publication -
The reactions occuring on the implant as a result of contact with human tissue
PublicationObecnosc implantu w ciele czlowieka powoduje liczne, czesto nieprzewidywalne skutki. Powodem takiej sytuacji jest duza roznorodnosc interakcji materialu medycznego z kontaktujaca sie z nim tkanka. Stwierdzenie to dotyczy glownie oddzialywan i skutkow zachodzacych na poziomie molekularnym w poszczegolnych komorkach kontaktujacej sie tkanki.
-
The Rolling Contact Fatigue of PVD Coated Spur Gears
Publication -
Application of Infrared Thermography to Non-Contact Testing of Varistors
Publication -
Equilibration Time of Solid Contact Ion-Selective Electrodes
Publication -
Verification of multiband system for non-contact emissivity measurements
PublicationW pracy przeprowadzono weryfikację wielopasmowej pasywnej metody pomiaru emisyjności obiektu na drodze eksperymentalnej. W oparciu o zrealizowane stanowisko pomiarowe dokonano pomiarów emisyjności wybranych obiektów. Uzyskano dobrą zgodność wyników pomiarów z wynikami wcześniejszej komputerowej analizy systemu. Potwierdziło to przydatność wielopasmowej metody do pomiaru emisyjności w warunkach roboczych.
-
Simultaneous measurements of ECG, body Impedance and temperature
Open Research DataThe data are complementary part of the experiment designed to demonstrate how to use the network protocols to transmit medical data. The dataset contains biomedical signals of ECG, Impedanc and temperature acquired simultaneously. The data allow students to become familiar with data acquisition methods (simulate data transmission by medical device over...
-
The selected effects of high temperature air-steam mixture wood drying
PublicationThe results of properties change of beech wood after drying process are presented. The wood taken to experiments was from northern part of Pomeranian region in Poland. Before the main high temperature drying process using air-steam mixture, wood was initially dried in an open air conditions. The high temperature drying process was conducted at temperature 120oC, humidity 48%, flow rate of drying medium 2.5m/s and atmospheric pressure....
-
Analysis of diagnostic informativeness of the exhaust temperature of a naval gas turbine
PublicationThe conducted investigations aimed to carry out an analysis of the possibility that the failures identification in the automatic control system of a gas turbine engine could be worked out on the basis of measurements of the exhaust stream temperature behind the gas generator. The exhaust temperature represents a basic control parameter, enabling technical state evaluation of the engine within the operation process, which is observed...
-
New Simple and Robust Method for Determination of Polarity of Deep Eutectic Solvents (DESs) by Means of Contact Angle Measurement
PublicationThe paper presents a new method for evaluating the polarity and hydrophobicity of deep eutectic solvents (DESs) based on the measurement of the DES contact angle on glass. DESs consisting of benzoic acid derivatives and quaternary ammonium chlorides–tetrabutylammonium chloride (TBAC) and benzyldimethylhexadecylammonium chloride (16-BAC)—in selected molar ratios were chosen for the study. To investigate the DESs polarity, an optical...
-
Temperature-dependent structure-property modeling of viscosity for ionic liquids
PublicationIn this paper we present the methodology for assessing the ionic liquids' viscosity at six temperature points (25, 35, 45, 50, 60 and 70 [C]), which utilizes only the in silico approach. The main idea of such assessment is based on the "correction equation" describing the correlation between experimentally measured viscosity and theoretically derived density (calculated with use of molecular mechanics), given at 6 different temperature...
-
Extended phase diagram of RNiC2 family: Linear scaling of the Peierls temperature
PublicationPhysical properties for the late-lanthanide-based RNiC2 (R = Dy, Ho, Er, and Tm) ternary compounds are reported. All the compounds show antiferromagnetic ground state with the Néel temperature ranging from 3.4 K for HoNiC2 to 8.5 K for ErNiC2. The results of the transport and galvanomagnetic properties confirm a charge density wave state at and above room temperature with transition temperatures TCDW = 284, 335, 366, and 394 K for...
-
Improvement of Oxygen Electrode Performance of Intermediate Temperature Solid Oxide Cells by Spray Pyrolysis Deposited Active Layers
PublicationIntermediate temperature solid oxide fuel cells oxygen electrodes are modified by active interfacial layers. Spray pyrolysis is used to produce thin (≈500 nm) layers of mixed ionic and electronic conductors: Sm0.5Sr0.5CoO3−δ (SSC), La0.6Sr0.4CoO3−δ (LSC), La0.6Sr0.4Co0.2Fe0.8O3−δ (LSCF), and Pr6O11 (PrOx) on the electrode–electrolyte interface. The influence of the annealing temperature on the electrode polarization (area specific...
-
High temperature corrosion evaluation and lifetime prediction of porous Fe22Cr stainless steel in air in temperature range 700–900 °C
PublicationThis work describes a high temperature corrosion kinetics study of ~30% porous Fe22Cr alloys. The surface area of the alloy (~0.02 m2 g-1) has been determined by tomographic microscopy. The weight gain of the alloys was studied by isothermal thermogravimetry in the air for 100 hours at 700 - 900 °C. Breakaway oxidation was observed after oxidation at 850 °C (~100 hours) and 900 °C (~30 hours). The lifetime prediction shows the...
-
On the differential effect of temperature on the Nusselt-Rayleigh relationship in free convection
PublicationThe aim of and inspiration behind this paper was to explain the reasons, also observed by other researchers, of the discrepancy in the results of experimental free convection, which for small Rayleigh and Nusselt numbers in the initial phase of research can sometimes reach several hundred percent. These discrepancies decrease with increasing heating power and plate surface temperature, in proportion to the increase in Ra and Nu,...
-
Comparative wear test of journal sliding bearings with sintered bronze and Babbitt alloy bushes lubricated by environmentally acceptable/adapted lubricants (EAL)
PublicationA growing awareness of the negative effects of mineral oils on the natural environment has resulted in the introduction of new regulations related to environmental protection. One of these regulations requires the use of environmentally acceptable/adapted lubricants (EAL) to lubricate marine main shaft bearings, in place of the mineral lubricating oils that have been used for decades. Classification Societies, which supervise...
-
Impact of low-temperature sintering on the Fe-based amorphous coatings
PublicationBulk metallic glasses (BMGs) have gained a lot of attention in recent years due to their outstanding properties such as high hardness and excellent wear and corrosion resistance. However, they are restricted in industrial applications due to their extreme brittleness. Iron based amorphous coatings from BMGs are the best solution to use them by overcoming the problem of extreme brittleness. The coatings can be sprayed by various...
-
Influence of the low ambient temperature on the start-up process of hydraulic pumps
PublicationStarting hydraulic pumps in low ambient temperatures may cause: decreased hydraulic-mechanical efficiency, larger vibration of hydraulic installation, faster wear and more frequent damage to the elements of pumps, change of material properties of elements, increase of pressure drop. As a result of pressure drop in the suction pipe, large underpressure may be experienced, causing incomplete filling of pump working chambers with...
-
A Theoretical and Experimental Study of Moderate Temperature Alfa Type Stirling Engines
PublicationThe Stirling engine is a device that allows conversion of thermal energy into mechanical energy with relatively high efficiency. Existing commercial designs are mainly based on the usage of high temperature heat sources, whose availability from renewable or waste heat sources is significantly lower than that of moderate temperature sources. The paper presents the results of experimental research on a prototype alpha type Stirling...
-
Investigation of the temperature modulation parameters on semiconductor gas sensor response
PublicationIn this work we present the results of the investigation of the sensing properties of semiconductor gas sensors with a sinusoidally modulated temperature in the presence of synthetic air (SA) and three volatile air pollutants, i.e. NH3, NO2 and SO2. The measurements were performed for different average sensor heater temperatures and the amplitude of the modulation signal. In addition, the extraction of features from the sensor...
-
Numerical simulation of temperature distribution of heat flow on reservoir tanks connected in a series
PublicationThe flow of temperature distribution through a medium in thermodynamic studies plays an important role in understanding physical phenomena in chemical science and petroleum engineering, while temperature distribution indicates the degree of reaction that must be undergone to obtain the final product. Therefore, this paper aims to present and apply the exponential matrix algorithm (EMA), differential transformation algorithm (DTA),...
-
The effect of the temperature change rate on determination of the criticalpitting temperature of stainless steels
PublicationPrzedstawiono wyniki badań wpływu szybkości zmian temperatury na wyznaczaną krytyczną temperaturę korozji wżerowej. Badania stali 316L przeprowadzono metodą termometrii cyklicznej. Stwierdzono, że zwiększenie szybkości zmian temperatury związane jest ze zwiększeniem wyznaczonej temperatury krytycznej. Zależność krytycznej temperatury korozji wżerowej od szybkości korozji ma charakter liniowy. Wartości krytycznej temperatury korozji...
-
Performance of the very high-temperature heat pump with low GWP working fluids
PublicationTraditional heat pumps are a very attractive pro-ecological solutions for a number of applications, including providing of heating or heat recovery from industrial processes. The application range of heat pumps could be greatly enlarged when the operating temperature would be increased to 130-150°C and/or the temperature lift can be increased to 50-100 K. In the paper, the very high temperature vapour-compressor based single stage...
-
Influence of CeO2 and TiO2 Particles on Physicochemical Properties of Composite Nickel Coatings Electrodeposited at Ambient Temperature
PublicationThe Ni-TiO2 and Ni-CeO2 composite coatings with varying hydrophilic/hydrophobic characteristics were fabricated by the electrodeposition method from a tartrate electrolyte at ambient temperature. To meet the requirements of tight regulation by the European Chemicals Agency classifying H3BO3 as a substance of very high concern, Rochelle salt was utilized as a buffer solution instead. The novelty of this study was to implement a...
-
Concrete temperature measurements of cubic specimens cured under isothermal and semi-adiabatic conditions
Open Research DataThe DataSet contains temperature measurements of concrete cubes (150 x 150 x 150 mm) cured under isothermal and semi-adiabatic conditions. The specimens were moulded from six types of concrete mixtures produced in the laboratory conditions. Mix #1: Portland cement CEM I 42.5R and gravel aggregate, mix #2: CEM I 42.5R and basalt aggregate, mix#3: Portland-composite...
-
ZnO ALD-Coated Microsphere-Based Sensors for Temperature Measurements
PublicationIn this paper, the application of a microsphere-based fiber-optic sensor with a 200 nm zinc oxide (ZnO) coating, deposited by the Atomic Layer Deposition (ALD) method, for temperature measurements between 100 and 300°C, is presented. The main advantage of integrating a fiber-optic microsphere with a sensing device is the possibility of monitoring the integrity of the sensor head in real-time, which allows for higher accuracy during...
-
INFLUENCE OF TEMPERATURE ON THE ACTIVITY OF ANAMMOX GRANULAR BIOMASS - SHORT AND LONG-TERM ASPECT
PublicationThe aim of this study was to determine a short-term and long-term effect of temperature on the anammox process rate and determination of temperature coefficients in the Arrhenius and Ratkowski equations. The short-term effects of temperature on the anammox biomass were investigated in batch tests at ten different temperatures in the range of 10-55 ̊C. The maximum rate 1.3 gN (gVSS·d)-1 observed at 40 ̊C. The minimum rate, close...
-
Signal filtering method of the fast-varying diesel exhaust gas temperature
PublicationThe paper presents the problem of the impact of external distortions originating on laboratory test stands on the results of measurements of fast-varying diesel exhaust gas temperature. It has been stressed how significant the aspect of the test stand adaptation is during an experiment to ensure the smallest possible impact. This paper, however, focuses on the methods of mathematical processing of a signal recorded during experimental...
-
The effect of elevated temperature on LCF damage growth in 2024AA – Experiment and modeling
PublicationThis paper presents the results of experimental low-cycle fatigue (LCF) tests conducted on EN-AW 2024 alloy in T3511 temper at 100 ◦C, 200 ◦C and 300 ◦C. The material’s basic fatigue characteristics were determined, such as fatigue life curve and cyclic strain curve. Both the hysteresis loop and nature of fracture surfaces obtained in macro- and microscopic observations (scanning electron microscope, SEM) were accounted for. The...
-
Field Evaluation of High Modulus Asphalt Concrete Resistance to Low-Temperature Cracking
PublicationHigh-modulus asphalt concrete has numerous advantages in comparison to conventional asphalt concrete, including increased resistance to permanent deformations and increased pavement fatigue life. However, previous studies have shown that the construction of road pavements with High Modulus Asphalt Concrete (HMAC) may significantly increase the risk of low-temperature cracking. Those observations were the motivation for the research...
-
Sea surface temperature distribution during upwelling along the Polish Baltic coast
PublicationAmong over 150 maps of sea surface temperature in the Polish Baltic coastal region derived from satellite data during the warm period of the year (April-October) in 2000-2002, 41 cases were noted where its distribution showed characteristic features indicating the occurrence of coastal upwelling. The fundamental parameters of range, probability of occurrence and temperature modification caused by water from deeper sea layers...
-
High Temperature Air Combustion and Gasification (HTAC; HTAG)
PublicationCombustion and gasification technology utilizing high-cycle regenerative air/steam preheater has drawn increased attention in many application areas. The process is to be realized at temperature level above ash melting point using highly preheated agent. The use of highly preheated media above 900oC provides additional energy in to conversion processes and results in considerable changes to the design of combustion and gasification...
-
Investigation of the Effects of Tool Positioning Factors on Peak Temperature in Dissimilar Friction Stir Welding of AA6061-T6 and AA7075-T6 Aluminum Alloys
PublicationAmong the emerging new welding techniques, friction stir welding (FSW) is used frequently for welding high-strength aluminum alloys that are difficult to weld by conventional fusion-welding techniques. This paper investigated the effects of tool-positioning factors on the maximum temperature generated in the dissimilar FSW joint of AA6061-T6 and AA7075-T6 aluminum alloys. Three factors of plunge depth, tool offset, and tilt angle...
-
Effect of Temperature and Nanoparticle Concentration on Free Convective Heat Transfer of Nanofluids
PublicationA theoretical analysis of the influence of temperature and nanoparticle concentration on free convection heat transfer from a horizontal tube immersed in an unbounded nanofluid was presented. The Nusselt (Nu) number and heat transfer coefficient were parameters of the intensity of the convective heat transfer. For free convection, the Nu number was a function of the Rayleigh (Ra) number and Prandtl (Pr) number. The Rayleigh (Ra)...
-
Analysis of unsteady flow forces on the thermowell of steam temperature sensor
PublicationIn this paper, 3D numerical analysis of unsteady flow forces acting on the measuring sheath of steam temperature is presented. According to that purpose, the CFD (Computation Fluid Dynamic [1]) approach has been used. The nonstationary of fluid acting on the measuring sheath such as: Strouhal frequency, amplitude of pressure, structure of vortex, peak of pressure, field of pressure, field of velocity etc. are studied analytically...
-
The Effect of Calcination Temperature on Structure and Photocatalytic Properties of WO3/TiO2 Nanocomposites
PublicationSeries ofWO3/TiO2 nanocompositeswere obtained by hydrothermal method followed by calcination in the temperature range from 400∘C to 900∘C. The characteristics of photocatalysts by X-ray diffractometry (XRD), scanning electron microscope (SEM), and diffuse reflectance spectroscopy (DRS) showed that increasing the calcination temperature from 400 to 900∘C resulted in change of photocatalytic activity under UV-Vis light.Moreover,...
-
Proton Conducting Ceramic Powder Synthesis by a Low Temperature Method
PublicationMolten salt synthesis (MSS) is a simple method for the preparation of ceramic powders with specific morphology. The main role of the molten salts is to increase the reaction rate and lower the reaction temperature. It occurs because of much higher mobility of reactants in the liquid medium than in the solid state. In this work the molten salt synthesis was applied to produce ceramic powders of La0995Ca0005NbO4 and BaCe09−xZrxY01O3....
-
Numerical analysis of high temperature minichannels heat exchanger performance
PublicationNowadays, the most difficult technological challenge in energy sector is connected with the gas micro-CHP units, dedicated to the distributed power generation. They are expected to be of high efficiency and at the same time of compact in size. Regarding the first reason, significant increase in microturbine efficiency can only be achieved by increase in the engine operating temperature. Therefore, one of the critical elements in...
-
Closed Form Constraint Equations Used to Express Frictionless Slip of Multibody Systems Attached to Finite Elements—Application to a Contact between a Double Pendulum and a Beam
PublicationThis paper focuses on the numerical modeling of the dynamics of mechanical systems. Robots that can inspect high-voltage lines inspired this research. Their control systems must anticipate potential grab positions appropriately. We intend to formulate equations dedicated to the numerical description of the robot/cable contact. The investigated problem is not straightforward, since parts of the modeled systems are numerically inhomogeneous....
-
Evaluation of Asphalt Mixture Low-Temperature Performance in Bending Beam Creep Test
PublicationLow-temperature cracking is one of the most common road pavement distress types in Poland. While bitumen performance can be evaluated in detail using bending beam rheometer (BBR) or dynamic shear rheometer (DSR) tests, none of the normalized test methods gives a comprehensive representation of low-temperature performance of the asphalt mixtures. This article presents the Bending Beam Creep test performed at temperatures from −20...
-
Contact angle of the ferronanofluid and influence of the magnetic field on the drying droplet
Publication -
Contact problems in lock gates in view of investigation and field experience
PublicationW artykule przedstawiono ogólny przegląd zagadnień kontaktowych zamknięć wodnych. Szczególną uwagę zwrócono na siły kontaktowe, zagadnienia trybologiczne i inne o dużym znaczeniu mające wpływ na projektowanie i eksploatację elementów kontaktowych i na całość elementów kontaktowych zapewniających stateczność całego układu zamknięć wodnych. Podano wyniki badań w laboratorium symulujących pracę zamknięć. Zaproponowano nowe rozwiązania...
-
Numerical modeling of force and contact networks in fragmented sea ice
Publication