Search
displaying 1000 best results Help
Search results for: POLYMER-MATRIX COMPOSITE
-
A Novel Coupling Matrix Synthesis Technique for Generalized Chebyshev Filters With Resonant Source–Load Connection
PublicationThis paper reports a novel synthesis method for microwave bandpass filters with resonant source–load connection. In effect, a network realizing N+1 transmission zeros (where N is the number of reflection zeros) is obtained. The method is based on a prototype transversal coupling matrix (N+2, N+2) with source and load connected by a resonant circuit formed by a capacitor in parallel with a frequency-invariant susceptance. To complement...
-
The Conceptual Research over Low-Switching Modulation Strategy for Matrix Converters with the Coupled Reactors
PublicationIn this paper, different Pulse Width Modulation (PWM) strategies for operating with a low-switching frequency, a topology that combines Conventional Matrix Converters (CMCs), and Coupled Reactors (CRs) are presented and discussed. The principles of the proposed strategies are first discussed by a conceptual analysis and later validated by simulation. The paper shows how the combination of CMCs and CRs could be of special interest...
-
Systems of differential equations with a singular matrix
PublicationPraca dotyczy układów równań różniczkowych z macierzą osobliwą. Szczególnymi przypadkami takich układów są równania różniczkowo-algebraiczne. Korzystając z odpowiedniej nierówności różniczkowej dla układów równań i metody quasi linearyzacji pokazano, iż odpowiednie monotoniczne ciągi są zbieżne do rozwiązania naszego problemu i jest to zbieżność kwadratowa. O funkcji f występującej po prawej stronie zagadnienia zakładano...
-
Health matrix (Cleveland, Ohio : 1991)
Journals -
SIAM JOURNAL ON MATRIX ANALYSIS AND APPLICATIONS
Journals -
Potential applications of crude glycerol in polymer technology–Current state and perspectives
PublicationThe increasing use of bio-based fuels and fuel additives, among them biodiesel, causes significant surplus of crude glycerol on the market which creates new challenges in terms of its sustainable utilization. A lot of ways for the incorporation of this by-product into different branches of industry requires purification by expensive and complicated processes. Therefore, researchers are seeking for applications of untreated crude...
-
Shaking table experimental study on the effectiveness of polymer bearings for seismic isolation of structures
PublicationSeismic isolation has been recognised to be a very effective way of protecting structures from damage during earthquakes. It allows us to extend the natural period of the structure and therefore avoid resonance with the ground motion. Moreover, by increasing damping in the isolation devices, more energy can be dissipated and thus the structural response can be further reduced. The aim of this paper is to show the results of the...
-
Coffee silverskin as a potential bio-based antioxidant for polymer materials: Brief review
PublicationCoffee silverskin is one of the by-products generated by the coffee industry. Although it is not the most burdensome one, because it stands only for ~4.2 wt % of coffee, it seems like an auspicious raw material for industrial processes. Coffee silverskin is characterized by a relatively low moisture content of ~5–7%, so it often does not require quite energy-consuming drying processes. The chemical composition of coffee silverskin,...
-
Coffee Wastes as Sustainable Flame Retardants for Polymer Materials
PublicationDevelopment of green flame retardants has become a core part of the attention of material scientists and technologists in a paradigm shift from general purpose to specific sustainable products. This work is the first report on the use of coffee biowastes as sustainable flame retardants for epoxy, as a typical highly flammable polymer. We used spent coffee grounds (SCG) as well as SCG chemically modified with phosphorus (P-SCG)...
-
A New Approach to the PWM Modulation for the Multiphase Matrix Converters Supplying Loads with Open-End Winding.
PublicationThis article presents three variants of the Pulse Width Modulation (PWM) for the Double Square Multiphase type Conventional Matrix Converters (DSM-CMC) supplying loads with the open-end winding. The first variant of PWM offers the ability to obtain zero value of the common-mode voltage at the load's terminals and applies only six switches within the modulation period. The second proposal archives for less Total Harmonic Distortion...
-
Investigation of solid polymer electrolyte gas sensor with different electrochemical techniques
PublicationIn this work solid polymer electrolyte (SPE) amperometric sulphur dioxide sensor is investigated. Nafion was used as a membrane electrode and 1M sulphuric acid as an internal electrolyte. Sensor response to sulphur dioxide was measured. Besides traditional constant voltage amperometry also different electrochemical techniques were used. Results obtained by these methods are compared.
-
Computations of critical load value of composite shell with random geometric imperfections
PublicationThe work presents the numerical analysis of composite shell with geometric imperfections subjected to compression along its generatrix. The imperfections are described as single indentations and random fields with random parameters of shape and correlation. The fields are generated with the use of the authors made program. Using the authors’ FEM software as well as commercial package Femap with NX Nastran, the critical load values...
-
Fabrication methods of smart composite coatings - review
PublicationPostoperative bacterial infections are one of the main reasons for unsuccessful implantation of long-term implants. The development of bacterial infection requires antibiotic therapy, in extreme cases a reimplantation procedure is necessary. In order to provide materials for implants with antibacterial properties, they are subjected to modifications to create a coating that will release the drug substance, when the inflammation...
-
Composite 2D Material-Based Pervaporation Membranes for Liquid Separation: A Review
PublicationToday, chemistry and nanotechnology cover molecular separations in liquid and gas states by aiding in the design of new nano-sized materials. In this regard, the synthesis and application of two-dimensional (2D) nanomaterials are current fields of research in which structurally defined 2D materials are being used in membrane separation either in self-standing membranes or composites with polymer phases. For instance, pervaporation...
-
New matrix-free reference material for ethene in the form of optical fibres
PublicationReference materials are indispensable in the qualitycontrol and quality assurance of analytical measurements. Onenovel approach to the generation of standard gaseous mixturesof toxic, reactive, volatile, labile, and malodorous substancesinvolves thermal decomposition or rearrangement, under definedtemperature conditions, of compounds immobilized, bychemical bonding, on the surface of an appropriate carrier torelease specific amounts...
-
Mechanics of Advanced Composite Structures
Journals -
JOURNAL OF THERMOPLASTIC COMPOSITE MATERIALS
Journals -
Effect of low-temperature plasma on chitosan-coated PEEK polymer characteristics
Publication -
Properties of New Composite Materials Based on Hydroxyapatite Ceramic and Cross-Linked Gelatin for Biomedical Applications
PublicationThe main aim of the research was to develop a new biocompatible and injectable composite with the potential for application as a bone-to-implant bonding material or as a bone substitute. A composite based on hydroxyapatite, gelatin, and two various types of commercially available transglutaminase (TgBDF/TgSNF), as a cross-linking agent, was proposed. To evaluate the impacts of composite content and processing parameters on various...
-
TESTING CONTRACTION AND THERMAL EXPANSION COEFFICIENT OF CONSTRUCTION AND MOULDING POLYMER COMPOSITES
PublicationThe paper presents results of systematic tests of contraction and thermal expansion coefficients of materials based on polymer composites. The information on the above material properties is essential both at the design stage and during the use of finished products. Components for the samples were selected in such a way as to represent typical materials used for production of construction and moulding elements. The performed tests...
-
Matrix-based robust joint fingerprinting and decryption method for multicast distribution of multimedia
PublicationThis paper addresses the problem of unauthorized redistribution of multimedia content by malicious users (pirates). The solution proposed here is a new joint fingerprinting and decryption method which meets the requirements for both imperceptibility and robustness of fingerprints and scalability in terms of design and distribution of fingerprinted multimedia content. The proposed method uses a simple block cipher based on matrix...
-
Performance of a single layer fuel cell based on a mixed proton-electron conducting composite
PublicationMany of the challenges in solid oxide fuel cell technology stem from chemical and mechanical incompatibilities between the anode, cathode and electrolyte materials. Numerous attempts have been made to identify compatible materials. Here, these challenges are circumvented by the introduction of a working single layer fuel cell, fabricated from a composite of proton conducting BaCe0.6Zr0.2Y0.2O3-δ and a mixture of semiconducting...
-
JMATRIX - a package for relativistic J-matrix calculations in elastic scattering of electrons from model potentials
PublicationWe present a software package JMATRIX, consisting of two computer codes written in FORTRAN 95 and parallelized with OpenMP, implementing the so-called J-matrix method, applied to elastic scattering of electrons on the radial potential, vanishing faster than Coulomb one. In the J-matrix method, physical scattering problem is replaced by using well-defined model, which is solved analytically. Presented software implements both non-relativistic...
-
Investigation of energy deposition and its optical imaging in polymer gel dosimeters
PublicationThis following chapter describes methods for verifying the absorbed dose during radiotherapy. Special attention is paid to the method using polymer-gel dosimeters, the dose reading of which is performed by means of Laser Computed Tomography. The chapter also includes considerations on alternative solutions for dosimetric measurements and various types of radiotherapy and their pros and cons. In addition, both the methods of structural...
-
A Generalized Framework Towards Structural Mechanics of Three-layered Composite Structures
PublicationThree-layered composite structures find a broad application. Increasingly, composites are being used whose layer thicknesses and material properties diverge strongly. In the perspective of structural mechanics, classical approaches to analysis fail at such extraordinary composites. Therefore, emphasis of the present approach is on arbitrary transverse shear rigidities and structural thicknesses of the individual layers. Therewith...
-
Modeling of Composite Shells in 6-Parameter Nonlinear Theory with Drilling Degree of Freedom
PublicationWithin the framework of a 6-parameter nonlinear shell theory, with strain measures of Cosserat type, constitutive relations are proposed for thin elastic composite shells. The material law is expressed in terms of five engineering constants of classical anisotropic continuum plus an additional parameter accounting for drilling stiffness. The theory allows for unlimited displacements and rotations. A number of examples are presented...
-
A facile approach to fabricate load-bearing porous polymer scaffolds for bone tissue engineering
PublicationBiodegradable porous scaffolds with oriented interconnected pores and high mechanical are load-bearing biomaterials for bone tissue engineering. Herein, we report a simple, non-toxic, and cost-effective method to fabricate high-strength porous biodegradable scaffolds, composed of a polymer matrix of polycaprolactone (PCL) and water-soluble poly (ethylene oxide) (PEO) as a sacrificial material by integrating annealing treatment,...
-
Effect of porosity on physical properties of lightweight cement composite with foamed glass aggregate
PublicationThis paper reports on a study of physical properties of lightweight cement composite. We investigate the possibility of replacing traditional aggregate with Granulated Ash Aggregate (GAA) and above all with Granulated Expanded Glass Aggregate (GEGA). For this purpose, 15 specimens of different percentage share of each aggregate in total aggregate volume were tested: 0%, 25%, 50%, 75% or 100% of foam glass aggregate (GEGA) partially...
-
Influence of the Addition of Recycled Aggregates and Polymer Fibers on the Properties of Pervious Concrete
PublicationThe aim of the study was to check the possibility of reusing aggregate from recycled concrete waste and rubber granules from car tires as partial substitution of natural aggregate. The main objective was to investigate the effects of recycled waste aggregate modified with polymer fibers on the compressive and flexural strength, modulus of elasticity and permeability of pervious concrete. Fibers with a multifilament structure and...
-
COMPOSITE FOOTBRIDGE - SYNERGY EFFECT IN COOPERATION BETWEEN UNIVERSITIES AND INDUSTRY
PublicationPaper presents conditions of science and industry cooperation in Poland (restrictions, barriers, good practice). A key role in initiation of collaboration between units has financial support. What is also important, it is much easier to create innovative solutions on the base of combining the potential of individuals. That is why many countries all over the world look for innovative solutions using budget funds to support grants...
-
The use of Response Surface Methodology for reliability estimation of composite engineering structures
PublicationStability loss is one of the key issues in the analysis of shells made of composite materials. This paper aims at finding the variation of the critical or limit value of the load resulting from geometric imperfections. An axially compressed 16-layer cylindrical panel model is considered. The imperfections of the panel are simulated as random fields. The parameters of these fields are used as the basic variables of the reliability...
-
Sensitivity analysis in design process of sandwich U-shaped composite footbridge
PublicationThe structure of the sandwich composite footbridge of a 14 metre span length and U-shaped cross-section was analysed. Sensitivity analysis was performed to support the design process of this innovative object. Linear discrete sensitivity analysis was performed by means of finite element method. The influence of vari-ation of several design variables i.e. thicknesses of inner and outer laminates on the mid-span deflection, as-sumed...
-
Polymer Chemistry
Journals -
Chitosan-coated coconut shell composite: A solution for treatment of Cr(III)-contaminated tannery wastewater
PublicationTannery industry generates a large amount of Cr(III)-contaminated wastewater daily. Unless properly treated, not only this effluent contaminates the water body, but also damages the environment and threatens public health. This batch study investigates the feasibility of chitosan-coated coconut shells as a low-cost material for removing Cr(III) from tannery wastewater. Both chitosan and coconut shell (CS) waste are abundantly available...
-
Interferometric Sensor of Wavelength Detuning Using a Liquid Crystalline Polymer Waveplate
PublicationOperation of a polarization interferometer for measurement of the wavelength changes of a tunable semiconductor laser was investigated. A lambda/8 waveplate made from liquid crystalline polymer is placed in one of interferometers’ arms in order to generate two output signals in quadrature. Wavelength was measured with resolution of 2 pm in the wavelength range 628–635 nm. Drift of the interferometer, measured in the period of 500...
-
Structural Health Monitoring of Composite Shell Footbridge for Its Design Validation
PublicationThe paper presents the structural health monitoring system of the composite bridge for pedestrians and cyclists. The footbridge was designed and manufactured within the FOBRIDGE project. It is the first bridge in the world, which is classified as a consistent single element structural girder, made of sandwich shells, entirely produced in a single cycle. The developed structural health monitoring system, supported design process,...
-
Direct modulation for conventional matrix converters using analytical signals and barycentric coordinates
PublicationThis paper proposes the generalized direct modulation for Conventional Matrix Converters (CMC) using the concept of analytical signals and barycentric coordinates. The paper proposes a novel approach to the Pulse Width Modulation (PWM) duty cycle computing, which allows faster prototyping of direct control algorithms. The explanation of the new idea using analytical considerations demonstrating the principles of direct voltage...
-
Polarization interferometer using a Liquid Crystalline Polymer waveplate for wavelength measurement
PublicationA two-beam polarization interferometer for measuring wavelength changes of a tunable semiconductor laser was designed, built and tested. This interferometer uses a λ/8 waveplate made from Liquid Crystalline Polymer in order to generate two output signals in quadrature. The λ/8 waveplate can be manufactured either on a beamsplitter face or on the mirror surface, reducing the cost and complexity of the optomechnical assembly. Experiment...
-
Construction and investigation of SO2 amperometric sensor with a solid polymer electrolyte membrane
Publicationn this paper a sensor for detection of the sulphur dioxide based on three electrode cell configuration with a liquid electrolyte, a mercury sulphate reference electrode and a solid polymer electrolyte working electrode is presented. Working elec- trode was obtained by using Takenaka-Torikai chemical deposi- tion method by precipitation of Au particles into the pores of the Nafion membrane. Sensors characteristics measurements were...
-
Application of Bladder Acellular Matrix in Urinary Bladder Regeneration: The State of the Art and Future Directions
PublicationConstruction of the urinary bladder de novo using tissue engineering technologies is the “holy grail” of reconstructive urology. The search for the ideal biomaterial for urinary bladder reconstruction has been ongoing for decades. One of the most promising biomaterials for this purpose seems to be bladder acellular matrix (BAM). In this review we determine the most important factors, which may affect biological and physical properties...
-
M-integral for finite anti-plane shear of a nonlinear elastic matrix with rigid inclusions
PublicationThe path-independent M-integral plays an important role in analysis of solids with inhomogeneities. However, the available applications are almost limited to linear-elastic or physically non-linear power law type materials under the assumption of infinitesimal strains. In this paper we formulate the M-integral for a class of hyperelastic solids undergoing finite anti-plane shear deformation. As an application we consider the problem...
-
Potential applications of by-products from the coffee industry in polymer technology – Current state and perspectives
PublicationCoffee is one of the most popular beverages in the world, and its popularity is continuously growing, which can be expressed by almost doubling production over the last three decades. Cultivation, processing, roasting, and brewing coffee are known for many years. These processes generate significant amounts of by-products since coffee bean stands for around 50% of the coffee cherry. Therefore, considering the current pro-ecological...
-
The Effect of AgInS2, SnS, CuS2, Bi2S3 Quantum Dots on the Surface Properties and Photocatalytic Activity of QDs-Sensitized TiO2 Composite
PublicationThe eect of type (AgInS2, SnS, CuS2, Bi2S3) and amount (5, 10, 15 wt%) of quantum dots (QDs) on the surface properties and photocatalytic activity of QDs-sensitized TiO2 composite, was investigated. AgInS2, SnS, CuS2, Bi2S3 QDs were obtained by hot-injection, sonochemical, microwave, and hot-injection method, respectively. To characterize of as-prepared samples high-resolution transmission electron microscopy (HRTEM), scanning...
-
Polyolefins, commercial and alternative routes toward the world’s most important polymer
e-Learning CoursesThe course will consist of lectures followed by discussions. Based on the gained knowledge the Students will be asked to prepare in teams a short essay how to economically produce a selected polyolefin and how to introduce the new product into the market.
-
Experimental and numerical study on polymer element used for reduction of temporary steel grandstand vibrations
PublicationThe purpose of the paper is to analyse the effectiveness of a polymer damper in reduction of a temporary steel grandstand vibrations through the experimental and numerical study. The damper considered in the investigation is constructed out of two L-shape steel members bonded with polymer mass of high damping properties. The element has been installed as a diagonal one at the back part of the structure. The method has been compared...
-
Imprinted polymer particles for iron uptake: Synthesis, characterization and analytical applications
Publication -
Electrochemical behavior of a composite material containing 3D-structured diatom biosilica
Publication3D-structured diatom biosilica mixed with conducting carbon black was investigated as an active electrode material for lithium-ion batteries. Diatom biosilica was obtained by cultivation of the selected diatom species under laboratory conditions. Several instrumental techniques (XRD, FTIR, Raman, SEM-EDX, TGA) were used to characterize the physicochemical properties of applied biosilica. It was evidenced that the prepared new composite...
-
Experimental and numerical evaluation of mechanical behaviour of composite structural insulated panels
PublicationComposite structural insulated panels (CSIPs) are novel prefabricated elements for structural applications. Panels under consideration are made from glass-fibre reinforced magnesia cement boards as facesheets and expanded polystyrene foam (EPS) as a core. Quasi-static full-scale and model bending tests under monotonic loading were performed to recognize mechanical properties of CSIPs in flexure. In addition, tensile, compressive,...
-
Application of lightweight cement composite with foamed glass aggregate in shell structures
PublicationThe purpose of the paper is to investigate the abilities of applying Granulated Expanded Glass Aggregate (GEGA) as a natural volume substitute of aggregate as a component of lightweight concrete. The GEGA aggregates used in the experiments were made of confused glass waste. In order to achieve satisfactory strength of concrete Granulated Ash Aggregate (GAA) was added as well. To produce specimens three grain sizes of aggregates...
-
Bulk-Surface Modification of Nanoparticles for Developing Highly-Crosslinked Polymer Nanocomposites
PublicationSurface modification of nanoparticles with functional molecules has become a routine method to compensate for diffusion-controlled crosslinking of thermoset polymer composites at late stages of crosslinking, while bulk modification has not carefully been discussed. In this work, a highly-crosslinked model polymer nanocomposite based on epoxy and surface-bulk functionalized magnetic nanoparticles (MNPs) was developed. MNPs were...