Search
Search results for: porous materials
-
Effect of Some Sulphur Additives on The Degradation of 9Cr-1Mo Steel After Its 10 Years Service in The CCR Platforming Unit
PublicationThe work shows the results of the tests of 9Cr-1Mo steel, which was for 10 years operated in the CCR platforming unit in Group Lotos SA in Gdańsk, and then in the laboratory was sulphidised during 166 h at a temperature of 600 °C. Sulphidation was performed in a mixture of H2-H2S gases at the vapour pressure of sulphur 4.1·10-14 atm, so the order of magnitude of vapour pressure was less than that of the dissociation pressure of...
-
Poroelastic Low Noise Road Surfaces
PublicationNoise is one of the most important problems related to road traffic. During the last decades, noise emitted by engine and powertrain of vehicles was greatly reduced and tyres became a clearly dominant noise source. The paper describes the concept of low noise poroelastic road surfaces that are composed with mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and are much more flexible...
-
Femtosecond laser ablated trench array for improving performance of commercial solid oxide cell
PublicationThe performance of electrode-supported solid oxide cells (SOCs) is limited adversely by gas diffusion impedance in thick and porous support. This work focuses on the improvement of gas transport properties of commercial Ni-YSZ anode-supported SOFC by femtosecond laser-based micromachining where micro-holes of identical depth but different hole separations pitches with minimal heated affected zones were imposed. The polarization...
-
Monolithic capsule phase microextraction prior to gas chromatography-mass spectrometry for the determination of organochlorine pesticides in environmental water samples
PublicationIn this study, a capsule phase microextraction (CPME) protocol followed by gas chromatography-mass spectrometry is proposed for the accurate and sensitive monitoring of organochlorine pesticides (OCPs) in environmental water samples. Different monolithic sol–gel encapsulated sorbents were compared and monolithic sol–gel poly(ethylene glycol)-based sorbent incorporated into porous microextraction capsules resulted in the highest...
-
Exposure scenario and risk assessment of infants and newborns to bisphenols and their derivatives from diapers
PublicationNewborns and infants are more sensitive to harmful compounds such as bisphenols and their derivatives because of their not fully developed detoxification mechanism. Exposure to these substances can lead to developmental problems and health consequences in adulthood. Since disposable baby diapers are used from the first days of life and remain in contact with the baby skin, it seems important to monitor the levels of endocrine disrupting chemicals...
-
Poroelastic Road Surface – a Promising Road Traffic Noise Abatement Solution
PublicationRoad surfaces have a direct impact on the generation of noise by rolling tyres, the main and dominant source of noise of moving vehicles, as well as may affect propagation of noise emitted by all noise sources of a vehicle. Thus there is no doubt that pavement should be considered as one of the major potential road traffic noise abatement measure. Low noise pavements of existing types may in new conditions provide up to 8 dB of...
-
Methods of trend removal in electrochemical noise data – overview
PublicationIn this paper we shall review popular methods of trend removal from electrochemical noise time records. The basic principles of operation of the six most popular methods are explained. The proposed methods are: high - pass filtering, Moving Average Removal, polynomial detrending, wavelet detrending, Empirical Mode Decomposition and Variational Mode Decomposition. Estimation of trend removal quality...
-
Ultra Low Noise Poroelastic Road Surfaces
PublicationNoise is one of the most important environmental problems related to road traffic. During the last decades, the noise emitted by the engines and powertrains of vehicles was greatly reduced and tires became a clearly dominant noise source. The article describes the concept of low noise poroelastic road surfaces that are composed of mineral and rubber aggregate bound by polyurethane resin. Those surfaces have a porous structure and...
-
Application of Artificial Neural Networks to Predict Insulation Properties of Lightweight Concrete
PublicationPredicting the properties of concrete before its design and application process allows for refining and optimizing its composition. However, the properties of lightweight concrete are much harder to predict than those of normal weight concrete, especially if the forecast concerns the insulating properties of concrete with artificial lightweight aggregate (LWA). It is possible to use porous aggregates and precisely modify the composition...
-
Temperature influence on tyre/road noise of selected tyres
PublicationAir and road temperatures substantially affect road vehicle noise emission. The temperature influence on tyre/road noise depends mainly on tyre-road combination. It is different for dense and porous pavements, for bituminous and cement ones. It differs also depending on tyres. The correction procedures for temperature effect are still under consideration and preparation. Tyre/road noise measurements using CPX method were performed...
-
The Use of Direct Shear Test for Optimization of Interlayer Bonding Under a Poroelastic Layer
PublicationPoroelastic Road Surfaces (PERS) are characterised by porous structure with air void content of 20% or higher and stiffness almost 10 times lower than that of a standard asphalt course. Such properties enable noise reduction by up to 12 dB in comparison to SMA 11 mixture. However, the disadvantage of a poroelastic pavement is its low durability, which partially results from delamination from the lower layer. The paper aims to investigate...
-
Acoustic lifecycle study of the double-layer porous asphalt on E4 in Huskvarna, Sweden
PublicationIn 2010 a double-layer porous asphalt concrete (DPAC) pavement was constructed on the E4 motorway through the Swedish city Huskvarna. Earlier experience in Sweden indicated that it was feasible to obtain a high initial noise reduction but due to the widespread use of studded tires in winter, clogging and ravelling created losses of around 2 dB per year, with an expected acoustical lifetime of only 3 years. However, the improved...
-
Raman investigation of the patina layers on Hungarian copper ingots from a fifteenth century shipwreck
PublicationWe report results of the patina study of underwater archeological finding ofmedieval copper objects performed by means of the Raman and complementary spectroscopic techniques. The objects were found submerged in the sea as cargo part of the ship which sunk in the Gulf of Gdańsk in 1408. The excavated collection consists of 230 oval ingots of the size and mass up to about 60 cm and 18 kg (total of 2 tons), respectively. In the Raman...
-
Polychlorinated biphenyls (PCBs) and polychlorodibenzo-p-dioxins (PCDDs) determination in disposable baby diapers with the application of natural deep eutectic solvent
PublicationIn this work a new method involving solvent extraction of porous membrane-packed solid samples (SE-PMSS) coupled to gas chromatography-mass spectrometry (GC–MS) has been developed for the determination of six polychlorinated biphenyls (PCBs) and five polychlorodibenzo-p-dioxines (PCDDs) in disposable baby diapers. In that aim, a terpenoid-based natural deep eutectic solvent (NADES) composed of carvone and camphor in a 1:1 M ratio...
-
Comparison of Properties of the Hybrid and Bilayer MWCNTs—Hydroxyapatite Coatings on Ti Alloy
PublicationCarbon nanotubes are proposed for reinforcement of the hydroxyapatite coatings to improve their adhesion, resistance to mechanical loads, biocompatibility, bioactivity, corrosion resistance, and antibacterial protection. So far, research has shown that all these properties are highly susceptible to the composition and microstructure of coatings. The present research is aimed at studies of multi-wall carbon nanotubes in three different...
-
Effect of free water on the quasi‑static compression behavior of partially‑saturated concrete with a fully coupled DEM/CFD approach.
PublicationThe work aims to numerically investigate the quasi-static response of partially fluid-saturated concrete under two-dimensional uniaxial compression at the mesoscale. We investigated how the impact of free pore fluid content (water and gas) affected the quasi-static strength of concrete. The totally and partially fluid-saturated concrete behavior was simulated using an improved pore-scale hydro-mechanical model based on DEM/CFD....
-
Port Cities within Port Regions: Shaping Complex Urban Environments in Gdańsk Bay, Poland
PublicationPort cities located within various metropolitan or functional regions face very different development scenarios. This applies not only to entire municipalities but also to particular areas that play important roles in urban development—including ports as well as their specialized parts. This refers also to the various types of maritime industries, including the processing of goods, logistics operations, shipbuilding, or ship repairing,...
-
A hierarchical porous composite magnetic sorbent of reduced graphene oxide embedded in polyvinyl alcohol cryogel for solvent‐assisted‐solid phase extraction of polycyclic aromatic hydrocarbons
PublicationA hierarchical porouscomposite magnetic sorbent was fabricated and applied tothe dispersive solvent-assisted solid-phase extraction of five polycyclic aromatichydrocarbons. A sorbent was first prepared by incorporating graphene oxide,calcium carbonate, and magnetite nanoparticles into a polyvinyl alcohol cryo-gel. The graphene oxide was converted to reduced graphene oxide using ascorbicacid and a hierarchical porous structure was...
-
Ultrasound assisted solvent extraction of porous membrane-packed samples followed by liquid chromatography-tandem mass spectrometry for determination of BADGE, BFDGE and their derivatives in packed vegetables
PublicationThe problem of the presence of trace organic pollutants in food is of growing importance due to increasing awareness about their impact on newborns, infants and adults of reproductive age. Despite the fact that packaged food products offer many advantages, packaging can be a source of contamination for stored food. Thus, monitoring such pollution in food is of high importance. In this work, a novel methodology based on the solvent...
-
Ultrasound-Assisted Solvent Extraction of a Porous Membrane Packed Sample for the Determination of Tobacco-Specific Nitrosamines in the Replacement Liquids for E-Cigarettes
PublicationThe content of tobacco-specific nitrosamines (TSNAs) possessing carcinogenic properties has been an important area of research since replacement liquids were introduced for e-cigarettes. A method for determining N′-nitrosonornicotine (NNN), 4-(methylnitrosamino)-1-(3-pyridyl)-1-butanone (NNK), N′-nitrosoanatabine (NAT), and N′-nitrosoanabasine (NAB) in replacement liquids for electronic cigarettes was developed using liquid chromatography–tandem...
-
Organic Acids and Polyphenols Determination in Polish Wines by Ultrasound-Assisted Solvent Extraction of Porous Membrane-Packed Liquid Samples
PublicationIn the near future, Poland is going to have more and more favorable conditions for viticulture. Organic acids and polyphenols are among the most commonly analyzed compounds due to their beneficial properties for human health and their importance in the winemaking process. In this work, a new technique involving ultrasound-assisted solvent extraction of porous membrane-packed liquid samples (UASE-PMLS) was for the first time described...
-
Application of shifted Chebyshev polynomial-based Rayleigh–Ritz method and Navier’s technique for vibration analysis of a functionally graded porous beam embedded in Kerr foundation
PublicationPresent study is dealt with the applicability of shifted Chebyshev polynomial based Rayleigh-Ritz method and Navier’s technique on free vibration of Functionally Graded (FG) beam with uniformly distributed porosity along the thickness of the beam. The material properties such as Young’s modulus, mass density, and Poisson’s ratio are also considered to vary along the thickness of the FG beam as per the power-law exponent model....
-
Influence of Ultrasound on the Characteristics of CaP Coatings Generated Via the Micro-arc Oxidation Process in Relation to Biomedical Engineering
PublicationOver the past decade, bone tissue engineering has been at the core of attention because of an increasing number of implant surgeries. The purpose of this study was to obtain coatings on titanium (Ti) implants with improved properties in terms of biomedical applications and to investigate the effect of ultrasound (US) on these properties during the micro-arc oxidation (MAO) process. The influence of various process parameters, such...
-
Properties of an innovative multi-functional finish for the improvement of indoor air quality
PublicationDue to lifestyle changes, people spend most of their time indoors at present; thus, Indoor Air Quality (IAQ) is a matter of utmost importance. Multi-functional and innovative finishes can help to passively improve the IAQ, benefitting the health and comfort of occupants. For this study, reference and pre-mixed commercial mortars are compared to a new multi-functional hydraulic lime mortar for indoor finishes, in which conventional...
-
Exploring synergistic effects in physical-chemical activation of Acorus calamus for water treatment solutions
PublicationThe research proposed a novel method of obtaining sorption material from readily available Acorus calamus bio- mass through a combination of physical and chemical activation processes. The material with the highest specific surface area (1652 m2 g−1) was obtained by physical activation with CO2, followed by chemical activation with KOH. Reversing the order of activation methods resulted in a lower specific surface area (1014 m2...
-
Development of a new green analytical methodology for the determination of phthalates in single-use babies diapers using ultrasound-assisted extraction and polypropylene porous membrane
PublicationA green extraction strategy was developed and utilized for the extraction and determination of phthalates. The extraction is based on ultrasound-assisted extraction and a polypropylene porous membrane. The Box-Behnken model was performed to optimize the extraction condition. The optimal extraction conditions are 5.5 mL of ethyl acetate, 10 min of extraction time and 55 C for extraction temperature. The developed green extraction...
-
Air trapping problem during infiltration on the large areas
PublicationThe process of flow modeling in unsaturated porous medium is often found in many fields of sciences: geology, fluid mechanics, thermodynamics, microbiology or chemistry. Problem is relatively complicated due to complexity of the system which contains three phases: water, air and soil skeleton. The flow of water in such a medium can be described using two-phase (2PH) flow formulation, which accounts the inflow of air and water phases,...
-
Porous structures in aspects of transpirating cooling of oxycombustion chamber walls
PublicationA wet oxycombustion chamber, which must be effectively cooled due to high temperature evolved during the oxy-combustion process, by using the phenomena of Reynolds thermal transpiration and Navier slip velocity. Closures needed to execute mass flow rate in a microchannel, which should be treated as a single porous structure in the walls of the combustion chamber, have been obtained by applying a local 3D approach. The Navier-Stokes...
-
Temperature influence on tyre/road noise on poroelastic road surface based on laboratory measurements
PublicationThe temperature effect on measured tyre/road noise is very important phenomena as it may lead to significant errors in measurement results due to substantial influence of this parameter on the obtained values. It depends mainly on the particular tyre-road combination. It is different for dense and porous as well as for bituminous and cement concrete pavements. It differs also depending on tested tyre. The correction procedure for...
-
Protective properties of Al2O3 + TiO2 coating produced by the electrostatic spray deposition method
PublicationMechanical resistance of Al2O3 + TiO2 nanocomposite ceramic coating deposited by electrostatic spray deposition method onto X10CrAlSi18 steel to thermal and slurry tests was investigated. The coating was produced from colloidal suspension of TiO2 nanoparticles dispersed in 3 wt% solution of Al2(NO3)3, as Al2O3 precursor, in ethanol. TiO2 nanoparticles of two sizes, 15 nm and 32 nm, were used in the experiments. After deposition,...
-
PLA–Potato Thermoplastic Starch Filament as a Sustainable Alternative to the Conventional PLA Filament: Processing, Characterization, and FFF 3D Printing
PublicationThe growing popularity of the fused filament fabrication (FFF) 3D printing technology in science, industry, and in-home use is associated with an increased demand for high-quality polymer filaments. This study presents an in-depth characterization and analysis of a self-made bio-based polylactide (PLA)/thermoplastic potato starch (TPS) filament dedicated for the FFF 3D printing technology. The obtained results were compared with...
-
Numerical modeling of wave-seabed-structure interaction.
PublicationPraca doktorska przedstawia propozycję nowoczesnego rozwiązania obciążeń hydraulicznych przy uwzględnieniu nieliniowych oddziaływań pomiędzy falą wodną, przepuszczalnym dnem i porowatą konstrukcją morską. Nabrzeże pionowe, falochron podwodny i falochron kompozytowy były obiektem eksperymentów numerycznych, których wyniki były weryfikowane przy użyciu wyników laboratoryjnych (niszczących i nieniszczących). Krótki przegląd bieżącej...
-
A pore-scale thermo–hydro-mechanical model for particulate systems
PublicationA pore scale numerical method dedicated to the simulation of heat transfer and associated thermo–hydro-mechanical couplings in granular media is described. The proposed thermo–hydro-mechanical approach builds on an existing hydromechanical model that employs the discrete element method for simulating the mechanical behavior of dense sphere packings and combines it with the finite volume method for simulating pore space fluid flow...
-
Green capsule phase microextraction employing hydrophobic monolithic sol-gel octadecyl siloxane platforms for the monitoring of organophosphorus pesticides in environmental water samples
PublicationIn this study, a novel, facile and green capsule phase microextraction (CPME) method is presented for the extraction and preconcentration of organophosphorus pesticides (i.e., chlorpyrifos, disulfoton, ethoprophos, fenchlorphos, prothiofos, and parathion-methyl) from environmental water samples. Monolithic sol-gel octadecyl siloxane (sol-gel C18) sorbent encapsulated within porous polypropylene capsules was synthesized, characterized,...
-
Removal of diphenols using pine biochar. Kinetics, equilibrium, thermodynamics, and mechanism of uptake
PublicationThermal pyrolysis synthesized activated biochar from the Pinus elliottii sawdust (PS) at 600° C. The obtained activated biochar (PB600) was used for the removal of three diphenols, catechol (CAT), resorcinol (RES), and hydroquinone (HYD), which are utilized mainly in different industries. The PB600 was characterized by several analytical techniques. The BET surface area of 1473 m2.g−1 and a total pore volume of 0.707 cm3 g−1 was...
-
Steady magnetohydrodynamic flow in a diverging channel with suction or blowing
PublicationAn analysis is made of steady two-dimensional divergent flow of an electrically conducting incompressible viscous fluid in a channel formed by two non-parallel walls, the flow being caused by a source of fluid volume at the intersection of the walls. The fluid is permeated by a magnetic field produced by an electric current along the line of intersection of the channel walls. The walls are porous and subjected to either suction...
-
Utilization of shale cuttings in production of lightweight aggregates
PublicationThe development of technologies for unconventional hydrocarbon exploration requires designing procedures to manage drilling waste that are consistent with the waste management hierarchy. In view of this, the possibility to apply shale drill cuttings as a prospective additive (replacing bentonite) to fly ash used for the production of lightweight aggregates (LWAs) was investigated. Moreover, a facile, waste-free method of LWAs production...
-
Inhomogeneity of low-noise wearing courses evaluated by tire/road noise measurements using the close-proximity method
PublicationPerforming numerous analyses of tire/road noise measurements on low-noise pavements during the last several years, the authors observed significant inhomogeneity of the wearing course in numerous cases, while similar problems were almost non-existent when dense pavements were measured. Three main causes of low-noise pavement inhomogeneity can be defined. The first one is imperfections in the technology used for asphalt mix production...
-
Microporous Polyurethane Thin Layer as a Promising Scaffold for Tissue Engineering
PublicationThe literature describes that the most efficient cell penetration takes place at 200–500 µm depth of the scaffold. Many different scaffold fabrication techniques were described to reach these guidelines. One such technique is solvent casting particulate leaching (SC/PL). The main advantage of this technique is its simplicity and cost efficiency, while its main disadvantage is the scaffold thickness, which is usually not less than...
-
Conversion of waste biomass into activated carbon and evaluation of environmental consequences using life cycle assessment
PublicationIn this article, activated carbon was produced from Lantana camara and olive trees by H3PO4 chemical activation. The prepared activated carbons were analyzed by characterizations such as scanning electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer–Emmett–Teller, X-ray diffraction, thermogravimetric analysis, and Fourier transform infrared spectroscopy. H3PO4 is used as an activator agent to create an abundant pore...
-
Comparative study of bisphenols in e-cigarette liquids: evaluating fabric phase sorptive extraction, ultrasound-assisted membrane extraction, and solid phase extraction techniques
PublicationTo address the under-researched risk of bisphenols (BPs) in e-cigarette liquids, comprehensive studies have been conducted to propose optimum sample preparation and analysis methods. To determine twelve BPs in refill liquids for e-cigarettes, three sample preparation methods based on distinct operational and working principles were employed. These included fabric phase sorptive extraction (FPSE), ultrasound-assisted solvent extraction...
-
Study of the Resistance to Influence of Aggressive Liquids on Concrete with Lightweight Aggregate
PublicationThe corrosion of the structure of concrete caused by the aggressive external environment is one of the main problems that can reduce the durability of buildings. The paper analyzes the influence of the type of component on selected properties of lightweight concrete (LWC) exposed to aggressive liquids. When lightweight concrete containing porous aggregates is used, the influence of an aggressive environment may be of particular...
-
Electrochemical Production of Sodium Hypochlorite from Salty Wastewater Using a Flow-by Porous Graphite Electrode
PublicationThe production of sodium hypochlorite (NaOCl) from salty wastewater using an electrochemical cell has several advantages over other methods that often require hazardous chemicals and generate toxic waste, being more sustainable and environmentally friendly. However, the process of producing sodium hypochlorite using an electrochemical cell requires careful control of the operating conditions, such as the current density, flow rate,...
-
Solar light driven degradation of norfloxacin using as-synthesized Bi 3+ and Fe 2+ co-doped ZnO with the addition of HSO 5 – : Toxicities and degradation pathways investigation
PublicationIn this study, solar light responsive Bi3+ and Fe2+ doped ZnO were synthesized and used for photocatalytic degradation of norfloxacin (NOR), an emerging water pollutant. Analysis with Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), high-resolution transmission electron microscopy (HRTEM), selected area electron...
-
Decreasing CO2 Emissions By Reducing Tire Rolling Resistance
PublicationThe first motor vehicle was built by Nicolas Cugnot almost 250 years ago and since then there has been a continuous process of motor vehicles’ improvements, as well as development of new road pavements. The fuel crisis of the 70s of the 20th century made it clear to vehicle builders that measures should be taken to reduce vehicle fuel consumption and it contributed to an increased interest in electric vehicles. Although significant...
-
Evolution of Edges and Porosity of Urban Blue Spaces: A Case Study of Gdańsk
PublicationCurrent waterfront studies focus mainly on a land-based perspective, failing to include the water side. Water is, however, not just a resource for port and industrial purposes and an edge to the waterfront; it is also a feature of the waterfront and the complex relation between water and city. Thus, the article suggests that water-land edges need to be re-contextualised, taking into consideration also their shape, functionality,...
-
Noble metal modified TiO2 microspheres: Surface properties and photocatalytic activity under UV-vis and visible light
PublicationComposite photocatalysts that consist of TiO2and noble metal nanostructures have been considered tobe the promising and pivotal material for accessible enhancement of the efficiency in the photocatalyticprocess carried out in the aqueous and gas phases. In this work we fabricated porous TiO2microspheresthrough a hydrothermal process followed by photochemical reduction of noble metal nanoparticles atthe TiO2surface. The morphology...
-
Preparation, characterization and photocatalytic activity of TiO2 microspheres decorated by bimetallic nanoparticles
PublicationComposite photocatalysts that consist of TiO2and noble metal nanostructures have been considered tobe the promising and pivotal material for accessible enhancement of the efficiency in the photocatalyticprocess carried out in the aqueous and gas phases. In this work we fabricated porous TiO2microspheresthrough a hydrothermal process followed by photochemical reduction of noble metal nanoparticles atthe TiO2surface. The morphology...
-
Modelling of Asphalt Mixes under Long Time Creep at Low Temperatures
PublicationProper description of asphalt mixtures behavior under long time load is one of the most important factors in analyses of strain and stress relations at low temperatures both from traffic and environmental loads. For example different models of thermal stress accumulation require different approaches of description of asphalt concrete. But in all cases it is required to describe its behavior under long time loading, which in some...
-
Degradation of cefadroxil drug by newly designed solar light responsive alcoholic template-based lanthanum ferrite nanoparticles
PublicationIn this work, lanthanum ferrite nanoparticles were synthesized via a simple co-precipitation method. Two different templates, namely sorbitol and mannitol, were used in this synthesis to tune the optical, structural, morphological, and photocatalytic properties of lanthanum ferrite. The synthesized lanthanum ferrite-sorbitol (LFOCo-So) and lanthanum ferrite-mannitol (LFOCo-Mo) were investigated through Ultraviolet–Visible (UV–Vis),...