displaying 1000 best results Help
Search results for: COMPOSITE ANODE MATERIALS
-
COMPUTATIONAL MATERIALS SCIENCE
Journals -
Structural, thermal and physico-mechanical properties of polyurethane/brewers’ spent grain composite foams modified with ground tire rubber
PublicationIn this work, brewers’ spent grain (BSG) and ground tire rubber (GTR) waste fillers were applied as low-cost reinforcement phase in rigid polyurethane foam (PUR). PUR/BSG/GTR composites were prepared by a single step method, using polyglycerol as partial substitute of commercially available petrochemical polyols. Foaming parameters, chemical structure, dynamic mechanical properties, thermal stability, physico-mechanical properties...
-
Fabrication, structural and electrical properties of Sr(V,Nb)O 3-δ perovskite materials
PublicationThe SrV1-xNbxO3-δ materials with different niobium content in perovskite B-sublattice were prepared by a solid-state reaction process. The microstructure and phase compositions of obtained samples were analyzed by the X-ray diffraction technique (XRD) and scanning electron microscopy (SEM). The electrical conductivity of samples was measured by a DC 4-wire method in range of 100–600 °C in different gas conditions. The oxidation...
-
Changes on the Surface of the SiO2/C Composite, Leading to the Formation of Conductive Carbon Structures with Complex Nature of DC Conductivity
Open Research DataChanges on the Surface of the SiO2/C Composite, Leading to the Formation of Conductive Carbon Structures with Complex Nature of DC Conductivity
-
Exploration of optical fibres as a carrier for new benzene and toluene matrix-free reference materials
PublicationTo meet high expectations concerning precision and accuracy of reference materials, preparation of matrixfree reference materials using thermal decomposition-gas chromatography-mass spectrometry (TD-GC-MS) was proposed in this study. In the paper, the results obtained in preparation of the new reference materials for benzene and toluene are presented, based on the thermal decomposition technique of compounds chemically bound to...
-
Novel MNZ-type microwave sensor for testing magnetodielectric materials
PublicationA novel microwave sensor with the mu-near-zero (MNZ) property is proposed for testing magnetodielectric material at 4.5 GHz. The sensor has a double-layer design consisting of a microstrip line and a metal strip with vias on layers 1 and 2, respectively. The proposed sensor can detect a unit change in relative permittivity and relative permeability with a difference in the operating frequency of 45 MHz and 78 MHz, respectively....
-
Anna Zielińska-Jurek prof. dr hab. inż.
People2018 DSc in technical sciences in the field of chemical technology Chemical Faculty, Gdansk University of Technology, Title: “Functionalized titanium(IV) oxide as a photocatalyst for environmental purification” 2011 Ph. D. in technical sciences in the field of chemical technology Chemical Faculty, Gdansk University of Technology, Title of the dissertation:...
-
Low velocity impact damage in glass/polyester composite sandwich panels
PublicationZbadano odporność udarową konstrukcji przekładkowych z laminatu poliestrowo szklanego pod kątem adhezji z rdzeniem (pianki PVC) przy polaczeniu dwoma rodzajami kleju lub łączanymi na ''mokro'' przy pomocy żywicy w trakcie utwardzania laminatu. Do oceny obszaru zniszczeń udarowych zastosowano metodę ultradźwiękową, która umożliwia wykrycie pola delaminacji nakładających się na siebie w poszczególnych warstwach .Obszary zniszczeń...
-
Strength of Materials II,Lectures,DAPE,spring 21-22 (PG_00050281)
e-Learning CoursesThe aim of the subject is to acquire knowledge related to the strength of materials II (mechanics of material, part 2)
-
From flow to jamming: Lattice Gas Automaton simulations in granular materials
PublicationWe introduce the first extension of a Lattice Gas Automaton (LGA) model to accurately replicate observed emergent phenomena in granular materials with a special focus on previously unexplored jamming transitions by incorporating gravitational effects, energy dissipation in particle collisions, and wall friction. We successfully reproduce flow rate evolution, density wave formation, and jamming transition observed in experiments....
-
Scanning Electron Microscopy (SEM ) images of PC-X (porous carbon materials obtained at various temperatures)
Open Research DataThese data contain SEM (scanning electron microscopy) images of PC-700 (porous carbon materials obtained at 700°C), PC-800 (porous carbon materials obtained at 800°C) and PC-900 (porous carbon materials obtained at 900°C).
-
X-ray Diffraction (XRD) patterns of PC-X (porous carbon materials obtained at various temperatures)
Open Research DataThese data contain X-ray diffraction patterns (XRD) of PC-700 (porous carbon materials obtained at 700°C), PC-800 (porous carbon materials obtained at 800°C) and PC-900 (porous carbon materials obtained at 900°C).
-
[IMa] Materials technologies - 2023/24
e-Learning Courses{mlang pl} Dyscyplina: inżynieria materiałowa Zajęcia obowiązkowe dla doktorantów I roku Prowadzący: prof. dr hab. inż. Maria Gazda, prof. dr hab. inż. Józef Haponiuk, dr hab. inż. Sebastian Molin, dr hab. inż. Jacek Ryl, dr hab. inż. Robert Bogdanowicz Liczba godzin: 15 Forma zajęć: wykład/seminarium {mlang} {mlang en} Discipline: materials engineering Obligatory course for 1st year PhD students Academic teachers: prof....
-
Partial PLA composite surface activation by femtosecond laser ablation
Open Research DataThe dataset contains the studies on electrochemical activity of PLA composite (commercially available CB-PLA Protopasta), which was 3D printed in a form of 1x1cm electrodes. The electrodes were submitted to femtosecond laser ablation operating with different parameters. These were: gas atmosphere (He or air, data in different subfolders), the percentage...
-
Electrochemistry for materials science
e-Learning Courses -
Superconductivity and Superconducting Materials
e-Learning Courses -
Experimental and analytical thermal study of PTFE composite sliding against high carbon steel as a function of the surface roughness, sliding velocity and applied load
PublicationThis study investigates the contact temperatures caused by frictional heating of sliding parallel pairs. In this case the materials studied are a PTFE composite in contact with a high carbon steel plate. These materials are commonly used for industrial applications, in particular as the main contacting components within a scroll expander system. The expected contact temperature values are important to be quantified in order to...
-
Structural and electrical properties of Cr-doped SrTiO 3 porous materials
PublicationSeries of single-phase materials with assumed formula SrTi1−xCrxO3 (where x = 0, 1, 4, 6 mol.%) were obtained by sol-gel method. The structure and microstructure of materials were characterised by X-ray diffraction and scanning electron microscopy methods. Moreover, the study of electrical properties and evaluation of chemical stability in CO2/H2O atmosphere was performed by electrochemical impedance spectroscopy and thermogravimery...
-
Formation of Porous Structure of the Metallic Materials Used on Bone Implants
PublicationResearch on improvement of structure and fabrication methods of the bone implants are carried out for many years. Research are aimed to shape the structures, that will have a Young's modulus value similar to the value of the human bones Young's modulus. Depending on theporosity, Young's moduli can even be tailored to match the modulus of bone closer than solid metals can, thus reducing the problems associated with stress shielding...
-
TiO 2 Co x O y composite nanotube arrays via one step electrochemical anodization for visible light–induced photocatalytic reaction
PublicationTiO2CoxOy (x = 1, y = 1 or x = 3, y = 4) composite photocatalysts have been synthesized via one step anodic anodization of TiCo alloys. The effects of the cobalt content in the alloy (5, 10 and 15 wt%), water content (2, 5 and 10%) in the electrolyte solution, and applied voltage (30, 40 and 50 V) during the anodization process on the morphology and surface properties. Additionally, the dependence of cobalt content in the nanotubes...
-
Experimental investigation of Steel–Concrete–Polymer composite barrier for the ship internal tank construction
PublicationTransportation of dangerous cargo by ships demands ensuring an appropriate protection level in case of an accident. Two of the most dangerous accident types resulting in an oil spill are grounding and ship to ship collision. The article presents results of research on a new composite construction for a ship hull that increases structural safety during collision. The concept of semi-elastic Steel–Concrete–Polymer structure is presented....
-
Formation of Highly Conductive Boron-Doped Diamond on TiO2 Nanotubes Composite for Supercapacitor or Energy Storage Devices
PublicationIn the present paper, we report the phenomena of the formation of the novel composite nanostructures based on TiO2 nanotubes (NTs) over-grown by thin boron-doped diamond (BDD) film produced in Microwave Plasma Enhanced Chemical Vapor Deposition (PE MWCVD). The TiO2 nanotube array overgrown by boron-doped diamond immersed in 0.1 M NaNO3 can deliver high specific capacitance of 7.46 mF cm−2. The composite electrodes were characterized...
-
Towards Computer-Aided Graphene Covered TiO2-Cu/(CuxOy) Composite Design for the Purpose of Photoinduced Hydrogen Evolution
PublicationIn search a hydrogen source, we synthesized TiO2-Cu-graphene composite photocatalyst for hydrogen evolution. The catalyst is a new and unique material as it consists of copper-decorated TiO2 particles covered tightly in graphene and obtained in a fluidized bed reactor. Both, reduction of copper from Cu(CH3COO) at the surface of TiO2 particles and covering of TiO2-Cu in graphene thin layer by Chemical Vapour Deposition (CVD) were...
-
[NCh, IMa] Properties of novel materials
e-Learning Courses{mlang pl} Dyscyplina: nauki chemiczne, inżynieria materiałowa Zajęcia fakultatywne Prowadzący: prof. dr hab. inż. T. Klimczuk, WFTiMS Liczba godzin: 15 Forma zajęć: wykład {mlang} {mlang en} Discipline: chemical sciences, materials engineering facultative course Academic teacher: prof. dr hab. inż. T. Klimczuk, WFTiMS Total hours of training:15 teaching hours Course type: lecture {mlang}
-
Investigating BiMeVOx compounds as potential photoelectrochemical and electrochemical materials for renewable hydrogen production
PublicationIn this study, BiMeVOx compounds (where Me: Co, Mo, Ce, Zr) were synthesized and characterized as potential photoelectrochemical materials for solar water splitting, the hydrogen evolution reaction (HER), and oxygen evolution reaction (OER). The analysis confirmed the successful formation of phase BiMeVOx compounds with the desired crystal structure. Among the tested materials, BiCoVOx(800) showed the highest photocurrent density...
-
Impact response of novel layered two stage fibrous composite slabs with different support type
PublicationThe performance of novel Layered Two Stage Fibrous Composite slabs (LTSFC) was pioneered under falling mass collisions using a combined experimental and numerical study. Such LTSFC slabs consist of three layers with and without the insertion of glass fibre mesh between the layers. LTSFC techniques were used to fabricate the composite slabs with three layers including 3%, 1.5%, and 3% of fibre content for the top, middle, and...
-
A Monte Carlo Strategy to simulate Positrons and Positronium in biological Materials
PublicationWe present an algorithm for Monte Carlo simulations of positron tracks in biological materials. The algorithm takes into account the cross-section data for elastic and inelastic collisions between positrons and molecules and processes like direct annihilation, ionization and positronium formation. In the case of positronium formation, the algorithm considers the interactions of positronium with molecules. The algorithm can be used...
-
Reviewing the recent developments of using graphene-based nanosized materials in membrane separations
PublicationAccording to the potentialities of graphene-based materials and their unique physicochemical properties. Such 2D nanomaterials are likely to be the most implemented within the improvement of the selective separations of polymer membranes, together with enhanced physicochemical properties (such as hydrophilicity/hydrophobicity, transport of molecules, mechanical and thermal features, among others). Hence, this review compiles and...
-
MXene-based materials for removal of antibiotics and heavy metals from wastewater– a review
PublicationAs a novel family of 2D materials, MXenes provide an extensive variety of applications in water and effluent treatment due to their distinctive properties and attractive applicability, including superior electrical conductivity, higher thermal stability, hydrophilicity, and high sorption-reduction capacity. Their excellent sorption selectivity makes them perfect for removing hazardous contaminants. Currently, MXene-based materials...
-
Application of the X-ray micro computed tomography to the analysis of the structure of polymeric materials
PublicationIn this paper the application of X-ray micro-computed tomography (micro-CT) as a non-destructive testing method of polymeric materials is presented. Increasing applicability of polymers in variedend-use industries such as automotive, building and construction, consumer goods, and packaging is propelling the growth of the global polymer processing market. However, controlling of the polymer structure is one of the most important...
-
A Quantitative Investigation of Dislocation Density in an Al Matrix Composite Produced by a Combination of Micro-/Macro-Rolling
PublicationAn aluminum matrix composite with dispersed carbon nanotubes (CNTs) was produced via flake powder metallurgy using a micro-rolling process and vacuum hot pressing (VHP), followed by conventional rolling using a macro-rolling process. The microstructure and mechanical properties of the produced composites were studied. In addition, a new quantitative model was introduced to study the dislocation density based on the microstructural...
-
Waste materials assessment for phosphorus adsorption toward sustainable application in circular economy
PublicationPhosphorus is the main determinant of nutrient enrichment in the water bodies. Many resources including nutrients may be shortly exhausted, assuming current consumption. This scenario leads to growing interest in resources recovery and/or reuse, which together with sustainable energy consumption and waste reduction are the main courses of the circular economy. Usage of coagulants in wastewater treatment plants (WWTP) does not allow...
-
Closing the loop: Upcycling secondary waste materials into nanoarchitectured carbon composites for the electrochemical degradation of pharmaceuticals
PublicationIn this study, we demonstrated the application of electrochemical oxidation as a safer and cleaner technology for minimizing the impact of pharmaceuticals in wastewaters, simultaneously mediated by upcycled secondary waste materials (SWMs)-derived electrodes, to further reduce their environmental impact. The modularity, scalability, ease of operation and reliability make electrochemical oxidation an ideal process for the destruction...
-
Experimental and numerical investigation of mercury removal from flue gas by sorbent polymer composite
PublicationThis paper presents an experimental and numerical investigation of the performance of a sorbent polymer composite (SPC) material used for removing mercury from the flue gases in a full-scale industrial installation. The investigated material is an attractive alternative to activated carbon, which is commonly used for this purpose. While the application of the SPC is characterized by high capital expenditures, this technology offers...
-
Stefan Dzionk dr hab. inż.
People -
Effect of glycolysate obtained from polyurethane wastes on mechanical properties of rubber materials
PublicationThe paper presents the possibility of utilization of wastes from polyurethane foams. In this work the results of mechanical investigations of materials obtained from natural rubber mixtures with a mixture of glycolysate and biodiesel glycerine as a plasticizer are described. The measurements of mechanical properties showed rather good tensile strength, elongation at break and modules of extensions M100%, M200%, M300% of obtained...
-
Silicon Oxycarbide (SiOC) Ceramic Materials as Anodes for Lithium Ion Batteries
PublicationPolymer derived ceramics (PDCs) have attracted attention as alternative anode material for Li-ion batteries. It has been found that ternary SiOC and SiCN ceramics obtained through pyrolysis of various preceramic polymers display high reversible capacities of 500 – 650 mAh/g. In this work we try to correlate the electrochemical performance of polymer derived silicon oxycarbide with its chemical composition and microstructural features....
-
BUILDINGS AND CONSTRUCTIONS FROM BUILDING WASTE MATERIALS IN ACCORDANCE WITH THE NEW CIRCULAR ECONOMY TREND
PublicationMATERIALS April 18-22, 2022 / BOSTON, MA Abstract Book 3rd INTERNATIONAL CONFERENCE ON MATERIALS SCIENCE & ENGINEERING Day 5 Friday, April 22, 2022 Parallel Sessio II- (Virtual EST Zone) pp. 154 3rd INTERNATIONAL CONFERENCE ON MATERIALS SCIENCE & ENGINEERING APRIL 18-22, 2022 | BOSTON, MAAt: Boston, MAAffiliation: UNICEF at: USA BOSTONVolume: 2022
-
Flame-Retardant Polymer Materials Developed by Reactive Extrusion: Present Status and Future Perspectives
PublicationThe development of flame retardant polymer materials has two roots, one in materials design, and the other in materials processing. Over recent decades, different types and classes of flame retardant polymer materials have been commercialized to meet safety requirements in the construction, automotive, and coatings industries. In the vast majority of cases, the design and fabrication of new materials presenting low fire hazards...
-
Problems and challenges associated with estimating the emissions of organic compounds from indoor materials
PublicationFor several years intensive research has been carried out with the aim of developing a database of the types and amounts of pollutants released from indoor materials to the indoor environment. The paper discusses in detail basic problems and challenges encountered when estimating the emissions of chemical compounds released from of indoor materials. Factors affecting the validity of data obtained by using two different types of...
-
The application of TD-GC-FID technique for production of matrix-free reference materials
PublicationIn the last few years particular pressure is exerted on finding new analytical methods which would provide real possibilities of monitoring and control of the state of the environment. Intensive development of analytical techniques for measurements of gaseous media and the negative effects of BTX compounds make it necessary to produce new gaseous reference materials. To prepare the appropriate non- matrix reference material thermal...
-
Advanced Engineering Materials, W, IDE, sem.01, letni 22/23 (PG_00057376)
e-Learning CoursesLecture for Advanced Engineering Materials, for IDE course
-
Advanced Engineering Materials, L, IDE, sem.01, letni 22/23 (PG_00057376)
e-Learning CoursesLaboratory for Advanced Engineering Materials, for IDE course
-
On the material symmetry group for micromorphic media with applications to granular materials
PublicationWithin the framework of the theory of nonlinear elastic micromorphic continua we introduce the new definition of the local material symmetry group. The group consists of ordered triples of second- and third-order tensors describing such changes of a reference placement that cannot be recognized with any experiment. Using the definition we characterize the micromorphic isotropic media, micromorphic fluids, solids and special intermediate...
-
A critical review on electrospun membranes containing 2D materials for seawater desalination
PublicationElectrospun nanofibers are a cutting-edge class of membranes which have been applied in several molecular separations. These membranes can be well designed and tailored due to the versatility of the electrospinning process. Eminently, electrospun membranes, once implemented in membrane processes, are an alternative in removing salts and some other minerals from water, so-called desalination, for producing drinking water. Such membranes...
-
Damage Detection of Steel-Concrete Composite Beam
Publication -
Wavelet Analysis for Damage Identification in Composite Structures
Publication -
Wavelet analysis for damage identification in composite structures
Publicationw pracy zaproponowano metodę analizy sygnalu opartą o transformatę falkową, pozwalajacą na identyfikcaje pęknięcia zmęczeniowego w jednowymiarowych elementach konstrukcyjnych wykonanych z materialow kompozytowych
-
Role of composite cathodes in single chamber SOFC.
PublicationZbadano wpływ składu katody na napięcie oraz wydajność ogniw paliwowych pracujących w konfiguracji jednokomorowej. W związku z tym, że takie ogniwo pracuje w mieszanienie powietrza i paliwa, napięcie jest określone przez różnice aktywności katalitycznej anody i katody. Typowy cermet na bazie niklu oraz związki perovskitów pracują dobrze odpowiednio jako anoda i katoda. Jednakże perowskity mają również właściwości katalityczne,...
-
Wave Propagation Modelling in Composite Plates with Damages
PublicationW pracy przedstawiono model i wyniki analizy propagacji fali spręzystej w płycie kompozytowej z uszkodzeniami.