Search
Search results for: NAVIGATIONAL BRIDGE EQUIPMENT
-
Chemical investigation of the Al2O3 ultra-thin films
Open Research DataUltra-thin layers of oluminum oxide (Al2O3) were deposited by ALD method. Atomic layer deposition provides precise thickness control down to a single atomic layer. The precursors used were trimethylaluminum (Sigma-Aldrich) and purified water. The deposition of the atomic layer was carried out at 200 °C. Samples with a thickness of 2 and 8 nm of alumina...
-
Frequency Diagnostics of Transformer Insulating Parameters
PublicationIn the article is presented experimental analysis and diagnostics of insulating system oil-paper for power transformers, mainly by progressive frequency method – dielectric spectroscopy. In the 1-st part of the article is described base theory about measurement and diagnostics insulating part (oil and paper) of power transformers. In the 2-nd part of article is described measuring method of insulating frequency diagnostics - frequency...
-
Raman miniaturised system for field applications
PublicationRaman spectroscopy is a powerful and versatile research technique with a broad range of potential applications, which includes laboratory studies, on-line industrial process monitoring and field measurements. Scope of the field applications includes environment monitoring, detection of dangerous or prohibited materials and rapid identification of unknown samples. It stimulates development of dedicated Raman measurement equipment...
-
Thermogravimetric analysis/ pyrolysis of used tyres and waste rubber
PublicationThe process of pyrolysis is investigated in this paper. The pyrolysis results of two samples: waste tyres and rubber at different heating rates (10, 20, 50 K/min), were compared. In other experiments the degradation of two pyrolysis products, char and oil was examined. The kinetic study using the thermogravimetry equipment (TG) was done, which allowed determination of the kinetic mechanism of the process. The elemental analysis...
-
Problems of Selecting Protection for Shunt Reactors Working in Extra-High Voltage Grids
PublicationThis paper presents difficulties encountered when designing protection devices for shunt reactors connected directly to extra-high voltage grids. Using the example of the 400 kV Ełk Bis substation, it has been demonstrated that protection of a shunt reactor based on equipment using measurements of electrical signals from voltage and current transformers has its limitations and, in some cases, may be insufficient.
-
Low cost electrochemical sensor module for measurement of gas concentration
PublicationThis paper describes a low cost electrochemical sensor module for gas concentration measurement. A module is universal and can be used for many types of electrochemical gas sensors. Device is based on AVR ATmega8 microcontroller. As signal processing circuit a specialized integrated circuit LMP9l000 is used. The proposed equipment will be used as a component of electronic nose system employed for classifying and distinguishing...
-
Wpływ sposobu odwzorowania pojazdu szynowego na odpowiedź dynamiczną przęsła mostowego
PublicationW pracy przedstawiono rezultaty analiz numerycznych oraz badań eksploatacyjnych dwóch przęseł mostowych wymuszonych ruchomym pojazdem szynowym. Pojazd odwzorowano za pomocą czterech modeli uproszczonych: strumienia sił skupionych, strumienia mas skupionych oraz strumieni oscylatorów jedno- i dwumasowych. Analizy numeryczne wykonano przy wykorzystaniu MES. Potrzebne parametry dynamiczne wyznaczono na podstawie wyników identyfikacji...
-
Dynamic Tests and Technical Monitoring of a Novel Sandwich Footbridge
PublicationA novel sandwich composite footbridge is described in this paper, for the first time after it has been put into operation over the Radunia River in the Pruszcz Gdański municipality. This paper presents results of dynamic tests and describes technical monitoring of the footbridge. The dynamic tests were conducted to estimate pedestrian comfort and were compared with the ones from numerical simulations made in the environment of...
-
Informal employment in Poland: an empirical spatial analysis
PublicationThe main goal of our article is to bridge the gap in the regional analysis of informal employment in Poland and in particular to indicate the propensity for informal work in the working-age population, to test if informal activities are typical for marginalized people (less educated, unemployed, older) and to identify the regional and spatial heterogeneity in the propensity. We use data from the ‘Human Capital Balance 2010–2014’...
-
Stefan Dzionk dr hab. inż.
People -
Statistical Tuning of Walfisch-Ikegami Model for the Untypical Environment
PublicationThe Walfisch-Ikegami model has been investigated in terms of mobile radio systems designing in the untypical environment such as the maritime container terminal. The measurement equipment and procedures have been described as well as characteristics of investigated environment. Results of the statistical tuning in terms of path loss estimation in such environment have been analysed. The analysis has proved improvement of the path...
-
Statistical Tuning of Walfisch-Ikegami Model for the Untypical Environment
PublicationThe Walfisch-Ikegami model has been investigated in terms of mobile radio systems designing in the untypical environment such as the maritime container terminal. The measurement equipment and procedures have been described as well as characteristics of investigated environment. Results of the statistical tuning in terms of path loss estimation in such environment have been analysed. The analysis has proved improvement of the path...
-
Analiza techniczno-ekonomiczna rozwiązań rewitalizacyjnych zabytkowego mostu w Tczewie
PublicationPrzykłady koncepcji odbudowy przyczółka zachodniego zabytkowego mostu przez rzekę Wisłę w Tczewie wraz z zespołem bramnym. Ocena propozycji trzech rozwiązań rewitalizacyjnych mostu i wybór optymalnego pod względem finansowym i technologicznym. Czas i koszty budowy oraz wierność odbudowy zespołu bramnego mostu jako kryteria optymalizacji. Analiza w celu pozyskania środków finansowych potrzebnych na odbudowę, ale także adaptację...
-
Testing sensitivity of A-type residual current devices to earth fault currents with harmonics
PublicationIn many applications, modern current-using equipment utilizes power electronic converters to control the consumed power and to adjust the motor speed. Such equipment is used both in industrial and domestic installations. A characteristic feature of the converters is producing distorted earth fault currents, which contain a wide spectrum of harmonics, including high-order harmonics. Nowadays, protection against electric shock in...
-
Analytical procedures for short chain chlorinated paraffins determination - How to make them greener?
PublicationThe aim of the following paper was to gather current scientific information about the analytical protocols dedicated to measuring the content level of short-chain chlorinated paraffins (SCCPs) in various types of environmental samples. Moreover, the data about the basic validation parameters of applied procedures for SCCPs determination are listed. The main issue which is highlighted in the paper is the possibility of the application...
-
Problemy modernizacji szpitali
PublicationStale dokonujący się rozwój technologii medycznych oraz postęp w możliwościach leczniczych w sposób zasadniczy wpływa na kształt szpitala. W obecnie realizowanych szpitalach maleje powierzchnia działów pielęgnacji chorych, natomiast zwiększa się powierzchnia działów diagnostyczno-zabiegowych. Skraca się średni czas pobytu pacjenta w szpitalu. Szpital staje się sprawną „maszyną” do diagnozowania, a następnie leczenia pacjenta w...
-
Analiza następstw potencjalnej awarii wanty mostu podwieszonego w Bydgoszczy
PublicationMost Uniwersytecki został zamknięty po siedmiu latach od oddania do użytkowania. Powodem były widoczne gołym okiem objawy znacznego przeciążenia w obrębie zakotwień. Krytyczne elementy konstrukcji mostu zostały wzmocnione i przywrócono go do ruchu. W artykule przedstawiono nieliniowe analizy statyczne i dynamiczne wykonane na modelu MES, prezentujące cztery scenariusze przebiegu zachowania konstrukcji po utracie nośności mocowania...
-
A framework for risk matrix design: A case of MASS navigation risk
PublicationRisk matrix, a tool for visualizing risk assessment results, is essential to facilitate the risk communication and risk management in risk-based decision-making processes related to new and unexplored socio-technical systems. The use of an appropriate risk matrix is discussed in the literature, but it is overlooked for emerging technologies such as Maritime Autonomous Surface Ships (MASS). In this study, a comprehensive framework...
-
Concept of an Innovative Autonomous Unmanned System for Bathymetric Monitoring of Shallow Waterbodies (INNOBAT System)
PublicationBathymetry is a subset of hydrography, aimed at measuring the depth of waterbodies and waterways. Measurements are taken inter alia to detect natural obstacles or other navigational obstacles that endanger the safety of navigation, to examine the navigability conditions, anchorages, waterways and other commercial waterbodies, and to determine the parameters of the safe depth of waterbodies in the vicinity of ports, etc. Therefore,...
-
A method of determining and visualizing safe motion parameters of a ship navigating in restricted waters
PublicationThe paper presents a method of displaying ship collision avoidance information which is based on an unconventional Collision Threat Parameters Area (CTPA) technique. The solution presented here extends CTPA's functionality from past works by supporting navigation in restricted waters and handling ship domains analytically instead of numerically. It visualizes potential navigational threats as well as possible collision avoidance...
-
Biomass of macrophytobentos in the Puck Bay in 2010-2018
Open Research DataThe database contains data on qualitative composition and biomass of macrophytobenthos (flower plants and macroalgae) in samples collected in the Puck Bay area (Gulf of Gdańsk, southern Baltic Sea) at 20 stations between 2010-2018. The database contains information on sampling sites (region, geographical coordinates, depth), sample characteristics (date,...
-
Deflection measurement of field section with pavement with base course made of Cement Bitumen Treated Material Mixture C3E4 (28, 180, 270, 365 days after compaction)
Open Research DataDataset presents data of deflections determined for pavement with base course made of cold recycled mixture – cement bitumen treated material mixture with following binding agents: 3% cement, 4% emulsion (C3E4). Mixture was designed according to Polish requirements for the base course of pavement. Mixture was mixed in stationary plant and compacted...
-
Suspended matter, composition and fluxes, Gdansk Deep, late spring 2001
Open Research DataParticulate organic carbon (POC) and nitrogen (PON) concentrations and fluxes were measured in the Gdańsk Deep (Gulf of Gdansk) from 30.05 to 06.06.2001. The vertical profiles of POC and PON were characterised by the highest values in the euphotic layer, a gradual decrease with depth, and an increase below the halocline. The hydrophysical conditions...
-
Fatigue data of Cement Bitumen Treated Material Mixture C3E5.5 (Direct tension, over 28 days of curing at 20C)
Open Research DataFatigue data of Cement Bitumen Treated Material Mixture C3E5.5 (Direct tension, over 28 days of curing at 20C)
-
Depth profile of the composition of 8 nm Al2O3 thin film
Open Research Data8 nm layer of aluminum oxide (Al2O3) was deposited by ALD method on a s. Atomic layer deposition provides precise thickness control down to a single atomic layer. The precursors used were trimethylaluminum (Sigma-Aldrich) and purified water. The deposition of the atomic layer was carried out at 200 °C. To investigate the profile of concenration of...
-
BADANIA KOMPOZYTOWEGO MOSTU DLA PIESZYCH
PublicationThe paper presents in situ load testing of the innovative footbridge of FOBRIDGE grant mounted at Gdansk University of Technology. The span of composite sandwich structure (GFRP skins, PET core) and the scope of static and dynamic tests are presented. The selected, representative results of in situ measurements and data obtained from the SHM monitoring system are discussed. Besides the standard testing procedures on the full scale...
-
Maturity curve for estimating the in-place strength of high performance concrete
PublicationThe paper presents the maturity curve for estimating the in-place early-age compressive strength of concrete. The development of appropriate maturity curve is a complex process. It is important to correctly determine the datum temperature and activation energy, which can be obtained in mortar tests. This paper describes an investigation of the accuracy of the maturity method to estimate the strength when different way to rate constant...
-
Several notes on technical modernization of a historical building
PublicationThis paper describes methods and means used during the renovation process of several elements of a building – the assembly hall, inner courtyards and attics of the main building at Gdansk University of Technology, both in design and construction domains. A tissue of a historic building required special approach to these tasks, with special emphasis on good recognition of problems, careful planning and consistent implementing of...
-
UUV and AUV Vehicles as the autonomous systems for naval applications
PublicationThere is a growing pressure to investigate how to design and build the unmanned underwater vehicles of different types which are devoted towards performing many tasks under the water surface according to the data missions. During the recent years the Department of Ship Design and Subsea Robotics, Faculty of Ocean Engineering and Ship Technology, Gdansk University of Technology designed and built a few types of unmanned underwater...
-
Diagnostyka ultradźwiękowa mostowej belki prefabrykowanej typu T metodą młoteczkową
PublicationZastosowanie prefabrykacji w budowie obiektów mostowych pozwala optymalizować zużycie energii i materiałów i tym samym redukować koszty budowanego obiektu. Prefabrykowane belki sprężone mogą występować jako elementy kablobetonowe wykonywane bezpośrednio na placu budowy lub powstawać w zakładzie prefabrykacji jako elementy strunobetonowe. Elementy prefabrykowane wytwarzane w warunkach przemysłowych muszą spełniać wymagania wysokiej trwałości,...
-
The risk assessment of adverse events of nursing activities as the element of quality management in healhcare
PublicationThe purpose of the paper is to present MedCARVER+Shock method and Pareto analysis and its usability for the risk assessment of adverse events of nursing activities. 888 activities carried out by all 190 nurses working at the District Hospital X located in Poland were taken into account. During the research the qualitative approach was used. As the result sixteen groups of nursing activities causing the highest risk of adverse events...
-
Increasing efficiency of technological process by limiting impact of corrosive environment on operation of spiral classifiers
PublicationMost of the technological operations related to the preparation of the output to be enriched and to the production of the final copper concentrate take place with the use of water environment. Water management, besides using innovative technical and technological solutions, is a significant factor in the whole copper ore enrichment process. Mine water resources and surface water of the tailing pond named "Żelazny Most" are the...
-
Automatyczne urządzenia przełączające nn - oferta firmy Siemens
PublicationUkłady samoczynnego załaczania rezerwy zasilania (SZR), okrełslane w PN-EN 60947-6-1 jako automatyczne urządzenia przełaczające (ATSE ang. Automatic Transfer Switching Equipment) są przeznaczone do zapewnienia ciągłosci zasilania odbiorców energii elektrycznej. W artykule omówiono klasyfikację ATSE, budowę blokad aparatów wykonawczych oraz zalecane czasy zadzialania ATSE. Przedstawiono automatyczne urządzenia przełaczające oferowane...
-
Automatyczne urządzenia przełączające niskiego napięcia
PublicationUkłady samoczynnego załaczania rezerwy zasilania (SZR), okrełslane w PN-EN 60947-6-1 jako automatyczne urządzenia przełaczające (ATSE ang. Automatic Transfer Switching Equipment) są przeznaczone do zapewnienia ciągłosci zasilania odbiorców energii elektrycznej. W artykule omówiono klasyfikację ATSE, budowę elektrycznych blokad aparatów wykonawczych oraz zalecane czasy zadzialania ATSE. Przedstawiono automatyczne urządzenia przełaczające...
-
Selective Laser Melting of Ti Alloy for Manufacturing The Prosthetic Elements
PublicationThe selective laser melting (SLM) is the additive manufacturing method of custom-designed parts. The used materials and the applications are various, including medicine. The titanium and its alloys are materials for which the dimensional quality, surface smoothness and no or extremely low porosity are difficult to reach. In this paper, the successful attempt to obtain by SLM the individually designed prosthetic bridges is described....
-
Decision making process using deep learning
PublicationEndüstri 4.0, dördüncü endüstri devrimi veya Endüstriyel Nesnelerin İnterneti (IIoT) olarak adlandırılan sanayi akımı, işletmelere, daha verimli, daha büyük bir esneklikle, daha güvenli ve daha çevre dostu bir şekilde üretim yapma imkanı sunmaktadır. Nesnelerin İnterneti ile bağlantılı yeni teknoloji ve hizmetler birçok endüstriyel uygulamada devrim niteliği taşımaktadır. Fabrikalardaki otomasyon, tahminleyici bakım (PdM – Predictive...
-
Numerical simulation of hardening of concrete plate
PublicationThe paper presents a theoretical formulation of concrete curing in order to predict temperature evolution and strength development. The model of heat flow is based on a well-known Fourier equation. The numerical solution is implemented by means of the Finite Difference Method. In order to verify the model, the in situ temperature measurements at the top plate of a road bridge were carried out. A high agreement between numerical...
-
Dynamic Response of the Suspended on a Single Cable Footbridge
PublicationThe article presents numerical simulations, dynamic in situ load tests and a structural health monitoring (SHM) system installed in a suspended on a single cable footbridge. Numerical simulations performed prior to construction indicated the possibility of structural dynamics problems, finally confirmed in the course of dynamic test loading. In the dynamic load course the bridge deck developed vibrations displaying accelerations...
-
Mechanical Recycling via Regrinding, Rebonding, Adhesive Pressing, and Molding
PublicationIncreasing amount of polyurethane foams waste (e.g. from the building or furniture industry) produced every year resulted in the intensive development of their recycling methods. This chapter covers most important mechanical recycling methods, i.e. regrinding, rebonding, adhesive pressing, and molding. The procedure, required equipment and chemicals (if needed) for each method were described. The possible applications of the products...
-
Improving web user experience with caching user interface
PublicationOften, Web technologies are used to operate or to configure network-enabled equipment, to configure and administer modular applications, or as teaching environments. The comfort of human work requires a similar response time in these applications as in the Internet. To improve response time, various forms of caching at different levels are employed. To improve the user experience in regard to response time when performing specific...
-
Start-up of a power unit of a thermal power plant auxiliary systems with supply from a hydropower plant
PublicationThis article discusses the issues related to a power unit of a thermal power plant start-up with the use of a hydropower plant. Hydropower plant can supply and will enable start-up of auxiliary equipment in a power unit of a thermal power plant. Due to high capacity of auxiliary drives, start-up of auxiliaries in a thermal power plant after blackout (and boiler shutdown) is not possible from emergency energy sources in the power...
-
NEW TRENDS IN DEVELOPMENT OF ORC'S FOR MICROPOWER GENERATION
PublicationIn the paper, new trends in development of micropower generation of heat and electricity are presented. New type of CHP for domestic usage is developed in the Institute of Fluid-Flow Machinery PAS and methods of its design are presented. The most promising trends in equipment of ORC cycle for this purpose were discussed. Main attention was focused on micro-heat exchangers design based on micro-channels and micro-jets. In our opinion...
-
Autonomous Battery Drive in Trolleybuses: an Overview of Practical Examples
PublicationBattery electric buses are believed to be means of transportation of the future. However, despite the continuous development of electrochemical batteries technology and the multitude of electric buses on offer, it is still no proved solutions that can be widely used. Charging is the one of the weakness point of the electric buses. Trolleybuses are alternative for them. Especially, trolleybuses equipment with traction batteries...
-
MOST PODWIESZONY kreowanie przestrzeni i konsekwencje konstrukcyjne
PublicationProjektowanie i budowa - wyzwania dla projektantów i wykonawców mostów. Mosty podwieszone i wiszące ich estetyka i konsekwencje strukturalne. Artykuł dotyczy aspektów estetycznych i konstrukcyjnych zaprojektowanych pylonów dla mostów podwieszonych lub wiszących. Autor zwraca uwagę na fakt, że niezwykłe rozwiązanie konstrukcyjne zastosowane do kładki lub małego wiaduktu może działać prawidłowo dzięki zjawiskom efektu skali. Nadzwyczajne...
-
An Integrated Approach to an Assessment of Bottlenecks for Navigation on Riverine Waterways
PublicationWater transport, both sea and inland, is the cheapest, least invasive, and safest option for non-standard loads; hence, it is important to increase the percentage share of inland waterway transport on the rivers of Central and Eastern Europe. Transporting cargo is particularly difficult on shallow waterways because rivers overloaded with sediment determine the vertical parameters on inland waterways. A ship’s safe manoeuvrability...
-
Probabilistic seismic assessment of RC box-girder highway bridges with unequal-height piers subjected to earthquake-induced pounding
PublicationThis paper uses the probabilistic seismic assessment to study the effects of pounding and irregularity on the seismic behavior of typical concrete box-girder bridges with four levels of altitudinal irregularity. To extend the results for all bridges in the same class, uncertainty related to the earthquake, structural geometries, and materials are considered. Pounding is likely to take place in two cases: the first one concerns...
-
Wykorzystanie mediów społecznościowych do promocji otwartości w badaniach naukowych na przykładzie Biblioteki Politechniki Gdańskiej
PublicationMedia społecznościowe są jednym ze sposobów na skuteczną promocję zasobów oraz usług bibliotecznych w obecnym świecie cyfrowym. Stanowią również niedocenianą możliwość komunikacji pomiędzy naukowcami, bibliotekarzami a czytelnikami. Biblioteka akademicka może aktywnie angażować się w proces upowszechniania dorobku naukowego uczelni, podejmując w tym celu różnorakie działania marketingowe, wykorzystując takie serwisy jak: Facebook,...
-
Tripping of F-type RCDs for High-Frequency Residual Currents
PublicationResidual current devices (RCDs) are apparatus commonly used for protection against electric shock in low-voltage electrical installations. They protect people in the case of an earth fault or even in the case of direct contact with the live parts. However, to be effective protective devices, RCDs have to detect residual currents of various waveform shapes which appear in modern electrical installations. For this purpose, RCDs...
-
Tripping of F-type RCDs for high-frequency residual currents
PublicationResidual current devices (RCDs) are apparatus commonly used for protection against electric shock in low-voltage electrical installations. They protect people in the case of an earth fault or even in the case of direct contact with the live parts. However, to be effective protective devices, RCDs have to detect residual currents of various waveform shapes which appear in modern electrical installations. For this purpose, RCDs are...
-
Reception of Terrestrial DAB+ and FM Radio with a Mobile Device: A Subjective Quality Evaluation
PublicationNowadays, terrestrial broadcasting enables to receive content anytime and everywhere. People can obtain information both with a portable or desktop receiver, which include pocket-sized devices as well as high-end Hi-Fi equipment, not to mention car audio systems. Numerous manufacturers include FM-compatible chipsets in a variety of user equipment (UE), including mobile phones. However, digital radio signal processing modules, such...