Search results for: low-load capacity roof
-
Validation of atmospheric aerosols parallel sampling in a multifold device
PublicationIn this work, particulate matter was collected using an active sampling system consisting of a PM10 (<10 μm) inlet coupled to a multifold device containing six channels, connected to a vacuum pump. Each channel was equipped with a filter holder fitted with adequately chosen filters. The system was fixed on a metallic structure, which was placed on the roof of the laboratory building, at the Faculty of Sciences, in Lisbon. Sampling...
-
Optimization of Stabilizing Systems in Protection of Cultural Heritage: The Case of the Historical Retaining Wall in the Wisłoujście Fortress
PublicationThe aim of the paper is to propose new quantitative criteria for selecting the optimal method of securing and repairing a historical object, which take into account Structural, Conservation and Architectural aspects (the S–C–A method). Construction works on cultural heritage sites tend to be challenging and require an interdisciplinary approach. Therefore, they are strictly related to the philosophy of sustainable development which...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublicationIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Evaluation of Street Lighting Efficiency Using a Mobile Measurement System
PublicationThe issue concerns the initial stage of work on a method for performing a rapid assessment of the energy efficiency and illuminance of a street lighting installation. The proposed method is based on simultaneous measurement of illuminance from three lux meters placed on the roof of the vehicle. The data are acquired in road traffic, while the vehicle is driving. The proposed solution will allow in the future to quickly and reproducibly...
-
Edgewise Compressive Behavior of Composite Structural Insulated Panels with Magnesium Oxide Board Facings
PublicationEdgewise compression response of a composite structural insulated panel (CSIP) with magnesium oxide board facings was investigated. The discussed CSIP is a novel multifunctional sandwich panel introduced to the housing industry as a part of the wall, floor, and roof assemblies. The study aims to propose a computational tool for reliable prediction of failure modes of CSIPs subjected to concentric and eccentric axial loads. An advanced...
-
Stabilizing forces in trapezoidal sheeting used as a part of the bracing system
PublicationIn the analysis of bracing systems imperfections of the restrained elements should be considered. According to EC3 this effect can be calculated by means of the equivalent stabilizing force, which replaces (in simplified way) initial bow imperfection of the braced element. However, alternative suggestions of the equivalent stabilizing force calculations can be also found in the literature. In this paper segment of the pitched roof...
-
Acceleration of Electromagnetic Simulations on Reconfigurable FPGA Card
PublicationIn this contribution, the hardware acceleration of electromagnetic simulations on the reconfigurable field-programmable-gate-array (FPGA) card is presented. In the developed implementation of scientific computations, the matrix-assembly phase of the method of moments (MoM) is accelerated on the Xilinx Alveo U200 card. The computational method involves discretization of the frequency-domain mixed potential integral equation using...
-
Educational and cognitive aspects of adaptation of nonuse spaces in monumental sacral objects.
PublicationThe area of attics and towers in historic churches in Europe are yet quite inaccessible places for visitors, shrouded in the atmosphere of mysticism, hiding many secrets. Introduction of the new public function into the non-used zones of the monumental sacral objects has many aspects including educational and cognitive ones which are discussed in the following article. The article indicates items that can be found in the zone above...
-
WHY SHOULD WE ADOPT NON-USED ATTICS OF MONUMENTAL SACRAL CATHOLIC CHURCHES FOR SECULAR PURPOSES?
PublicationA motive for adapting the desecrated churches to new purposes is a broadly discussed matter, progressively better investigated and defined. Is it advisable to introduce a new, permanent function, complementary to the sacred one in the historical ecclesial buildings? This paper presents the results of the research on benefits of adapting the non-utilized attics of monumental churches still performing their sacred function, located...
-
Algorithm for Automatic Wear Estimation of Railway Contact Strips Based on 3D Scanning Results
PublicationElectric rail vehicles use current collection system which consists of overhead contact line and a current collector (pantograph) mounted on the roof of a vehicle. A pantograph is equipped with contact strips, which slide along the contact wire, ensuring steady electric contact. Contact strips are made of carbon layer, fixed to an aluminum carrier. The carbon layer wears down due to friction. Using overly worn contact strips increases...
-
Issues relating to the efficient Application of passive solar protection in multi-family residential buildings
PublicationThe following article is intended to discuss the issues concerning the introduction of passive measures aimed at improving solar protection in multi-family buildings. A system of classifying these methods into two groups of solutions (architectural and material-building) was applied. The first group includes issues concerning facade design, the spatial features of which (such as loggias, balconies and other overhangs) can be treated...
-
Seismic Response Analysis of Knee-Braced Steel Frames Using Ni-Ti Shape Memory Alloys (SMAs)
PublicationShape Memory Alloys (SMAs) are known as active materials that can be widely used for structural purposes due to their flag-shape behavior under loading and reloading. Their unique characteristics provided a potential solution for civil engi-neers especially to model buildings with the capability of dissipating seismic en-ergy. In this study, the main purpose is to explore the seismic behavior of Knee-Braced Frames (KBFs) and...
-
STORMWATER AS AN ALTERNATIVE WATER SOURCE: QUALITY CHANGES WITH RAINFALL DURATION AND IMPLICATIONS FOR TREATMENT APPROACHES
PublicationThe pressure on the world’s water resources is rapidly increasing due to population growth and climatic changes. Valorisation of stormwater as a water resource for non-potable reuse can reduce high-quality water demands and save it for potable uses. In this context, not only roof runoff but also drained stormwater outflow, representing considerably higher pollution levels, should be considered as a potential resource. We analysed...
-
Development of fragility curves in adjacent steel moment-resisting frames considering pounding effects through improved wavelet-based refined damage-sensitive feature
PublicationFragility curves present useful information related to earthquake-induced probability assessment of steel moment-resisting frames (MRFs) and determine the probability of the damage exceedance at different floor levels of MRFs. The review of the literature shows that most of the previous studies dealing with the fragility curves were based on conventional measures, such as spectral acceleration at the first mode period, peak...
-
POSSIBILITIES OF ELECTRICAL ENERGY GENERATION IN PHOTOVOLTAIC SYSTEMS INSTALLED IN CENTRAL EUROPE
PublicationNowadays, fossil fuels are the main sources of energy from which electricity is obtained. But these sources will not last forever, so in due course renewable energies will have to replace them in this role. One of these new sources is solar energy. To generate electricity from sunlight, solar (photovoltaic - PV) cells and modules are used. The increasing interest in PV cells and modules worldwide is due mainly to the fact that...
-
Field investigation of low-temperature cracking and stiffness moduli on selected roads with conventional and high modulus asphalt concrete
PublicationHigh Modulus Asphalt Concrete (HMAC) was introduced in Poland as a one of the solutions to the problem of rutting, type of deterioration common in the 1990s. After first encouraging trials in 2002 HMAC was widely used for heavily loaded national roads and motorways. However some concerns were raised about low-temperature cracking of HMAC. This was the main reason of the studies presented in this article were started. The article...
-
Medieval Bourgeois Tenement Houses as an Archetype for Contemporary Architectural and Construction Solutions: The Example of Historic Downtown Gdańsk
PublicationThe basic urban tissue of medieval European cities consisted of brick townhouses. In the cities of northern Europe, these tenements were characterised by a block based on an elongated rectangular plan, covered with a gable roof with a ridge oriented perpendicularly to the street. The side walls of the tenement house were common for both neighbours and constituted a basic structural element. The gable façades were not loaded with...
-
Performance Analysis and Quantification of BeiDou Navigation Satellite System (BDS-3)
PublicationPositioning, Navigation, and Timing (PNT) information play a vital role in everyday life of common persons. People greatly rely on Global Navigation Satellite System (GNSS)-enabled applications for navigation to reach their desired destination. However, GNSS navigation performance is highly degraded in urban environments due to the high probability of signal interruption, multipath (MP), and/or non-line-of-sight (NLOS) signal...
-
Ryszard Katulski prof. dr hab. inż.
People -
Experimental Testing of Innovative Cold-Formed "GEB" Section / Badania Eksperymentalne Innowacyjnego Kształtownika Giętego Na Zimno Typu „Geb“
PublicationOne of the major advantages of light gauge steel structures made of cold-formed steel sections is their low weight, so manufacturers are increasingly using the possibilities of those sections for the production of typical single-storey steel structures systems. Well known profiles, such as Z, C and the so called hat sections that have been studied and described in the literature, are used mainly as purlins or truss components....
-
Water-Lubricated Sintered Bronze Journal Bearings—Theoretical and Experimental Research
PublicationWater lubricated bearings are used from many years in shipbuilding, hydro power and other industries because of their advantages such as: extensive serviceable life, low coefficient of friction, longevity of shaft sleeve, good abrasion resistance, low maintenance required, unit simplicity, no danger of pollution and low price. Various types of water lubricated sliding bearings have been tested at the Technical University of Gdansk...
-
Vibro piles performance prediction using result of CPT
PublicationVibro piles belong to the group of full displacement piles with an expanded base, characterised by a very high load capacity, especially in non-cohesive soils. The problem is to adopt a reliable method for the determination of full load–settlement (Q–s) curve. A frequent difficulty is the determination of the load capacity limit based on the static load test because the course of the load–settlement curve is of a linear nature....
-
Innovative Cold-formed GEB Section under Bending
PublicationThis paper is concerned with the numerical bending capacity study of the innovative cold-formed GEB sections. Both linear buckling analysis and non-linear static analysis incorporating geometric and material nonlinearity were carried out employing a shell structural model. The magnitudes of buckling load and limit load with respect to GEB section depth and thickness were obtained. The opened cold-formed section was tested assuming...
-
Simulation of large thrust-bearing performance at transient states, warm and cold start-up
PublicationThe start-up of a large hydrodynamic thrust bearing of a vertical hydrogenerator is one of the most critical situations during the lifetime of a bearing. Hydrodynamic load capacity is low due to low speed and higher thermal deformations of the pad. A new approach to the simulation of a hydrodynamic bearing is shown in this article. A combination of finite elements method and computational fluid dynamics is used to perform the transient...
-
The use of GFRP tubes as load-bearing jackets in concrete-composite columns
PublicationThe paper presents the fields of applications of polymer composites in building structures. The use of composite glass fibre tubes is discussed in more detail. The laboratory methods used to test the mechanical properties of these pipes are presented. An original research program is presented, including six concrete-filled glass fibre tubes. The cylinders and columns made in this way were tested for their axial load capacity. Conclusions...
-
Overheating of underground power cable line due to its partial exposition to solar radiation
PublicationCurrent-carrying capacity of underground power cable lines depends, among others, on thermal resistivity of the soil and cables layout: trefoil formation, flat formation with or without spacing. If conditions for heat transfer in the ground are favorable, the current-carrying capacity is relatively high. Therefore, it generates risk of the power cables overheating, if part of the cable line is located vertically in the air, to...
-
Prediction of pile shaft capacity in tension based on some direct CPT methods – Vistula Marshland test site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with a diameter of 0.4 m and the length...
-
Displacement piles - classification and methods for the calculation of bearing capacity.
PublicationDisplacement piles belong to a group of technologies whose main idea is to install or make a pile without extracting ground material. According to definition, contained in PN-EN:1997-1:2008, displacement piles should be considered as driven, pressed in using vibrators and made with the use of spread augers. The classification of piles used so far with regard to the technology of execution is modified. An additional element is the...
-
Structural Reliability Assessment Of Corroded Tanker Ship Based On Experimentally Estimated Ultimate Strength
PublicationThis work deals with the reliability assessment of a tanker ship hull structure subjected to a vertical bending moment and corrosion degradation. The progressive collapse and ultimate load carrying capacity are estimated based on experimentally tested scaled box-shaped-specimens. The translation of the strength estimate of the scaled specimen to the real tanker ship hull structure is performed based on the dimensional theory developing...
-
Acoustic journal bearing - A search for adequate configuration
PublicationClassical non-contact bearings are already used in a number of specialist applications but there are somespecialist areas where they cannot be used for variety of reasons and acoustic sliding bearings could be an alternative. The paper presents the quest for a configuration of an acoustic journal bearing and shows that the overall shape of the bearing and its geometry are of a vital importance for the load capacity oft he bearing....
-
Study on 19th-century cast iron columns from the former financial office building in Kwidzyn
PublicationThe article presents the results for cast iron columns used as floor supports in the former financial office building in Kwidzyn (Poland).The stocktaking drawings provided the general and detailed data about the 19th century designer’s decisions. During the research, architectural and structural analysis was carried out. The graphics were used as a starting material for preparing 3D calculation models. The FEM-based numerical simulations...
-
Implementacja pomierzonych imperfekcji geometrycznych powłokicylindrycznej do modelu obliczeniowego
PublicationThis paper presents the method of implementation of the geometrical imperfections used by the author during the experimental and numerical research into the load-carrying capacity of cylindrical steel shells subjected to uniform circumferential compression.
-
OPERATING CONDITIONS OF SLIDE BEARINGS OF MILLS USED IN KGHM POLSKA MIEDŹ S.A.
PublicationThe paper contains the results from a tec hnical analysis of the conditions of the operation of hydrodynamic bearings supporting the drums of ore processing mills at KGHM Polska Mied ź S.A. A theoretical analysis was performed on the grounds of onsite examination and measurem ents of principal dimensions of the bearings of interest. The computer simulation covered the characteristics of the oil film in the bearings...
-
Prediction of Pile Shaft Capacity in Tension Based on Some Direct CPT Methods—Vistula Marshland Test Site
PublicationThis paper presents different CPT methodologies for the prediction of the pile shaft resistance in tension on the example of three reference screw piles of the Jazowa test site in Poland. The shaft capacity was estimated based on the cone resistance, sleeve friction and CPT excess pore water pressure. Three piles with diameter 0.4 m and the length varied from 8 m to 14.6 m were subjected to static load tests in tension. Their...
-
Combined thrust radial bearing of a submarine main shaft – Design and analysis of failure
PublicationThis paper presents an analysis of the combined thrust radial bearing of a submarine propulsion shaft. The lubrication system of the bearing is based on a fixed ring. The efficiency of the lubrication system depends on the shaft speed and temperature, which affects oil viscosity. In turn, the thrust bearing load also depends on the rotational speed of the shaft, because as the speed increases, the drag of the ship increases simultaneously,...
-
Numerical analysis on axial capacity of steel built-up battened columns
PublicationThis paper deals with the numerical analysis aimed at study the bearing capacity of pinended steel built-up columns under axial compression. Finite element (FE) models were performed for the columns presented in the literature. The main problem discussed in the article is the shape and magnitude of geometric imperfections introduced into the numerical FE model, necessary to obtain the load capacity consistent with the experimental...
-
Simulation Results of Dynamic Capacity Reallocation in Hierarchical Cell Structure of UMTS Network
PublicationIn the paper simulation results of dynamic capacity reallocation between different layers of hierarchical cell structure of UMTS network has been described. This approach for load management seems to be useful for improving the resource utilization perfmorance.
-
Badania eksperymentalne słupów CFST z betonem zwykłym i ekspansywnym
PublicationPraca przedstawia badania eksperymentalne ponad 40 słupów CFST. Analizie poddano wyniki siły niszczącej słupy w aspekcie grubości stalowego płaszcza, smukłości słupa, rodzaju betonu wypełniającego stalową rurę (zwykły i ekspansywny) i jego wytrzymałości a także sposobu obciążania słupa (przez rdzeń lub przez cały przekrój). Sprawdzono efektywność słupów CFST z użyciem betonu ekspansywnego i zwykłego rozumianą jako stosunek nośności...
-
INFLUENCE OF TIME ON THE BEARING CAPACITY OF PRECAST PILES
PublicationOne of the most popular types of foundations in layered subsoil with very differentiated soil shear strengths are precast piles. One of the reasons is a fact that we can well control the driving process during the installation of these piles. The principles of the assessment of bearing capacity and settlements of the piles given by Eurocode 7, concentrate on two main methods, i.e. Static Pile Load Tests (SPLT) and Dynamic Driving...
-
Influence of bush wear in water lubricated marine stern tube bearings with shaft misalignment
PublicationWater lubricated propeller shaft bearings are frequently employed on modern ships due to their advantages such as durability, simplicity and low price. Specific working conditions on ships cause shaft misalignment which often results in rapid wearing of bush and shaft. Shaft misalignment could be an effect of manufacturing or assembly faults but sometimes it appears due to hull or shaft deformation. The wearing process has influence...
-
RESEARCH ON HYDRODYNAMIC PEEK JOURNAL BEARINGS LUBRICATED WITH WATER AND OIL
PublicationThe main purpose of the research was to determine the possibilities and experimentally test the benefits of replacing conventional oil lubrication with ecological water lubrication. Tests were carried out on a test rig for hydrodynamic radial bearings under conditions representative of the expected applications for the bearing in water turbines. Bearings made from the polymer material PEEK (polyether ether ketone) were tested under static...
-
Ground anchors diagnostic process based on elastic wave propagation method
PublicationThe paper is focused on analysis of elastic wave propagation in the context of diagnostics of ground anchors. Numerical simulations were performed to assess the possibility of evaluation of the anchorage quality. It was assumed that the quality and the load capacity of the anchor system directly depend on the length, on which mortar and steel cooperate.
-
Centrally Pivoted Tilting Pad Thrust Bearing with Carbon-Based Coated Collar—Experimental Results of Low- and Medium-Speed Operation
PublicationExperimental results of the research on a tilting pad thrust bearing with symmetrical pad support in the conditions of high loads and low speeds are presented in the paper. As described in the literature review, experimental results of tilting pad bearings at low speed/high load regime and transient conditions are rare. Unusual material selection - steel pad against a DLC-type coating on the collar was utilized. Such material combination...
-
Discrete random variables in reliability calculations of a reticulated shell
PublicationImplementation of the Point Estimation Method (PEM) in the reliability analysis of a three-dimensional truss structure is presented in the paper. The influence of geometric and material random parameters on the truss load-carrying capacity was investigated. The analysis was performed for different combinations of basic variables. Symmetric and asymmetric cases of snow load were taken to assess the structural reliability. Sensitivity...
-
Zagrożenie katastrofą budowlaną Mostu Uniwersyteckiego w Bydgoszczy. Analiza i badania
PublicationMost Uniwersytecki został zamknięty po 7 latach od oddania do użytku. Powodem były błędy projektowe ujawnione w przeglądzie w roku 2020, potwierdzone teoretycznymi analizami nośności. Bezpośrednim powodem zamknięcia przeprawy było stwierdzenie zagrożenia katastrofą budowlaną. W roku 2021, zgodnie z zaleceniem i koncepcją ekspercką, krytyczne elementy konstrukcji mostu zostały wzmocnione. W styczniu 2022 most został przywrócony...
-
Innovative cold-formed GEB section under compression
PublicationCold-formed steel sections extensively affect the modern steel construction industry. Not only are they used as secondary elements like purlins or sheeting, but also they can serve as primary load-bearing members in fabricated steel panels and trusses. A new cross-section called shortly a GEB may serve as that member. However, its existence of the metal building structures industry depends on the exact, optimal dimensional parameters...
-
Correlation between natural frequencies and buckling load in a stiffened shell
PublicationThe paper deals with correlation between natural frequencies and buckling load of a stiffened shell composed of corrugated sheets and vertical stiffeners (columns). The simplified shell segment represents the buckling behaviour of a whole silo with sparsely distributed columns. The paper covers variants of linear buckling anal-yses, dynamic eigenvalue analyses and geometrically non-linear analyses of a segment modelled with shell...
-
Application of the ‘CPT 2012’model of AFNOR standard for column design in Poland–Jazowa case study
Publicationhis paper presents the ‘CPT 2012’ model incorporated into the AFNOR NF P94-262:2012-07, French standard for pile design fully compatible with Eurocode 7, to the wider Polish audience. The bearing capacity of three reference columns for Vistula Marshlands have been calculated according to ‘CPT 2012’ model and AFNOR recommendations. Then, the design resistances have been compared with ultimate column bearing capacity measured during...
-
Bearing capacity of the working platform with kinematic method
PublicationBearing capacity of the working platform for heavy tracks was analysed using Distinct Layout Optimization (DLO) method. The platform layer constructed from cohesionless soils is resting on weak cohesive subgrade. Different thickness of the platform, its effective angle of internal friction and undrained shear strength of the soft soil were taken into consideration. Kinematic method permits different failure mechanisms to be analyzed....
-
Concrete-filled FRP tubular members in marine and bridge structures
PublicationConcrete core of the concrete-filled tubes (CFTs) with circular cross-section is in the case of an axial compression subjected to a spatial state of compressive stresses. This state leads to enhancement in the concrete strength. The enhancement is utilized in Eurocode 4 design procedures for CFSTs (i.e. CFTs with tube made of steel). The structural design of CFFTs (i.e. CFTs with tube made of Fibre Reinforced Polymer - FRP) is...