Filters
total: 760
filtered: 700
Search results for: GEOPOLYMER CONCRETE
-
Guided Wave Propagation in Detection of Partial Circumferential Debonding in Concrete Structures
PublicationThe following article presents results of investigating the damage detection in reinforced concrete beams with artificially introduced debonding between the rod and cover, using a non-destructive method based on elastic waves propagation. The primary aim of the research was to analyze the possible use of guided waves in partial circumferential debonding detection. Guided waves were excited and registered in reinforced concrete...
-
Safety assessment of a concrete viaduct damaged by vehicle impact and an evaluation of the repair
PublicationDamage to lower parts of viaducts caused by impact from under-passing high vehicles is relatively frequent. One such incident, in which a viaduct was damaged by the impact from a truck with an improperly assembled hydraulic crane, is considered in this work. The analysis is based on a detailed object damage evaluation, 3D laser scanning, and numerical simulations. The aim of the study is to accurately model the vehicle impact into...
-
A novel heterogeneous model of concrete for numerical modelling of ground penetrating radar
PublicationThe ground penetrating radar (GPR) method has increasingly been applied in the non-destructive testing of reinforced concrete structures. The most common approach to the modelling of radar waves is to consider concrete as a homogeneous material. This paper proposes a novel, heterogeneous, numerical model of concrete for exhaustive interpretation of GPR data. An algorithm for determining the substitute values of the material constants...
-
The use of GFRP tubes as load-bearing jackets in concrete-composite columns
PublicationThe paper presents the fields of applications of polymer composites in building structures. The use of composite glass fibre tubes is discussed in more detail. The laboratory methods used to test the mechanical properties of these pipes are presented. An original research program is presented, including six concrete-filled glass fibre tubes. The cylinders and columns made in this way were tested for their axial load capacity. Conclusions...
-
BEHAVIOR OF REINFORCED CONCRETE BEAMS CONTAINING LIGHTWEIGHT AGGREGATE IN THE TENSILE ZONE
Publication.
-
The Influence of the Aircraft Operating Fluids on the Mechanical Parameters of the Airport Surface Concrete
PublicationThe authors of the article assessed the impact of operating fluids used to service aircraft on changing mechanical parameters of cement concrete intended for airport pavement. The research concerned concrete designed with the use of CEM I 42.5N LH NA low-alkali cement, broken granite aggregate, fine washed aggregate, and admixtures. The analysis included the assessment of changes in dierences in endurance parameters over various...
-
RMS-based damage detection in reinforced concrete beams: numerical simulations
PublicationImage-based damage detection methods using guided waves are well known and widely applied approaches in structural diagnostics. They are usually utilized in detection of surface damages or defects of plate-like structures. The article presents results of the study of applicability of imaging wave-based methods in detection in miniscule internal damage in the form of debonding. The investigations were carried out on numerical models...
-
Evaluation of reinforcement corrosion rate in concrete structures by electrochemical noise measurements
PublicationW pracy przedstawiono wyniki obliczeń rezystancji polaryzacyjnej w układzie złożonym z dwóch elektrod (ze stali węglowej oraz elektrody odniesienia), umieszczonych w otulinie betonowej. Szybkość korozji ulega zmianom uzależnionym od stopnia nasiąknięcia betonu roztworem zawierającym jony chlorkowe. Zmiany rezystancji polaryzacyjnej elektrody stalowej oceniane są na podstawie pomiarów prądowego i potencjałowego szumu elektrochemicznego....
-
FE-modelling of strain localization in concrete with coupled elasto-plasticity and damage
PublicationW artykule przedstawiono wyniki numerycznej dla zginania belki betonowej przy zastosowaniu modelu sprężysto-plastycznego, modelu z degradacja sztywności i modelu połączonego sprężysto-plastycznego z degradacją sztywności. Wszystkie modele rozszerzono o długość charakterystyczną mikrostruktury za pomocą teorii nielokalnej.
-
Experimental investigations of size effect in reinforced concrete beams failing by shear
PublicationW artykule omówiono wyniki doświadczalne efektu skali w zbrojonych betonowych belkach niszczących się przez ścinanie. Doświadczenia wykonano dla belek o różnych wymiarach ze zbrojeniem stalowym i bazaltowym. Podczas doświadczeń pomierzono siłę oraz szerokości lokalizacji i rys. Wyniki porównano z modelem skali wg Bazanta.
-
Application of DIC technique to concrete - study on objectivity of measured surface displacements
PublicationArtykuł omawia wyniki pomiarów szerokości lokalizacji odkształceń na powierzchni betonu podczas zginania belek. Wykonano obszerne studia nad obiektywnością pomierzonych przemieszczeń w betonie. Opracowano własna metodę do obliczeń szerokości lokalizacji.
-
J. FE modelling of cracks in concrete elements within continuum mechanics.
PublicationW artykule przedstawiono wyniki symulacji rys zakrzywionych w elementach betonowych w warunkach mieszanego sposobu obciążenia. Symulacje wykonano przy zastosowaniu 3 różnych modeli: modelu sprężysto-plastycznego, modelu w ramach mechaniki zniszczeniowej i modelu z rysami obracającymi się.
-
Multi-scale modelling of concrete beams subjected to three-point bending
PublicationW artykule przedstawiono wyniki numeryczne MES dwuskalowego modelowania belek betonowych z nacięciem na poziomie skali makro i mezo. Obliczenia wykonano przy wykorzystaniu modelu degradacji sztywności z nielokalnym osłabieniem. Beton został opisany na poziomie skali mezo jako stochastyczny materiał 3-składnikowy złożony z kruszywa, zaczynu cementowego oraz stref kontaktu. Natomiast na poziomie skali makro został opisany jako materiał...
-
Investigations of size effect in tensile fracture of concrete using a lattice model
PublicationArtykuł przedstawia symulacje efektu skali w betonie podczas rozciągania przy zastosowaniu nowego modelu siatkowego. Zbadano wpływ rozkładu i wielkości kruszywa oraz wpływ strefy kontaktu na efekt skali.
-
Early prediction of macrocrack location in concrete and other granular composite materials
PublicationHeterogeniczne kruche kompozyty, takie jak beton, ceramika i skały składają się z ziaren połączonych wiązaniami. Pytanie, czy ścieżka pęknięcia, która prowadzi do zniszczenia może być przewidziania na podstawie znanych cech mikrostrukturalnych, a mianowicie łączności wiązań, rozmiaru, energii pękania, wytrzymałości pozostają otwarte. Istnieje wiele kryteriów pęknięć. Najczęściej używane są oparte na postulowanym ekstremum naprężenia...
-
Modeling of capillary fluid flow in concrete using a DEM-CFD approach
PublicationSformułowano połączone podejście do modelowania dwufazowego przepływu wody napędzanego hydraulicznie i kapilarnie w nienasyconym betonie. Proces przepływu analizowano numerycznie w mezoskali w warunkach dwuwymiarowych (2D), łącząc metodę elementów dyskretnych (DEM) z obliczeniową dynamiką płynów (CFD) w warunkach izotermicznych. Przeprowadzono w pełni sprzężone hydromechaniczne testy symulacyjne na małych próbkach betonu o uproszczonej...
-
Numerical analysis of behaviour of reinforced concrete elements under eccentric compression
PublicationPrzedstawiono wyniki modelowania nośności elementów żelbetowych stosując metodę elementów skończonych. Do opisu betonu zastosowano sprężysto-plastyczne prawo materiałowe wg Druckera-Pragera. Do modelowania stali zbrojeniowej zastosowano sprężysto-plastyczne prawo materiałowe według von Misesa. Obliczenia wykonano dla ścian żelbetowych.
-
A Non-local elasto-plastic model to describe localisations of deformation in concrete
PublicationPrzedstawiono wyniki numerycznej symulacji lokalizacji odkształceń stosując metodę elementów skończonych na bazie nielokalnego prawa sprężysto-plastycznego dla betonu. Prawo wykorzystuje długość charakterystyczną. Obliczenia dla ściskania jednoosiowego pokazały, że wyniki numeryczne nie zależą od siatki MES. Osiągnięto pełną regularyzację problemu brzegowego.
-
Biowaste chicken eggshell powder as a potential cure modifier for epoxy/anhydride systems: competitiveness with terpolymer-modified calcium carbonate at low loading levels
PublicationBiowaste chicken eggshell (ES) powder was applied as a potential cure modifier in epoxy/anhydride systems. Cure behaviour and kinetics of composites filled with very low content (0.1 wt% based on epoxy resin) of ES, calcium carbonate (CaCO3), and terpolymer-modified fillers, mES and mCaCO3, were discussed comparatively. Surface analysis was performed by X-ray photoelectron spectroscopy. Cure kinetics was investigated by differential...
-
Synthesis, characterization and application of cross-linked functional terpolymer through epoxy group as sorbent for extraction of cadmium from waters and foods: Multivariate optimization
PublicationThe purpose of this study was to develop a selective sorbent for cadmium ions (Cd(II)) enrichment in orbital shaker assisted solid phase microextraction (OS-SPME) from different aqueous and food samples. A maleic anhydride-styrene-glycidyl methacrylate (MA-St-GMA) terpolymer was synthesized and characterized in detail. Experimental variables of sample preparation step were optimized using a central composite design (CCD). The final...
-
Preparation and characterization of new zinc(II) phthalocyanine — Containing poly(l-lactide)-b-poly(ethylene glycol) copolymer micelles for photodynamic therapy
Publication -
Ground Tire Rubber Modified by Ethylene-Vinyl Acetate Copolymer: Processing, Physico-Mechanical Properties, Volatile Organic Compounds Emission and Recycling Possibility
PublicationGround tire rubber (GTR) was reclaimed and modified with 10 phr of ethylene-vinyl acetate copolymer via low-temperature extrusion process. Processing, physico-mechanical properties, volatile organic compounds emission, and recycling possibility were investigated. In order to better understand the impact of used modifiers, their efficiency was compared with transpolyoctenamer, which is an additive that is commercially dedicated...
-
THE METHOD OF ANALYSIS OF DAMAGE REINFORCED CONCRETE BEAMS USING TERRESTRIAL LASER SCANNING
PublicationThe authors present an analysis of the possibility to assess deformations and mode of failure of R-C beams using terrestrial laser scanning. As part of experiments carried out at the Regional Laboratory of Construction (at Gdansk University of Technology), reinforced concrete beams were subjected to destruction by bending and by shear. The process of press impact on the reinforced concrete beam was recorded using terrestrial laser...
-
DETECTION OF DEBONDING IN STEEL BARS EMBEDDED IN CONCRETE USING GUIDED WAVE PROPAGATION
PublicationThe paper presents a non-destructive diagnostic technique based on guided wave propagation phenomenon used to assess the adhesive bonding between a steel bar and a concrete cover. Double-layered cylindrical specimens with different levels of debonding and its location were investigated. The influence of bonding length on the excitation of multiple modes of longitudinal guided waves was analysed. Numerical simulations of guided...
-
Effect of a characteristic length on crack spacing in a reinforced concrete bar under tension
Publication -
The method of analysis of damage reinforced concrete beams using terrestial laser scanning
PublicationThe authors present an analysis of the possibility to assess deformations and mechanisms of destructing bent reinforced concrete beams using the terrestrial laser scanning. As part of the experiments carried out at the Regional Laboratory of Construction of the Concrete Structures Division of the Civil and Environmental Engineering Faculty at Gdansk University of Technology, the reinforced concrete beams were subjected to destruction...
-
Electrochemical investigations of conductive coatings applied as anodes in cathodic protection of reinforced concrete
Publication -
Application of extended Finite Element Method to cracked concrete elements - numerical aspects
PublicationArtykuł omawia zastosowanie rozszerzonej metody elementów skończonych do zarysowanych elementów betonowych. Obliczenia wykonano dla elementów poddanych zginaniu i mieszanemu ściskaniu - rozciąganiu. Wyniki porównano z doświadczeniami.
-
The influence of texturing of the surface of concrete substrate on its adhesion to cement mortar overlay
Publication -
Experimental Study and Finite Element Modeling of Reinforced Concrete Column Having an Opening
Publication -
Effect of admixtures on fresh grout and two-srtage (pre-placed aggregate) concrete
PublicationPrzedstawiono rezultaty badań doświadczalnych przeprowadzonych dla betonu uzyskanego metodą dwuetapową. Główną przeszkodą szerokiego zastosowania metody betonowania dwuetapowego Polcrete była niska wydajność urządzenia wytwarzającego mikrozaprawę - ultramiksera (UM). Celem przeprowadzonych badań laboratoryjnych było dobranie odpowiednich dodatków i domieszek, które umożliwią wytworzenie mikrozaprawy o takich samych parametrach...
-
The quality management in precast concrete production and delivery processes supported by association analysis
Publication -
Investigation of Durability Properties for Lightweight Structural Concrete with Hemp Shives Instead of Aggregate
Publication -
Experimental study of corrosion in reinforced concrete by acoustic emission and electrochemical noise techniques
PublicationTechnika emisji akustycznej jest znaną metodą badań korozji zbrojenia żelbetu. Źródłem aktywności akustycznej są zawsze zjawiska o naturze mechanicznej. Przedstawiono wynik badań akustycznych zbrojonego betonu w warunkach polaryzacji anodowej, przyspieszającej procesy korozyjne. Symultanicznie prowadzona była rejestracja szumu elektrochemicznego. Dla umożliwienia korelacji wyników, uzyskanych obiema technikami, wykonana została...
-
Electrochemical investigations of conductive coatings applied as anodes in cathodic protection of reinforced concrete.
PublicationW pracy przedstawiono rezultaty badań elektrochemicznych polimerów przewodzących z pigmentem grafitowym. Wyznaczono parametry elektrochemiczne badanych powłok w trakcie długotrwałej polaryzacji zbrojonego betonu. W oparciu o pomiary impedancyjne wyznaczono parametry elektrochemiczne powłok przewodzących. Wykazano, że badane powłoki mogą być stosowane w ochronie katodowej żelbetu. Badania wykazały, że optymalne stężenie grafitu...
-
Data-Driven Modeling of Mechanical Properties of Fiber-Reinforced Concrete: A Critical Review
PublicationFiber-reinforced concrete (FRC) is extensively used in diverse structural engineering applications, and its mechanical properties are crucial for designing and evaluating its performance. The compressive, flexural, splitting tensile, and shear strengths of FRCs are among the most important attributes, which have been discussed more extensively than other properties. The accurate prediction of these properties, which are required...
-
Fire-induced spalling of ultra-high performance concrete: A systematic critical review
PublicationUltra-high performance concrete (UHPC) is a novel concrete class characterized by a compressive strength of more than 150 MPa. One of the most significant drawbacks of employing UHPC is that is very low permeability owing to its great compactness of dense structure increases the risk of fire-induced spalling. It is challenging for fire safety and structural engineers to predict and analyze this issue due to the lack of widely accepted...
-
Field Evaluation of High Modulus Asphalt Concrete Resistance to Low-Temperature Cracking
PublicationHigh-modulus asphalt concrete has numerous advantages in comparison to conventional asphalt concrete, including increased resistance to permanent deformations and increased pavement fatigue life. However, previous studies have shown that the construction of road pavements with High Modulus Asphalt Concrete (HMAC) may significantly increase the risk of low-temperature cracking. Those observations were the motivation for the research...
-
Characterization of corrosion in reinforced concrete beams using destructive and non-destructive tests
PublicationThe paper presents both non-destructive and destructive experimental tests on steel-reinforced concrete beams subjected to electrochemical corrosion. To examine the condition and behavior of the specimens, destructive tests were carried out, i.e., a three-point bending together with a modulated ultrasonic wave test. In addition, a series of non-destructive experiments were conducted, such as the potential measurement method, low-frequency...
-
Concrete Compressive Strength Under Changing Environmental Conditions During Placement Processes
PublicationThe technological process of concrete production consists of several parts, including concrete mix design, concrete mix production, transportation of fresh concrete mix to a construction site, placement in concrete framework, and curing. Proper execution of these steps provides good quality concrete. Some factors can disturb the technological process, mainly temperature and excessive precipitation. Changing daily temperature and...
-
Baseline-free debonding detection in reinforced concrete structures by elastic wave propagation
PublicationThe article presents the results of the numerical and experimental analysis concerning wave propagation in reinforced concrete (RC) beams with various extent of debonding between the steel rod and concrete cover. The main aim of the paper was to consider the unsolved research gaps, which considerably limit the application of wave-based methods in practice. The propagation of the flexural wave modes excited and registered on the...
-
Non-uniqueness of fracture parameter choice in simulations of concrete cracking at mesoscale level
PublicationIn the paper a non-uniqueness of fracture parameter choice in simulations of cracking process in plain concrete specimens at mesoscale level under monotonic static loading is analysed. The Finite Element Method is used, where cracks are defined in a discrete way using interface cohesive elements with nonlinear material law including softening. The concrete mesostructure (such as: cement matrix, air voids, aggregates, and Interfacial...
-
Machine learning-based seismic response and performance assessment of reinforced concrete buildings
PublicationComplexity and unpredictability nature of earthquakes makes them unique external loads that there is no unique formula used for the prediction of seismic responses. Hence, this research aims to implement the most well-known Machine Learning (ML) methods in Python software to propose a prediction model for seismic response and performance assessment of Reinforced Concrete Moment-Resisting Frames (RC MRFs). To prepare 92,400 data...
-
Proceedings of the fib Symposium 2019: Concrete - Innovations in Materials, Design and Structures 2019
PublicationDesigning a concrete mix is a process of synthesizing many components, it is not a simple process and requires extensive technical knowledge. The design process itself focuses on obtaining the required strength of concrete. Very often designing a concrete mix takes into account the need to maintain the proper water-demand and frost-resistance features. The parameters that influence the concrete class most significantly are the...
-
Cost Analysis of Prefabricated Elements of the Ordinary and Lightweight Concrete Walls in Residential Construction
PublicationGlobal economic growth causes an increase in natural resources exploitation, particularly in construction branch. The growing use of electricity contributes to climate change. Therefore, it is necessary to search the solutions, which will allow for reducing natural resources exploitation. One of the many opportunities to do that is the application of the recycled materials. The authors of the given article have analyzed three variants...
-
FEM and experimental investigations of concrete temperature field in the massive stemwall of the bridge abutment
PublicationThe paper deals with the prediction of early-age concrete temperature of cast-in-place stemwall of the bridge abutment. The considered object is an arch bridge located in Gda´nsk. In the case of massive structures, it is particularly important to not exceed the temperature difference between the core and the concrete surface. Too high temperature gradient generates an increase in thermal stresses, what could be the reason of exceeding...
-
Effect of Particle Size of Fly Ash Microspheres (FAMs) on the Selected Properties of Concrete
PublicationThis paper presents the investigations of selected properties of concrete containing two fractions of fly ash microspheres (FAMs) with grain size up to 200 μm and up to 500 μm. Concrete mixtures with ordinary Portland cement and three substitution rates of cement by FAMs, 1.3%, 2.0%, and 2.6%, were investigated. For all concrete mixes, the constant water–binder ratio (w/b) equal to 0.50 was used. The research program included the...
-
Internal imaging of concrete fracture based on elastic waves and ultrasound computed tomography
PublicationThe condition assessment of concrete structures belongs to the greatest challenges of non-destructive testing. Monitoring the fracture process of concrete and detecting cracks at the earliest possible stage is a vital aspect to ensure the safety of civil engineering objects. The use of ultrasound tomography enables imaging the internal structure of a tested element. This study aims at the visualization of fracture damage in concrete...
-
Experiments and calibration of a bond-slip relation and efficiency factors for textile reinforcement in concrete
PublicationTextile reinforcement yarns consist of many filaments, which can slip relative each other. At modelling of the global structural behaviour, interfilament slip in the yarns, and slip between the yarns and the concrete can be considered by efficiency factors for the stiffness and strength of the yarns, and by applying a bond-slip relation between yarns and concrete. In this work, an effective and robust method for calibration of...
-
The Impact of Homogeneity of High Modulus Asphalt Concrete Layer on Low-Temperature Cracking
PublicationDuring winter season of 2012 numerous transverse cracks developed in high-modulus asphalt concrete (HMAC) base of newly constructed motorway. Pavement cracked both in transverse joint locations and in the area between them. Research which was conducted during investigation of the causes and mechanisms of cracking consisted of: field examination, laboratory testing of specimens cored out of the existing pavement, computational analyses...